Skinning Knives, Cable Strippers, Cable Benders, Chamfering Tools

More documents

Recommendations

Info

Cable Prep Tools 268 HI-LINE UTILITY SUPPLY CO. Phone: 800-323-6606 Fax: 847-488-1285 www.hilineco.com LEAD SHEATH CABLE INSTALLATION TOOLS This integrated group of specialized tools for working with lead-sheathed cable is probably the most complete selection you can find. From furnaces and cylinders to pots and hooks, GMP has everything you need to handle your lead cable network efficiently. PRESSURE REGULATOR Cat. No. 70118 This UL listed, all-brass unit works with LP torches and furnaces during heating operations. There's a 0-60 psi outlet pressure gauge, and you can adjust the pressure 5-60 psi. Included are a POL inlet gland and nut (CGA 510), 1/4" dia. NPT opening, and a 9/16-18 LH hose outlet. Weight: 2 lbs. LP GAS HOSE Ideal for connecting a propane pressure regulator outlet to a propanepowered heater, ventilator or engine inlet. This hose features a petroleum and gas resistant rubber inner tube, an overlaying cotton or synthetic fiber and rubber outer jacket. Both ends have a spring guarded coupling. OD: 5/8" ID:1/4" Cat. No. 76791 30 ft. length. Weight: 6 lbs. 14 oz. Cat. No. 76790 10 ft. length. Weight: 2 lbs. 5 oz. If you can't find it... call HI-LINE! PROPANE FURNACE Cat. No. 70116 Unit used to heat materials used in splicing operations. This efficient solder melting furnace delivers a hefty 43,200 BTU output on just 2 lbs./hour of conventional propane. To set up the Furnace for use, connect the Pressure Regulator (70118) to the LP Gas Cylinder (70123) and the LP Gas Hose (76790) to the Regulator and Furnace. Use a Regulator Wrench (07516) to tighten all connections. 10 in. H x 8-1/2" dia. Weight: 9 lbs. 12 oz. Do not use a furnace inside a manhole or tent. FURNACE HOOD Cat. No. 70122 An accessory for the Propane Furnace, this convenient shield mounts on top of the Furnace to provide reliable heat deflection. Weight: 4 lbs. CABLE PREP TOOLS FOUR-PANEL WINDSHIELD Cat. No. 70121 Perfect for keeping wind away from lead sheath cable installation work materials, this shield features a welded steel grate and supporting brackets, providing broad support for large solder melting pots and kettles. Made of galvanized steel for corrosion resistance. Panel edges roll around 1/4" dia. rod, eliminating sharp corners.
B LEAD SLEEVE SLITTER Cat. No. 07449 This tool will make a longitudinal slit along the length of a lead sleeve to allow placement around a splice or cable sheath opening. It consists of a steel channel with two short lengths of sash chain with swivel snaps. A steel slitting wire is attached to one snap swivel, then threaded through the length of lead sleeve to be slit and then snapped onto the swivel at the other end of chain. By placing both feet on the channel as shown grasp the sleeve and draw it upward against the slitting wire. Weight: 14 oz. Cat. No. 25179 Replacement Slitting Wire LEAD SLEEVE HI-LINE UTILITY SUPPLY CO. Phone: 800-323-6606 Fax: 847-488-1285 www.hilineco.com OPENER/CLOSER Cat. No. 01148 A ratchet operated hand tool whose design facilitates working on lead sleeves. When operating the ratchet in reverse, two parallel jaws spread the sleeve apart. To close a sleeve pass the sash chain around the sleeve and attach it to the tool. Operating the ratchet will then draw the sleeve closed around the cable sheath or splice and retain a tight seam for neater soldering. Weight: 3.5 lbs. SOLDER LADLE Cat. No. 06085 A thermal handle shield isolates heat inside the 12 oz., 3-1/2" dia. cup from your hand, and keeps your thumb from slipping. Weight: 1 lb. PARAFFIN DIPPER Cat. No. 06679 This one quart dipper is built from tough 20 gauge steel, with a rolled bead around its top and pouring lip on either side. The long 9-3/4" handle is securely riveted to the body of the dipper and has a hook on one end for hanging. Weight: 1 lb. SOLDER MELTING POT Manufactured in 6" (48 fl. oz./20lb. cap.) and 8 in. (72 fl. oz./30-lb. cap.) dia. sizes from high-grade gray cast iron, these pots are designed to hold their heat. The loop on the steel bail turns freely in the ears of a pot, reducing the chance of a spill. Cat. No. Item Weight 61566 6" dia. 6 lbs. 61568 8" dia. 8 lbs. CABLE PREP TOOLS SHOWN WITH HOOK HANDLE POT HOOK HANDLE Cat. No. 07170 Ideal for carrying paraffin or solder pots to and from work sites, hanging pots from aerial cable, or suspending them from handline hooks. There's a pot hook on one end, and a cable hook and handle on the other. The entire handle is made from 3/8" steel rod. Shown above 269 Cable Prep Tools
Page 1 and 2: CABLE PREP TOOLS HI-LINE UTILITY SU
Page 3 and 4: CABLE PREP TOOLS HI-LINE UTILITY SU
Page 5 and 6: BUSHING INSERT TOOLS This model is
Page 7: 1542-2CL Stripper w/1646X Gauge Cat
Page 11: HI-LINE UTILITY SUPPLY CO. Phone: 8

Skinning Knives, Cable Strippers, Cable Benders, Chamfering Tools

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?