Drive Rods® - Norris Rods

More documents

Recommendations

Info

Type 97 Grade Steel Series Application Special Service High Strength AISI A-4330-M Nickel-Chromium-Molybdenum Alloy Steel The Type 97 is alloyed and effectively heat-treated to maximize its fatigue resistance and improve its corrosion tolerance in effectively inhibited corrosive fluids. The Type 97 grade can be utilized in some Progressing Cavity Pump (PCP) applications. The selection guide is not intended as design criteria. Call Norris for specific rod string design recommendations. Norris Drive Rods ® NORRIS TYPE 75 78 90 96 AISI Series A-4330-M Chemical Properties, % Carbon (C) Chromium Manganese Molybdenum Nickel (Cr) Copper (Cu) (Mn) (Mo) (Ni) 0.3 / 0.34 0.38 / 0.45 0.18 / 0.24 0.38 / 0.42 0.28 / 0.35 0.8 / 1.0 0.8 / 1.1 0.7 / 0.9 0.55 / 0.85 0.7 / 1.0 0.35 Max. 0.35 Max. 0.35 Max. 0.35 Max. 0.35 Max. 0.8 / 1.0 0.8 / 1.0 0.8 / 1.0 1.1 / 1.4 0.7 / 1.0 0.2 / 0.3 0.15 / 0.25 A-4142-M A-4320-M A-4138-M A-4330-M Aluminum (Al) 0.35 Max. 0.35 Max. 0.35 Max. 0.35 Max. 0.35 Max. Range 0.2 / 0.3 0.25 / 0.35 1.65 / 1.85 0.45 Max. 1.15 / 1.5 0.3 Max. 1.65 / 2.0 Niobium (Columbium) (Nb) - - - 0.27 / 0.43 - Phosphorus Silicon Sulfur (P) (Si) (S) 0.035 Max. 0.15 / 0.35 0.035 Max. 0.15 / 0.35 0.025 Max. 0.15 / 0.35 0.035 Max. 0.2 / 0.35 0.04 Max. 0.035 Max. 0.025 Max. 0.035 Max. 0.04 Max. 97 0.2 / 0.3 0.035 Max. 0.15 / 0.35 Vanadium (V) 0.04 / 0.09 0.02 / 0.07 0.04 / 0.09 0.45 / 0.65 0.04 / 0.09 Physical Properties As Normalized & Tempered Tensile Yield, 2% Offset Elongation, 8 inches Reduction, % Hardness, HRC ksi 125 / 140 120 / 140 120 / 140 Mpa ksi Mpa Range 140 / 150 140 / 150 861 / 965 827 / 965 827 / 965 965 / 1 034 965 / 1 034 100 Min. 95 Min. 95 Min. 115 Min. 115 Min. 689 Min. 655 Min. 655 Min. 792 Min. 792 Min. 10 Min. 10 Min. 10 Min. 10 Min. 10 Min. 45 Min. 45 Min. 45 Min. 45 Min. 45 Min. 25 / 31 23 / 31 23 / 31 30 / 34 30 / 34 • The above values are average values and may vary from actual measurements. • 1 inch (25,4 mm) x 30 ft. (9,14 m) Drive Rods available upon request, size and type dependent.
Pin End Color Code Maximum Torque Values for Progressing Cavity Pump Applications Drive Rod inches 1 inches 1-1/4 1-1/4 inches 1-1/2 Body Body Body Pin 1 7/8 inch (25,4m) (22,23 m) 1 1 inch (25,4m) (25,4m) 1-1/4 1 inch (31,75 m) (25,4m) 1-1/4 1-1/8 inch (31,75 m) (28,58 m) 1-1/2 1-1/8 inch (38,1 m) (28,58 m) (mm) (25,40) (mm) (31,75) (31,75) (mm) (38,1) SIZE inches 7/8 inches 1 1-1/8 inches 1-1/8 78 Dover Gray Pin Pin (mm) (22,23) Maximum 35,000 lbs (15 568,8 daN) Axial Load Pin (mm) (25,40) (28,58) Maximum 50,000 lbs (22 241,1 daN) Axial Load (mm) (28,58) Maximum 80,000 lbs (40 034,0 daN) Axial Load International Orange - 75 78 and 90 Ft-lbs. (Nm) 1,100 (1 491,4) Ft-lbs. (Nm) 2,000 (2 711,6) 2,000 (2 711,6) Ft-lbs. (Nm) 3,000 (4 067,5) Maximum Ft-lbs. (Nm) 1,110 (1 505,0) NOTICE Because Norris drive rods are specifically designed for torsional strength, Norris recommends their use in all PCP applications. Safety Red - - - - - 75 - 97 - - - - - 75 - 97 78 78 Safety Purple - Sky Blue/ Safety Purple - - - 97 - 75 75 Ft-lbs. (Nm) 2,100 (2 847,2) 2,100 (2 847,2) 75 Ft-lbs. (Nm) 78 3,150 (4 270,8) Intl. Yellow/ Safety Purple - - - - Intl. Orange/ Safety Purple 96 and 97 Ft-lbs. (Nm) 1,200 (1 627,0) • Use O’Bannon E106 solid body sucker rod elevators for 1” (25,4 mm) drive rods. Ft-lbs. (Nm) 2,500 (3 389,5) 2,500 (3 389,5) • Use O’Bannon E108 solid body elevators for 1-1/4” (31,75 mm) drive rods. 97 Ft-lbs. (Nm) 3,750 (5 084,3) • Use O’Bannon E109 solid body elevators for 1-1/2” (38,1 mm) drive rods. 75 Engineered performance. Designed tough. - - - - 97
Page 1 and 2: Drive Rods ® NORRIS Engineered per
Page 3: P002-V02-070708 Subject to change w

Drive Rods® - Norris Rods

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?