front page.xlsx - Qatar Steel Technologies

Qatar Steel Technologies 

tel. 00974 44164637 www.qsteeltech.com info@qsteeltech.com 

999C4 15052012

Qatar Steel Technologies PAGE 1 

Facts and information - working with the fittings …. 

When planning a wire construction the ultimate break load, as well as the work 

load, must be calculated, as it will determine the minimum wire size and maybe 

the wire construction needed. 

WDS fittings , unless otherwise stated, are constructed after termination to meet 

90 % of the break load on the wire ropes that are standard in the market. 

PLEASE NOTE: in order to guarantee safety in a wire construction you should calculate a safety factor 

of 2-3 on static constructions. As a general rule working loads should never exceed 25% of the break 

loads stated in this catalogue. 

For further details ask your WDS distributor. 

WDS break loads Attaching terminals 

Wire Thread Break Load Under each scheme in the WDS catalogue you will find 

mm Metr. kg. 

indications to the correct attachment. 

2,00 M4 500 

2,00 M5 800 

2,50 M5 800 

3,00 M6 1250 

4,00 M8 1300 

5,00 M10 2600 

6,00 6,00 M12 5100 

7,00 M14 5900 

8,00 M16 8000 

10,00 M20 13000 

12,00 M20 13000 

14,00 M22 17000 

16,00 M24 20000 

19,00 M27 25500 

22,00 M30 31000 

26,00 M36 43000 

For full break load WDS recomends pressing or swaging/rolling the terminals 

onto the wire ropes. 

Recommended machines for this purpose are e.g. Presses from TALURIT , or swaging machines from 

WIRETECKNIK or combined press and roller swage machines from TOPREEF 2000. Our terminals 

are however also suitable for rotary hammer pressing! 

Swageless terminals 

If the exact length of the final wire is unknown a good solution is only to swage one end and 

screw a swageless terminal onto the wire for final attachment.on site at the other end. 

Small terminals ( architectural ) 

Alternatively the WDS range of small fittings can be crimped onto the wires using a hand tool, 

however due to reduced amount of of material material in the small small fittings, only 50% break load load of the wire can be 

obtained by this method.

Swage dimention chart 

Inside Outside 

Wire Thread diam. diam. Depth 

mm metr. (+/-0,2) (+/-0,10) (+/-1,5) 

2,0 M4/M5 2,2 5,5 32 

2,5 M5 2,8 5,5 32 

3,0 M6 3,5 6,4 38 

4,0 M8 4,4 7,5 45 

5,0 M10 5,3 9,0 51 

6,0 M12 6,5 12,6 64 

7,0 M14 7,5 14,2 70 

8,0 M16 8,4 16,0 83 

10,0 M20 10,5 17,8 89 

12,0 M20 12,5 20,0 105 

14,0 M22 14,8 25,0 140 

Qatar Steel Technologies PAGE02 

After Swaging 

mm 

4,7-4,82 

4,7-4,82 

5,4-5,56 

6,23-6,35 

7,83-7,95 

10,95-11,12 

16,0 M24 17,0 28,0 160 

12,5-12,7 

14,07-14,3 

15,7-15,9 

17,6-17,8 

22,0-22,23 

25,15-25,40 

19,0 M27 20,0 34,5 200 31,44-31,75 

22,0 M30 23,5 40,5 230 36,20-36,50 

26,0 M36 27,5 46,0 280 40,97-41,28 

Correct attachment 

Always use correct size standard dies recommended by the supplier. As correct wire attachment/ 

termination can only be achieved achieved by firmly squeezing the material of the terminal into the strands 

of the wire. Most of the WDS terminals are marked with wire size and a mark indicating the 

depth of where to start for correct swaging. 

Where markings are not possible e.g. on the small terminals , the wire hole depth must be measured 

before swaging, not only to find the point to start swaging, but also to get the right length of the final 

wire including the fittings. CAUTION, by swaging the terminals onto the wire, the shaft will get a little 

longer. As a rule of thumb the length will will be prolonged by approximately the same amount of of mm 

as the diameter of wire in mm!


Tensioning of wire with terminals 

As well as serving as an attachment to the given construction, threaded 

terminals, once on to the wire, can serve as a tensioner. Where tension 

cannot be aplied to the thread via a nut at the end, the wire can be tensioned 

by use of e.g. right handed and left handed thread terminals at each end of the 

wire , by turning the whole wire it will be tensioned. 

Surface finishing of terminals 

WDS terminals are high polished , hair line finishing can be delivered upon request. 

Further information and contact 

Further information and contact 

You are kindly asked to contact your local WDS dealer/ distributor, or QST direct, should 

you any questions or need further documentation.


STAINLESS STEEL WIRE ROPES 

Stainless Steel - AISI 316 

1 x 19 construction BS MA 29 : 1982 

Art. No. d. mm T.S. KN Kg./100 

BWR11902 2 3,1 2,0 

BWR11925 2,5 4,9 3,1 

BWR11903 3 7,1 4,5 

BWR11904 4 12,6 8,0 

BWR11905 5 19,6 12,4 

BWR11906 6 28,2 17,9 

BWR11907 7 34,8 24,3 

BWR11908 8 45,5 31,8 

BWR11910 10 71,1 49,7 

BWR11912 12 102 71,3 


7 x 19 construction BS MA 29 : 1982 


BWR71902# 2 2,1 1,6 

BWR71925# 2,5 3,3 2,4 

BWR71903 3 5,0 3,8 

00703 4 8,9 6,5 

00704 55 13,9 9,1 

00705 6 20,0 13,6 

00707 8 55,6 23,9 

00709 10 80,0 40,3 

00710 12 102,0 55,0 

# acording to Din 3060 


7 7 x 7 7 construction BS MA MA 29 29 : 1982 


00696 2 2,4 1,7 

00697 2,5 3,7 2,6 

00698 3 5,3 3,9 

BWR70704 4 9,5 7,0 

BWR70705 5 14,8 10,5 

BWR70706 6 21,4 14,8 

BWR70708 8 38,0 25,5 

BWR70710 10 59,3 38,8 


7 x 19 coated white 


BCW119460 4,0-6,0 12,6 9,5 


7 x 7 coated white 


BCW707460 4,0-6,0 9,5 8,8 

BCW707480 4,0-8,0 9,5 9,5 

Tie Bar AISI 316 

Art. No. d. mm 

BTIExxx Φ 6-24

Wire Ropes standard sizes on stock 

Wire Rope Clips 


Rigging Gear Stainless steel 

Art. No. d mm Type Kgr/mtr. i.od 

01330 0,5 7x7 0,0002 8379 

01331 0,8 7x7 0,0004 8379 

00694 1,0 7x7 0,004 8379 

00695 1,5 7x7 0,009 8379 

00696 2,0 7x7 0,017 8379 

00697 2,5 7x7 0,026 8379 

00698 3,0 7x7 0,039 8379 

00703 4,0 7x19 0,065 8382 

00704 5,0 7x19 0,091 8382 

00705 6,0 7x19 0,136 8382 

00707 8,0 7x19 0,239 8382 

00709 10,0 7x19 0,403 8382 

00710 12,0 7x19 0,550 8382 

Art. No. for wire mm 

Kgr./pcs i.od 

01339 

1,00 - 2,00 

0,0006 8304 

Art. No. for wire mm 

Kgr./pcs pack i.od 

09543 2 

0,0075 0,0075 50 8248 8248 

09199 3 

0,0095 50 8248 

09200 4 

0,0135 20 8248 

09201 5 

0,0240 20 8248 

09202 6 

0,0380 20 8248 

09203 8 

0,0550 10 8248 

09204 10 

0,0930 10 8248 

09205 12 

0,2085 5 8248 

00640 14 

0,1800 5 8248 

00641 

01332 

01333 

16 

18 

22 

0,2420 5 8248 

0,3080 1 8248 

0,3570 1 8248


Architectural 

PAGE06

Domehead terminals Aisi 316 

Art.no. Wire 


Wire Design System - Stainless Steel 

Architectural 

metric L1 L2 L3 A A1 A2 Kg/100 pack iod 

B.A100003 3,0 35 25 32 3,5 5,5 8,0 0,5 50 A100003 

B.A100004 4,0 35 25 32 4,4 6,35 10,0 0,7 50 A100004 

B.A100005 5,0 41 30 37 5,3 7,5 11,5 1,0 50 A100005 

B.A100006 6,0 52 40 47 6,5 9,0 14,0 1,9 50 A100006 

Thread terminals Aisi 316 

Art.no. G Wire 

Right metric metric L1 L2 L3 D A Kg/100 pack iod iod 

B.A180503 M5 3,0 60 25 30 5,5 3,5 0,8 50 A180503 

B.A180604 M6 4,0 65 25 35 6,35 4,4 1,2 50 A180604 

B.A180605 M6 5,0 73 30 35 7,5 5,3 1,7 50 A180605 

B.A180806 M8 6,0 88 40 40 9 6,5 2,6 50 A180806 

B.A180804 M8 4,0 75 25 35 6,35 4,4 2,6 50 A180804 

Art.no. 

Left iod 

B.A190503 A190503 

B.A190604 A190604 

B.A190605 A190605 

B.A190806 A190806 

Greenline Greenline 

Break load 50 % of 1 x 19 wire 

Inside thread terminals Aisi 316 


Right metric metric L1 L2 L3 L4 D1 D2 A Kg/100 pack iod 

B.A140503 M5 3,0 65 25 20 35 7,13 5,5 3,5 1,2 50 A140503 

B.A140604 M6 4,0 65 25 20 35 8,00 6,35 4,4 1,7 50 A140604 

B.A140605 M6 5,0 70 30 20 30 8,00 7,5 5,3 2,6 50 A140605 

B.A140806 M8 6,0 85 40 25 40 11,00 9,0 6,5 6,3 50 A140806 

Art.no. 

Left iod 

B.A150503 A150503 

B.A150604 A150604 

B.A150605 A150605 

B.A150806 A150806 

Break load 50 % of 1 x 19 wire


Art.no. Wire 



Architectural 

metric L1 L2 L3 A A1 A2 Kg/100 pack iod 

B.A100003 3,0 35 25 32 3,5 5,5 8,0 0,5 50 A100003 

B.A100004 4,0 35 25 32 4,4 6,35 10,0 0,7 50 A100004 

B.A100005 5,0 41 30 37 5,3 7,5 11,5 1,0 50 A100005 

B.A100006 6,0 52 40 47 6,5 9,0 14,0 1,9 50 A100006 

Thread terminals Aisi 316 


Right metric metric L1 L2 L3 D A Kg/100 pack iod iod 

B.A180503 M5 3,0 60 25 30 5,5 3,5 0,8 50 A180503 

B.A180604 M6 4,0 65 25 35 6,35 4,4 1,2 50 A180604 

B.A180605 M6 5,0 73 30 35 7,5 5,3 1,7 50 A180605 

B.A180806 M8 6,0 88 40 40 9 6,5 2,6 50 A180806 

B.A180804 M8 4,0 75 25 35 6,35 4,4 2,6 50 A180804 

Art.no. 

Left iod 

B.A190503 A190503 

B.A190604 A190604 

B.A190605 A190605 

B.A190806 A190806 

Greenline Greenline 

Break load 50 % of 1 x 19 wire 

Inside thread terminals Aisi 316 


Right metric metric L1 L2 L3 L4 D1 D2 A Kg/100 pack iod 

B.A140503 M5 3,0 65 25 20 35 7,13 5,5 3,5 1,2 50 A140503 

B.A140604 M6 4,0 65 25 20 35 8,00 6,35 4,4 1,7 50 A140604 

B.A140605 M6 5,0 70 30 20 30 8,00 7,5 5,3 2,6 50 A140605 

B.A140806 M8 6,0 85 40 25 40 11,00 9,0 6,5 6,3 50 A140806 

Art.no. 

Left iod 

B.A150503 A150503 

B.A150604 A150604 

B.A150605 A150605 

B.A150806 A150806 

Break load 50 % of 1 x 19 wire


Art.no. Wire 



Architectural 

metric A / B D1 D2 D3 L1 L2 L3 L4 Kg/100 pack iod 

B.A200503 3,0 2,5 / 9 3,5 5,5 5,3 36 25 11 6,0 0,5 50 

B.A200504 4,0 3.0 / 10 4,4 6,4 5,3 38 25 12 6,5 0,7 50 

B.A200505 5,0 3,75/11 5,3 7,5 5,3 43 30 13 7,0 1,0 50 

B.A200506 6,0 4,5/14 6,5 9 6,3 62 40 16 8,5 1,9 50 

Breakload: 50% of 1x19 wire 

Swageless eye terminals AISI 316 

Art.no. Wire 

metric A L1 L2 L3 D2 KW Kg/100 pack iod 

B.A821903 3,0 5,0 42 36,0 13 5,3 8 50 

B.A821904 4,0 6,0 45 37,5 14,5 5,3 10 50 

B.A821905 5,0 6,0 53 44,5 18,5 6,3 12 50 

B.A821906 6,0 8,0 60 50,5 21,5 8,3 14 50 

Breakload: 50% of 1x19 wire

Swageless FORK terminals AISI 316 

Art.no. Wire 

Qatar Steel Technologies PAGE 10 


Architectural 

metric A L1 L2 L3 L4 D1 D2 KW Kg/100 pack iod 

B.A840503 3,0 5,3 45 16,5 12 5,5 11 5 8,0 50 

B.A840504 4,0 6,3 48 18,0 14 7 15 5 10,0 50 

B.A840605 5,0 6,3 56 22,0 18 8 16 6 12,0 50 

B.A840806 6,0 8,3 62 24,5 20 8,5 18 8 14,0 50 


Fork terminals - Machined Aisi 316 

Art.no. Wire 

metric L1 L2 L3 L4 D1 D2 D3 D4 A Kg/100 iod 

B.A390503 3,0 41,0 30 25,0 6 5 11 5,5 3,5 5,5 1,03 

B.A390504 4,0 43,0 31 25,0 8,5 5 13 6,35 4,4 6,5 1,43 

B.A390505 5,0 51,0 36 30,0 8 5 13 7,5 5,3 6,5 2,23 

B.A390606 6,0 67,0 42 40,0 11 6 16 9 6,5 8,5 3,66 


Fork Thread - Machined Aisi 316 

Art.no. 



Architectural 

Right G L1 L2 L3 L4 D1 D2 D3 A Kg/100 pack iod 

B.A370503 M5 34,0 24 27,0 6 5 11 8 5,5 1,4 50 

B.A370604 M6 44,0 30 35,0 8,5 5 13 8,00 6,5 1,9 50 

B.A370806 M8 52,0 35 40,0 11 6 16 11 8,5 2,2 50 


Art.no. 

Left 

B.A380503 

B.A380604 

B.A380806 

Thread Fork - Machined Aisi 316 

Art.no. 

Right G L1 L2 L3 D1 D2 A Kg/100 pack iod 

B.A421205 M5 42,5 31 6,0 5 11 5,5 1,1 50 

B.A421206 M6 48,0 36 8,5 5 13 6,5 1,4 50 

B.A421208 M8 61,0 42 11,0 6 16 8,5 1,9 50 


Art.no. 

Left 

B.A431205 

B.A431206 

B.A431208

Cone Terminals Aisi 316 

Qata5r Steel Technologies PAGE12 


Architectural 

Art.no. wire L1 L2 L3 A A1 A2 Kg/100 pack iod 

B.A110003 3,0 35,0 25 32,5 3,5 5,5 8 0,5 50 

B.A110004 4,0 35,0 25 32,0 4,4 6,4 10 0,7 50 

B.A110005 5,0 41,0 30 38,0 5,3 7,5 12 1 50 

B.A110006 6,0 52,0 40 48,5 6,5 9 14 1,9 50 


Inside Thread Fork Welded Aisi 316 

Art.no. 

Right wire G L1 L2 L3 D1 D2 A Kg/100 pack iod 

B.A340503 3,0 M5 59 25,0 12 5 7,1 7,5 1,4 50 

B.A340504 4,0 M6 67 30,0 12 5 8 7,50 1,9 50 

B.A340605 5,0 M6 68 30,0 13 6 8 9,5 2,2 50 

B.A340806 6,0 M8 79 35,0 15 8 11 11 4,5 50 


Art.no. 

Left 

B.A350503 

B.A350504 

B.A350605 

B.A350806

Domehead inside thread Aisi 316 

Art.no. 



Architectural 

right G L1 L2 L3 A1 A2 Kg/100 pack iod 

B.A170503 M5 43 40 25 7,13 10,0 0,5 50 A170503 

B.A170604 M6 49 45 30 8,00 11,5 0,7 50 A170604 

B.A170806 M8 60 55 35 11,00 14,0 1,0 50 A170806 

Fork terminals , welded Aisi 316 

Art.no. Wire 

metric G L1 L2 L3 D A Kg/100 pack iod 

B.A360503 3,0 3,0 3,5 3,5 50 25 12 55 7,5 1,0 50 50 A360503 

B.A360604 4,0 4,4 50 25 12 5 7,5 1,5 50 A360604 

B.A360605 5,0 5,3 58 30 13 6 9,5 2,2 50 A360605 

B.A360806 6,0 6,5 72 40 15 8 11,0 3,7 50 A360806 

Thread forks , welded Aisi 316 Break load 50 % of 1 x 19 wire 

Art.no. G 

Right metric L1 L2 L3 D1 A Kg/100 pack iod 

B.A320503 M5 49 30 12 5,0 7,5 1,4 50 A320503 

B.A320604 M6 54 35 12 5,0 7,5 2,0 50 A320604 

B.A320605 M6 56 35 13 6,0 9,5 2,5 50 A320605 

B.A320806 M8 65 40 15 8,0 11,0 3,5 50 A320806 

Art.no. 

Left iod 

B.A330503 A330503 

B.A330604 A330604 

B.A330605 A330605 

B.A330806 B.A330806 A330806

Rigging Screws Fork - Fork Aisi 316 L 



Architectural 

Art.no. G L1 L2 L3 D A Kg/100 pack iod 

B.A12120505 M5 143,0 106 12,0 5 7,5 3,7 50 

B.A12120506 M6 155,0 111 12,0 5 7,5 5,7 50 

B.A12120606 M6 159,0 115 13,0 6 9,5 6,7 50 

B.A12120808 M8 186,0 140 15,0 8 11 11,3 50 

B.A12121010 M10 204,0 157 15,0 8 11 19,2 20 

B.A12121212 M12 228,0 180 19,5 9,5 12,5 32,1 10 


Rigging Screws Fork - Terminal Aisi 316L 

Art.no. wire G L1 L2 L3 L4 D1 D2 D3 A Kg/100 iod 

B.A120305 3,0 M5 153 117 12 25 5 5,5 3,5 7,5 3,1 

B.A120406 4,0 M6 166 122 12 25 5 6,40 4,4 7,5 4,9 

B.A120506 5,0 M6 176 132 13 30 6 7,5 5,3 9,5 5,9 

B.A120608 6,0 M8 209 163 15 40 8 9 6,5 11 10,4 

B.A120810 8,0 M10 235 187 15 50 8 12,6 8,4 11 18,7 

B.A121012 10,0 M12 264 216 19,5 60 9,5 16 10,5 12,5 31,8 


Thread Eyes Aisi 316 

Art. No. 



Architectural 

Right G D1 L1 L2 L3 L4 A B Kg/100 pack iod 

B.A440505 M5 5,3 41 30,0 11 6 2,5 9 0,6 50 

B.A440506 M6 5,3 48 35,0 13 7 3,8 11 1,2 50 

B.A440606 M6 6,3 48 35,0 13 7 3,8 11 1,2 50 

B.A440608 M8 6,3 57 40,0 16 8,5 4,5 15 2,2 50 


Art. No. 

Left 

B.A450505 

B.A450506 

B.A450606 

B.A450608 

Screw Eyes Aisi 304 

Art.no. L1 L2 L3 A Φ D Kg/100 iod 

B.A433553 48 24 12 3 5 5,3 0,78 

B.A434063 60 35 13 3,8 6 6,30 1,32

Net clip Aisi 316 

Art.no. Wire 



Architectural 

Right metric G L L1 L2 L3 KW Kg/100 pack iod 

B.A600003C 3,0 M10 19 5 8 3,2 17,0 2,4 50 A600003 

B.A600004C 4,0 M12 21 5 8 4,2 20,0 3,6 50 A600004 

B.A600005C 5,0 M12 23 5 10 5,2 20,0 3,6 50 A600005 

B.A600006C 6,0 M12 25 5 10 6,2 20,0 5,8 50 A600006 

B.A600008O 8,0 M16 36 6 14 8,3 26,0 8,8 50 A600008 

Net clip Aisi 316 through-going thread 

Art.no. Wire 

Right metric G L L1 L2 L3 KW Kg/100 pack iod 

B.A610003C 3,0 M10 19 5 8 3,2 17,0 2,4 50 A610003 

B.A610004C 4,0 M12 21 5 8 4,2 20,0 3,6 50 A610004 

B.A610005C 5,0 M12 23 5 10 5,2 20,0 3,6 50 A610005 

B.A610006C 6,0 M12 25 5 10 6,2 20,0 5,8 50 A610006 

B.A610008O B.A610008O 8,0 M16 36 6 14 14 8,3 26,0 8,8 50 50 A610008 

Flexible net clip Aisi 316 

Art.no. wire 

size L1 L2 rotation Dg Kg/100 pack iod 

B.022404 4,0 20 8 360 2,7 50 022404 

B.022406 6,0 24 10 360 2,9 50 022406 

L1 L1



Architectural

Architecture ball stopper Aisi 303 

Wire G 



Architectural 

Art.no. metric metric D D1 Kg/100 pack iod 

B.A260003 3,0 M4 15,0 3,5 1,2 50 A260003 

B.A260004 4,0 M5 20,0 4,5 3,0 50 A260004 

B.A260005 5,0 M5 20,0 5,5 2,9 50 A260005 

B.A260006 6,0 M6 25,0 6,5 5,7 50 A260006 

Architecture ball Aisi 303 

Art.no. Wire G 

Right metric metric D L Kg/100 pack iod 

B.A240503 3,0 M4 15,0 12,0 1,9 50 A240503 

B.A240503X 3,0 M5 20,0 16,0 2,9 50 A240503X 

B.A250605 4,0/5,0 M5 20,0 16,0 2,9 50 A250605 

B.A240806 6,0 M6 25,0 20,0 5,7 50 A250806 

02155 - M8 40,0 50 

02820 - M8 50,0 50 

Architecture ball for dome head screw Aisi 303 

Art.no. Thread 

metric D D1 Kg/100 pack iod 

B.A270503 M5 15,0 5,3 1,20 50 A270503 

B.A270604 M6 20,0 6,3 2,94 50 A270604 

B.A250806 B.A250806 M8 25,0 8,5 5,68 50 A250806 A250806 

B.A271008 M10 30,0 10,5 9,72 50 A271008

Architectural 

Architecture ball For through - going thread Aisi 303 

Wire G 



Art.no. metric metric D Kg/100 pack 

B.A250503 3,0 M5 15,0 1,9 50 

B.A250503X 3,0 M5 20,0 2,9 50 

B.A250605 4,0/5,0 M6 20,0 2,9 50 

B.A250806 6,0 M8 25,0 5,7 50 

Swageless thread terminals Aisi 316 

Wire G 

Art.no. metric metric L1 L2 L3 KW KW1 Kg/100 pack 

B.A800305 3,0 M5 63 40 31 8,0 8,0 0,0 50 

B.A800406 4,0 M5 69 46 35 10,0 10,0 0,0 50 

B.A800506 5,0 M6 73 47 35 12,0 11,0 0,0 50 

B.A800608 6,0 M8 M8 83,5 54,5 41 41 14,0 13,0 0,0 50 50 


Architectural 

Architecture ball for dome head terminal Aisi 303 

Wire 



Art.no. metric D D1 Kg/100 pack iod 

B.A280003 3,0 15,0 6,0 2,00 50 A280003 

B.A280004 4,0 20,0 7,0 2,94 50 A280004 

B.A280005 5,0 20,0 8,0 5,68 50 A280005 

B.A280006 6,0 25,0 9,5 5,68 50 A280006 

Sleeve for WDS ball Aisi 316 

Wire Wire 

For Domehead 

Art.no. size D1 D2 D3 L1 L2 Kg/100 pack iod 

B.A292008 3-4-5 27 20 23 10,0 2,0 1,05 50 A292008 

B.A292510 6 32 25 28 13,0 3,0 1,80 50 A292510 

Flexible Angle Hinge Aisi 316 

Wire 

Art.no. size D1 D2 L1 G NV Kg/100 pack iod 

B.A232005 3 8 20 32 M5 7,0 3,7 50 A232005 

B.A232006 4-5 8 20 32 M6 7,0 3,4 50 A232006 

B.A232008 6 11 25 36 M8 10,0 6,8 50 A232008

Body Aisi 316 

G 



Architectural 

Art.no. metric L1 D1 Kg/100 pack iod 

B.A011205 M5 60,0 8,0 0,90 50 A011205 

B.A011206 M6 65,0 10,0 1,70 50 A011206 

B.A011208 M8 80,0 14,0 4,30 50 A011208 

B.A011210 M10 90,0 17,0 7,00 50 A011209 

B.A011212 M12 100,0 23,0 11,30 50 A011210 

Stop end nut Aisi 316 

G 


Art.no. metric D1 D2 L1 L2 Kg/100 pack iod 

B.A160503 M5 8 12 33,0 30,0 0,8 50 A160503 

B.A160604 M6 8 12 39,0 35,0 0,85 50 A160604 

B.A160806 M8 10 14 45,0 40,0 1,2 50 A160806 

B.A161008 M10 13 17 50,0 45,0 2,5 50 A161008 

Stopper Aisi 304 

Wire G 


Art.no. metric metric L L1 L2 B Kg/100 pack iod 

B.A650003 3 M3 15 3 2,5 10,0 1,4 50 A650003 

B.A650004 4 M3 15 4 3,0 10,0 1,4 50 A650004 

B.A650005 5 M3 20 5 4,0 10,0 2,1 50 A650005 

B.A650006 6 M3 20 6 5,0 10,0 2,1 50 A650006 

B.A650008 8 M4 23 8 7,0 12,0 2,6 50 A650008

Spring terminal Aisi 316 

wire 



Architectural 

Art.no. size flexibility 

G L1 D1 Break Load Kg/100 pack iod 

B.022304 3-4 26,0 

60,0 8,0 0-150 Kg. 

50 022304 

Swageless terminal Aisi 316 

Stop inside thread 

wire 

L 

D G 

Art.no. size L D NW G Tighten Kg/100 pack iod 

B.A520803 3 27 8 7 M6X16mm 10 NM 

50 A520803 

B.A521104 

long inside thread 

4 35 11 10 M8X21mm M8X21mm 18 18 NM 

50 A521104 

wire 

Art.no. size L D NW G Tighten Kg/100 pack iod 

B.A540803 3 37 8 7 M6X26mm 10 NM 

50 A540803 

B.A541104 4 48,5 11 10 M8X32mm 18 NM 

50 A541104 

Swivel terminal Aisi 316 

Wire 

NW 

L 

Art.no. size G L1 L2 L3 D NV Kg/100 pack iod 

B.A900305 3 M5 81 30 30,0 5,5 4,5 1,4 50 A900305 

B.A900406 4 M6 88 31 35,0 6,4 5,0 1,9 50 A900406 

B.A900506 5 M6 100 37 35,0 7,5 6,0 2,8 50 A900506 

B.A900608 6 M8 119 48 40,0 9,0 7,0 5,0 50 A900608 

D 

D2 

L1 

NV 

G 

L3 

G 


D 

Free Rotation

Angle Hinge Aisi 303 



Architectural 

Art.no. α D1 D2 L Kg/100 pack 

B.A302003 20,0 11,0 5 5 0,4 50 

B.A302503 25,0 11,0 5 5 0,4 50 

B.A303003 30,0 11,0 5 5 0,5 50 

B.A303503 35,0 11,0 5 5 0,6 50 

B.A304003 40,0 11,0 5 5 0,6 50 

B.A302004 20,0 13,0 6 5 0,6 50 

B.A302504 25,0 13,0 6 5 0,7 50 

B.A303004 30,0 13,0 6 5 0,8 50 

B.A303504 35,0 13,0 6 5 0,8 50 

B.A304004 40,0 13,0 6 5 0,9 50 

B.A302006 20,0 17,0 8,2 5 1,2 50 

B.A302508 25,0 17,0 8,2 5 1,2 50 

B.A303006 30,0 17,0 8,2 5 1,3 50 

B.A303506 35,0 17,0 17,0 8,2 8,2 5 1,5 50 

B.A304006 40,0 17,0 8,2 5 1,6 50 

Only on request 

Angle Hinge for Cone terminals Aisi 303 

Art.no. α D1 D2 L L1 Kg/100 pack 

B.A312003 20,0 11,0 6 5 1 0,4 50 

B.A312503 25,0 11,0 6 5 1 0,4 50 

B.A313003 30,0 11,0 6 5 1 0,5 50 

B.A313503 35,0 11,0 6 5 1 0,6 50 

B.A314003 40,0 11,0 6 5 1 0,6 50 

B.A312004 20,0 13,0 7 5 1 0,6 50 

B.A312504 25,0 13,0 7 5 1 0,7 50 

B.A313004 30,0 13,0 7 5 1 0,8 50 

B.A313504 35,0 13,0 7 5 1 0,8 50 

B.A314004 40,0 13,0 7 5 1 0,9 50 

B.A312005 20,0 14,0 8 5 1 0,8 50 

B.A312505 25,0 14,0 8 5 1 0,9 50 

B.A313005 B.A313005 30,0 14,0 14,0 8 5 1 0,9 50 

B.A313505 35,0 14,0 8 5 1 1,0 50 

B.A314005 40,0 14,0 8 5 1 1,1 50 

B.A314006 20,0 17,0 10 5 1 1,2 50 

B.A312506 25,0 17,0 10 5 1 1,2 50 

B.A313006 30,0 17,0 10 5 1 1,3 50 

B.A313506 35,0 17,0 10 5 1 1,5 50 

B.A314006 40,0 17,0 10 5 1 1,6 50 

Only on request

Curtain anchors Aisi 304 

Wire 



Architectural 

Art.no. size L1 L2 D1 D2 Break load Kg/100 pack iod 

B.IX1085 3 81 30 30,0 5,5 500 Kg. 0,0215 50 IX1085 

B.IV1085 3 88 31 35,0 6,4 500 Kg. 0,0750 50 IV1085 

B.IY1305 3 100 37 35,0 7,5 500 Kg. 0,0675 50 IY1305 

Incl. double headed Clevis Pins 

B.IX1085 B.IV1085 B.IY1305 

Use max. M5 thread terminals for 3 mm wire


Wire Design System - Stainless Steel

PAGE26 Qatar Steel Technologies PAGE26 

Wire Design System - Stainless Steel

Green line system Aisi 316 

Top Base 

Wire 



Art.no. metric L1 L2 G1 G2 Kg/100 pack iod 

B.211004M 4,0 130 110 M8 M8 1 211004M 

B.211006M 6,0 130 110 M8 M8 1 211006M 

Bottom base 

Wire 

Art.no. metric L1 L2 G1 FLEX Kg/100 pack iod 

B.221004M 4,0 130 100 M8 26 1 221004M 

B.221006M 6,0 130 100 M8 26 1 221006M 

Flex. Support post 

Top base Bottom base 

Art.no. 

Wire 

metric L1 L2 G1 

o 

Dg. o 

Kg/100 pack iod 

B.042404 4,0 110 100 M8 360 1 042404 

B.042406 6,0 110 100 M8 360 1 042406

Green line system Aisi 303 

Green line Post 



Art.no. G1 G2 D1 D2 D3 L1 L2 L3 L4 Kg/100 pack iod 

B.08164095 M8 M6 40 16 6 95 30 19 9 19,40 1 

Load 

100 Kg. 

Green Green Line is a wire trellis system with a long lifetime, which 

requires no maintenance after installation. 

Green line trellis is not only a decorative addition to any façade. 

It protects the façade against damp and dirt and in addition has 

a noise-reducing and insulating effect. 

All the system requires is firm anchoring in the brickwork. 

In most cases it can be installed with the help of standard 

products from a DIY market.



SHELF 

SYSTEMS SYSTEMS 

WDS

DIY Sign Adjuster 

Art.no. Wire 



Architectural 

right size G D1 D2 D3 L1 L2 L3 L4 Kg/100 pack iod 

B.A64DH06 3,0 M6 11 22 6 72,0 24,0 36 50,0 5,70 50 A64DH06 

Art.no. Break 

left L5 load kg. iod 

B.A64Dv06 40,0 300 A64Dv06 

Terminal Aisi 304 

Art.no. Wire KG. 

Example with 2pcs RH thread 

and 2 pcs LH thread 

right size G D1 L1 L2 L3 L4 B.L. Kg/100 pack iod 

B.A640305 3,0 M5 11 53 8 36,0 34,0 300 3,40 50 A640305 

B.A640406 4,0 M6 13 58 9 38,0 37,0 400 5,40 50 A640406 

B.A640506 5,0 M6 14 65 9 45,0 37,0 500 6,80 50 A640506 

B.A640608 6,0 M8 16 73 12 47,0 45,0 600 10,70 50 A640608 

The DIY terminal has inside thread 

delivered with removable thread pin

Architectural 

Swageless dual/inside thread terminal Aisi 304 

Art.no. Wire 



size D1 D2 L1 L2 L3 L2 L4 L4 Kg/100 pack iod 

B.83220306 3,0 22,0 6 39 18 70,0 24,0 36 60,0 4,40 50 8,3E+07 

B.83220406 4,0 22,0 6 46 18 70,0 24,0 36 60,0 5,40 50 8,3E+07 

Break Load 700 Kg. 

Note: All break loads are determined by wedges ( jaws ) and thread.. Guarantees at least 85% break 

load on the wire. 

Shelf systems 

Art.no. SHELF SHELF 

DEPTH mm LOAD Kg/100 pack 

B.ASHELF1 200 50 kg. 1 

B.ASHELF2 300 50 kg. 1 

iod 

ASHELF1 

ASHELF2 

Delivered exclusive wire & shelf components 

Art.no. covers Articles for mounting one shelf 

side only. 

Mount to wall with 6mm dual thread screws. 

X 1 

X 2 

Bottom base delivered with 

Spec. 3mm DIY & thread 

terminals. 

X 1

WDS 3mm Wire Shelf Components 

Art.no. Wire Glass Wood 


Wire Design System 

Architectural 

Max load 

size size mm size mm kg. 

Grips 

Kg/100 pack iod 

B.A63103 3,0 max 8 - 50 Single glass horizontal 50 A63103 

B.A63203 3,0 max 8 - 50 Single glass Swivel 

50 A63203 

B.A63303 3,0 - 20-40 50 Single wood Swivel 

50 A63303 

16 

Swaging tool 

30 

B.A63103 B.A63203 B.A63303 

Glass size 

Art.no. wire size swaging kg. 

16 Glass size 6 

mm diam. Mm 1 iod 

ARCTOOL8 3,0+4,0 mm 5,5-6,35 mm 1,70 ARCTOOL8 

For use on flexible wire only ( 7x7 & 7x19 ) 

Swaging tool 

Art.no. wire size swaging kg. 

mm diam. Mm 1 iod 

ARCTOOL1 3,0+6,0 mm 5,5-9,0 mm 5,00 ARCTOOL1 

Wire rope cutter 

Art.no. wire size 

kg. 

max mm 1 iod 

ARCTOOL5 6 

0,71 ARCTOOL5 

ARCTOOL6 7 1,5 

ARCTOOL7 9 2,8 

35 

16 

30

Cover Disk Aisi 316 


Wire Design System 

Architectural 

Art. No. D1 D2 D3 Kg/100 pack 

B.A500003 15,0 5,5 3 0,35 50 

B.A500004 20,0 6,5 4 0,85 50 

B.A500006 25,0 8,5 4 1,3 50 

Pls Refer to to our Fasteners Catalogue

Rigging screws welded Fork - Fork Aisi 316 

Art.no. G L1 L2 A D B.L. 


Structural 

metric kg Kg/100 pack iod 

B.120004 M4 156 106 6,5 4,0 500 3,3 10 120004 

B.120005 M5 180 126 7,5 5,0 800 5,1 10 120005 

B.120006 M6 200 138 7,5 5,0 1250 9,0 10 120006 

B.120008 M8 234 158 9,5 6,0 1300 14,0 10 120008 

B.120008X M8 240 166 11 8,0 2350 15,0 10 120008X 

B.120010 M10 272 188 11 8,0 2600 24,0 10 120010 

B.120010X M10 280 196 12 9,5 3500 26,0 10 120010X 

B.120012 M12 350 244 14 12,0 5100 52,5 5 120012 

B.120014 M14 387 267 14 12,0 5900 63,5 5 120014 

B.120016 M16 446 313 18 14,0 8000 100,0 5 120016 

B.120016L M16 442 309 22 14,0 8000 100,0 5 120016L 

B.120020 M20 550 390 24 19,0 13000 197,0 BULK 120020 

B.120020L M20 546 386 30 19,0 13000 197,0 BULK 120020L 

B.120022 ! M20 653 472 30 22,0 17000 448,0 BULK 120022 

B.120024 ! M24 769 536 30 25,4 20000 638,0 BULK 120024 

Rigging screws machined Fork - Fork Aisi 316 

Art.no. G L1 L2 A D B.L. 

! Bodie with bronze inserts 


B.740020 M20 619 453 20 19,0 13000 330,0 BULK 740020 

B.740022 M22 637 456 22 22,0 17000 892,0 BULK 740022 

B.740024 M24 763 530 25 25,0 20000 1193,0 BULK 740024 

B.740027 M27 813 578 30 28,0 25500 1803,0 BULK 740027 

B.740030 M30 918 656 35 32,0 31000 2614,0 BULK 740030 

B.740036 M36 970 696 35 35,0 43000 3390,0 BULK 740036 

Note : All break loads are determined by clevis pin and thread. 

The user is responsible for choosing the proper cable diameter and for correct assembly.

Rigging screws welded Eye - Fork Aisi 316 


Structural 

Art.no. G L1 L2 L3 D1 D2 D3 A1 A2 B.L. 


B.191204 M4 156 104 9,5 4,0 4,5 10,0 6,5 3,0 500 2,8 bulk 

B.191205 M5 188 129 12,0 5,0 5,5 12,0 7,5 3,0 800 4,2 bulk 

B.191206 M6 206 138 12,0 5,0 6,5 14,0 7,5 4,0 1300 6,3 bulk 

B.191208 M8 244 164 13,0 6,0 8,5 17,0 9,5 5,0 2350 13,0 bulk 

B.191210 M10 271 188 15,0 8,0 10,5 21,0 11,0 6,0 3500 21,9 bulk 

B.191212 M12 343 235 25,0 12,0 13,0 25,0 14,5 8,0 5100 44,0 bulk 

B.191214 M14 381 262 25,0 12,0 13,0 28,0 14,5 9,0 5900 60,0 bulk 

B.191216 M16 426 296 33,0 14,0 14,5 31,0 18,0 10,0 8000 85,6 bulk 

B.191220 M20 518 364 50,0 19,0 19,5 40,0 24,0 15,0 13000 169,3 bulk 

B.191222 ! M22 625 444 57,0 22,0 23,0 47,0 30,0 18,0 17000 398,5 bulk 

B.191224 ! M24 741 508 62,0 25,4 26,0 53,0 30,0 20,0 20000 580,0 bulk 

Note : All break loads are determined by clevis pin ( D1 ) , eye ( D2 ) & thread 

The user is responsible for choosing the proper cable diameter and for correct assembly. 

! Bodie with bronze inserts

Rigging screws Eye - Eye Aisi 316 


Structural 

Art.no. G L1 L2 D1 D2 A B.L. 


B.191904 M4 158 106 4,5 10,0 3,0 500 3 10 

B.191905 M5 190 131 5,5 12,0 3,0 800 4 10 

B.191906 M6 204 136 6,5 14,0 4,0 1300 11 10 

B.191908 M8 244 164 8,5 17,0 5,0 2350 14 5 

B.191910 M10 270 187 10,5 22,0 6,0 3500 23 5 

B.191912 M12 334 226 13,0 25,0 8,0 5100 38 5 

B.191914 M14 376 257 13,0 28,0 9,0 5900 51 bulk 

B.191916 M16 408 278 14,5 31,0 10,0 8000 73 bulk 

B.191920 M20 488 334 19,5 40,0 15,0 13000 105 bulk 

B.191922! M22 597 416 23,0 47,0 18,0 17000 354 bulk 

B.191924! M24 713 480 26,0 53,0 20,0 20000 670 bulk 

B.191927! M27 759 527 28,5 65,0 25,0 27000 710 bulk 

B.191930! M30 861 581 33,0 70,0 30,0 31000 991 bulk 

B.191936! B.191936! M36 892 618 36,0 80,0 30,0 43000 1288 1288 bulk 

Note : All break loads are determined by clevis pin ( D1 ) , eye & thread 



Rigging screws Eye - Terminal Aisi 316 


Structural 

Art.no. G L1 L2 D1 D2 A B.L. 

wire kg Kg/100 pack iod 

B.190204 2,0 M4 188 136 2,2 4,3 5,5 500 3,0 bulk 

B.190205 2,0 M5 213 151 2,2 5,5 5,5 800 3,7 bulk 

B.192505 2,5 M5 213 151 2,8 5,5 5,5 800 3,4 bulk 

B.190306 3,0 M6 234 166 3,5 6,5 6,4 1300 6,3 bulk 

B.190406 4,0 M6 244 176 4,4 6,5 7,5 1300 6,7 bulk 

B.190408 4,0 M8 282 202 4,4 8,5 7,5 2350 12,4 bulk 

B.190508 5,0 M8 288 208 5,3 8,5 9,0 2350 13,4 bulk 

B.190510 5,0 M10 311 227 5,3 10,5 9,0 3500 19,5 bulk 

B.190610 6,0 M10 326 242 6,5 10,5 12,6 3500 23,4 bulk 

B.190612 6,0 M12 379 271 6,5 13,0 12,6 5400 38,5 bulk 

B.190712 7,0 M12 387 279 7,5 13,0 14,2 5400 40,8 bulk 

B.190812 8,0 M12 400 292 8,4 13,0 16,0 5400 51,1 bulk 

B.190714 7,0 M14 432 314 7,5 13,0 14,2 5600 46,7 bulk 

B.190814 8,0 8,0 M14 446 328 8,4 13,0 16,0 5600 5600 55,1 bulk 

B.190816 8,0 M16 478 350 8,4 14,5 16,0 7600 74,6 bulk 

B.191016 10,0 M16 495 367 10,5 14,5 17,8 7600 86,6 bulk 

B.191020 10,0 M20 593 405 10,5 19,3 17,8 13000 126,9 bulk 

B.191220 12,0 M20 573 419 12,5 19,5 20,0 13000 136,9 bulk 

B.191220X 12,0 M20 599 435 12,5 19,5 21,4 13000 152,8 bulk 

B.191422X! 14,0 M22 708 527 14,8 23,0 25,0 17000 163,8 bulk 

B.191624X! 16,0 M24 846 613 17,0 26,0 28,0 20000 233,6 bulk 

B.191927X! 19,0 M27 934 934 702 20,0 29,0 34,5 27000 394,0 bulk 

B.192230X! 22,0 M30 1057 777 23,5 33,0 40,5 31000 1090 bulk 

B.192636X! 26,0 M36 1150 873 27,5 36,0 46,0 43000 1447 bulk 

Note : All break loads are determined by ( D2 ) eye & thread 



Rigging screws Toggle - Terminal Aisi 316 


Structural 

Art.no. L1 L2 L3 L4 L5 D1 D2 B.L. 

G wire kg Kg/100 pack iod 

B.320306 M6 3 271 201 16,0 8,0 8,0 6,4 6,4 1250 bulk 

B.320408 M8 4 310 240 20,0 9,0 10,0 8,0 7,5 2350 bulk 

B.320510 M10 5 361 278 24,0 12,0 12,0 9,5 9,0 3500 bulk 

B.320612X M12 6 448 340 31,0 18,0 18,0 12,7 12,6 5100 bulk 

B.320712X M12 7 456 348 31,0 18,0 18,0 12,7 14,2 5100 bulk 

B.320812X M12 8 471 363 31,0 18,0 18,0 12,7 16,0 5100 bulk 

B.320816X M16 8 566 436 37,0 20,0 20,0 16,0 16,0 8000 bulk 

B.321020X M20 10 642 488 40,0 25,0 24,0 19,0 17,8 13000 bulk 

B.321220 M20 12 661 507 40,0 25,0 24,0 19,0 20,0 13000 bulk 

B.321220X M20 12 677 523 40,0 25,0 24,0 19,0 21,4 13000 bulk 

B.321422X! M22 14 808 627 46,0 30,0 26,0 22,0 25,0 17000 bulk 

B.321624X! M24 16 963 730 53,0 37,0 29,0 25,4 28,0 23000 bulk 

B.321927X! M27 19 1071 836 60,0 34,0 34,0 28,0 34,5 25500 bulk 

B.322230X! B.322230X! M30 22 1193 931 70,0 41,5 40,0 32,0 40,5 31000 bulk 

B.322636X! M36 26 1319 1045 80,0 41,0 44,0 36,0 46,0 43000 bulk 

Note : All break loads are determined by ( D1 ) CLEVIS PIN & thread 



Rigging screws Terminal - Terminal Aisi 316 


Structural 

Art.no. L1 L2 D1 D2 B.L. 


B.120205T M5 2 239 178 5.5 2,2 500 4 bulk 

B.122505T M5 3 239 178 5,5 2,8 800 4 bulk 

B.120306T M6 3 274 204 6,4 3,5 1250 6 bulk 

B.120406T M6 4 284 214 7,5 4,4 1250 8 bulk 

B.120408T M8 4 312 242 7,5 4,4 2350 13 bulk 

B.120508T M8 5 328 256 9,0 5,3 2350 15 bulk 

B.120510T M10 5 350 267 9,0 5,3 3500 21 bulk 

B.120610T M10 6 380 297 13,0 6,5 3500 21 bulk 

B.120612T M12 6 410 327 13,0 6,5 5100 42 bulk 

B.120712T M12 7 454 346 14,0 7,5 5100 47 bulk 

B.120714T M14 7 488 369 14,0 7,5 5900 57 bulk 

B.120812T M12 8 490 382 16,0 8,4 5100 55 bulk 

B.120814T M14 8 521 402 16,0 8,4 5900 65 bulk 

B.120816T B.120816T M16 8 548 418 16,0 8,4 8000 8000 83 bulk 

B.121016T M16 10 566 436 18,0 10,5 8000 87 bulk 

B.121020T M20 10 620 466 18,0 10,5 13000 135 bulk 

B.121220T M20 12 658 504 20,0 12,5 13000 149 bulk 

B.121422T! M22 14 820 639 25,0 14,8 17000 378 bulk 

B.121622T! M22 16 870 689 28,0 17,0 17000 416 bulk 

B.121624T! M24 16 979 746 28,0 17,0 20000 553 bulk 

B.121927T! M27 19 1114 879 35,0 20,0 27000 801 bulk 

B.122230T! M30 22 1245 983 41,0 23,5 31000 1179 bulk 

B.122636T! M36 26 1402 1128 46,0 27,5 43000 1589 bulk 

Note : All break loads are determined by thread. 



Rigging screws Swageless - Blank Aisi 316 


Structural 

Art.no. L1 L2 NV1 NV2 B.L. 


B.870306 M6 3 168 134 12,0 10,0 750 6,0 bulk 

B.870406 M6 4 175 141 14,0 12,0 1300 6,7 bulk 

B.870408 M8 4 202 162 14,0 12,0 1500 11,6 bulk 

B.870508 M8 5 211 171 16,0 13,0 2180 13,8 bulk 

B.870510 M10 5 222 181 16,0 13,0 2180 18,5 bulk 

B.870610 M10 6 233 192 19,0 16,0 3500 22,7 bulk 

B.870612 M12 6 277 223 19,0 16,0 3700 33,5 bulk 

B.870714 M14 7 311 253 21,0 18,0 4700 44,1 bulk 

B.870812 M12 8 294 240 24,0 19,0 5400 43,5 bulk 

B.870814 M14 8 320 262 24,0 19,0 5600 49,5 bulk 

B.870816 M16 8 348 283 24,0 19,0 5600 63,1 bulk 

B.871016 M16 10 356 291 27,0 24,0 8000 75,7 bulk 

B.871220 M20 12 417 340 32,0 27,0 12000 131,7 bulk 

B.871422 ! M22 14 501 410 36,0 30,0 14000 334,6 bulk 

B.871624 ! M24 16 598 463 41,0 32,0 23000 497,1 bulk 

Note : All break loads are determined by thread and wedges ( jaws ). 



Spelter Socket - Fork 


Structural 

Art.no. L1 L2 L3 L4 L5 D1 D2 B.L. 


B.R842819 19 258 121 55,0 37,0 30,0 28,0 70 25500 327 bulk 

B.R843222 22 309 145 67,0 43,0 35,0 32,0 80 31000 485 bulk 

B.R843526 26 366 154 72,0 46,0 35,0 35,0 85 43000 685 bulk 

B.R844832 32 435 205 93,0 56,0 44,0 48,0 110 76000 1405 bulk 

Note : All break loads are determined by clevis pin. 

ONLY ON REQUEST 


Wall Toggle Terminal Aisi 316 

Art.no. L1 L2 L3 L4 D1 D2 B.L. 

wire Φ kg Kg/100 pack iod 

B.191503 3,0 3,5 74 38,0 40,0 14,0 6,4 6,4 1250 4,0 bulk 

B.191504 4,0 4,4 87 45,0 44,0 18,0 8,3 7,5 2350 6,5 bulk

Toggle Terminal Aisi 316 


Structural 

Art.no. D1 D2 D3 L1 L2 A B C B.L. 


B.500603 3,0 3,5 6,35 6,35 81 38 10 16 12,8 1300 4,3 10 

B.500804 4,0 4,4 7,50 8,0 94 45 11 19 15,0 2350 7,3 10 

B.509505 5,0 5,3 9,00 9,5 116 51 13 25 20,3 3500 13,8 10 

B.501106 X 6,0 6,5 12,58 11,0 135 64 15 25 19,5 4100 27,3 10 

B.501206 X 6,0 6,5 12,58 12,7 151 64 18 31 24,7 6200 33,4 5 

B.501207 X 7,0 7,5 14,20 12,7 157 70 18 31 24,7 6200 35,7 5 

B.501308 8,0 8,4 16,00 12,7 170 83 18 31 24,7 6200 37,5 5 

B.501608 X 8,0 8,4 16,00 15,9 198 83 20 37 29,0 9800 59,7 5 

B.501610 10,0 10,5 17,80 15,9 192 89 20 37 29,0 9800 64,3 5 

B.501910 X 10,0 10,5 17,80 19,0 228 100 24 42 32,5 13000 100,0 bulk 

B.501912 X 12,0 12,5 21,40 19,0 240 120 24 42 32,5 13000 103,0 bulk 

B.502214 14,0 14,8 25,00 22,0 277 140 26 46 34,9 17000 170,2 bulk 

B.502516 16,0 17,0 28,00 25,4 313 160 29 53 40,3 24000 265,5 bulk 

B.502819 19,0 20,0 34,50 28,0 399 200 34 60 46,5 25500 612,0 bulk 

B.503222 22,0 23,5 40,40 32,0 463 230 40 70 54,0 31000 570,0 bulk 

B.503526 26,0 27,5 46,00 36,0 518 280 44 80 62,0 43000 750,0 bulk

Swageless Toggle Terninal Aisi 316 


Structural 

Art.no. L1 L2 L3 A B C D B.L. 

wire kg pack iod 

B.830603 3,0 71 50 14,0 8,0 15,0 12,0 6,0 750 bulk 

B.830804 4,0 90 61 18,0 10,0 19,0 15,0 8,0 1500 bulk 

B.831005 5,0 108 75 23,0 12,0 25,5 21,0 9,5 2180 bulk 

B.831106 6,0 125 88 30,0 15,0 28,5 23,0 11,0 3700 bulk 

B.831207 7,0 140 100 30,0 18,0 31,0 24,7 12,7 4700 bulk 

B.831208 8,0 148 102 30,0 18,0 30,0 23,7 12,7 5600 bulk 

B.831610 10,0 176 125 35,0 20,0 40,0 32,0 16,0 8300 bulk 

B.831912 12,0 206 138 40,0 24,0 45,5 36,0 19,0 12000 bulk 

B.832214 14,0 230 157 50,0 26,0 46,0 35,0 22,2 17000 bulk 

B.832516 16,0 261 180 60,0 29,0 53,0 40,0 25,4 23000 bulk 



Swageless Wall Toggle Aisi 316 

Art.no. D1 D2 D3 L1 L2 B.L. Kg./ 

wire kg 100 pack iod 

B.831503 3,0 14 40 Φ6,4 64,0 43,0 700 5,8 bulk 

B.831504 4,0 18 44 Φ8,3 79,0 50,0 1500 9,2 bulk

Toggles Aisi 316 


Structural 

Art.no. L A B D B.L. Kg/ 

kg 100 pack iod 

B,140006 25,0 8 6,5 6,0 1800 2,3 10 

B.140008 30,0 9 7,5 8,0 2600 4,0 10 

B.140010 40,0 11 9,5 9,5 4000 5,9 10 

B.140011 45,0 12 10,5 11,0 4800 8,5 10 

B.140012 50,0 14 12 12,0 5800 12,4 10 

B.140016 55,0 17 15 16,0 8000 22,5 10 

B.140019 60,0 21 18 19,0 13000 40,7 10 



Toggles Aisi 316 

Art.no. AA BB D1 D2 L B.L. Kg/ 

kg 100 pack iod 

B.140506 7,0 5 5,5 5,0 25,0 1300 1,8 25 

B.140608 8,0 6 6,5 6,0 27,0 1800 3,0 10 

B.140810 10,0 8 8,5 8,0 33,0 2600 5,5 10 

B.141011 12,0 9 10 9,5 37,0 3500 7,2 10 

B.141111 15,0 9 11,5 11,0 45,0 4800 12,1 10 

B.141214 14,0 10 12,5 12,0 48,0 5800 14,5 10 

B.141616 21,0 14 14,5 14,0 62,0 7500 28,0 10 



Rigging screws welded Fork Terminal Aisi 316 

Art.no. G wire L1 L2 A D D1 B.L. 


Structural 

metric metric kg Kg/100 pack iod 

B.120204 M4 2,0 188 136 6,5 4,0 5,50 500 3,3 10 1E+05 

B.120205 M5 2,0 206 152 7,5 5,0 5,50 800 4,5 10 1E+05 

B.122505 M5 2,5 206 152 7,5 5,0 5,50 800 4,6 10 1E+05 

B.120306 M6 3,0 232 170 7,5 5,0 6,35 1250 8,5 10 1E+05 

B.120406 M6 4,0 242 180 7,5 5,0 7,50 1250 8,7 10 1E+05 

B.120408 M8 4,0 275 199 9,5 6,0 7,50 1300 13,0 10 1E+05 

B.120508 M8 5,0 281 205 9,5 6,0 9,00 1300 13,2 10 1E+05 

B.120510 M10 5,0 312 228 11 8,0 9,00 2600 22,5 10 1E+05 

B.120610 M10 6,0 327 243 11 8,0 12,58 2600 25,6 10 1E+05 

B.120612 M12 6,0 393 287 14 12,0 12,58 5100 47,5 5 1E+05 

B.120712 M12 7,0 401 295 14 12,0 14,20 5100 50,0 5 1E+05 

B.120812 M12 8,0 416 310 14 12,0 16,00 5100 53,5 5 1E+05 

B.120714 M14 7,0 439 319 14 12,0 14,20 5900 58,0 5 1E+05 

B.120814 M14 8,0 8,0 453 333 14 12,0 16,00 5900 5900 63,5 55 1E+05 1E+05 

B.120816 M16 8,0 499 366 18 14,0 16,00 8000 89,5 5 1E+05 

B.120816L M16 8,0 497 364 22 14,0 16,00 8000 89,5 5 120816L 

B.121016 M16 10,0 506 373 18 14,0 17,80 8000 93,0 5 1E+05 

B.121016L M16 10,0 504 371 22 14,0 17,80 8000 93,0 5 121016L 

B.121020 M20 10,0 587 427 24 19,0 17,80 13000 170,1 BULK 1E+05 

B.121220 M20 12,0 606 446 24 19,0 20,00 13000 170,1 BULK 1E+05 

B.121422 ! M22 14,0 736 555 30 22,0 25,00 17000 452,0 BULK 1E+05 

B.121624 ! M24 16,0 874 641 30 30 25,4 28,00 20000 662,0 BULK 1E+05 

! Body with bronze inserts 

Rigging screws machined Fork Terminal Aisi 316 

Art.no. G wire L1 L2 A D B.L. 

metric metric kg Kg/100 pack iod 

B.741220 M20 12,0 646 492 20 19,0 13000 240,0 BULK 7E+05 

B.741422 M22 14,0 720 540 22 22,0 17000 649,0 BULK 7E+05 

B.741622 M22 16,0 745 565 22 22,0 17000 670,0 BULK 7E+05 

B.741624 M24 16,0 863 630 25 25,0 20000 876,0 BULK 7E+05 

B.741927 M27 19,0 963 728 30 28,0 25500 1332,0 BULK 7E+05 

B.742230 B.742230 M30 22,0 1082 820 35 32,0 31000 31000 1888,0 BULK 7E+05 

B.742636 M36 26,0 1186 912 35 35,0 43000 2484,0 BULK 7E+05 



Welded fork terminals Aisi 316 


Structural 

Art.no. wire L1 L2 A D D1 D D1 B.L. 


B.100502 2,0 58 12 7,5 5,0 5,50 4,0 5,50 800 2,0 25 100502 

B.100525 2,5 58 12 7,5 5,0 5,50 5,0 5,50 800 2,0 25 100525 

B.100503 3,0 67 12 7,5 5,0 6,35 5,0 5,50 800 2,3 25 100503 

B.100603 3,0 68 13 9,5 6,0 6,35 5,0 6,35 1300 2,8 25 100603 

B.100504 4,0 71 12 7,5 5,0 7,50 5,0 7,50 800 2,7 25 100504 

B.100604 4,0 73 13 9,5 6,0 7,50 6,0 7,50 1300 3,4 25 100604 

B.100804 4,0 77 15 11 8,0 7,50 6,0 9,00 2350 4,9 25 100804 

B.100605 5,0 83 13 9,5 6,0 9,00 8,0 9,00 1300 4,1 25 100605 

B.100805 5,0 87 15 11 8,0 9,00 8,0 12,58 2350 5,5 10 100805 

B.109505 5,0 91 19 12 9,5 9,00 12,0 12,58 3500 7,2 10 109505 

B.100806 6,0 99 15 11 8,0 12,58 12,0 16,00 2350 10,0 10 100806 

B.109506 6,0 104 19 12 9,5 12,58 12,0 14,20 3500 11,3 10 109506 

B.101106 6,0 108 23 13 11,0 12,58 12,0 16,00 4700 13,9 10 101106 

B.101206 6,0 6,0 110 25 14 12,0 12,58 14,0 16,00 5400 5400 17,6 10 101206 

B.101207 7,0 119 25 14 12,0 14,20 14,0 17,80 5400 18,1 10 101207 

B.101208 8,0 136 25 14 12,0 16,00 14,0 17,80 5400 21,6 10 101208 

B.101608 8,0 145 33 18 16,0 16,00 19,0 17,80 9600 25,5 10 101608 

B.101410 10,0 151 33 18 14,0 17,80 22,0 25,00 7600 35,0 10 101410 

B.101410L 10,0 149 31 22 14,0 17,80 25,4 28,00 7600 36,0 10 101410L 

B.101612 12,0 174 33 18 16,0 20,00 25,4 28,00 10000 60,0 5 101612 

B.101612L 12,0 171 31 22 16,0 20,00 25,4 28,00 10000 60,0 5 101612L 

B.101912 12,0 189 52 24 19,0 20,00 25,4 28,00 28,00 13000 66,0 55 101912 

B.101912L 12,0 187 48 30 19,0 20,00 25,4 28,00 13000 66,0 5 101912L 

B.101912X 12,0 205 52 24 19,0 21,40 25,4 28,00 13000 75,0 5 101912X 

B.101914L 14,0 221 48 30 19,0 25,00 25,4 28,00 13000 75,0 5 101914L 

B.102514 14,0 235 62 30 25,0 25,00 25,4 28,00 24000 125,0 5 102514 

B.102516 16,0 264 62 30 25,0 28,00 25,4 28,00 24000 140,0 5 102516 



Machined fork terminals Aisi 316 


Structural 

Art.no. wire L1 L2 L3 A D D1 B.L. 


B.721912 12,0 197 45 105 20,0 19,00 20,0 13000 100,0 BULK 721912 

B.722214 14,0 239 49 140 22,0 22,00 25,0 17000 170,0 BULK 722214 

B.722516 16,0 271 52 160 25,0 25,40 28,0 24000 210,0 BULK 722516 

B.722819 19,0 327 55 200 30,0 28,00 34,5 25500 330,0 BULK 722819 

B.723222 22,0 377 67 230 35,0 32,00 40,4 31000 480,0 BULK 723222 

B.723526 26,0 434 67 280 35,0 35,00 46,0 43000 700,0 BULK 723526 

Eye terminals Aisi 316 

Notice: All break loads are determined by clevis pin 

Art.no. wire D1 D2 D3 L1 L2 A B.L. 


B.190002 2,0 2,2 5,50 5,5 49 32 3 800 0,9 100 190002 

B.190025 2,5 2,8 5,50 5,5 49 32 3 800 0,8 100 190025 

B.190003 3,0 3,5 6,35 6,5 58 38 4 1300 1,3 100 190003 

B.190004 4,0 4,4 7,50 8,5 67 45 5 2350 2,3 100 190004 

B.190005 5,0 5,3 9,00 10,5 79 51 6 4200 3,9 25 190005 

B.190006 6,0 6,5 12,58 13,0 94 64 8 5600 8,7 10 190006 

B.190006X 6,0 6,5 12,58 13,2 105 64 10 6200 11,2 10 190006X 

B.190007 7,0 7,5 14,20 13,0 104 70 9 5600 11,5 10 190007 

B.190007X 7,0 7,5 14,20 13,2 110 70 10 6200 13,5 10 190007X 

B.190008 8,0 8,4 16,00 14,5 124 83 10 7600 17,0 10 190008 

B.190008X 8,0 8,4 16,00 16,5 141 83 12 9800 23,5 10 190008X 

B.190010 10,0 10,5 17,80 16,3 137 89 11 9800 25,0 10 190010 

B.190010X 10,0 10,5 17,80 19,5 165 100 16 13000 38,0 10 190010X 

B.190012 12,0 12,5 20,00 19,3 156 105 15 13000 41,5 5 190012 

B.190012X 12,0 12,5 21,40 19,3 178 120 15 13000 41,0 5 190012X 

B.190014 14,0 14,8 25,00 23,0 206 140 18 17000 75,6 5 190014 

B.190016 16,0 17,0 28,00 26,0 232 160 20 24000 102,0 5 190016 

B.190019 19,0 20,0 34,50 28,5 302 200 25 27000 209,0 BULK 190019 

B.190022 22,0 23,5 40,40 33,0 348 230 30 31000 314,0 BULK 190022 

B.190026 B.190026 26,0 27,5 46,00 36,0 36,0 400 280 30 43000 425,0 BULK 190026 190026 

Notice: All break loads are determined by eye (D3) 

Note : The user is responsible for choosing the proper cable diameter and for correct assembly.

Domehead Terminals Aisi 316 

Art.no. wire Φ L1 L2 L3 A1 D1 


Structural 

metric PIN Kg/100 pack iod 

B.660003 3,0 3,5 52,0 48,5 38,0 6,35 10,0 1,1 20 660003 

B.660004 4,0 4,4 59,0 55,5 45,0 7,50 11,5 2,4 20 660004 

B.660005 5,0 5,3 66,5 62,5 51,0 9,00 14,0 3,8 20 660005 

B.660006 6,0 6,5 79,0 74 64,0 12,58 18,0 7,9 20 660006 

Inside Thread Terminals Aisi 316 

Art.no. GG Wire L1 L2 L3 L4 D1 D1 D2 D2 A B.L. 

Right metric metric Kg. Kg/100 iod 

B.982504 M4 2,5 64,0 32 15 25 5,50 5,50 2,8 500 0,8 982504 

B.980305 M5 3,0 77,0 38 20 30 6,35 7,13 3,5 800 1,3 980305 

B.980305L M5 3,0 92,0 38 35 45 6,35 7,13 3,5 800 1,6 980305L 

B.980406 M6 4,0 84,0 45 20 30 7,50 8,00 4,4 1250 1,8 980406 

B.980406L M6 4,0 99,0 45 35 45 7,50 8,00 4,4 1250 2,1 980406L 

B.980506 M6 5,0 90,0 51 20 30 9,00 9,00 5,3 1250 2,8 980506 

B.980506L M6 5,0 105,0 51 51 35 35 45 45 9,00 9,00 5,3 1250 3,2 980506L 980506L 

B.980508 M8 5,0 112,0 51 40 53 9,00 12,58 5,3 2350 5,4 980508 

B.980608 M8 6,0 110,0 64 25 35 12,58 12,58 6,5 2350 7,2 980608 

B.980608L M8 6,0 126,0 64 40 50 12,58 12,58 6,5 2350 8,2 980608L 

B.980610 M10 6,0 127,0 64 40 53 12,58 16,00 6,5 3500 10,5 980610 

B.980810 M10 8,0 140,0 83 40 50 16,00 16,00 8,4 3500 15,4 980810 

B.980812 M12 8,0 147,0 83 40 53 16,00 18,00 8,4 5100 16,7 980812 

B.981012 M12 10,0 150,0 89 40 50 17,80 17,80 10,5 5100 19,4 981012 

B.981016 M16 10,0 152,0 89 40 53 17,80 22,00 10,5 8000 20,7 981016 

Art.no. 

Left iod 

B.992504 992504 

B.990305 990305 

B.990305L 990305L 

B.990406 990406 

B.990406L 990406L 

B.990506 990506 

B.990506L 990506L 

B.990508 990508 

B.990608 990608 

B.990608L 990608L 

B.990610 990610 

B.990810 

B.990812 

B.991012 

Note; The user is responsible for choosing the proper cable 

diameter and for correct assembly. 

990810 

990812 

991012 

B.991016 991016

Thread Terminals Aisi 316 


Structural 

Art.no. G Wire L1 L2 L3 D A NV B.L. 

Right metric Metric kg Kg/100 pack iod 

B.900205 M5 2,0 87 32 42 5,5 2,2 4,5 800 1,4 BULK 900205 

B.902505 M5 2,5 87 32 42 5,5 2,8 4,5 800 1,5 BULK 902505 

B.900306 M6 3,0 100 38 48 6,4 3,5 5,0 1250 2,0 BULK 900306 

B.900406 M6 4,0 110 45 48 7,5 4,4 6,0 1250 2,4 BULK 900406 

B.900408 M8 4,0 117 45 57 7,5 4,4 6,0 2350 30,0 BULK 900408 

B.900508 M8 5,0 123 51 57 9,0 5,3 7,0 2350 4,0 BULK 900508 

B.900510 M10 5,0 130 51 63 9,0 5,3 7,0 3500 4,5 BULK 900510 

B.900610 M10 6,0 145 64 63 12,6 6,5 11,0 3500 8,4 BULK 900610 

B.900612 M12 6,0 162 64 80 12,6 6,5 11,0 5100 11,0 BULK 900612 

B.900712 M12 7,0 170 70 80 14,2 7,5 12,0 5100 13,3 BULK 900712 

B.900714 M14 7,0 180 70 89 14,2 7,5 12,0 5900 16,0 BULK 900714 

B.900812 M12 8,0 185 83 80 16,0 8,4 14,0 5100 19,2 BULK 900812 

B.900814 M14 8,0 194 83 89 16,0 8,4 14,0 5900 20,0 BULK 900814 

B.900816 M16 8,0 203 83 100 16,0 8,4 14,0 8000 23,0 BULK 900816 

B.901016 M16 10,0 210 89 100 17,8 10,5 15,0 8000 35,0 BULK 901016 

B.901020 M20 10,0 230 230 89 120 17,8 17,8 10,5 10,5 15,0 15,0 13000 35,0 35,0 BULK 901020 

B.901220 M20 12,0 249 105 120 20,0 12,5 17,0 13000 45,0 BULK 901220 

B.901220X M20 12,0 265 120 120 21,4 12,5 19,0 13000 50,0 BULK 901220X 

B.901422 M22 14,0 308 140 140 25,0 14,8 22,0 17000 76,8 BULK 901422 

B.901622 M22 16,0 333 160 140 28,0 17,0 25,0 17000 97,8 BULK 901622 

B.901624 M24 16,0 363 160 170 28,0 17,0 25,0 23000 111,0 BULK 901624 

B.901927 M27 19,0 425 200 180 34,5 20,0 30,0 25500 209,0 BULK 901927 

B.902230 M30 22,0 480 230 200 40,5 23,5 36,0 31000 314,0 BULK 902230 

B.902636 M36 26,0 550 280 220 46,0 27,5 41,0 43000 470,0 BULK 902636 

Art.no. 

Left iod 

B.910205 910205 

B.912505 912505 

B.910306 910306 

B.910406 910406 

B.910408 910408 

B.910508 910508 

B.910510 910510 

B.910610 910610 

B.910612 910612 

B.910712 910712 

B.910714 910714 

B.910812 910812 

B.910814 910814 

B.910816 910816 910816 

B.911016 911016 

B.911020 911020 

B.911220 911220 

B.911220X 911220X 

B.911422 911422 

B.911622 

B.911624 

B.911927 

B.912230 


The user is responsible for choosing the proper cable 

diameter and for correct assembly. 

911622 

911624 

911927 

912230 

B.912636 912636


Structural 

Thread Eyes Aisi 316 

Art.no. G D1 D2 L1 L2 B B.L. 

Right metric kg Kg/100 pack iod 

B.021904 M4 4,3 10,0 50,0 35,0 3,0 500 0,5 25 021904 

B.021905 M5 5,5 12,0 63,0 41,0 3,0 800 0,9 25 021905 

B.021906 M6 6,5 14,0 65,0 47,0 4,0 1250 1,5 25 021906 

B.021908 M8 8,5 17,0 78,0 57,0 5,0 2000 3,1 25 021908 

B.021910 M10 10,5 22,0 90,0 63,0 6,0 3500 5,1 25 021910 

B.021912 M12 13,0 25,0 110,0 80,0 8,0 5100 10,1 10 021912 

B.021914 M14 13,0 28,0 124,0 90,0 9,0 5900 14,1 10 021914 

B.021916 M16 14,5 31,0 133,0 100,0 10,0 8000 20,4 10 021916 

B.021920 M20 19,5 40,0 164,0 120,0 15,0 13000 40,6 5 021920 

B.021922X M22 23,0 46,0 196,0 140,0 18,0 17000 69,0 BULK 021922X 

B.021924X M24 26,0 53,0 230,0 170,0 20,0 20000 105,0 BULK 021924X 

B.021927X M27 28,5 65,0 247,0 180,0 25,0 25500 153,0 BULK 021927X 

B.021930X M30 33,0 70,0 274,0 200,0 30,0 31000 204,0 BULK 021930X 

B.021936X 

Art.no. 

M36 36,0 80,0 295,0 220,0 30,0 43000 296,0 BULK 021936X 

Left iod iod 

B.031904 031904 

B.031905 031905 

B.031906 031906 

B.031908 031908 

B.031910 031910 

B.031912 031912 

B.031914 031914 

B.031916 031916 

B.031920 031920 

B.031922X 031922X 

B.031924X 031924X 

B.031927X 031927X 

B.031930X 031930X 

B.031936X 031936X 

Note : All break loads are determined by eye D1 and thread. 


diameter and for correct assembly.


Structural 

Bodies Aisi 316 

Art.no. G L1 D1 KW B.L. 


B.011204 M4 70,0 7,0 - 500 1,2 100 011204 

B.011205 M5 80,0 8,0 - 800 1,2 100 011205 

B.011206 M6 92,0 10,0 - 1300 2,6 100 011206 

B.011208 M8 112,0 13,5 - 2600 6,0 50 011208 

B.011210 M10 120,0 17,2 - 3500 9,4 BULK 011210 

B.011212 M12 150,0 21,3 - 5400 16,0 BULK 011212 

B.011214 M14 170,0 21,3 - 5900 18,4 BULK 011214 

B.011216 M16 190,0 26,9 - 8000 27,2 BULK 011216 

B.011220 M20 220,0 33,7 - 13000 46,8 BULK 011220 

B.012320 M20 240,0 40,0 36,0 13000 158,2 BULK 012320 

B.012322 M22 270,0 45,0 41,0 17000 161,6 BULK 012322 

B.012324 M24 325,0 50,0 46,0 20000 312,6 BULK 012324 

B.012327 M27 345,0 55,0 50,0 25500 408,1 BULK 012327 

B.012330 M30 375,0 60,0 55,0 31000 538,4 BULK 012330 

B.012336 M36 410,0 65,0 60,0 43000 602,8 BULK 012336 


Machined Thread Forks Aisi 316 

Art.no. G L1 L2 L3 A D B.L. 

Right metric Pin kg Kg/100 pack iod 

B.027420B M20 219,0 45,0 125,0 20,0 19,0 13000 125,0 BULK 027420B 

B.027422B M22 216,0 49,0 140,0 22,0 22,0 17000 300,0 BULK 027422B 

B.027424B M24 255,0 52,0 170,0 25,0 25,0 20000 400,0 BULK 027424B 

B.027427B M27 274,0 55,0 180,0 30,0 28,0 25500 640,0 BULK 027427B 

B.027430B M30 316,0 67,0 200,0 35,0 32,0 31000 980,0 BULK 027430B 

B.027436B 

Art.no. 

M36 334,0 67,0 220,0 35,0 35,0 43000 1300,0 BULK 027436B 

Left iod 

B.037420B 037420B 

B.037422B 037422B 

B.037424B 037424B 

B.037427B 037427B 

B.037430B 037430B 

B.037436B 037436B 





Structural 

Welded Thread Forks Aisi 316 

Art.no. G A D L1 L2 L3 B.L. 

Right metric Pin kg Kg/100 pack iod 

B.021204B M4 6,5 4,0 50,0 9,5 34,0 500 021204B 

B.021205B M5 7,5 5,0 60,0 12,0 41,0 800 021205B 

B.021206B M6 7,5 5,0 67,0 12,0 47,0 1000 021206B 

B.021206XB M6 9,5 6,0 68,0 13,0 47,0 1300 021206XB 

B.021208B M8 9,5 6,0 79,0 13,0 57,0 1300 021208B 

B.021208XB M8 11,0 8,0 82,0 15,0 57,0 2350 021208XB 

B.021210B M10 11,0 8,0 90,0 15,0 63,0 2600 021210B 

B.021210XB M10 12,0 9,5 94,0 19,0 63,0 3500 021210XB 

B.021212B M12 14,0 12,0 119,0 25,0 80,0 5100 021212B 

B.021212XB M12 18,0 14,0 129,0 33,0 80,0 5100 021212XB 

B.021214B M14 14,0 12,0 137,0 25,0 90,0 5100 021214B 

B.021216B M16 18,0 14,0 151,0 33,0 100,0 8000 021216B 

B.021220B M20 24,0 19,0 191,0 50,5 120,0 13000 021220B 

B.021222B M22 30,0 22,0 224,0 57,5 140,0 17000 021222B 

B.021224B 

Art.no. 

M24 30,0 25,4 258,0 62,5 170,0 20000 021224B 

Left iod 

B.031204B 031204B 

B.031205B 031205B 

B.031206B 031206B 

B.031206XB 031206XB 

B.031208B 031208B 

B.031208XB 031208XB 

B.031210B 031210B 

B.031210XB 031210XB 

B.031212B 031212B 

B.031212XB 031212XB 

B.031214B 031214B 

B.031216B 031216B 

B.031220B 031220B 

B.031222B 031222B 

B.031224B 031224B 


Note : The user is responsible for choosing the proper cable 



Structural 

Swageless Eye Terminals Aisi 316 

Art.no. WIRE A L1 L2 L3 D2 KW KW1 B.L. 


B.821903 3,0 5,5 50,0 58,0 26,5 6,3 10,0 12,0 750 4,0 BULK 821903 

B.821904 4,0 7,0 58,0 68,0 31,0 8,3 13,0 14,0 1500 7,3 BULK 821904 

B.821905 5,0 8,0 70,0 81,0 37,0 10,3 14,0 16,0 2180 9,8 BULK 821905 

B.821906 6,0 9,0 83,0 97,0 45,0 12,3 17,0 19,0 3700 15,0 BULK 821906 

B.821907 7,0 9,0 89,0 105,0 50,5 12,3 18,0 21,0 4700 21,2 BULK 821907 

B.821908 8,0 10,0 103,0 121,0 52,5 14,3 19,0 24,0 5600 28,1 BULK 821908 

B.821910 10,0 13,0 116,0 135,0 65,0 16,3 24,0 27,0 8300 46,0 BULK 821910 

B.821912 12,0 15,0 137,0 160,0 71,5 19,5 27,0 32,0 12000 72,0 BULK 821912 

B.821914 14,0 18,0 160,0 185,0 85,0 22,0 30,0 36,0 14000 110,0 BULK 821914 

B.821916 16,0 20,0 170,0 197,0 98,0 25,0 32,0 41,0 23000 160,0 BULK 821916 

Note : All break loads are determined by wedges ( jaws ) and eye ( D2 ). 

Swageless Fork Terminals Aisi 316 

Art.no. A L1 L2 L3 L4 WIRE D2 KW KW1 B.L. KG/ 

kg Kg 100 iod 

B.840603 6,0 6,0 55,0 63,0 63,0 8,0 8,0 29,0 3,0 6,0 14,0 12 750 5,5 840603 

B.840804 8,0 62,0 73,0 8,0 35,0 4,0 8,0 19,0 14 1500 7,3 840804 

B.841005 10,0 72,0 83,0 10,0 42,0 5,0 10,0 22,0 16 2180 15 841005 

B.841206 12,0 82,0 95,0 12,0 47,5 6,0 12,0 27,0 19 3700 23 841206 

B.841207 12,0 102,0 115,0 13,0 54,5 7,0 12,0 29,0 21 4700 29 841207 

B.841408 14,0 103,0 118,0 14,0 58,0 8,0 14,0 30,0 24 5600 38 841408 

B.841610 16,0 117,0 135,0 16,0 70,0 10,0 16,0 36,0 27 8300 63 841610 

B.841912 18,0 142,0 162,0 16,0 75,0 12,0 19,0 42,0 32 12000 97 841912 

B.842214 21,0 162,0 191,0 19,0 88,0 14,0 22,0 46,0 36 14000 135 

B.842516 23,0 184,0 217,0 22,0 102,0 16,0 25,0 55,0 41 23000 215 

Note : All break loads are determined by wedges ( jaws ) and clevis pin. 


PAGE54 

Structural 

Swageless Thread Terminals Aisi 316 

Art.no. G wire L1 L2 L3 KW KW1 B.L. 


B.800305 M5 3,0 79,0 58,0 42,0 10,0 12,0 750 4,2 BULK 800305 

B.800306 M6 3,0 85,0 63,0 47,0 10,0 12,0 750 4,5 BULK 800306 

B.800406 M6 4,0 92,0 63,0 47,0 12,0 14,0 1500 5,6 BULK 800406 

B.800408 M8 4,0 102,0 72,0 57,0 12,0 14,0 1500 6,6 BULK 800408 

B.800508 M8 5,0 111,0 78,0 57,0 13,0 16,0 2180 9,0 BULK 800508 

B.800510 M10 5,0 117,0 84,0 63,0 13,0 16,0 2180 10,0 BULK 800510 

B.800610 M10 6,0 128,0 90,0 63,0 16,0 19,0 3700 15,0 BULK 800610 

B.800612 M12 6,0 145,0 107,0 80,0 16,0 19,0 3700 17,0 BULK 800612 

B.800712 M12 7,0 153,0 110,0 80,0 18,0 21,0 4700 22,0 BULK 800712 

B.800714 M14 7,0 162,0 119,0 89,0 18,0 21,0 4700 25,0 BULK 800714 

B.800812 M12 8,0 162,0 113,0 80,0 19,0 24,0 5600 28,0 BULK 800812 

B.800814 M14 8,0 171,0 122,0 89,0 19,0 24,0 5600 31,0 BULK 800814 

B.800816 M16 8,0 182,0 133,0 100,0 19,0 24,0 5600 40,0 BULK 800816 

B.801016 M16 10,0 190,0 139,0 100,0 24,0 27,0 8300 48,0 BULK 801016 

B.801220 M20 12,0 227,0 159,0 120,0 27,0 32,0 12000 79,0 BULK 801220 

B.801422 M22 14,0 264,0 191,0 140,0 30,0 36,0 14000 124,0 BULK 801422 

B.801624 

Art.no. 

M24 16,0 308,0 227,0 170,0 32,0 41,0 23000 175,0 BULK 801624 

Left iod 

B.810305 810305 

B.810306 810306 

B.810406 810406 

B.810408 810408 

B.810508 810508 

B.810510 810510 

B.810610 810610 

B.810612 810612 

B.810712 810712 

B.810714 810714 

B.810812 810812 

B.810814 810814 

B.810816 810816 

B.811016 811016 

B.811220 811220 

B.811422 811422 

B.811624 811624 

Note : All break loads are determined by wedges ( jaws ) and thread. 



Structural 

Adjuster Fork Aisi 316 

Art.no. G A D1 D2 L1 L2 L3 L4 B.L. 


C700606 M6 6,00 6,0 14,0 43,0 20,0 35,0 9,0 1300 3,7 BULK 

C700808 M8 7,00 8,0 18,0 54,0 25,5 43,5 11,0 2500 7,7 BULK 

C701010 M10 8,00 10,0 22,0 66,0 31,0 53,0 13,0 3500 14,6 BULK 

C701212 M12 10,00 12,0 26,0 78,0 37,0 63,0 16,0 5400 22,8 BULK 

C701616 M16 12,00 16,0 34,0 100,0 46,5 80,5 19,0 8000 51,5 BULK 

C702020 M20 15,00 20,0 42,0 122,0 57,5 98,0 23,5 13000 95,6 BULK 

C702224 M24 18,00 22,0 52,0 150,0 72,0 120,0 31,0 22000 178,6 BULK 

Art.no. L5 NV H 

Left 

C710606 26,0 10,0 5,0 

C710808 32,0 13,0 6,5 

C711010 39,0 16,0 8,0 

C711212 46,0 18,0 10,0 

C711616 59,0 24,0 13,0 

C712020 72,0 30,0 16,0 

C712224 87,0 41,0 19,0 

Note : All break loads are determined by clevis pin 

( Fork ) and thread.

front page.xlsx - Qatar Steel Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?