DTM Gloss - Frazee Paint

DTM Gloss
Interior/Exterior Industrial Maintenance Acrylic Gloss Paint 540
DESCRIPTION & INTENDED USE
DTM Gloss is an industrial maintenance (high
performance) interior/exterior acrylic gloss paint
formulated to provide a durable finish when applied to
properly prepared and primed, new or previously
painted drywall, wood, masonry, and metal surfaces.
DTM Gloss has outstanding corrosion resistance,
excellent adhesion, and features easy application and
fast dry. For Professional Use Only.
FEATURES
Corrosion resistant
Excellent adhesion
For ferrous and non-ferrous metal surfaces
Easy application
Quick drying & recoat
Easy water & soap cleanup
Not manufactured with lead, mercury or chromate
containing materials
Does not contain crystalline silica or ethylene glycol
SYSTEM RECOMMENDATIONS
DRYWALL / PLASTER
1 coat: C152 UltraTech Latex Primer/Sealer
2 coats: 540 DTM Gloss
CMU (Concrete Block / Cinder Block)
1 coat: C302 UltraTech 100% Acrylic Block Filler
2 coats: 540 DTM Gloss
MASONRY
1 coat: C251 Flex Lox Acrylic-Epoxy Masonry Primer/Sealer
2 coats: 540 DTM Gloss
WOOD / SYNTHETIC WOOD
1 coat: C312 UltraTech Int/Ext 100% Acrylic Wood Primer
2 coats: 540 DTM Gloss
FERROUS METAL / NON-FERROUS METAL
2 coats: 540 DTM Gloss*
*Note: This direct-to-metal product has excellent adhesion to
bare, clean metal, but test a small area prior to application to
ensure proper adhesion to the metal substrate. For optimum
corrosion protection, apply 1-2 coats of UltraTech C309
Universal WB Metal Primer over bare ferrous metal.
PRODUCT SPECIFICATIONS
Resin Type 100% Acrylic
Finish Gloss: > 70 @ 60°
Maximum VOC Content 100 g/L (0.83 lbs/gal)
Solids
by Weight 49% ± 2%
by Volume 38% ± 2%
Coverage 300-400 sq. ft./gallon
Drying Time @ 77°F (25°C) & 50% RH
to Touch 2 hours
to Recoat 8 hours
NOTE: Drying times listed may vary depending on temperature,
humidity, film build, color, and air movement.
Weight Per Gallon 10.0 lbs
Wet Film Thickness (WFT) 4.0 mils
Dry Film Thickness (DFT) 1.5mils
Tint Bases White, Medium, Deep, Accent & Neutral
CONFORMANCE (as of 01/01/12)
EPA Yes LEED® 2009 NC Yes
OTC Yes LEED® 2009 CI Yes
CARB Yes LEED® 2009 CS Yes
SCAQMD Yes LEED® 2009 Healthcare Yes
CALGreen Code Yes NGBS Yes
APPLICATION
Use a nylon/polyester brush.
Use a 1/4" to 1/2" nap roller cover, depending on
surface texture.
Use a tip size from .015" to .019".
Stir thoroughly before and during use.
Do not apply when surface or air temperature is
below 50°F (10°C).
Apply coating evenly while maintaining a wet edge
to prevent lapping.
continued on back
DTM Gloss Interior/Exterior Industrial Maintenance Acrylic Gloss Paint 540

DTM Gloss Interior/Exterior Industrial Maintenance Acrylic Gloss Paint 540
DTM Gloss
Interior/Exterior Industrial Maintenance Acrylic Gloss Paint 540
SURFACE PREPARATION
General Surface Preparation: All surfaces must be clean, dry,
sound, and free from contaminants such as loose and peeling
paint, dirt, dust, grease, oil, wax, concrete curing agents and
bond breakers, efflorescence, rust, and chalk. Mold and
mildew must be treated and any residues removed. Dull any
glossy surfaces, repair damaged areas with appropriate
patching material, and allow to dry. Prime all new surfaces and
repaired areas with an appropriate primer.
Substrate Specific:
Drywall / Plaster
Allow new drywall and plaster finishes to properly cure
before application of primer and finish coats.
Masonry
Allow new masonry surfaces to cure before application of
primer and finish coats.
Power-wash all tilt-up and poured-in-place concrete to
remove any bond-breakers or other construction residue.
Wood / Synthetic Wood
Two coats of stain-blocking wood primer may be necessary
on lumber subject to tannin bleed, such as, redwood and
cedar.
Ferrous Metal
Minimum surface preparation for all ferrous metals is Hand
Tool Cleaning per SSPC-SP2. Remove all oil and grease from
the surface per SSPC-SP1. For optimum performance, use
Commercial Blast Cleaning per SSPC-SP6. Sandblasted or
newly cleaned metal must be primed the same day.
Non-Ferrous Metal
Allow galvanized metal to weather a minimum of six
months prior to coating. Solvent clean per SSPC-SP1. If
weathering is not feasible, or if the surface has been treated
with chromates or silicates, first solvent clean per SSPC-SP1,
then check adhesion of the primer by applying a test patch.
Allow primer to dry at least one week before testing
adhesion. If adhesion is poor, brush blasting per SSPC-SP7 is
necessary to remove these treatments.
Rusty galvanizing requires a minimum of Hand Tool
Cleaning per SSPC-SP2, then primed the same day.
Galvanized steel and aluminum should be solvent cleaned in
accordance with SSPC-SP1 and then etched either
chemically or via light blast cleaning with non-metallic
abrasive.
WARNING! If you scrape, sand, or remove old paint, you may
release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST
CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD
ALSO AVOID EXPOSURE. Wear a NIOSH approved respirator
to control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National
Lead Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead.
THINNING & CLEANUP
This product is designed to be used at package consistency.
Do not thin. Clean tools, equipment, and work area with
warm, soapy water.
STORAGE & DISPOSAL
Protect during storage from freezing and temperatures above
95°F. Consult your local city or environmental regulatory agency
for guidance on disposal options. Do not pour down a drain or
storm sewer.
LIMITATIONS
Do not use on floors.
Wait after 30 days or when paint has fully cured before cleaning
the surface with non-abrasive, mild detergent solution and
cellulose sponge.
High humidity and/or cooler temperatures will prolong dry time
of this product. Do not expose to moisture or extreme
temperature change for at least 48 hours after painting. Avoid
frost, fog and damp conditions.
CAUTIONS
WARNING!
HARMFUL IF SWALLOWED
IMPORTANT! Spray mist of any material may be hazardous. Spray
equipment must be in good condition and used with care in
accordance with manufacturer’s instructions. The use of an
appropriate respirator, eye protection and protective clothing is
recommended. Close container after use.
FIRST AID: If you experience difficulty in breathing, leave the area
to obtain fresh air. If continued difficulty is experienced, get
medical assistance immediately. In case of eye contact, flush
immediately with plenty of water for at least 15 minutes and get
medical attention, for skin, wash thoroughly with soap and water.
If swallowed, do not induce vomiting. Get medical attention
immediately. In case of spillage, absorb with inert material and
dispose of in accordance with applicable regulations.
KEEP OUT OF REACH OF CHILDREN
KEEP FROM FREEZING
SEE MATERIAL SAFETY DATA SHEET
For Chemical Emergency ONLY (spill, leak, fire, exposure or
accident), call ChemTrec at 1-800-424-9300.
WARRANTY
Frazee warrants that at the time of sale this product conforms
with applicable Frazee specifications and is free of manufacturing
defects. Frazee’s sole liability for products proven defective, and
Purchaser’s sole remedy, if any, shall be replacement of the
product or refund of the purchase price paid, at the sole option of
Frazee. This warranty is not transferable. TO THE MAXIMUM
EXTENT PERMITTED BY APPLICABLE LAW, FRAZEE MAKES NO
OTHER WARRANTIES, GUARANTEES, OR REPRESENTATIONS
OF ANY KIND, EITHER EXPRESS OR IMPLIED, OR BY USAGE OF
TRADE, AND HEREBY EXPRESSLY EXCLUDES AND DISCLAIMS
ALL IMPLIED WARRANTIES, OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL
KWAL BE LIABLE FOR PUNITIVE, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES OF ANY KIND.
Some states do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitation may not apply
to you. This Limited Warranty gives you specific legal rights and
you may have other rights which vary from State to State.
Frazee Industries, Inc.
6625 Miramar Road
San Diego, CA 92121
Information Phone: 1-800-477-9991
08/2012
The information provided on this product data sheet (“Information”) is correct to the best of our knowledge, information, and belief at the date of its publication. The Information given is designed only as a general
guide and is not to be considered as a warranty or quality specification. The Information is subject to change without prior notice. Consult your sales representative to obtain the most recent product data sheet.