New FLOWX3 F3.10 MINIFLOW Paddlewheel Flow ... - FIP FLSNET

New FLOWX3 F3.10 MINIFLOW Paddlewheel Flow Sensors
11
Technical Data
The simple and reliable paddlewheel technology has been moved into this new
MINIFLOW sensor type F3.10, designed for use with every kind of solid-free liquids.
The sensor can measure flow from 0.25 m/s producing a frequency output signal
highly repeatable. A rugged construction and a proven technology guarantee
exceptional performances with little or no maintenance required. The very small
dimension and a special design make it suitable for installation on FIP standard Teefittings
up to DN50 (1.5 in.).
Main features
General
Pipe Size Range: DN15 to DN50 (0.5 to 1.5
in.).
Flow Rate Range: 0.25 to 4 m/s (0.8 to 12.5
ft./s)
Linearity: ± 1 % of full scale
Repeatability: ± 0.5 % of full scale
Working Pressure:
- 10 bar (145 psi) @ 20°C (68°F)
- 2 bar (30 psi) @ 70°C (158°F)
Enclosure: IP68
Wetted Materials:
Sensor Body: ABS (PVDF on request)
O-rings: EPDM or FPM
Rotor: ABS (PVDF on request)
Shaft: AISI 316L
Installation Fittings
• IP 68 enclosure
• ABS body with EPDM or FPM seal
• ABS 4-blade paddlewheel (no bearings)
• Mono-directional design
• Installation on standard FIP tees
Type Description
FIP Standard
Plastic Tees
Size: D20
to D50 (0.5”
to 1.5”)
Electric
Supply voltage: 5 to 24 VDC regulated
Supply current: < 30 mA @ 24 VDC
Output signal: square wave
Output frequency: 15 Hz per m/s nominal (4.6
Hz per ft/s nominal)
Output type: transistor NPN open collector
Output current: 10 mA max.
Cable length: 2 m (6.6 ft) standard, 300 m (990
ft) maximum
Standards & Approvals
Manufactured under ISO 9001
Manufactured under ISO 14000
(Environmental Management)
CE
F.I.P. Formatura Iniezione Polimeri S.p.A.
Loc. Pian di Parata, 16015 Casella (GE) – Italy
Tel +39 010 96211 – Fax +39 010 9621209
www.flsnet.it
Dimensions

New FLOWX3 F9.51 Batch Controller
Up to 10 different batch volumes easily stored
11
The new F9.51 Batch Controller is design to improve the accuracy of liquid
batching operations. The instrument always combines complex control
capability with easy calibration and operation. A completely new development
allows the customer to store up to 10 different batch parameters.
With F9.51 is now possible to batch different volumes and different
liquids in the same pipeline with the same accuracy and just using
paddlewheel insertion flow sensors!
The new programming solutions are able to reduce and simplify the autocalibration
operation and the setting of different batch volumes.
FLOWX3 F9.51 is now one of the best cost effective solution for batching
liquids.
Up to 10 different K-factors auto-calculated and stored
The 10 different batch volumes can be set and
stored with the instrument in Batch-View Mode.
After the first setting it is enough choosing the batch
number (from 1 to 10) to get the instrument dosing
the desired liquid volume with the calibration factor
(k-factor) specifically calculated.
For every different batch operation the best
accuracy!
F.I.P. Formatura Iniezione Polimeri S.p.A.
Loc. Pian di Parata, 16015 Casella (GE) – Italy
Tel +39 010 96211 – Fax +39 010 9621209
www.flsnet.it
The standard Auto-calibration function included in
all FLS flow monitors and batch controllers has
been slightly improved.
The new F9.51 can automatically calculate and
store the calibration factor related to each different
batch volume.
Every time a different batch operation is chosen,
the associated K-factor will be automatically used
by the F9.51 to guarantee the highest accuracy.

FLOWX3 Flow Monitor - NEW GENERATION
New ASEC software design
Flowmeter performances are related to many different features, sensor technology is one of the
most important. The quality of the measure and mainly the linearity is affected by technical
construction of the sensing device.
The more the ratio between the real value and the measured value is constant the higher is the
linearity of the device. A lack of linearity reduces significantly the accuracy of the measurement
system.
Our ASEC (Auto Systematic Error Compensation) project has been developed to
study the systematic error of paddlewheel flow sensors and to offer advanced
solutions increasing linearity and accuracy of our FLOWX3 measuring system.
All flow monitors and batch controllers will be
equipped with the new ASEC design to
increase accuracy and reliability of our
paddlewheel insertion technology.
On site calibration is offered to maximize
potentialities of the new system.
Nothing to be done by the customer: install
and calibrate your new FLS system as you
have always done and…appreciate last
developments and new performances
Available on all F9.0X and F9.5X models
starting from July 1, 2006 (in conjunction with
F3.00.H flow sensors only).
No extra price for new ASEC flow monitors.
Try the difference!
Accuracy = 0,75% of F.S.
F.I.P. Formatura Iniezione Polimeri S.p.A.
Loc. Pian di Parata, 16015 Casella (GE) – Italy
Tel +39 010 96211 – Fax +39 010 9621209
www.flsnet.it
Freq. Output
&
4-20mA Output
Accuracy = 2% of reading + 0,2 cm/s

FLOWX3 Flow Monitor - NEW GENERATION
New BACKLIT display
Starting from NOW all FLOWX3 flow monitors and batch controllers are available
with BACKLIT LCD display.
No extra price during the “hot” months (June & July).
Try the difference!
F.I.P. Formatura Iniezione Polimeri S.p.A.
Loc. Pian di Parata, 16015 Casella (GE) – Italy
Tel +39 010 96211 – Fax +39 010 9621209
www.flsnet.it
The very complete set of information available on
FLOWX3 LCD in any light condition.
Very low current consumption design: monitors
continue to be filled with epoxy for a perfect water
tightness.
The option is available on F9.01, F9.02, F9.03,
F9.50 and F9.51 in panel, wall and compact
installation!
An “L” at the end of the standard Part No. is
enough to get this precious advantage.