ASN - Adlee Powertronic Co., LTD

More documents

Recommendations

Info

6. DIGITAL OPERATION PANEL LED Operating Indication PROG FUNC STOP REV FWD AS2-DSP FUNC PROG STOP Operation key Key function Description FWD RUN Forward run <strong>Co</strong>mmands forward run REV RUN Reverse run <strong>Co</strong>mmands reverse run SHIFT Cursor movement Select the digit DOWN Down Decrease the parameter value UP Up Increase the parameter value PROG Memory storage FUNC Function Model Indication Digital Indication Digital Indication Saves the setting vaule Press once to select function CDxx and press again to change its content STOP Stop Stop operation / Escape to standby mode 17 F306 FUNC CHARGE REV FWD REMOTE CONTROL STOP LED Operating Indication
Page 1: R ADLEEPOWER INSTRUCTION MANUAL GEN
Page 6 and 7: CAUTION * The control PC board empl
Page 8: 1. RECEIVING This AS series AC driv
Page 12 and 13: Fig 2 5 Unit : mm
Page 15: 5 cm 5 cm 6 cm AIR FLOW 2 6 cm 8 4
Page 19 and 20: (3) Description of Hardware setting
Page 21: (4) WIRING 4-1 Wiring of main circu
Page 27 and 28: DISPLAY CODE FUNCTION DEFAULT VALUE
Page 30: ADJUST RANGE UNIT USER SETTING 0 or
Page 33 and 34: Communication address description C
Page 35 and 36: 7-1. Function setting Before starti
Page 37 and 38: First speed setting CD00 Press key
Page 39 and 40: Jog mode CD06 0 : Normal 1 : Jog Mo
Page 41 and 42: Source operation command CD13 0 : N
Page 43 and 44: V/F pattern setting CD18 0 = Consta
Page 45 and 46: Operation Signal Acceleration time
Page 47 and 48: Frequency jump 2 CD30 Frequency jum
Page 49 and 50: The latest error record CD36 Error
Page 51 and 52: 3 - WIRE CIRCUIT CONNECTION DIAGRAM
Page 53 and 54: 5th speed setting CD47 6th speed se
Page 56 and 57: 2nd Maximum Voltage frequency CD56
Page 58 and 59: CD58=3 (S) CD58=4 (S) CD58=5 (S) CD
Page 62 and 63: Overload setting CD68 Set overload
Page 64 and 65: Communicator protocol CD78 A. Date
Page 67 and 68: CRC(Cyclical Redundancy Check) is c
Page 69: Example : Read two parameters of AC
Page 73 and 74:
Computer command message inverter a
Page 75 and 76:
D6 Computer command message AC driv
Page 77 and 78:
Computer command message AC drive r
Page 79 and 80:
2. ASCII D1 D2 D3 D4 D5 D6 Computer
Page 81 and 82:
Fault code for RS485 103 Using 03H
Page 83 and 84:
Setting sequence FUNC FUNC PROG CHA
Page 85 and 86:
Power device failure 3 PF03 Power d
Page 87 and 88:
Communication error OPE9 Over heat
Page 89 and 90:
10. TROUBLESHOOTING Display symbol
Page 91 and 92:
EXAMPLE 02 : Normal / Jog operation
Page 94:
13. Inverter Selection Inverter Cap
Page 98 and 99:
2. THREE PHASE Three phase MCCB Gro
Page 100 and 101:
MEMO
show all

ASN - Adlee Powertronic Co., LTD

Create successful ePaper yourself

Delete template?

Save as template?