Coil Handler Slings - Lift It Manufacturing
Coil Handler Slings - Lift It Manufacturing
Coil Handler Slings - Lift It Manufacturing
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>Coil</strong> <strong>Handler</strong> <strong>Slings</strong><br />
Tired of cargo damage during discharge and handling operations?<br />
Interested in decreasing discharge time and improving productivity<br />
and safety?<br />
The Perfect Combination<br />
TWIN-PATH ® EXTRA SLINGS<br />
(K-Spec ® HP Fiber and Covermax ® Tube)<br />
and<br />
CORNERMAX TM SLEEVE with DYNEEMA ® fiber<br />
Light Weight and Flexible<br />
Only 21 pounds!<br />
Decrease discharge time and injury<br />
90 minutes saved for every 90 coils handled<br />
No more wrestling heavy slings in close quarters<br />
Increase Productivity<br />
10X lighter than comparable “heavy” metal slings<br />
No need to fish hook to pull the sling through<br />
Easy to Inspect<br />
Patented Twin-Path ® Sling Inspection Systems<br />
Tattle Tails, Fiber Optics or Check Fast<br />
Warning If red yarns in the Cornermax TM Sleeve with<br />
Dyneema ® fiber are visible, DO NOT USE THE SLING.<br />
Dyneema ® is a registered trademark of Royal DSM, N.V.<br />
Order Code: CHTUFXKS 4000 X 13FT<br />
BASKET @ 90° - 80,000 LBS<br />
SLEEVE LENGTH - 8 ft.<br />
Repairable for a Fraction of the Original Cost!<br />
If the Cornermax TM Sleeve with Dyneema ® fiber is damaged, return the sling for evaluation and<br />
repair. The <strong>Coil</strong> <strong>Handler</strong> must be returned to the factory for inspection after 500 uses.<br />
WARNING WARNING WARNING WARNING<br />
The <strong>Coil</strong> <strong>Handler</strong> Sling must be returned to the factory for inspection after 500 uses.<br />
The CornerMax TM Sleeve with Dyneema ® fiber must contact the coil edges.<br />
Do Not Use:<br />
If Sling Load Carrying Yarn is visible or damaged, Tattle Tails are not visible, Fiber Optic Cable does not reflect light,<br />
External Warning Indicator is not present or Check Fast Ribbon pulls out. Do not use if red yarns are visible on the<br />
Cornermax TM Sleeve with Dyneema ® fiber. See Reverse for other important warning information.<br />
LIFT-IT ® MANUFACTURING COMPANY, INC.<br />
4780 CORONA AVENUE • LOS ANGELES, CA 90058-3808<br />
(323) 582-6076 • Fax (323) 587-1630 • E-mail: liftit@pacbell.net • www.lift-it.com
Engineered Wear Protection Devices<br />
A TUNNEL IS FORMED BETWEEN THE PAD AND LOAD EDGE<br />
Magnetic corner protectors are fabricated from a durable synthetic material that<br />
protects synthetic and wire rope slings from damage. They work on any 90º<br />
“cornered” load and keep the sling from contacting the load.<br />
Magnetic corner protectors are “protection rated” at 12,500 PSI and can be used at<br />
temperatures from -20º F ( -29º C) to 220º F ( 104º C). Heavy Duty Protectors,<br />
featuring larger diameters are also available.<br />
Magnetic Corner Protectors are also available in slotted and curved configurations.<br />
* The Slotted style (Order Code MCP-SL-9) is<br />
available in 9, 12 & 18 inch lengths.<br />
* The Slotted style is also available in a heavy<br />
duty construction<br />
(Order Code MCP-SL-9-HD)<br />
* You must specify plate thickness.<br />
* Curved Magnetic Corner Protectors are<br />
made for specific coil diameters.<br />
* You must specify the inside diameter (ID)<br />
of the coil.<br />
* Two inserts harness the inside edges, while<br />
two buffer pads are placed on the wall of the<br />
coil to deflect the sling away from the<br />
top edge.<br />
CORNERMAX TM WEAR PADS<br />
Specifications<br />
Sling Width Cornermax<br />
(Inches)<br />
TM Width<br />
(Inches)<br />
CM-6 1 - 2 IN. 6 25,000<br />
CM-8 UP TO 5 IN. 8 60,000<br />
CM-10 UP TO 6 IN. 10 100,000<br />
CM-12 UP TO 8 IN. 12 100,000<br />
CM-14 UP TO 10 IN. 14 100,000<br />
CM-16 UP TO 12 IN. 16 100,000<br />
Cornermax TM<br />
Part Number<br />
MAGNETIC CORNER PROTECTORS<br />
MAGNETIC CORNER PROTECTOR SPECIFICATIONS<br />
Magnetic Corner Protector<br />
Part Number<br />
**You Must Specify Inside Diameter of <strong>Coil</strong> and Sling Width<br />
WARNING The magnets are designed to keep the protector from falling from metallic loads and are not intended to prevent the protector or sling<br />
from sliding. <strong>Slings</strong> and protectors should be vertical or perpendicular to the load. The farther from vertical that the slings and protectors are, the more likely<br />
the protectors and slings will slide to become vertical and result in load instability and uncontrolled load descent. When using magnetic protectors always<br />
inspect for damage, prior to use. Keep magnets clean and free of debris.<br />
WARNING Wear Protection may not prevent cutting or other forms of sling damage. To avoid severe personal injury or death, personnel should be<br />
kept away from the load and never be under or near the load, while it is being lifted or suspended. A visual inspection of the sling must be made every time<br />
this sling is to be used. <strong>Slings</strong> that are damaged or determined to be unsafe shall not be used for any application. If the work load limit tag is missing, illegible<br />
or incomplete the sling shall not be used.<br />
WARNING Failure to follow proper use, care and inspection criteria could result in severe personal injury or death. <strong>It</strong> is your explicit responsibility to<br />
consider all risk factors prior to using any rigging device or product. Read and understand the information contained in this publication and follow OSHA and<br />
ASME guidelines. Use by untrained persons is hazardous. Synthetic products will fail if damaged, abused, misused, overused, or improperly maintained.<br />
WARNING Do not exceed work load limits. You are cautioned that all published work load limits and break strengths apply to only new and unused<br />
slings, assemblies and hardware. Work Load Limits are based upon: destruction testing, done in controlled, laboratory conditions, which will never be<br />
duplicated during actual usage and a moderately dynamic lifting or pulling operation. Instantaneous changes (drops or sudden pick ups) in excess of 10% of<br />
the work load, constitutes hazardous shock loading and THE WORKING LOAD LIMITS AS STATED, DO NOT APPLY.<br />
Style<br />
Heavy Duty Regular<br />
Sling Width<br />
(Inches)<br />
Protection Rating<br />
(Lbs)<br />
Magnetic Corner Protector<br />
O.A.L. (Inches)<br />
MCP 9 Regular UP TO 7 9-1/2<br />
MCP 12 Regular UP TO 10 12-1/4<br />
MCP 18 Regular UP TO 16 18-1/4<br />
MCP 9 HD Heavy Duty UP TO 7 9-1/2<br />
MCP 12 HD Heavy Duty UP TO 10 12-1/4<br />
MCP 18 HD Heavy Duty UP TO 16 18-1/4<br />
MCP-SL-9 Slotted-Regular UP TO 7 9-1/2<br />
MCP-SL-12 Slotted-Regular UP TO 10 12-1/4<br />
MCP-SL-18 Slotted-Regular UP TO 16 18-1/4<br />
MCP-SL-9 HD Slotted-Hvy. Duty UP TO 7 9-1/2<br />
MCP-SL-12 HD Slotted-Hvy. Duty UP TO 10 12-1/4<br />
MCP-SL-18 HD Slotted-Hvy. Duty UP TO 16 18-1/4<br />
MCP-C- **<br />
Curved - N/A<br />
LIFT-IT ® MANUFACTURING COMPANY, INC.<br />
4780 CORONA AVENUE • LOS ANGELES, CA 90058-3808<br />
(323) 582-6076 • Fax (323) 587-1630 • E-mail: liftit@pacbell.net • www.lift-it.com<br />
Slotted<br />
Curved