RoHS Certificate of Compliance - Heyco

September 20, 2012
RoHS Certificate of Compliance
After careful evaluation of EU Directives on Restriction of Hazardous Substances (RoHS),
Heyco Products, Inc. hereby certifies that all product lines including conduit, tubing, liquid tight
fittings, cordgrips, strain relief bushings, bushings, plugs, wire positioning devices, wire connecting,
terminating, IEC connectors, and all metal stamped products are fully compliant to the following EU
Directives:
2011/65/EU RoHS (version dated 2011 June 8), Restriction of the use of certain Hazardous
Substances in electrical and electronic equipment (recast)
ELV (version dated 2000 September 18), End-of-Life Vehicle, 2000/53/EC
WEEE (version dated 2003 January 27), Waste Electrical and Electronic Equipment, Directive
2002/96/EC
Directive 2006/122/EC of 12 December 2006 for restriction of Perfluorooctane sulfonates
Additionally, none of our products nor packing materials contain any unconditionally banned
substances, including Cadmium (Cd) and its compounds, Lead (Pb) and it’s compounds, Hexavalent
chromium (Cr) compounds, Mercury (Hg) and it’s compounds, and prohibited flame retardants,
namely Polybrominates biphenyls (PBB’s), nor Polybrominated diphenyl ethers (PBDE’s), nor
Polyfluoroalkyl compounds (PFCs) as listed in the table below in concentrations exceeding the
Maximum Trace Level (MTL):
Lead (Pb) (1)
Mercury (Hg)
Hexavalent Chromium (Cr+6)
Polybrominated Biphenyls (PBB)
Substance Maximum Trace Level (2)
Polybrominated Diphenyl Ethers (PBDE)
0.1% by weight (or 1000 ppm)
Cadmium (Cd) 0.01% by weight (or 100 ppm)
Polyfluoroalkyl compounds (PFCs), i.e.
Perfluorooctane sufonates (PFOS) and
Perfluorooctanoic acid (PFOA)
0.005% by mass (or 50 ppm)
(1) Lead, as an alloying element, is allowed up to 4.0% (40,000 ppm) in copper alloys, up to 0.35% (3,500 ppm) in steel,
and up to 0.40% (4,000 ppm) in aluminum alloys.
(2) The MTL does not apply to applications for which exemptions have been granted to the EU Directives
Regarding the use of decaBDE, which belongs to the group of polybrominated diphenyl
ethers (PBDE's), none of our products contain any banned decaBDE’s.
We anticipate this response satisfies your concerns regarding our products and requirements
for RoHS and WEEE compliance information, if not, please contact us and we will do our best to
provide additional information.
Thank you,
Patrick Sardoni
Quality Manager
Heyco Products, Inc.
1800 Industrial Way North
Toms River, NJ 08755
Disclaimer: This information is believed to be accurate and refers to the laws and products at the date of issue.
However, Heyco Products, Inc. makes no express or implied representations or warranties with respect to the
information contained herein.

September 20, 2012
Subject: People’s Republic of China Electronic Industry Standards SJ/T 11363 – 2006 and SJ/T
11364-2006 for Concentration Limits for Certain Hazardous Substances in Electronic Information
Products, (EIP) and Marking for Control of Pollution Caused by EIP.
All molded products produced and supplied by Heyco Products, Inc. do not contain any
hazardous substances as per the above referenced standard.
Metal stamped products of Heyco do contain lead of approximately 0.3%, which exceeds the
concentration limit of 0.1% as per the above referenced standard for concentration limits. This
amount of lead however, meets the requirements for the Restriction of the use of certain Hazardous
Substances, (RoHS) 2011/65/EU RoHS (version dated 2011 June 8), Restriction of the use of
certain Hazardous Substances in electrical and electronic equipment (recast), for the exception of
copper alloys. This is the only reportable hazardous substance contained in the copper alloy used for
Heyco metal stamped products.
Since all products supplied by Heyco are compliant to existing industry regulations and
standards, and have been compliant since inception, there are no plans to provide any additional
marking or labeling to indicate compliance to the above referenced standards for “Electronic
Information Products”.
Based upon information from our suppliers and our manufacturing processes, raw material
used meets all requirements for non-use of hazardous substances. Additionally, no components or
any other materials are added to the process that would affect or alter toxicity of the finished
products.
We anticipate this response satisfies your concerns regarding our products and our policy
regarding requirements for People’s Republic of China Electronic Industry Standards, if not, please
contact us and we will do our best to provide additional information.
Thank you,
Patrick Sardoni
Quality Manager
Heyco Products, Inc.
1800 Industrial Way North
Toms River, NJ 08755
Disclaimer: This information is believed to be accurate and refers to the laws and products at the date of issue.
However, Heyco Products, Inc. makes no express or implied representations or warranties with respect to the
information contained herein.