INTRONGlas PUH 4450 Product Number - Intron Jena
INTRONGlas PUH 4450 Product Number - Intron Jena
INTRONGlas PUH 4450 Product Number - Intron Jena
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>INTRONGlas</strong> <strong>PUH</strong> <strong>4450</strong><br />
<strong>Product</strong> Data Sheet Effective January 14, 2005<br />
Material designation: <strong>INTRONGlas</strong> <strong>PUH</strong> <strong>4450</strong><br />
<strong>Product</strong> <strong>Number</strong>: 310002 (Component A and B)<br />
Color: Transparent<br />
Characteristics: <strong>INTRONGlas</strong> <strong>PUH</strong> is a solvent-free, low-viscosity protective<br />
coating based on a highly reactive SH/En system that can be<br />
used preferrably in the thick film range (doming coating, film<br />
thickness: 1-2 mm). Very flexible, transparent protective<br />
coatings can be used by means of irradiation to effectively<br />
enhance the esthetic effect of print designs on polyester, PVC<br />
and metal films and on aluminium and plastic formed pieces.<br />
With <strong>INTRONGlas</strong> <strong>PUH</strong> presentation and promotional objectives<br />
can reach their full potential by combining content, esthetics and<br />
identification.<br />
Properties:<br />
Technical Characteristics - Lacquer<br />
• Three dimensional optical effect due to high transparency<br />
• Very good adhesion, long bonding life<br />
• Very stable under environmental conditions<br />
• Resistant to UV and climate, suited to outdoor use<br />
• Isocyanate-free components (elimination of skin irritations<br />
and environmental pollution)<br />
• Easy to use and very long pot life<br />
• Cures quickly, light curing<br />
• Variable flexibility to hard elasticity<br />
Appearance low-viscosity, transparent liquid<br />
Odor similar to thiol<br />
Viscosity<br />
(Dynamic Stress Rheometer,<br />
DIN 53019)<br />
2.5 – 3.5 Pas (20 °C)<br />
Solubility Acetone, chloroform, methyl ethyl ketone
Technical Characteristics - Coating<br />
Appearance Colorless, glossy decorative protective coating<br />
Cross cutting value<br />
(DIN 53151)<br />
Adhesion<br />
(INSTRON 4467,<br />
DIN 53283)<br />
Climate change test<br />
(VDA-Test, 240 hr.)<br />
GT 0<br />
31 - 36 Mpa<br />
2<br />
No tunneling, separation or clouding of lacquer<br />
coat<br />
Preparatory Surface Treatment: The surfaces that are to be coated have to be cleaned<br />
using ethanol or isopropyl alcohol and then coated<br />
immediately after evaporation of the solvent.<br />
Use: <strong>INTRONGlas</strong> <strong>PUH</strong> <strong>4450</strong> consists of components A and<br />
B that have to be weighed out and mixed together right<br />
before application.<br />
The components of <strong>INTRONGlas</strong> <strong>PUH</strong> <strong>4450</strong> and<br />
materials already mixed must be stored so that they are<br />
not exposed to light.<br />
To make the coating, both components must be weighed<br />
out at the following ratio:<br />
Component A : 1.0 g<br />
Component B : 2.0 g<br />
Thoroughly mix the components A and B by stirring (for approx. 5 minutes) after carefully<br />
weighing them (± 0.1 g). Once the solution is free of bubbles (approx. 30 minutes), it may be<br />
used for coating. The mixture can be safely stored in refrigeration and without exposure to<br />
light for approx. 5 days.<br />
<strong>INTRONGlas</strong> <strong>PUH</strong> <strong>4450</strong> can be applied with the aid of suitable metering equipment<br />
(manual or pneumatic) in continuous or intermittent process. By eliminating pot lifes and<br />
complicated cleaning processes as a result of production cycles, it is possible to achieve very<br />
economic effects.<br />
Setting: <strong>INTRONGlas</strong> <strong>PUH</strong> <strong>4450</strong> hardens with the aid of the<br />
INTRON LHG-3 light curing device. The exposure times<br />
range between 3 and 12 minutes depending on film<br />
thickness. This should be tested, however, in preliminary<br />
tests with a small batch.
3<br />
Delivery form: <strong>INTRONGlas</strong> <strong>PUH</strong> <strong>4450</strong> (components A and B) comes in<br />
500 g, 1000 g and 5000 g special containers.<br />
Storage: The components A and B of <strong>INTRONGlas</strong> <strong>PUH</strong> <strong>4450</strong> may<br />
be safely stored at room temperature and without<br />
exposure to light for at least 3 months. The compound<br />
(components A + B) may be safely stored for 5 days in<br />
refrigeration.<br />
refrigeration<br />
Safety information: Information about hazards, labeling, safety measures and<br />
transport is available in the relevant Material Safety Data<br />
Sheet.<br />
The necessary safety measures for handling, information<br />
about the Hazardous Materials Directive, TA-Luft,<br />
maximum working place concentrations and other<br />
environment-related data can be taken from the EU<br />
Material Safety Data Sheet for <strong>INTRONGlas</strong> <strong>PUH</strong> <strong>4450</strong>.<br />
The above information is provided as approximate values based upon laboratory testing and<br />
our practical experience. The product information, including any assurances regarding<br />
product suitability, is believed to be reliable and reflects the current state of technology.<br />
Environmental effects, materials, application equipment and techniques are beyond our<br />
control. In any case, the customer is responsible for determining the suitability of the<br />
material before using under practical conditions.<br />
INTRON - Gesellschaft für digitale Farbtransferdrucktechnik mbH<br />
Hauptstrasse 42<br />
D-07751 Rothenstein<br />
Tel. +49 36424 88 40<br />
Fax +49 36424 88 488<br />
e-mail: info@<strong>Intron</strong>-jena.de