E-BoxX product range - Walther

5
Industry-Line
98100113 98100115 98100110
Art. no.
98100108
98100109
98100110
98100111
Enclosure Residual current Charging point Identification Technology Data Added-value
W x H x D devices and and and communi- services and
(mm) circuit breakers charging power operation cation CI design
183 x 370 x 152
Connection
terminals
2 x 5 x 25 mm²
183 x 370 x 152
Connection
terminals
2 x 5 x 25 mm²
290 x 404 x 171
Connection
terminals
2 x 5 x 25 mm²
183 x 370 x 152
Connection
terminals
2 x 5 x 25 mm²
RCBO 16 A 2-pole
type A
RCBO 16 A 2-pole
type A extern
RCD 40 A 4-pole
type B
AC/DC sensitive
MCB 16 A 3-pole+N, C
RCD 40 A 4-pole
type B
AC/DC sensitive extern
MCB 16 A 3-pole+N, C
Industry-Line
O
74
The listed articles represent a current selection from the product line. In addition to this, there are many other variants of
charging point – charging power – operation – technology and CI. Contact our specialists.
75
O
E-BoxX
The Industry-Line product line is based on the enclosure system of Walther socket combinations for decentralised energy distribution
that has proven its effectiveness over many years. The spacious plastic enclosure provides enough space for the necessary safety
devices such as RCD (residual current device), miniature circuit breaker (MCB) as well as the charge controller for communication with
the electric vehicle. These devices for DIN-rail mounting can be accessed from the outside, behind a flap, depending on the enclosure
design.
The safety devices can also be integrated into the upstream installation as an alternative. This is done by specialist electrical companies
in compliance with the manufacturer’s specifications and relevant installation regulations.
The Industry-Line enables you to provide single-phase and/or three-phase charging in the power range from 3 kW to 22 kW, depending
on configuration. Optionally, it is also possible to provide a Schuko socket for charging according to mode 2, or for charging
pedelecs.
Depending on the version, either a type 2 charging socket or a fixed cable (straight or spiral) with the appropriate vehicle connector
(type 1 or type 2) for the electric vehicle is provided, with the cable cross section according to the available max. charging power. In the
E-BoxX with type 2 charging socket, the electric vehicle is connected using an additional mode 3 charging cable.
Knob switches, key-operated switches and LEDs for signalling are installed, depending on the variant, for operation and/or activation
of the charging procedure. Optionally, the E-BoxX units have an integrated meter for reading off the “driven” electricity.
Additional mechanical protection is available for the Industry-Line as an option, comprising roofs and side protection. All variants from
the Walther range of free standing pillars can be used here.
Application/location of use: Carports, underground garages, multi-storey car parks, optionally in conjunction with local
energy management.
98100116 98100108 98100112 + 620 WL 82 ET
Art. no.
98100112
98100113
98100114
98100115
Enclosure Residual current Charging point Identification Technology Data Added-value
W x H x D devices and and and communi- services and
(mm) circuit breakers charging power operation cation CI design
290 x 404 x 171
Connection
terminals
2 x 5 x 25 mm²
290 x 404 x 171
Connection
terminals
2 x 5 x 25 mm²
290 x 404 x 171
Connection
terminals
2 x 5 x 25 mm²
290 x 404 x 171
Connection
terminals
2 x 5 x 25 mm²
RCD 40 A 4-pole type B
AC/DC sensitive
MCB 16 A 3-pole+N, C
RCD 40 A 4-pole type B
AC/DC sensitive
MCB 32 A 3-pole+N, C
RCD 40 A 4-pole type B
AC/DC sensitive extern
MCB 32 A 3-pole+N, C
RCBO 16 A 2-pole type A
RCD 40 A 4-pole type B
AC/DC sensitive
MCB 32 A 3-pole+N, C
RCBO 16 A 2-pole type A
5