Anteo Light Commercials

since 1969
LIGHT COMMERCIALS

F3 V050
TAIL-LIFT FOR PANEL VANS - 2 CYLINDERS
load capacity: 500 kg
LIGHT
COMMERCIALS
TECHNICAL DATA
Load Capacity 500 kg
Voltage 12 V
Max Power Consumption 130 Amp
Max Pressure Valve Setting 140 bar
Up-stroke Speed (Full Load) 5 m/min
Down-stroke Speed (Full Load) 8 m/min
Oil Tank Capacity 2 litres
Noise Level < 70 dB
Electric Motor Power 1600 Watt
Standard Platform Depth 1400 mm - 1600 mm
Standard Platform Width 1450 mm
Weight for Complete Tail-lift with
Platform Depth 1400 mm
Weight for Complete Tail-lift with
Platform Depth 1600 mm
179 kg
185 kg
Mounting Bolted assembly plates
Platform Opening
Powered opening of the
platform with 1 doubleacting
tilting cylinder
Anteo reserves the right to change weights and technical specifications without
prior notice. No indemnity for damages can be claimed from Anteo for changes
in technical specifications and/or in weight.
APPLICATIONS
WEIGHT
STARTING AT
179 kg!
The completely new cantilever tail-lift
F3 V050 has been designed and built for the
3.5 ton panel van range and can be installed
easily without modifications to the host
vehicle.
Installation is made quick and easy with
individual mounting brackets for most vans.
F3 V050 is especially designed for:
Citroen JUMPER / RELAY
Fiat NEW DUCATO
Ford NEW TRANSIT
Iveco DAILY
Mercedes NEW SPRINTER
Mercedes VITO
Nissan INTERSTAR
Nissan PRIMASTAR
Opel MOVANO
Opel VIVARO
Peugeot BOXER
Renault MASTER
Renault TRAFFIC
VolksWagen CRAFTER
VolksWagen TRANSPORTER
Bolted assembly
plates
Powered opening of the platform
Double-acting tilting cylinder
Power pack with simplified access
STANDARD EQUIPMENTS
PLATFORM
- Platform in aluminium alloy.
MECHANICAL FUNCTIONS
- Powered opening of the platform (ensures platform opening even with extreme and
winter climatic conditions).
- Automatic hydraulic tilting of platform to ground.
- Tilt of platform in all positions.
- Mechanical stop of tail-lift arms against lift frame (adjustable).
HYDRAULIC CHARACTERISTICS
Power pack equipped with:
- closing seal, compact and soundproof;
- electrical connections by means of modular extractable board;
- electrical board for any type of connection.
- Power pack with simplified access through a hinged cover.
- 1 single-acting lifting cylinder with lubrication.
- 1 double-acting tilting cylinder.
- Lifting cylinder protected by rubber gaitor.
- Built-in safety solenoid valves on every cylinder.
- Tank with air filter.
- Chrome-plated steel cylinder rods with high yield limit.
- Flow adjusters compensated on all downward movements.
CONTROLS
- Super slim external fixed control box and ON - OFF cabin switch.
- Illuminated control panel.
- Control with no electronic components.
- Two-hand use for operator’s safety.
- Motor with thermal safety device.
- Motor relay with 80 A silver pin (peak current).
CHOICE OF MOUNTING
- Bolted assembly plates.
A dedicated bracket kit is available for every vehicle type.
The assembly is quick, simple and does not require any modification to the vehicle frame
or body, except for the fitting of the super slim control box and of the remote control
with socket/plug/spiral cable. Adjustable lift height stop integrated in the lift frame to
eliminate body damage.
PRODUCT FINISHING
- All steel parts of the hydraulic kit have been previously sandblasted, then treated
with hexacrylic electrocataphoresis (except for cylinders, painted with bicomponent
polyurethane enamel).
- Material conform to EC standards.
- Steel cataphoresis-treated pins.
- Anti-friction self-lubricating bushings.
- Delivered fully assembled and tested, it is to be mounted to the chassis by bolting,
eliminating need to repaint.
2 3

VCE 075
TAIL-LIFT FOR PANEL VANS - 4 CYLINDERS
load capacity: 750 kg
LIGHT
COMMERCIALS
TECHNICAL DATA
E
Mod.
Load capacity
(center of gravity
at 600 mm)
B
T
Standard Platform
Dimensions
A
Weight *
E A B B’
Kg
Depth Width max min max min min
VCE 075 C
1200
210 990 265 465 424 - 140
750 Kg 1400* on demand
VCE 075 H 1600
218 1210 331 585 511 - 140
*Indicative weight of tail-lift supplied in kit with a 1400 mm depth platform. The weight may vary according to width.
Anteo reserves the right to change weights and technical specifications without prior notice.
No indemnity for damages can be claimed from Anteo for changes in technical specifications and/or in weight.
768
APPLICATIONS
The classical tail-lift VCE 075 has been
designed and realised for commercials
vehicles.
VCE 075 is especially designed for:
Iveco DAILY
Renault MASCOTT
Brackets to be welded
by the fitter
T
STANDARD EQUIPMENTS
PLATFORM
- Platform in aluminium alloy.
MECHANICAL FUNCTIONS
- Powered opening of the platform (ensures platform opening even with
extreme and winter climatic conditions).
- Automatic hydraulic tilting of platform to ground.
- Tilt of platform in all positions.
HYDRAULIC CHARACTERISTICS
The power pack has been designed to be fitted on the vehicle side between
the front and rear axle. It is equipped with:
- closing seal, and soundproof;
- 2 single-acting lifting cylinders with lubrication.
- 2 double-acting tilting cylinders.
- Built-in safety solenoid valves on every cylinder.
- Tank with air filter.
- Chrome-plated steel cylinder rods with high yield limit.
CONTROLS
- Super slim external fixed control box and ON - OFF cabin switch.
- Illuminated control panel.
- Control with no electronic components.
- Two-hand use for operator’s safety.
- Motor with thermal safety device.
- Motor relay with 80 A silver pin (peak current).
MOUNTING
- Mounting brackets shaped to be fitted on vehicles with top hat section
chassis. Mounting brackets to be welded to the main beam.
PRODUCT FINISHING
- Material conform to EC standards.
- Hard chromium-plated steel pins.
- Anti-friction self-lubricating bushings.
- Delivered fully assembled and tested.
- Rear bumper not available.
4 5

F3MH 075
HALF LIFT - 2 CYLINDERS
load capacity: 750 kg
LIGHT
COMMERCIALS
TECHNICAL DATA
Mod.
Load capacity
(center of gravity
at 600 mm)
Factory-welded
bracket
Standard Platform
Dimensions Weight*
Kg
A E B
Depth Width min. max. max. min.
Bolted
bracket
F3MH 075 C
1200
240 260 470 1055 505 186
750 Kg 1400* on demand
F3MH 075 H 1600
248 365 565 1225 580 186
*Indicative weight of tail-lift supplied in kit without rear bumper and with a 1400 mm depth platform.
The weight may vary according to width.
Anteo reserves the right to change weights and technical specifications without prior notice.
No indemnity for damages can be claimed from Anteo for changes in technical specifications and/or in weight.
T
APPLICATIONS
The classic F3M range of tail lifts has been
designed for bodied chassis cab vehicles
with floor heights up to 1225mm.
The particularly slim arms allows the fitting
on very narrow vans of 2000mm/2100mm
(van minimum width to be checked
according to chassis width).
STANDARD EQUIPMENTS
PLATFORM
- Platform in aluminium alloy.
MECHANICAL FUNCTIONS
- Mechanical hydraulic tilting of platform to
ground.
- Tilt of platform in all positions.
- Anti-friction self-lubricating bushings and
chromed pins.
- Platform opening with 1 single-acting
tilting cylinder and spring.
HYDRAULIC CHARACTERISTICS
Compact power pack equipped with:
- closing seal.
- 1 single-acting lifting cylinder with
lubrication.
- 1 single-acting tilting cylinder.
- Built-in safety solenoid valves on every
cylinder.
- Tank with air filter.
- Chrome-plated steel cylinder rods with
high yield limit.
- Flow adjusters compensated on all
downward movements.
CONTROLS
- External control box.
- Illuminated control panel.
- Control with no electronic components.
- Cut off switch with key.
- Two-hand use for operator’s safety.
- Motor with thermal safety device.
- Motor relay with 80 A silver pin (peak
current).
MOUNTING
With an adjustable bolted bracket and
a bracket that has already been factorywelded
in a fixed position. Quick fitting:
rear bumper already bolted in 2 parts.
PRODUCT FINISHING
- Material conform to EC standards.
- Hard chromium-plated steel pins.
- Anti-friction self-lubricating bushings.
- Delivered fully assembled and tested, it is
to be mounted to the chassis by bolting,
eliminating need to repaint.
CEM 075
HALF LIFT - 4 CYLINDERS
load capacity: 750 kg
LIGHT
COMMERCIALS
TECHNICAL DATA
*Indicative weight of tail-lift supplied in kit with a 1400 mm depth platform.
The weight may vary according to width.
Anteo reserves the right to change weights and technical specifications without prior notice.
No indemnity for damages can be claimed from Anteo for changes in technical specifications and/or in weight.
6 7
Mod.
Brackets to
be welded
Load capacity
(center of gravity
at 600 mm)
B
A
T
Standard Platform
Dimensions Weight*
Kg
A E B
Depth Width min. max. max. min.
CEM 075 C
1200
191 265 465 990 424 140
on
750 Kg 1400*
demand
CEM 075 H 1600
203 331 585 1210 511 140
E
T
APPLICATIONS
The classic CEM 075 tail lift has been
designed for bodied chassis cab vehicles
with particularly wide chassis. This tail lift
has been designed so that the arms of the
lift frame straddle the chassis member.
CEM 075 is especially designed for:
Citroën JUMPER
Fiat DUCATO
Ford TRANSIT
Mercedes SPRINTER
Peugeot BOXER
VolksWagen LT/CRAFTER
STANDARD EQUIPMENTS
PLATFORM
- Platform in aluminium alloy.
MECHANICAL FUNCTIONS
- Powered opening of the platform
(ensures platform opening even with
extreme and winter climatic conditions).
- Automatic hydraulic tilting of platform to
ground.
- Tilt of platform in all positions.
- Anti-friction self-lubricating bushings and
chromed pins.
HYDRAULIC CHARACTERISTICS
The power pack has been designed to be
fitted on the vehicle side between the front
and rear axle. It is equipped with:
- closing seal, compact and soundproof;
- 2 single acting lifting cylinders with
lubrication.
- 2 double acting tilting cylinders.
- Built-in safety solenoid valves on every
cylinder.
- Tank with air filter.
- Chrome-plated steel cylinder rods with
high yield limit.
- Flow adjusters compensated on all
downward movements.
CONTROLS
- External control box.
- Illuminated control panel.
- Control with no electronic components.
- Cut off switch with key.
- Two-hand use for operator’s safety.
- Motor with thermal safety device.
- Motor relay with 80 A silver pin (peak
current).
MOUNTING
Mounting brackets shaped to be fitted on
vehicles with top hat section chassis.
Mounting brackets to be welded to the main
beam.
PRODUCT FINISHING
- Material conform to EC standards.
- Hard chromium-plated steel pins.
- Anti-friction self-lubricating bushings.
- Delivered fully assembled and tested.

F3M 075 - F3M 10
CANTILEVER TAIL-LIFTS - 2 CYLINDERS
load capacity: 750 kg - 1000 kg
LIGHT
COMMERCIALS
TECHNICAL DATA
Mod.
Load capacity
(center of gravity
at 600 mm)
B
A
T E
Bolted brackets
Standard Platform
Dimensions Weight*
Kg
A E B
Depth Width min. max. max. min.
F3M 075 C
1200
251 305 470 1055 505 186
750 Kg 1400* on demand
F3M 075 H 1600
259 350 550 1210 580 186
F3M 10 H
1400*
382 205 480 1165 698 260
1000 Kg 1600 on demand
F3M 10 HS 1800
391 250 585 1375 774 260
*Indicative weight of tail-lift supplied in kit without rear bumper and with a 1400 mm depth platform.
The weight may vary according to width.
Anteo reserves the right to change weights and technical specifications without prior notice.
No indemnity for damages can be claimed from Anteo for changes in technical specifications and/or in weight.
T
APPLICATIONS
The classic F3M range of tail lifts has been
designed for bodied chassis cab vehicles.
Dedicated mounting brackets are available
for every vehicle type. The assembly is quick,
simple and does not require any modification
to the chassis. F3M 075 and F3M 10 are
especially designed for:
Citroën JUMPER
Fiat DUCATO
Ford TRANSIT
Iveco DAILY
Mercedes SPRINTER
Nissan CABSTAR
Nissan ATLEON
Peugeot BOXER
VolksWagen LT/CRAFTER
STANDARD EQUIPMENTS
PLATFORM
- Platform in aluminium alloy.
MECHANICAL FUNCTIONS
- Mechanical hydraulic tilting of platform to
ground.
- Tilt of platform in all positions.
- Platform opening with 1 single-acting
tilting cylinder and spring.
HYDRAULIC CHARACTERISTICS
Compact power pack equipped with:
- closing seal.
- 1 single-acting lifting cylinder with
lubrication.
- 1 single-acting tilting cylinder.
- Built-in safety solenoid valves on every cyl.
- Tank with air filter.
- Chrome-plated steel cylinder rods with
high yield limit.
- Flow adjusters compensated on all
downward movements.
CONTROLS
- External control box.
- Illuminated control panel.
- Control with no electronic components.
- Cut off switch with key.
- Two-hand use for operator’s safety.
- Motor with thermal safety device.
- Motor relay with 80 A silver pin (peak
current).
CHOICE OF MOUNTING
Adjustable bolted brackets.
Installation is made quick and easy with
individual mounting brackets for every van.
F3M 075: rear-bumper bolted to the arm.
F3M 10: rear-bumper in 3 pieces bolted to
the main beam.
PRODUCT FINISHING
- Material conform to EC standards.
- Hard chromium-plated steel pins.
- Anti-friction self-lubricating bushings.
- Delivered fully assembled and tested, it is
to be mounted to the chassis by bolting,
eliminating need to repaint.
5 VERSIONS AND VARIOUS SOLUTIONS ACCORDING TO WHEEL BASE AND OVERHANG
F3M 075 - F3M 10
are available for all vehicles
with double “C” chassis.
F3M 075
can be installed on all
vehicles with top hat
section chassis and vans.
Citroën JUMPER
Fiat DUCATO
Peugeot BOXER
F3M 075
Quick fitting without
making holes in the chassis
using the original holes.
Note:
SC (mm)
The instructions reported refer to vehicles with original chassis that have not been lengthened. If the chassis has been lengthened, refer to the solution described at point 2.
Ford TRANSIT
F3M 075 C/H
Quick fitting without
making holes in the chassis
using the original holes.
Note:
The instructions reported refer both to vehicles with original chassis and to vehicles with lengthened chassis, with rear-wheel drive.
Mercedes SPRINTER
SPRINTER 06
VolksWagen LT/CRAFTER
F3M 075 - F3M 10
Quick fitting without
making holes in the chassis
using the original holes.
The F3M075 and F3M10 taillifts
are available on demand
for the new 2006 vehicles
Sprinter and Crafter with wh.
base of 3250 (single wh.) and
wh. bases of 3665 and 4325
(single wh. and double wh.).
Mod. MB Sprinter Wheel
Base
8 9
F3M 075
A
(mm)
A
(mm)
SC (mm)
Wheel
Type
Bracket
311 3000 single X
208 - 311 - 313 3550 single X
311 - 313 4025 single Y
316 4025 single XZ
411 - 413 - 416 3550 double Z
411 - 413 - 416 4025 double W
616 4025 double XY
F3M 10 H 616 4025 double XW
POWER UNIT
X
A
(mm)
Anchoring brackets
467 mm
712 mm
Z
655 mm
155 mm
XY
747 mm
Y
FLAT
PUSH-BUTTON
PANEL
SC (mm)
962 mm
W
685 mm
XZ
632 mm
XW
ON-OFF

CE 075
CANTILEVER TAIL-LIFTS - 4 CYLINDERS
load capacity: 750 kg
LIGHT
COMMERCIALS
TECHNICAL DATA
Mod.
Brackets to
be welded
Load capacity
(center of gravity
at 600 mm)
B
1087 max.
Standard Platform
Dimensions Weight*
Kg
A E B
Depth Width min. max. max. min.
CE 075 C
1200
249 250 450 990 451 160
750 Kg 1400* on demand
CE 075 H 1600
257 316 570 1210 537 160
*Indicative weight of tail-lift supplied in kit without rear bumper and with a 1400 mm depth platform.
The weight may vary according to width.
Anteo reserves the right to change weights and technical specifications without prior notice.
No indemnity for damages can be claimed from Anteo for changes in technical specifications and/or in weight.
A
T
E
1403
T
APPLICATIONS
The classic CE 075 tail lift has been
designed for bodied chassis cab vehicles
with floor heights up to 1215mm.
STANDARD EQUIPMENTS
PLATFORM
- Platform in aluminium alloy.
MECHANICAL FUNCTIONS
- Platform opening by built-in springs on
tilting cylinders.
- 3 pieces bumper to be welded to the lift
beam by the installer.
- Automatic hydraulic tilting of platform to
ground.
- Tilt of platform in all positions.
HYDRAULIC CHARACTERISTICS
Power pack equipped with:
- closing seal, compact and soundproof.
- 2 single-acting lifting cylinders with
lubrication.
- 2 single-acting tilting cylinders.
- Built-in safety solenoid valves on every
cylinder.
- Tank with air filter.
- Chrome-plated steel cylinder rods with
high yield limit.
- Flow adjusters compensated on all
downward movements.
CONTROLS
- External control box.
- Illuminated control panel.
- Control with no electronic components.
- Cut off switch with key.
- Two-hand use for operator’s safety.
- Motor with thermal safety device.
- Motor relay with 350 A silver pin (peak
current).
MOUNTING
- Brackets to be welded to the main beam.
PRODUCT FINISHING
- Material conform to EC standards.
- Chromium-plated steel pins.
- Anti-friction self-lubricating bushings.
- Delivered fully assembled and tested.
RCE 075
RETRACTABLE TAIL-LIFT - 4 CYLINDERS
load capacity: 750 kg
LIGHT
COMMERCIALS
TECHNICAL DATA
*Indicative weight of tail-lift supplied in kit with a 1200 mm depth platform.
The weight may vary according to width.
**3 folds special platform.
Anteo reserves the right to change weights and technical specifications without prior notice.
No indemnity for damages can be claimed from Anteo for changes in technical specifications and/or in weight.
10 11
Mod.
B
Load capacity
(center of gravity
at 600 mm)
RCE 075 H 750 Kg
Standard Platform
Dimensions Weight*
Kg
A E B
Depth Width min. max. max. min.
1200*
1500**
T
A
2100 320 - 450 1210
E
Bushes
to be welded
945
1065**
T
273
APPLICATIONS
The retractable tail-lift F3RE is the ideal
tail-lift for distribution vehicles due to its
versatility, large platforms and ease of use.
The tail-lift is stowed away under the
vehicle making it ideal for dock loading.
RCE 075 is available for bodied chassis cab
vehicles up to 7.5 tonnes GVW.
STANDARD EQUIPMENTS
PLATFORM
- Platform in aluminum alloy
MECHANICAL FUNCTIONS
- Tail-lift deployment by means of adjustable
chromium plated guides of high yield steel.
- Tail-lift deployment and stowage under
chassis by means of double extension
cylinder.
- Automatic hydraulic tilting of platform to
ground.
HYDRAULIC CHARACTERISTICS
Compact power pack equipped with:
- closing seal, and soundproof.
- 2 single-acting lifting cylinders with
lubrication.
- 2 single-acting tilt cylinders with
lubrication.
- Memory cylinder with automatic tilting at
ground level.
- 1 double ram for tail-lift deployment and
stowage under chassis.
- Built-in safety solenoid valves on every
cylinder.
- Tank with air filter.
- Chrome-plated steel cylinder rods with
high yield.
- Flow adjusters compensated on all
downward movements.
CONTROLS
- External control box.
- Illuminated control panel.
- Control with no electronic components.
- Cut off switch with key.
- Two-hand use for operator’s safety.
- Motor with thermal safety device.
- Motor relay with 350 A silver pin (peak
current)
- Proximity switches for automatic
positioning of tail-lift.
MOUNTING
- Bushes to be welded to the main beam.
PRODUCT FINISHING
- Material conform to EC standards.
- Chromium-plated steel pins.
- Anti-friction self-lubricating bushings.
- Delivered fully assembled and tested.

FOR BIG CITIES WITH SMALL SPACES
A WIDE RANGE OF TAIL-LIFTS FOR LIGHT COMMERCIALS VEHICLES.
since 1969
anteo spa - via Nobili, 68/70 - 40062 Molinella (BO) Italia - tel +39 0516906611 - fax +39 0516906604 - www.anteo.com - anteo@anteo.com