Series 6 I/O 9/8 module

Series 6
I/O 9/8
module
I/O 9/8MD HS
The I/O 9/8 module is a
component used for controlling
elevators, turnstiles and
revolving door stops etc. in
more complex access control
environments.
Its current status is relayed
by the nine digital inputs
and eight relays – each with
a change-over contact – to
the superordinate control
unit (ACT e.g. B6L, M6L,
TC16) which evaluates this
and then controls the electrical
function units.
An I/O 9/8 module can also
bundle the signals of several
doors e.g. door opening push
buttons or door open messages
and transmit the control
signals for door opening
to the doors. This considerably
reduces the number
of separate door modules
and the amount of wiring required.
An I/O 9/8 module can
also be used for doors that
need to be controlled in remote
premises. Up to eight
doors can be opened using
straightforward access control,
and three to four doors
in the case of more complex
monitoring requirements
such as door status messages,
internal push button and
local alarm. Communication
between the I/O 9/8 module
and the control centre is via
RS485 and the DP1 protocol
and can bridge a distance of
up to 6,000 metres.
The I/O 9/8 module is available
in two styles: the wall
version can be surfacemounted
on the wall or, for
example, inconspicuously in
a false ceiling. The I/O 9/8
top-hat module is designed
for snap mounting on standardised
top-hat rails and can
thus be conveniently integrated
into switchgear assemblies.
I/O 9/8MD WM

WN 05361951532, E, 3, BD, 12/2009
Technical data I/O 9/8 module
Input voltage 16 V to 36 VDC (SELV)
16 V to 24 VAC (SELV)
Wall mounting: optional: 230 V power supply
unit can be retrofitted
Consumption Device: max. 5 W, e.g. 200 mA at 24 V
Interfaces RS485
Protocols DP1
Anti-tamper
monitoring
Available
Outputs 8 relays: maximum load 60 W
45 VDC/2 A (SELV)
30 VAC/2 A (SELV)
Inputs
(digital)
Cable
(recommended)
9 opto-couplers, plus-switching:
load 24 VDC (max. 36 VDC, 24 VAC/10 mA)
Switching thresholds:
active at 10 VDC or 9 VAC
passive at 4 VDC or 4 VAC
RS485 data cable:
J-2Y(ST)Y 2 x 2 x 0.6 mm 2 ST III BD
Relay cable:
J-2Y(ST)Y 2 x 2 x 0.6 mm 2 ST III BD
Digital input cable:
J-2Y(ST)Y 2 x 2 x 0.6 mm 2 ST III BD
Power supply cable:
J-2Y(ST)Y 2 x 2 x 0.6 mm 2 ST III BD
Line length RS485: max. 6,000 m
Relay: max. 200 m
Digital inputs: max. 100 m
Power supply: max. 200 m complying with
the permissible input voltage limits
Ambient
conditions
General
design
Protection
rating
Resistance to
interference
Emission
standard
Operating temperature range:
-20°C to +50°C
Storage temperature range:
-20°C to +70°C
Humidity range:
0 to 80%, non-condensing
Wall mounting:
EN 60 950, protection class III (at 230
VAC operation protection class I)
Top-hat rail mounting:
EN 60 950, protection class III
Mounting on rails in accordance with:
EN 60715
TH35-7.5 top-hat rails for installation in
switchgear assemblies complying with
EN 60439-1
IP 30
EN 61000-6-2
Immunity for industrial environments
EN 61000-6-3
Emission standard for residential environments
Dimensions Wall mounting:
(W x H x D) 145.5 x 243.5 x 61 mm
Top-hat rail mounting:
(W x H x D) 198 x 75 x 71 mm
corresponds to a device width of 11 horizontal
pitch
Casing colour Wall mounting: RAL 7016 (anthracite grey)
Top-hat rail mounting: anodised aluminium
Weight Wall mounting:
1,500 g without 230 V PSU
2,100 g with 230 V PSU
Top-hat rail mounting: 600 g
Subject to technical alterations
DORMA STA
(Security, Time + Access)
DORMA
Time + Access GmbH
Mainzer Straße 36-52
D-53179 Bonn
Tel. +49 228 8554-0
Fax +49 228 8554-175
www.dorma-time-access.com
DORMA GmbH Co. KG
DORMA Platz 1
D-58256 Ennepetal
Tel. +49 2333 793-0
Fax +49 2333 793-495
www.dorma.com