Series 6 - Dorma

A DORMA Group Company
Series 6
M6L
Terminal
The compact LAN terminal
- M6L - is equally suitable
for time acquisition and access
control and is also the
perfect solution for combined
time and access applications.
Designed specifically for
internal applications,
the elegant, discreet and
extremely flat surface mount
housing can be integrated
into practically all architectural
designs.
The terminal is equipped
with an easy-to-read, 2-line,
backlit display and a
membrane keyboard with
assignable function keys.
The keys (up to 12) can be
used to enter PIN numbers
(10 keys) or alternatively,
they can be configured as
function and information
keys. The user interface
is designed in a clear and
intuitive manner and can
be used directly without any
additional training.
The M6L is available with all
conventional proximity reading
technologies and various
swipe readers.
In addition to the LAN
interface, this terminal is
equipped with serial connections
and can therefore
easily establish a direct
connection between the
LAN-/WAN connections, the
in-house wiring and further
time and access terminals or
readers.

WN 05284951532, E, 1.5, DD, 06/2005
Technical Data M6L Terminal
Input voltage 16 V to 36 VDC (SELV)
16 V to 24 VAC (SELV)
Consumption Max. 8 W
Data retention Lithium backup battery to save data in RAM
in the event of a power failure. The continuous
back-up life of the battery ranges
between 3-5 years. Type CR2032 / 3 V, 230
mAh, plugged
Service life approx. 10 years
Reader
(internal)
Transmitter
frequency
The following readers can be installed:
proximity readers:
INDALA - ca. 5 cm
TROVAN - ca. 8 cm
MIFARE - ca. 4 cm
LEGIC - ca. 4 cm (segm./unsegm.)
HITAG - ca. 5 cm
Typical reading distances for badges in
check card format
swipe readers:
Magnet track 2
Magnet track 3
Bar codes
INDALA: 125 kHz
TROVAN: 125 kHz
MIFARE: 13.56 MHz
LEGIC: 13.56 MHz
HITAG: 125 kHz
Interfaces Host: Ethernet (10/100 Mbits)
Sub: RS485 or DCW ® (currently in preparation)
Tamper Light barrier
contact
Outputs 2 relays: load capacity max. 60 W
40 VDC / 2 A (SELV)
35 VAC/ 2 A (SELV)
Inputs
(digital)
Cable
(recommended)
3 optocoupler - positive switching:
load capacity 24 VDC (max. 36 VDC) / 20 mA
Operating points
DC: ca. 11 V
AC: ca. 9 Veff
Data cable LAN:
in accordance with Ethernet specification,
min. Cat 5 (UTP/s, S-UTP)
Data cable RS485:
J-2Y(ST)Y 2 x 2 x 0.6 mm 2 ST III BD
Data cable DCW ® :
I-Y(ST)Y 2 x 2 x 0.8 mm 2
Cable relay:
J-2Y(ST)Y 2 x 2 x 0.6 mm 2 ST III BD
Cable digital inputs:
J-2Y(ST)Y 2 x 2 x 0.6 mm 2 ST III BD
Cable voltage supply:
J-2Y(ST)Y 2 x 2 x 0.6 mm 2 ST III BD
Cable lengths LAN: max. 100 m in acc. with IEEE-
802.3u
RS485: 4,000 m at 9,600 baud
DCW ® : 300 m
Voltage supply: max. 200 m taking account
of the permissible input voltage limits
Environmental
conditions
Operating temperature range:
–10°C to +50°C
Storage temperature:
–10°C to +70°C
Humidity range:
0 to 80%, non-condensing
General EN 60 950-1, protection class III
design
Type of pro- IP 30
tection
Immunity to EN 61000-6-2
interference
Interference EN 61000-6-3
emission
Dimensions (WxHxD) 176 x 176 x 55 mm
Colour of Gray blue, RAL 2208005
housing
Weight Ca. 660 g
Display LCD display, 2 x 16 characters, backlit,
temperature-dependent contrast settings
Keyboard Membrane keyboard with up to 12 keys
Mounting Lateral distance: > 16.5 cm
height and Distance to bottom edge: 150 cm
space requirement
Technical alterations reserved
MBB Gelma GmbH
Mainzer Straße 36-52
D-53179 Bonn
Tel. +49 228 8554-0
Fax +49 228 8554-175
A DORMA Group Company
www.mbb-gelma.com