Download pdf Brochure - James G. Murphy Co.

NO MINIMUMS - NO RESERVES
Board Press-Caul Transfer & Recovery System
WASHINGTON 6475 ton, 4’x24’ simultaneous 16-opening press, (19) 5”x64”x306”
heating & cooling platens, 1150 hp 11-pump hydraulic unit, (2) 150 hp hot press
pumps, 30 hp filter cooler, 8” inlet & outlet headers, all controls & electrics, catwalk,
supports & containment, MARLEY AQUATOWER cooling tower w/pumps, top platen
170,000 lbs, moving platen 74,000 lbs, bottom platen 134,000 lbs, hot plate 25,000
lbs, (8) columns 126,000 lbs, (4) main rams 108,000 lbs, (4) main cylinders 148,000
lbs, (4) jack rams & cylinders 28,000 lbs, simultaneous closing unit 10,000 lbs,
controls & electrics, approx 650 tons (located in Arcata)
LECKENBY caul transfer & recovery system including hydraulic caul turner, 13’ dia. x
27’ long, holds (17) cauls, (2) rough board side trim hogger saws, tangent type rotary
wicket lowering board cooler, 20’ dia. x 28’ long w/capacity of (32) boards, includes
all forming, mat & board conveyors, hydraulic units, drive controls & electrics, no caul
plates (located in Arcata)
Board Presses & Formers
1989 PATHEX 8400 ton, 8’x27’ single opening top pressure board press, (12) main
cylinders, (4) pull back cylinders, (6) columns, 8’ steel belt w/DC drive, outfeed chains
to vacuum stacker, BISON N1350M single head former w/infeed belt, mat saw,
pumps, piping, electrics & controls, approx. 300 tons (located in Crescent City, sold
by photo in Arcata)
PATHEX 7525 ton press, 8’x24’ window frame down stroke board press, (2)
2-3/4”x107”x300” platens, 109” wear plate, 12” daylight, (12) main cylinders, (4) pull
back cylinders, (6) columns, 105” steel belt w/DC drive, outfeed chains to vacuum
stacker, BISON traveling 3-head former, mat saw, pumps, piping, electrics & controls,
s/n: 4744, approx. 350 tons (located in Crescent City, sold by photo in Arcata)
SIEMPELKAMP 8’x16’ single opening board press, (8) main cylinders, (4) pull back
cylinders, (4) columns, 8’ steel belt w/DC drive, SIEMPELKAMP traveling 3-head
former, outfeed rolls & transfer to over end stacker, pumps, piping, electrics &
controls, approx. 225 tons (located in Crescent City, sold by photo in Arcata)
Refiners-Grinders
SPROUT WALDREN 45-1B gravity discharge refiner, 2000 hp/1785 rpm, 445 volt
(approx. 30,000 lbs) stainless steel disc, plates & internal parts, s/n: 74-1605 (located
in Arcata)
PALLMAN CENTRA SELECTOR PPSM14P refiner, 48” ring, TOSHIBA 250 hp impeller
ring drive, GE 25 hp refining ring drive, approx 9000 lbs, s/n: 8472011 (located in
Arcata)
PALLMAN PKSM12-600 refiner, spare not installed (located in Arcata)
(2) 2006 GRUENDLER 4024 ARISTOCRAT fine grinders, 40”x24” capacity, (8)
hammers per pocket, TECO 125 hp motor (s/n: 50048 located in Arcata; s/n: 50049
located in Crescent City, sold by photo in Arcata)
2006 GRUENDLER 4024 AFG fine grinder, 40”x24” capacity, (8) hammers per pocket,
TECO 125 hp motor, s/n: 500478 (located in Arcata)
GRUENDLER 24-40 PEERLESS grinder, 24”x40” capacity, MARATHON 125 hp motor,
s/n: 22689 (located in Arcata)
GRUENDLER 24-40 center feed grinder, 24”x40” capacity, BALDOR 125 hp motor, s/n:
21651 (located in Arcata)
Sizer-Hogs
JEFFREY 30 WBSS chip sizer/hammermill, 24”x21” rotor, 4-rows w/(10) hammers,
BALDOR Super E 150 hp motor, approx 3000 lbs, s/n: 886562 (located in Arcata)
JEFFREY 36”x48” Type B3 pulverizer/hammer hog, 30”x48” opening, 6-rows of (36)
hammers, AC 150 hp/1180 rpm motor, approx 14,600 lbs, s/n: 8919 (located in
Arcata)
JEFFREY 45WB hammer hog, 41”x27-1/2” opening, 32”x41” rotor, 6-rows of hammers,
GE 250 hp motor, approx 9880 lbs, s/n: 12395 (located in Arcata)
MONTGOMERY 34HD-60BH blo-hog, SIEMENS 100 hp motor, approx 15 tph bark,
approx 10,000 lbs, s/n: 1670 (located in Arcata)
MONTGOMERY blo-hog, TOSHIBA 150 hp motor, approx 10,000 lbs (located in Arcata)
CRESSWOOD EF72-100 grinder/board breaker, 72” arbor w/TOSHIBA 100 hp motor,
s/n: 1000995, EDEM 72”x20’ vibratory conveyor, 36”x60” scissor lift, 24”x24’ covered
paddle belt & 24”x30’ transfer belt (located in Crescent City, sold by photo in
Arcata)
Auctioneers note: A number of items are
located at the Hambro Forest Products
facility in Crescent City and will be sold by
photo at the Arcata auction site.