Washing Machine Перална машина - Blomberg

More documents

Recommendations

Info

7 Troubleshooting Programme cannot be started or selected. • Washing machine has switched to self protection mode due to a supply problem (line voltage, water pressure, etc.). >>> Press and hold Start / Pause button for 3 seconds to reset the machine to factory settings. (See "Canceling the programme") Water in the machine. • Some water might have remained in the product due to the quality control processes in the production. >>> This is not a failure; water is not harmful to the machine. Machine vibrates or makes noise. • Machine might be standing unbalanced. >>> Adjust the feet to level the machine. • A hard substance might have entered into the pump filter. >>> Clean the pump filter. • Transportation safety bolts are not removed. >>> Remove the transportation safety bolts. • Laundry quantity in the machine might be too little. >>> Add more laundry to the machine. • Machine might be overloaded with laundry. >>> Take out some of the laundry from the machine or distribute the load by hand to balance it homogenously in the machine. • Machine might be leaning on a rigid item. >>> Make sure that the machine is not leaning on anything. Machine stopped shortly after the programme started. • Machine might have stopped temporarily due to low voltage. >>> It will resume running when the voltage restores to the normal level. Programme time does not countdown. (On models with display) • Timer may stop during water intake. >>> Timer indicator will not countdown until the machine takes in adequate amount of water. The machine will wait until there is sufficient amount of water to avoid poor washing results due to lack of water. Timer indicator will resume countdown after this. • Timer may stop during heating step. >>> Timer indicator will not countdown until the machine reaches the selected temperature. • Timer may stop during spinning step. >>> Automatic unbalanced load detection system might C be activated due to the unbalanced distribution of the laundry in the drum. Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to its surrounding environment. Laundry should be rearranged and re-spun. Foam is overflowing from the detergent drawer. • Too much detergent is used. >>> Mix 1 tablespoonful softener and ½ l water and pour into C the main wash compartment of the detergent drawer. Put detergent into the machine suitable for the programmes and maximum loads indicated in the “Programme and consumption table”. When you use additional chemicals (stain removers, bleachs and etc), reduce the amount of detergent. Laundry remains wet at the end of the programme • Excessive foam might have occurred and automatic foam absorption system might have been C A activated due to too much detergent usage. >>> Use recommended amount of detergent. Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to its surrounding environment. Laundry should be rearranged and re-spun. If you cannot eliminate the problem although you follow the instructions in this section, consult your dealer or the Authorized Service Agent. Never try to repair a nonfunctional product yourself. 24 - EN
"Close door" warning is displayed. Loading door might be ajar. >>> Open and close the loading door again. Make sure that it is tightly closed. Machine will start operating. "No water" warning is displayed. There might be no water supplied to the machine or the water pressure may be low. >>> Check your taps and connection hoses. If there is no problem in water pressure or supply, restart the machine by pressing Start / Pause button. "aquAvoid+" warning is displayed. Overflow float might be active and have switched the machine to protection mode. >>> Call the Authorised Service Agent. "Clean pump" warning is displayed. Machine might not be capable to drain the water. >>> Clean the pump filter. Check to make sure that the drain hose is not folded or blocked. For detailed information, see "Maintenance and cleaning". 25 - EN 2820522325.EN/241011.1847
Page 1 and 2: Washing Machine Перална ма
Page 3 and 4: 2 Installation Refer to the nearest
Page 5 and 6: the fuse or breaker in the house is
Page 7 and 8: • Do not use amounts exceeding th
Page 9 and 10: 4 Operating the product Control pan
Page 11 and 12: Many clothes are correctly detected
Page 13 and 14: C A Do not load more than 1 double
Page 15 and 16: Programme and consumption table EN
Page 17 and 18: the selected programme is also disp
Page 19 and 20: change in the screen brightness. Fa
Page 21 and 22: 5 Maintenance and cleaning Service
Page 23: 6 Technical specifications C C Mode
Page 28 and 29: 2 Монтаж За монтажа
Page 30 and 31: електротехник да м
Page 32 and 33: • При ползване на п
Page 34 and 35: Съвети за ефективн
Page 36 and 37: C Програмите са с ог
Page 38 and 39: Следващата таблица
Page 40 and 41: Леко замърсени Изп
Page 42 and 43: C Допълнителните фу
Page 44 and 45: • Ако машината не п
Page 46 and 47: Програма Степен на
Page 48 and 49: Издърпайте маркуча
Page 50 and 51: 7 Възможни решения

Washing Machine Перална машина - Blomberg

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?