Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>Okatmos®</strong> <strong>star</strong> <strong>110</strong><br />
Technical Data Sheet<br />
Okatmos ® <strong>star</strong> <strong>110</strong><br />
Wet-bed adhesive<br />
. fibre-reinforced<br />
. short intitial tack<br />
. excellent coverage rate<br />
. easy to spread<br />
. anti-microbial<br />
P R O P E R T I E S A N D U S A G E<br />
Solvent-free, very low emission, fibre-reinforced wet-bed dispersion adhesive for adhering rubber floor coverings<br />
of up to 4.0mm thickness in sheet and tile format, designer coverings in plank and tile format and for<br />
homogeneous/heterogeneous PVC floor coverings. The addition of reinforcing fibres minimises adhesive<br />
squeeze during installation and residual indentation in installed flooring.<br />
Thanks to its anti-microbial properties, <strong>Okatmos®</strong> <strong>star</strong> <strong>110</strong> also helps to prevent VOC odours.<br />
S U B S T R A T E P R E P A R A T I O N<br />
The substrate must be inspected in accordance with the current relative installation standard and be ready for<br />
installation. Substrates should be free of all surface contaminates and should not exceed 75% RH on an<br />
electrical hygrometer using in-situ probes. If the substrate surface is outside of the acceptable smoothness<br />
and planeness standards, an appropriate Kiesel primer and levelling compound should be used to rectify.<br />
If only minimal substrate preparation is required, it is recommended to first prime the substrate with Kiesel<br />
EG20 primer diluted 1:2 ratio with water and applied using a soft broom. Ensuring to broom out any puddling<br />
or pooling, once the EG20 is dry and not tacky (approx 30mins) it is ready to install over. Priming the surface<br />
of the substrate will ensure an even initial tack time giving an optimum wet transfer of adhesive to the covering.<br />
P R O C E S S I N G<br />
Stir <strong>Okatmos®</strong> <strong>star</strong> <strong>110</strong> well before use. Apply the adhesive to the substrate using the toothed strip attached<br />
to the lid. Only apply as much to the surface as can be covered within the stated laying time. The toothed<br />
strip should be replaced in good time (approx. every 15-20m²) before gaps appear between the fibres and to<br />
ensure that the correct amount of adhesive is applied at all times. After the initial tack time (depending on the<br />
internal climate conditions), lay the floor covering in the adhesive bed while still wet, being careful not to<br />
trap any air, and rub on carefully. After approximately 30 minutes, rub or roll over the covering again. Ensure<br />
that the rear side of the covering is sufficiently wet. The floor covering must be tension-free and lie flat.<br />
Weigh down if necessary. Avoid bulging in the area of seams and upwardly projecting building components.<br />
Wait at least 24 hours before sealing joints or welding seams in the floor covering. The laying instructions of<br />
the manufacturer of the floor covering are to be heeded at all times.<br />
Kiesel Bauchemie GmbH u. Co. KG<br />
Wolf-Hirth-Stra3e 2 D-73730 Esslingen<br />
Telefon: 0711 93134-0<br />
Telefax: 0711 93134-140<br />
www.kiesel.com<br />
Niederlassung:<br />
Otto-Kiesel-Stra3e<br />
D-39590 Tangermünde<br />
Telefon: 039322 95-0<br />
Telefax: 039322 95-100<br />
Geschäftsführer:<br />
Wolfgang Kiesel<br />
Dr. Matthias Hirsch<br />
Pers. haft. Gesellschafterin:<br />
Kiesel Verwaltungsges. mbH<br />
Amtsgericht<br />
Stuttgart HRB 210484<br />
Sitz der Gesellschaft:<br />
73730 Esslingen<br />
Amtsgericht<br />
Stuttgart HRA 210806
<strong>Okatmos®</strong> <strong>star</strong> <strong>110</strong>- Page 2 of 2<br />
S P E C I F I C A T I O N S<br />
Color Cream white<br />
Application Interior floors<br />
Suitable for chair castors<br />
(DIN EN 12 529)<br />
Suitable<br />
Minimum floor temperature + 10°C (substrate)<br />
Initial tack time* Approx. 5-10 minutes<br />
Processing time* Approx. 20 minutes<br />
Ready for foot traffic* After approx. 24 hours<br />
Final strength* After approx. 72 hours<br />
Floor heating systems Suitable<br />
Marked according to<br />
GefStoffV regulations<br />
Not classified<br />
GISCODE D 1 acc. To TRGS 610<br />
EMICODE EC (GEV)<br />
Shelf live store in frost protected area for up to 12 months<br />
* At +20°C und 65 % relative humidity<br />
Higher temperatures and lower humidity decreases, lower temperature and high humidity increase this<br />
value respectively.<br />
T O O L S A N D C O V E R A G E<br />
Tooth type Type of floor covering Consumption<br />
TKB A2 Rubber floor coverings of 2-4mm 250-280g/m² approx.<br />
thickness in lengths and tiles with<br />
polished rear side<br />
TKB A2 Designer coverings in plank and 250-280g/m² approx.<br />
tile format<br />
TKB A2 homogeneous/heterogeneous 250-280g/m² approx.<br />
C L E A N I N G<br />
Clean tools with water immediately after usage.<br />
P A C K A G I N G<br />
Packaging Product Code<br />
33 x 14 kg plastic buckets 49065<br />
The information is based on out experience and is to be regarded as general instructions. We cannot guarantee<br />
successful results since we do not have any influence on the conditions at the construction site and the proper<br />
processing. In any case a sample application is recommened before the installation.<br />
This data sheet replaces any previously issued data sheet.<br />
23.10.10 Wbg.
Change language