RM360 RM460 RM660 RM760 Service Manual - WebRing Inc.

More documents

Recommendations

Info

CABINET ADJUSTMENTS To change door panel The refrigerator is normally delivered without door panel(s). Before starting the mounting work check that the panel dimensions are in compliance with those given in the table and read the instructions through. When mounting the panel, proceed as follows: 1. 2. 3. 4. 5. 6. Remove the top decoration strip (2) with two screws (1). its Insert one of the vertical edges of the panel into the groove of the door frame (3). Bend the panel gently so that the free side of the panel can be slipped into the corresponding groove of the door frame (4). Push the panel downwards so that the lower horizontal edge of the panel is fitted into the bottom groove (5). Between the upper edge of the panel and the door frame there is now a gap which should be covered by the decoration strip. Put the strip across the door so that the gap is covered and push it upwards (6). The tabs on the inside of the strip should fit in behind the flange of the door frame. Secure the decoration strip by means of the two screws (1). Panel dimensions Thickness max. 5/32" Height Width Type Max. Min. Max. Min. RM 360 636 633 516,5 513,5 mm 25" 24 7/8" 20 11/32" 20 7/32"inch RM 460 679 676 550,5 547,5 26 23/32" 26 19/32" 21 11/16" 21 9,16":ch RM 660 879 876 550,5 547,5 mm 34 5/8" 34 l/2" 21 11/16" 21 9/16"inch RM 760 288 285 550,5 547,5 mm upper 11 11/32" 11 7/32" 21 11/16" 21 9/16"inch RM 760 801 798 550,5 547,5 mm lower 31 17/32" 31 13/32" 21 11/16" 21 9/16"inch Fig.8 a
9 Replacement of door gasket (Fig. 9) 1. Pull the old gasket out from the door frame. 2. Make sure that no gasket parts are left in the groove. 3. Beginning in one of the corners, fit the new gasket by pressing it into the groove. Reversing outer door (Fig. 10) 1. Remove the plastic cover (1) by loosening the screws (2) underneath. 2. Remove the upper hinge pin (3). 3. Remove the door and move the lower hinge pin (4) to the other side. 4. Fit the door and press the upper hinge pin (3) into the adequate hole. For two-door refrigerators the middle hinge and the travel latch should change position. Replacement of evaporator door on RM360, RM460, RM660 (Fig. 11 and 12) 1. 2. 3. 4. 5. Pry the spring housings (B) away from the lining so that it snaps out and turn the spring housing downwards 180'. Push the carrier (A) inwards by means of a blunt mandrel or pin and remove the shutter. Mount the new shutter in close position first on one side, making sure that the cross slots engage in the cross on the hinge plate (C). Press the carrier on the opposite side so that the hinge plate on the shutter can be pushed over it. See that the crosses engage. Turn the spring housing round and up until the small tag (D) snaps into the slot into the lining. Fig.9 Fig.10 Fig.11 Fig.12
Page 1 and 2: United States SALES OFFICES DOMETIC
Page 3 and 4: 3 INSTALLATION ELECTRICAL CONNECTIO
Page 5 and 6: 5 CLEARANCES Minimum clearances in
Page 7: 7 be stored in the frozen food stor
Page 11 and 12: 11 the room temperature at the time
Page 13 and 14: 13 THE GAS/ELECTRIC EQUIPMENT Gas e
Page 15 and 16: 15 DISASSEMBLY OF BURNER JET AND BU
Page 17 and 18: 17 200 7390 N L 12VOLTS DC @ GREEN

RM360 RM460 RM660 RM760 Service Manual - WebRing Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?