ETA130190 IM PURE ETA 1 - ETA-Danmark

More documents

Recommendations

Info

Page 2 of 24 pages of European Technical Approval no. ETA-13/0190 I LEGAL BASIS AND GENERAL CONDITIONS 1 This European Technical Approval is issued by ETA-Danmark A/S in accordance with: - Council Directive 89/106/EEC of 21 December 1988 on the approximation of laws, regulations and administrative provisions of Member States relating to construction products 1 , as amended by Council Directive 93/68/EEC of 22 July 1993 2 . - Bekendtgørelse 559 af 27-06-1994 (afløser bekendtgørelse 480 af 25-06-1991) om ikrafttræden af EF direktiv af 21. december 1988 om indbyrdes tilnærmelse af medlemsstaternes love og administrative bestemmelser om byggevarer. - Common Procedural Rules for Requesting, Preparing and the Granting of European Technical Approvals set out in the Annex to Commission Decision 94/23/EC 3 . - ETAG 001 - Guideline for European Technical Approval of metal anchors for use in concrete – Part 5: Bonded anchors 2 ETA-Danmark A/S is authorized to check whether the provisions of this European Technical Approval are met. Checking may take place in the manufacturing plant. Nevertheless, the responsibility for the conformity of the products to the European Technical Approval and for their fitness for the intended use remains with the holder of the European Technical Approval. 3 This European Technical Approval is not to be transferred to manufacturers or agents of manufacturers other than those indicated on page 1, or manufacturing plants other than those indicated on page 1 of this European Technical Approval. 1 Official Journal of the European Communities N o L40, 11 Feb 1989, p 12. 2 Official Journal of the European Communities N o L220, 30 Aug 1993, p 1. 3 Official Journal of the European Communities N o L 17, 20 Jan 1994, p 34. 4 This European Technical Approval may be withdrawn by ETA-Danmark A/S pursuant to Article 5(1) of Council Directive89/106/EEC. 5 Reproduction of this European Technical Approval including transmission by electronic means shall be in full. However, partial reproduction can be made with the written consent of ETA-Danmark A/S. In this case partial reproduction has to be designated as such. Texts and drawings of advertising brochures shall not contradict or misuse the European Technical Approval. 6 This European Technical Approval is issued by ETA-Danmark A/S in English. This version corresponds fully to the version circulated within EOTA. Translations into other languages have to be designated as such.
Page 3 of 24 pages of European Technical Approval no. ETA-13/0190 II SPECIAL CONDITIONS OF THE EUROPEAN TECHNICAL APPROVAL 1 Definition of product and intended use The IM PURE ETA 1 is a bonded anchor (injection type) consisting of an injection mortar cartridge using an applicator gun equipped with a special mixing nozzle and threaded anchor rod of the sizes M8 to M30 made of galvanized carbon steel or stainless steel A4-70 or A4- 80: 1.4401, 1.4404, 1.4571 or high corrosion resistant stainless steel A4-70: 1.4529, 1.4565, 1.4547 with hexagon nut and washer. The threaded rod is placed into a drilled hole previously injected with a mortar with a slow and slight twisting motion. The anchor rod is anchored by the bond between rod, mortar and concrete. The threaded rod is available for all diameters with three type of tip end: a one side 45° chamfer, a two sided 45° chamfer or a flat. The threaded rods are either delivered with the mortar cartridges or commercial standard threaded rods purchased separately. The mortar cartridges are available in different sizes: 265 ml, 475 ml and 900 ml. The anchors are intended to be used with embedment depth given in Annex 2,Table 1. For the installed anchor see Figure given in Annex 1. Intended use The anchors are intended to be used for anchorages for which requirements for mechanical resistance and stability and safety in use in the sense of the Essential Requirements 1 and 4 of Council Directive 89/106/EEC shall be fulfilled and failure of anchorages made with these products would compromise the stability of the works, cause risk to human life and/or lead to considerable economic consequences. Safety in the case of fire (Essential Requirement 2) is not covered by this ETA. The anchors are to be used only for anchorages subject to static or quasi-static loading in reinforced or unreinforced normal weight concrete of strength class C20/25 at minimum to C50/60 at maximum according to EN 206-1. The anchors may be anchored in cracked (M12 to M24) or non-cracked concrete (M8 to M30). The anchors may be installed in dry or wet concrete (use category 1) or in flooded holes with the exception of seawater (use category 2). All the diameters (from M8 to M30) may be used overhead. The anchors may be used in the following temperature range: a) -40°C to +40°C (max. short term temperature +40°C and max. long term temperature +24°C), b) -40°C to +80°C (max. short term temperature +80°C and max. long term temperature +50°C). Elements made of galvanized steel may be used in structures subject to dry internal conditions only. Elements made of stainless steel may be used in structures subject to dry internal conditions and also in concrete subject to external atmospheric exposure (including industrial and marine environment) or exposure in permanently damp internal conditions if no particular aggressive conditions exist. Such particular aggressive conditions are e.g. permanent, alternating immersion in seawater or the splash zone of seawater, chloride atmosphere of indoor swimming pools or atmosphere with extreme chemical pollution (e.g. in desulphurization plants or road tunnels where de-icing materials are used). Elements made of high corrosion resistant steel may be used in structures subject to dry internal conditions and also in concrete subject to external atmospheric exposure or exposure in permanently damp internal conditions or in other particular aggressive conditions. Such particular aggressive conditions are e.g. permanent, alternating immersion in seawater or the splash zone of seawater, chloride atmosphere of indoor swimming pools or atmosphere with chemical pollution (e.g. in desulphurization plants or road tunnels where de-icing materials are used). Assumed working life The provisions made in this European Technical Approval are based on an assumed intended working life of the anchor of 50 years. The indications given on the working life cannot be interpreted as a guarantee given by the producer or Approval Body, but are to be regarded only as a means for choosing the right products in relation to the expected economically reasonable working life of the works.
Page 1: ETA-Danmark A/S Kollegievej 6 DK-29
Page 5 and 6: Page 5 of 24 pages of European Tech
Page 11 and 12: Table 2: Threaded rod materials Par
Page 13 and 14: Page 13 of 24 pages of European Tec
Page 17 and 18: 1 2 3 4 5 6 Page 17 of 24 pages of

ETA130190 IM PURE ETA 1 - ETA-Danmark

Create successful ePaper yourself

Delete template?

Save as template?