LAK DC Motors - T-T Electric
LAK DC Motors - T-T Electric
LAK DC Motors - T-T Electric
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Application data<br />
Standards<br />
IEC 600341<br />
Insulation<br />
Class H<br />
Temperature rise<br />
Frames 112180: Class F<br />
Frames 200280: Class H<br />
Vibration class and balance<br />
<strong>LAK</strong> 4000 motors follow IEC<br />
6003414 with vibration class A<br />
as standard . Grade B is available<br />
on request . The motors are balanced<br />
with half key as standard .<br />
Overload capacity<br />
<strong>LAK</strong> 41124280:<br />
1 .6 x FLT for 15 sec . every 5<br />
minutes<br />
1 .8 x FLC for 30 sec . every 30<br />
minutes<br />
Terminal box position<br />
<strong>LAK</strong> 41124180:<br />
Standard: On right side of the<br />
motor (facing dend) .<br />
Mounting of terminal box on top<br />
or left side on request .<br />
<strong>LAK</strong> 42004280:<br />
Standard: On top of the motor .<br />
Mounting of terminal box on<br />
either side of the motor on<br />
request .<br />
Blower position<br />
Standard: On top of the motor at<br />
the nondrive end .<br />
Other positions on request .<br />
Blower is supplied without filter<br />
as standard .<br />
Filter on request .<br />
Bearings<br />
Grease lubricated ball bearings<br />
on Dend as standard .<br />
For belt drive please contact our<br />
sales offices .<br />
Painting<br />
The standard <strong>LAK</strong> surface finish<br />
has excellent corrosion<br />
resistance properties . The<br />
standard colour of <strong>LAK</strong> motors is<br />
blue according to Munsell 8B<br />
4 .5/3 .25 (similar to RAL 5024) .<br />
Heat exchangers<br />
Air/water (IC86W):<br />
Air/water exchangers are especially<br />
recommended for polluted<br />
environment .<br />
Standard is for clean water .<br />
For corrosive water, please<br />
contact TT <strong>Electric</strong> .<br />
Position on top of the motor<br />
as standard . Water connection<br />
flanges at right hand side<br />
(facing Dend) .<br />
Max . water pressure 10 PSI<br />
Max . inlet water temperature<br />
25°C . A water temperature rise<br />
of 810°C must be expected .<br />
<strong>LAK</strong> 41324180:<br />
Fan motor at Nend .<br />
<strong>LAK</strong> 42004280:<br />
Fan motor at Dend .<br />
A constant speed fan circulates<br />
the internal cooling air . A polyamide<br />
filter is provided to prevent<br />
circulation of carbon dust .<br />
For motors with low loads or a<br />
low incoming water temperature,<br />
a temperature regulator is<br />
recommended to avoid condensation<br />
in the cooling air circuit<br />
and to minimize water consumption<br />
.<br />
6<br />
Air/air (IC666):<br />
Detailed heat exchanger information on request.<br />
Air/air heat exchangers are<br />
recommended where water is<br />
not available for cooling purposes<br />
.<br />
The output of a motor with air/air<br />
exchanger will be approximately<br />
20% lower compared to cooling<br />
forms IC06/17/37/86W .<br />
<strong>LAK</strong> 41324280:<br />
Position: On top of the motor as<br />
standard .<br />
Two constant speed fans at top<br />
of the heat exchanger to provide<br />
air circulation for the outer and<br />
inner circuits .<br />
A polyamid filter is provided to<br />
prevent circulation of carbon<br />
dust .