Coating Thickness Gage - ThomasNet

More documents

Recommendations

Info

For the non-destructive measurement of non-magnetic coatings (paint, enamel, galvanizing, metalizing, plating, etc.) on STEEL ACCURATE ■ Certificate of Calibration showing traceability to N.I.S.T. included with every gage ■ Matching Calibration Standards and Procedures available for every model ■ Highly wear resistant Carbide Probe for longest life and continuous accuracy ■ Remove center of dial cover for easy calibration adjustment ■ Conforms to national and international standards DURABLE ■ Extra rugged housing, not affected by mechanical shock, water, acid or solvents ■ Unique overall design, fully supported, positive positioning, no pivoting tendencies during measurement ■ Can be used fully supported or with only the front probe area contacting the surface ■ Functions on a permanent rare-earth cobalt magnet ■ No batteries/electronics ■ 2 year warranty EASY TO USE ■ Positive visual and audible indicators to designate when thickness reading is established ■ “V” grooves in probe housing and Gage base allow correct positioning on cylindrical objects ■ Compact, lightweight, precisely balanced, independent of gravity – can be used in any position ■ GO/NO-GO button can be pre-set for rapid measurement ■ Probe contact and dial rotation all in a one-finger operation ■ Furnished with wrist strap and instructions in a high quality leather case with belt loops for your convenience Carbide measuring probe for long life. FOR: Hot dip galvanizing, hard chrome metalizing, paint, enamel coatings on steel Scale FM 0–80 mils Tolerance: ± 0.2 mils up to 4 mils ± 5% of the reading over 4 mils Scale F 0–2000 microns Tolerance: ± 5 microns up to 100 microns ± 5% of the reading over 100 microns The Measure of Quality Accurate & Dependable FOR: Electroplating, thin paint films, phosphating on steel Scale GM 0–8 mils Tolerance: ± 0.04 mils up to 0.8 mils ± 5% of the reading over 0.8 mils Scale G 0–200 microns Tolerance: ± 1 micron up to 20 microns ± 5% of the reading over 20 microns DEFELSKO CORPORATION 802 Proctor Ave., Ogdensburg, NY 13669 USA Toll Free 1-800-448-3835 Phone: +1-315-393-4450 Fax: +1-315-393-8471 E-mail:techsale@defelsko.com Web: www.defelsko.com ©DeFelsko Corporation USA 2010 •All Rights Reserved • Technical Data subject to change without notice •Printed in U.S.A. •PT.FM-GM.v.LW-W1005
Measures non-magnetic coatings such as paint, enamel, plating, hot-dip galvanizing on steel. Ideal for measuring on small, hot or hard-to-reach surfaces. PosiPen ® Coating Thickness Gage
Page 1 and 2: DeFelsko ® Catalog - Fall 2012 Coa
Page 3 and 4: WiFi Coating Thickness Gages for AL
Page 5 and 6: Rugged Features... Sealed USB Port
Page 7 and 8: Coating Thickness Gage Ideal for...
Page 9: Accurate & Dependable For the non-d
Page 13 and 14: Advanced models measure up to 3 lay
Page 15 and 16: Rugged Features... Sealed USB Port
Page 17 and 18: Non-contact Uncured Powder Thicknes
Page 19 and 20: PosiTest ® Pull-Off Adhesion Teste
Page 21 and 22: PosiTest ® AT-M Manual Adhesion Te
Page 23 and 24: WiFi Ideal for Use Outdoors & Indoo
Page 25 and 26: Tough Features... Sealed USB Port f
Page 27 and 28: Ultrasonic Thickness Gage The Measu
Page 29 and 30: Tough NEW Features Sealed USB port
Page 31 and 32: The Measure of Quality WiFi Measure
Page 33 and 34: PosiTector Inspection Kits Each Ins
Page 35 and 36: Certified coating thickness standar
Page 37: DeFelsko Corporation, a U.S. manufa

Coating Thickness Gage - ThomasNet

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?