OM, Gardena, Submersible Pressure Pump, Art 01479-20, 2007-02

More documents

Recommendations

Info

3. Initial Operation Connecting the hose: Tie the fastening rope to the pump: 4. Operation 4 Thermal motor protector 1 2 3 2 When connecting the pump to the water supply system, the country-specific sanitary regulations must be observed to prevent water not of drinking water quality being drawn back in. ➔ If necessary, contact your sanitary expert. The pump is automatically switched off on overheating by the built-in thermal motor protector. After having cooled down, the motor automatically switches on again (see 6. Trouble- Shooting). The pump fitting is equipped with a 33,3 mm (G 1”) thread to which 13 mm (1/2”), 19 mm (3/4”) and 15 mm (5/8”) hoses can be connected by using GARDENA hose connection system fittings. 1. Screw the pump fitting 1 onto the outlet of the pump and tighten it manually until the washer fits closely. 2. Attach the hose to the pump fitting 1. Best results in delivery capacity of the pump are achieved when using 19 mm (3/4”) hoses in conjunction with GARDENA “Profi” Maxi-Flow System fittings (e.g. Art. No. 1752) or 25 mm (1”) hoses with fittings available at your sanitary dealer. When connecting simultaneously several hoses/accessories, we recommend to use either our GARDENA Twin-Tap Connector or our Four Channel Water Distributor (Art. No. 1210/1194) which can be directly screwed onto the pump fitting 1. v Fasten the fastening rope 2 to the loop 3 for fastening rope. To ensure that the pump draws the water out, the water to be drained must be at least 20 cm deep. 1. Submerge the pump in the well or other water reservoirs, using the fastening rope 2. In order to avoid contaminations, the pump should not be placed directly on the ground. It must hang freely min. 30 cm above ground. 2. Secure the fastening rope 2. 3. When using the pump in deep wells or shafts (ot more than approx. 5 m), the power cable 4 is to be guided by means of clamps alongside the fastening rope 2. 4. Plug the power cable 4 into a mains socket. 11 GB
GB 5. Cleaning Cleaning the inlet sieve and suction base: 6. Trouble-Shooting 12 5 6 The pumps are virtually maintenance-free. Warning! Electric shock! A Risk of injury due to electric shock. V Disconnect the pump from the mains before cleaning the suction base. 1. Press in the 3 rear catches 5 (e.g. using a screwdriver) and pull the lower part of the suction base 6 off the pump. 2. Clean the suction base and inlet sieve. 3. Push the lower part of the suction base 6 with the inlet sieve back onto the pump until the 3 rear catches 5 snap into place. For safety reasons a damaged turbine can only be exchanged by the GARDENA Service Centre. Problem Probable cause Remedy Pump is running, Air cannot escape, since v Open pressure line but doesn’t deliver. pressure line is closed. (e. g. kinked pressure pipe). Air locks in the suction base. v Wait for max. 60 seconds until the pump deaerates automatically over the vent valve. If necessary, switch off and start it again. Suction base is clogged. v Disconnect plug and clean suction base (see 5. Cleaning). When starting the pump, water height falls below the min. water level. v Submerge pump deeper. Pump doesn’t start or Thermal overload switch has v Disconnect plug and clean suddenly stops during switched the pump off due suction base (see 5. Cleanoperation. to overheating. ing). Observe max. media temperature of 35 °C. No power. v Check fuses and electric connections. Dirt particles are jammed v Disconnect plug and clean in the suction base. suction base (see 5. Cleaning). Pump runs, but output Suction base is clogged. v Disconnect plug and clean suddenly decreases. suction base (see 5. Cleaning).
Page 1 and 2: ® GARDENA D Gebrauchsanweisung Tau
Page 3: GB 10 In Austria In Switzerland Mai
Page 7 and 8: F 9. Service Warranty Product Liabi

OM, Gardena, Submersible Pressure Pump, Art 01479-20, 2007-02

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?