Catalog

More documents

Recommendations

Info

Insulation Fixings F27CF Solid Materials Ref. Insulation anchors for hard insulation GLASS FIBRE REINFORCED PLASTIC NAIL UP TO 160 MM THICK INSULATION Agrément Technique Européen Applications Anchoring of hard insulation (polystyrene, extruded polystyrene panels) panels up to 160 mm thick in concrete, solid brick and cellular concrete. Type of installation Push-through installation. Description • Glass fi bre reinforced polyamide expansion nail. • Polypropylene plug body. • The plug expands when the nail is hammered in. • The plug's zig-zag segments mechanically lock in the substrate material. Benefits • European Technical Approval. • Quick and easy installation through the insulation using a hammer. • The plug's design guides the screw during its installation and prevents premature expansion and crushing of the insulation. • Grainy nail head surface for better adherence. • Anchors insulation up to 160 mm thick. Advice • It is important to comply with the technical installation data. • Do not install the plug and the nail in a single operation. • Do not insert the plug and in particular its disk into the insulation by tapping too hard on it. (**) (**) **Data p. 87 Qty Ø L Ref. EAN CU Pack 200 10 70 F27010070000CF 3336600161993 1 box 200 10 90 F27010090000CF 3336600162006 1 box 200 10 110 F27010110000CF 3336600162013 1 box 200 10 120 F27010120000CF 3336600162020 1 box 200 10 140 F27010140000CF 3336600162037 1 box 200 10 160 F27010160000CF 3336600162044 1 box 200 10 180 F27010180000CF 3336600162051 1 box 200 10 200 F27010200000CF 3336600162068 1 box 86
Applications Insulation disk for flexible insulation Anchoring of mineral wool and other fl exible insulation in solid brick, hollow brick, block and cellular concrete. Description • Used with ref. F28CM. • Improves the structure's rigidity. • Protects the insulating material from damage. Ref. F27 Hollow and Solid Materials * *With ref. F28CM Agrément Technique Européen Qty Ø Ref. EAN CU Pack 200 140 F27140000000XX 3336600161887 1 box A - Concrete class C12/15 to C50/60 B - Full brick and silicate brick C - Slab or refractory brick D - Lightweight concrete LAC 2 to 25 E - Cellular concrete Concrete C12/15 to C50/60 in accordance with EN-206-1 Full brick in accordance with EN-771-1 Refractory brick in accordance with PN-B-12011:1997 Breeze block class 10 in accordance with PN-EN 771-3 Cellular concrete type 600 in accordance with PN-EN 774-1 *Non protected by the technical agrement **Without standards, security toothing factor is m=2,0 Ref.F28CF Ref.F28CM Ref.F27CF 10x140 10x160 10x180 10x200 10x220* 10x260* 10x300* 10x140 10x160 10x180 10x200 10x220* 10x260* 10x300* 10x70 10x90 10x110 10x120 10x140 10x160 10x180 10x200 10x220* 10x260* Diamètre du trou de forage Diameter of drill bit d 0 mm 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 Diamètre du clou Diameter of the pin d S mm 5,3 5,3 5,3 5,3 5,3 5,3 5,3 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 5,5 Longueur du clou Length of the pin L S mm 140 160 180 200 220 260 300 145 165 185 205 225 265 305 75 95 115 125 145 160 185 205 225 265 Profondeur d'ancrage effective Minimum effective anchorage depth h ef min mm 80 80 80 80 80 80 80 80 80 80 80 80 80 80 50 50 50 50 50 50 50 50 50 50 Profondeur du trou de forage Minimum hole depth h 1 min mm 90 90 90 90 90 90 90 90 90 90 90 90 90 90 60 60 60 60 60 60 60 60 60 60 Epaisseur de l'isolation à fixer Maximum working length t fix mm 60 80 100 120 140 180 220 60 80 100 120 140 180 220 30 50 60 80 100 120 140 160 180 220 Diamètre du disque de serrage Diameter of plate holder d p mm 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 Béton C12/25 Concrete C12/15 Caratéristiques** résistance à la charge (kN) Characteristics** resistance to tension loads (kN) Béton C16/20 Concrete C16/20 Béton C20/25 Concrete C20/25 Béton C50/60 Concrete C50/60 Brique pleine Full brick Brique réfractaire Refractory brick Brique creuse Horizontally perforated brick Béton cellulaire Aerated concrete Parpaing Breeze block Catégories d'usage Usage category Agrément technique Technical approval - - - - 0.6 0.5 - - - B,C ETA 06/0105 - - - - 0.7 0.7 - - - 0.6 0.75 0.75 0.75 0.6 - - 0.3 0.5 B,C A,B,D,E ETA 06/0105 ETA 08/0172 1- In the base material and in the insulation, drill a hole from diameter d 0 , from min. h 1 depth, according to the technical data thereby. 2- Clean the hole. 3- Put handly the insulation fixing. Do not use any tools. 4- Hammer the Diager Retaining Disc through the insulation board directly into the substrate, until the disc is pressed flush against the rigid foam board. BE CAREFUL!! Do not place the insulation fixing and the disc at the same time. And especially not the disc in the insulating materials by pushing too hard on it. 87
Page 1:
www.diager.com DRILLING & FIXING Ca
Page 4 and 5:
Innovation For Diager, Innovation i
Page 6 and 7:
PAGE PAGE Concrete - Hammer Carbide
Page 8 and 9:
Materials Masonry Diamond Tools 1/2
Page 10 and 11:
P A T E N T E D Concrete drill bit
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Concrete drill bit Ref. 166 LONGER
Page 20 and 21:
Page 22 and 23:
Concrete drill bit Power-Max Hammer
Page 24 and 25:
Accessories Ref. 120K 121K 124K 125
Page 26 and 27:
Tools for hammer drills Ref. 322 32
Page 28 and 29:
Selecting tools DRILLING STAND DIAM
Page 30 and 31:
Diamond core bit Ref. 435 Standard
Page 32 and 33:
Drilling motors Ref. 349H Diamond e
Page 34 and 35:
Diamond core bit Ref. 426 Glaze - S
Page 36 and 37:
Trépan Carbure Carbide core bit Ca
Page 38 and 39: Drilling in hollow brick In partner
Page 40 and 41: Masonry drill bit Ref. 226 MEGA Des
Page 42 and 43: Specific Ref. 215 MULTIMATERIALS De
Page 44 and 45: Specific Ref. 400 Glass & tile dril
Page 46 and 47: Wood drill bit Ref. 912 913 941 942
Page 48 and 49: Forstner bit Ref. 933 Forstner Clas
Page 50 and 51: Wood drill bit Ref. 910 Pro drill b
Page 52 and 53: HSS drill bit Ref. 731 700 DIN 338
Page 54 and 55: HSS drill bit Ø Max 12.7 Ref. 729
Page 56 and 57: HSS drill bit Ref. 769 750 Standard
Page 58 and 59: Forets Metal drill Métal bit Ref.
Page 60 and 61: Screwdriver bit Ref. 621PL 620PH 62
Page 62 and 63: Holesaws Ref. 650 HSS-E 8 % Co 8% C
Page 64 and 65: Sets range Concrete Hammer drill 07
Page 66 and 67: Fastening & Fixing Guide Chemical F
Page 68 and 69: Chemical Fixings Ref. F35V Hollow a
Page 70 and 71: Chemical Fixings Ref. F35ME Turbo m
Page 72 and 73: Heavy Duty Fixings Solid Materials
Page 74 and 75: Heavy Duty Fixings F37TH F37TH F37P
Page 76 and 77: General Fixings F50NY Solid Materia
Page 78 and 79: General Fixings Ref. F61 Hollow and
Page 80 and 81: General Fixings PATENTED 3-SECTION
Page 82 and 83: Frame Fixings F06NY Solid Materials
Page 84 and 85: Frame Fixings Ref. F55TH Hollow and
Page 86 and 87: Insulation Fixings Ref. F28CF Hollo
Page 90 and 91: Specific Fixings Sanitary installat
Page 92 and 93: MERCHANDISING, attract, seduce, and
Page 94 and 95: THE CLOTHING RANGE, kit yourself ou
Page 96 and 97: SUCCESS LIES IN STRONG PARTNERSHIPS
Page 98 and 99: Terms and conditions of sale DIAGER
Page 100: DRILLING &FIXING Rue Henri Moissan
show all

Catalog

Create successful ePaper yourself

Delete template?

Save as template?