Download File (1.01 MB) - Tektronix

More documents

Recommendations

Info

Data Sheet Electrical Sampling Module Characteristics (Cont.) Module Vertical Sensitivity Range DC Vertical Voltage Accuracy, Single Point, within ±2 °C of Compensated Temperature 80E10 10 mV to 1.0 V full scale ±[2 mV + 0.007 (Offset) + 0.02 (Vertical Value – Offset)] 80E09 10 mV to 1.0 V full scale ±[2 mV + 0.007 (Offset) + 0.02 (Vertical Value – Offset)] 80E08 10 mV to 1.0 V full scale ±[2 mV + 0.007 (Offset) + 0.02 (Vertical Value – Offset)] 80E07 10 mV to 1.0 V full scale ±[2 mV + 0.007 (Offset) + 0.02 (Vertical Value – Offset)] 80E06* 26 10 mV to 1.0 V full scale ±[2 mV + 0.007 (Offset) + 0.02 (Vertical Value – Offset)] 80E04 10 mV to 1.0 V full scale ±[2 mV + 0.007 (Offset) + 0.02 (Vertical Value – Offset)] 80E03 10 mV to 1.0 V full scale ±[2 mV + 0.007 (Offset) + 0.02 (Vertical Value – Offset)] 80E01 10 mV to 1.0 V full scale ±[2 mV + 0.007 (Offset) + 0.02 (Vertical Value – Offset)] * 11 Values shown are warranted unless printed in an italic typeface which represents a typical value. * 26 Calculated from formula rise time = 0.35/(typical bandwidth). Typical Step Response Aberrations RMS Noise* 11 ±1% or less over the zone 10 ns to 20 ps before step transition; +6%, –10% or less for the first 400 ps following step transition; +0%, –4% or less over the zone 400 ps to 3 ns following step transition; +1%, –2% or less over the zone 3 ns to 100 ns following step transition; ±1% after 100 ns following step transition ±1% or less over the zone 10 ns to 20 ps before step transition; +6%, –10% or less for the first 400 ps following step transition; +0%, –4% or less over the zone 400 ps to 3 ns following step transition; +1%, –2% or less over the zone 3 ns to 100 ns following step transition; ±1% after 100 ns following step transition ±1% or less over the zone 10 ns to 20 ps before step transition; +6%, –10% or less for the first 400 ps following step transition; +0%, –4% or less over the zone 400 ps to 3 ns following step transition; +1%, –2% or less over the zone 3 ns to 100 ns following step transition; ±1% after 100 ns following step transition ±1% or less over the zone 10 ns to 20 ps before step transition; +6%, –10% or less for the first 400 ps following step transition; +0%, –4% or less over the zone 400 ps to 3 ns following step transition; +1%, –2% or less over the zone 3 ns to 100 ns following step transition; ±1% after 100 ns following step transition ±5% or less for first 300 ps following step transition ±3% or less over the zone 10 ns to 20 ps before step transition; +10%, –5% or less for the first 300 ps following step transition; ±3% or less over the zone 300 ps to 5 ns following step transition; ±1% or less over the zone 5 ns to 100 ns following step transition; 0.5% after 100 ns following step transition ±3% or less over the zone 10 ns to 20 ps before step transition; +10%, –5% or less for the first 300 ps following step transition; ±3% or less over the zone 300 ps to 5 ns following step transition; ±1% or less over the zone 5 ns to 100 ns following step transition; ±0.5% after 100 ns following step transition ±3% or less over the zone 10 ns to 20 ps before step transition; +12%, –5% or less for the first 300 ps following step transition; +5.5%, –3% or less over the zone 300 ps to 3 ns following step transition; ±1% or less over the zone 3 ns to 100 ns following step transition; ±0.5% after 100 ns following step transition 50 GHz: 600 μV, ≤700 μV 40 GHz: 370 μV, ≤480 μV 30 GHz: 300 μV, ≤410 μV 60 GHz: 450 μV, ≤600 μV 40 GHz: 330 μV, ≤480 μV 30 GHz: 300 μV, ≤410 μV 30 GHz: 300 μV, ≤410 μV 20 GHz: 280 μV, ≤380 μV 30 GHz: 300 μV, ≤410 μV 20 GHz: 280 μV, ≤380 μV 1.8 mV, ≤2.4 mV (maximum) 600 µV, ≤1.2 mV (maximum) 600 µV, ≤1.2 mV (maximum) 1.8 mV, ≤2.3 mV (maximum) 22 www.tektronix.com
Digital Serial Analyzer Sampling Oscilloscope — DSA8200 S-parameter Performance Characteristics (80E10) Measurement Conditions All measurements were performed after proper warm up as specified in the DSA8200 manual Standard S-parameter dynamic range measurement practices were used to determine the dynamic range of the module Uncertainty results were derived from a wide range of devices, with 250 averages Better dynamic range can be achieved by selecting lower bandwidth settings on the 80E10 module due to lower RMS noise floor Results apply to single-ended or differential measurements Dynamic Range Uncertainty www.tektronix.com 23
Page 1 and 2: Digital Serial Analyzer Sampling Os
Page 21: Digital Serial Analyzer Sampling Os

Download File &#40;1.01 MB&#41; - Tektronix

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?

Download File (1.01 MB) - Tektronix