Glassfront BevMax 3 Vender - The Vending Center

More documents

Recommendations

Info

CUP AT WRONG LOCATION LEFT /RIGHT or X AXIS Go to Factory Diagnostics. Check encoder counts. Send to home, does home switch light come on? YES NO See XY not working page 31. Send cup to home position. Does it go home? YES NO Send cup to “E2-E8” positions. Does it stop in correct position? YES NO See X Axis TS page 33. Repeat test at several locations. Does it stop in correct position? NO YES Is the horizontal alignment correct? YES NO Check Harness, Keypad, Motor, Board. Do a Keypad test. Works? YES NO Check Harness, Keypad, Motor, Board. Adjust Shelf Offset as required. See pg 17. Close door, do a test vend. Change Keypad. 38
DELIVERY PORT DOOR WORKS IN FACTORY DIAGNOSTICS BUT NOT IN SALES MODE Close door and do a test vend. Does it work? YES NO Open service door. Pull top door switch out and do a test vend. Does it work? YES NO Check, repair, and replace door switch components: mounting bracket, strike plate, switch, and harness. Go to Factory Diagnostics, manually close the delivery port door. Is the green LED on control board on and Port door switch close code is 1? YES NO Use Factory Diagnostics to open the delivery port door. Is the yellow LED on control board on and Port Door open switch code is 1? YES NO Check, repair, and replace door close switch PORT DOOR TEST SWITCH CODES ABCD Position A = Open switch (yellow LED on control board) Position B = Close switch (Green LED on control board) Position C = Vend sensor (on/off) Position D = Vend detect (Red LED on if it sees something in port – only if “C” is 1 [vend sensor on]) Check, repair, and replace door open switch, harness, motor. Is port open all the way? YES NO Check for physical obstructions. 39
Page 1 and 2: Glassfront BevMax 3 Vender Model DN
Page 3 and 4: Bill Acceptors.....................
Page 5 and 6: WARNING: TO AVOID THE POSSIBILITY O
Page 7 and 8: and weight of the Vender, never att
Page 9 and 10: to the evaporator coils and reads t
Page 11 and 12: or CLR to return to SET PRICES. Pre
Page 13 and 14: SERVICE MODE MENU ITEMS Note: Menu
Page 15 and 16: “” to set more prices or CLR to
Page 17 and 18: d. Key “D” to turn sensor off.
Page 19 and 20: “Credit Timer Mode”. Press the
Page 21 and 22: STS ENABLE OFF CUSTOM STS CLEARED N
Page 23 and 24: is installed in the controller, pow
Page 25 and 26: SET STORAGE TIME - Press key “9
Page 27 and 28: 2 8 4 14 7 11 5 3 BevMax 2/3 12 6 1
Page 29 and 30: a. Check error list. Does error lis
Page 31 and 32: XY not working Is vender plugged in
Page 33 and 34: X Axis Home = Yellow light ON OFF C
Page 35 and 36: XY Slams to Top/ Right 0r Left NO Y
Page 37: CUP AT WRONG LOCATION HIGH/LOW or Y
Page 41 and 42: These charts are intended as a guid
Page 43 and 44: INCORRECT CHANGE DISPENSED Incorrec
Page 45 and 46: ICE / FROST ON EVAPORATOR Ice / fro
Page 47 and 48: MACHINE NOT COOLING Machine not coo
Page 49 and 50: BevMax 3 Export Block Diagram X Mot
Page 51 and 52: BevMax 3 Cabinet Diagram (Domestic
Page 53 and 54: BevMax 3 Domestic Power & Lighting
Page 55 and 56: BevMax 3 Compressor Parts Diagram 5
Page 57 and 58: PARTS LIST PARTS LIST AND DIAGRAMS.
Page 59 and 60: MACHINE FRONT VIEW ITEM PART DESCRI
Page 61 and 62: CABINET DETAIL PRODUCT AREA ITEM PA
Page 63 and 64: CABINET DETAIL SERVICE DOOR AREA IT
Page 65 and 66: XY MOTOR PICKER UNIT ITEM PART DESC
Page 67 and 68: PICKER CUP ASSEMBLY ITEM PART DESCR
Page 69 and 70: SERVICE DOOR (OUTSIDE) ITEM PART DE
Page 71 and 72: SERVICE DOOR (INSIDE) ITEM PART DES
Page 73 and 74: GATE TRAY DETAIL ITEM PART DESCRIPT
Page 75 and 76: AC DISTRIBUTION BOX ITEM PART DESCR
Page 77 and 78: REFRIGERATION UNIT (BevMax 3 FIN &
Page 79 and 80: ELECTRONICS ITEM PART DESCRIPTION D
Page 81 and 82: HARNESSES ITEM PART DESCRIPTION FRO
Page 83 and 84: SCREWS & NUTS 83
Page 85 and 86: WASHERS, BOLTS, & MISC. HARDWARE 85

Glassfront BevMax 3 Vender - The Vending Center

Create successful ePaper yourself

Delete template?

Save as template?