Welcome to the Next Generation of Sealing ... - CE Franklin Ltd.
Welcome to the Next Generation of Sealing ... - CE Franklin Ltd.
Welcome to the Next Generation of Sealing ... - CE Franklin Ltd.
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Spiral Wound Gaskets<br />
Manufacturing Capabilities and Tolerances<br />
Recommended Design Parameters<br />
Gasket Maximum Maximum Recommended<br />
Thickness Inside Recommended Compressed<br />
Dimension Crossectional Width Thickness **<br />
0.0625” Up <strong>to</strong> 6” 3/8” 0.050” / 0.055”<br />
0.0625” 6” <strong>to</strong> 15” 1/4” 0.050” / 0.055”<br />
0.100” 10” 1/2” 0.075” / 0.080”<br />
0.125” Up <strong>to</strong> 20” 1” 0.090” / 0.100”<br />
0.125” * 20” <strong>to</strong> 40” 3/4” 0.090” / 0.100”<br />
0.175” Up <strong>to</strong> 40” 1” 0.125” / 0.135”<br />
0.175” * 40” <strong>to</strong> 60” 1” 0.125” / 0.135”<br />
0.175” * 60” <strong>to</strong> 70” 7/8” 0.125” / 0.135”<br />
0.175” * 70” <strong>to</strong> 75” 3/4” 0.125” / 0.135”<br />
0.250” 90” 1” 0.180” / 0.200”<br />
0.285” 185” 1” 0.200” / 0.220”<br />
Preferred size range in relation <strong>to</strong> thickness shown in bold type.<br />
* PTFE filled FLEXITALLIC gaskets in this size range are unstable and are subject <strong>to</strong> “springing apart” in shipping and<br />
handling. Specify next gasket thickness up.<br />
** The recommended compressed thickness is what experience has indicated <strong>to</strong> be <strong>the</strong> optimum range in order <strong>to</strong><br />
achieve maximum resiliency <strong>of</strong> <strong>the</strong> gasket. Additional compression <strong>of</strong> 0.010” may be <strong>to</strong>lerated on all gasket thicknesses<br />
with <strong>the</strong> exception <strong>of</strong> <strong>the</strong> 0.0625” and <strong>the</strong> 0.100” thick gaskets. This is on <strong>the</strong> assumption that <strong>the</strong> flange surface<br />
finishes are relatively smooth. Refer <strong>to</strong> “Surface Finish Requirements” on page 46. When attempting <strong>to</strong> contain<br />
hard <strong>to</strong> hold fluids, or pressures above 1000 psi, it is suggested that compression be maintained at <strong>the</strong> lower range <strong>of</strong><br />
<strong>the</strong> recommended compressed thickness.<br />
Tolerances<br />
Gasket Diameter Inside Diameter Outside Diameter<br />
Up <strong>to</strong> 10” ± 1/64” ± 1/32”<br />
10” <strong>to</strong> 24” ± 1/32” ± 1/16”<br />
24” <strong>to</strong> 60” ± 3/64” ± 1/16”<br />
60” & Above ± 1/16” ± 1/16”<br />
Tolerance on gasket thickness is ± 0.005”, (measured across metal winding) on all<br />
thicknesses.<br />
28<br />
<strong>Welcome</strong> <strong>to</strong> <strong>the</strong> <strong>Next</strong> <strong>Generation</strong> <strong>of</strong> <strong>Sealing</strong> Technology<br />
®