USER'S MANUAL - Pyramid Car Audio

More documents

Recommendations

Info

features and controls 2 ch amp PB1836GX pb-1836GX power LED protection LED Remote Bass Boost REMOTE BASS BOOST PROTECT 2 CHANNEL MOSFET AMPLIFIER POWER HPF LPF BASS BOOST FREQ. LEVEL L R HI IN R L + - - + 80 2.5k Hz 35 400 Hz 0 +18db HPF LPF FULL MIN MAX LOW IN high pass frequency control low pass frequency control bass boost level crossover mode selector high level inputs low level inputs input level control 14 speaker connections + L R FUSE - + - GROUND REM +12V BATT power terminals + BRIDGED - power fuse
crossover mode selectors input level controls low pass frequency controls high pass frequency controls Remote Bass Boost bass boost level controls low level inputs high level inputs power LED protection LED power fuse power terminals speaker connections when used with normal, full range systems, set these switches to “FULL.” If you wish to use the internal crossovers to power a driver of specific frequency range, use the “LOWPASS” or “HIGHPASS” settings. use these controls to match the outputs of your head unit to the amplifier. Starting with your head unit set at about the 2 o’clock position, increase the amp level controls until distortion begins to occur, and reduce slightly from this point. when one or both of the crossover selector switches is in “low pass” mode, one can set the upper frequency limit for audio program sent to the speakers. when the one or both of crossover selector switch is in “high pass” mode, one can set the lower frequency limit for audio program sent to the speakers. Plug in the Remote Bass Boost Control wire in here. this control permits adjustment of the bass level up to an increase of approximately 18 dB in either or both pairs of channels. this amp features gold-plated RCA input jacks for high impedance input. Use these with car stereo output which uses RCA-type connector cables. if your car stereo lacks RCA-type output jacks, you may connect speaker output leads to these input connectors. this indicator is illuminated when power is applied. this indicator is illuminated when built-in protection circuitry is activated. the fuse protects the amplifier and your car’s electrical system from short circuit conditions. use these connectors to deliver power, ground and remote turn-on control to the amplifier. these terminals are 14K gold plated to guarantee high conductivity and minimum signal loss. features and specifications output power @ 14.4v DC, 1KHz RMS Power @ 4 Ohms RMS Power @ 2 Ohms Maximum Power Output frequency response input impedance low level inputs high level inputs input sensitivity low level inputs high level inputs power supply voltage matching speaker impedance stereo mode bridged mode maximum current draw dimensions (W x H x L) mm inches 2 ch amp PB-1236GX • PB-1836GX PB -1236GX 125 Watts x 2 200 Watts x 2 800 Watts x 2 15 Hz-30 KHz 10K Ohms 100 Ohms 250mV 2.5V 150 Watts x 2 225 Watts x 2 1200 Watts x 2 14.4V DC Neg. Ground (10.5-16V) 2-4 Ohms 4-8 Ohms 30 A 40 A 278 x 81 x 381 10.9 x 3.2 x 15 PB -1836GX 278 x 81 x 432 10.9 x 3.2 x 17 15
Page 1 and 2: PB-136GX PB-336GX PB-536GX PB-736GX
Page 3 and 4: table of contents electrical connec
Page 5 and 6: general features PB-536GX High Perf
Page 7 and 8: general features PB-1236GX High Per
Page 9 and 10: features and specifications 2 ch am
Page 11 and 12: features and specifications 4 ch am
Page 13 and 14: crossover mode selector input level
Page 15: crossover mode selectors input leve
Page 19 and 20: dual crossover mode selectors dual
Page 21 and 22: dual crossover mode selectors dual
Page 23 and 24: electrical connections 4 ch amp PB-
Page 25 and 26: using low level inputs stereo input
Page 27 and 28: CH4 CH3 + - - + CH4 CH3 + - - + 4 C
Page 29 and 30: 4 CH Stereo input connections using
Page 31 and 32: 4 CH mono input connections using l
Page 33 and 34: Stereo Output Mode speaker connecti
Page 35: speaker connections 4 ch amp PB-636

USER'S MANUAL - Pyramid Car Audio

Create successful ePaper yourself

Delete template?

Save as template?