USER'S MANUAL - Pyramid Car Audio

More documents

Recommendations

Info

features and controls 4 ch amp PB-636GX pb-636GX ch 3/4 input level control ch 3/4 high level inputs + - - + CH4 CH3 HI IN CH 4 CH 3 LEVEL MIN MAX FREQ. HPF LPF FULL BASS BOOST LPF 0 +18db 35 400 Hz HPF PROTECT POWER HPF LPF 80 2.5k 80 2.5k 35 400 Hz Hz Hz BASS BOOST 0 +18db FREQ. HPF LPF FULL MIN LEVEL MAX CH 2 CH 1 + - - + CH2 CH1 HI IN ch 1/2 input level control ch 1/2 high level inputs CHANNEL 3/4 CHANNEL 1/2 LOW IN 4 CHANNEL MOSFET AMPLIFIER LOW IN ch 3/4 low level inputs ch 3/4 crossover mode selector switch ch 3/4 bass boost level control ch 3/4 low pass frequency control ch 3/4 high pass frequency control protection LED power LED ch 1/2 low level inputs ch 1/2 crossover mode selector switch ch 1/2 bass boost level control ch 1/2 low pass frequency control ch 1/2 high pass frequency control 16 speaker connections CH1 + - CH2 + - CH3 + - CH4 + - FUSE GROUND REM +12V BATT power terminals + BRIDGED - + BRIDGED - power fuse
dual crossover mode selectors dual input level controls dual low pass frequency controls dual high pass frequency controls dual bass boost level controls low level inputs high level inputs power LED this indicator is illuminated when power is applied. protection LED this indicator is illuminated when built-in protection circuitry is activated. power fuse power terminals when used with normal, full range systems, set these switches to “FULL.” If you wish to use the internal crossovers to power a driver of specific frequency range, use the “LOWPASS” or “HIGHPASS” settings. use these controls to match the outputs of your head unit to the amplifier. Starting with your head unit set at about the 2 o’clock position, increase the amp level controls until distortion begins to occur, and reduce slightly from this point. when one or both of the crossover selector switches is in “low pass” mode, one can set the upper frequency limit for audio program sent to the speakers. when the one or both of crossover selector switch is in “high pass” mode, one can set the lower frequency limit for audio program sent to the speakers. this control permits adjustment of the bass level up to an increase of approximately 18 dB in either or both pairs of channels. this amp features gold-plated RCA input jacks for high impedance input. Use these with car stereo output which uses RCA-type connector cables. if your car stereo lacks RCA-type output jacks, you may connect speaker output leads to these input connectors. the fuse protects the amplifier and your car’s electrical system from short circuit conditions. use these connectors to deliver power, ground and remote turn-on control to the amplifier. features and specifications 4 ch amp PB-636GX output power @ 14.4v DC, 1KHz RMS Power @ 4 Ohms RMS Power @ 2 Ohms Maximum Power Output frequency response input impedance low level inputs high level inputs input sensitivity low level inputs high level inputs power supply voltage matching speaker impedance stereo mode bridged mode maximum current draw dimensions (W x H x L) mm inches 35 Watts x 4 55 Watts x 4 250 Watts x 4 15 Hz-30 KHz 10K Ohms 100 Ohms 250mV 2.5V 14.4V DC Neg. Ground (10.5-16V) 2-4 Ohms 4-8 Ohms 20A 278 x 81 x 305 10.9 x3.2 x 12 17 speaker connections these terminals are 14K gold plated to guarantee high conductivity and minimum signal loss.
Page 1 and 2: PB-136GX PB-336GX PB-536GX PB-736GX
Page 3 and 4: table of contents electrical connec
Page 5 and 6: general features PB-536GX High Perf
Page 7 and 8: general features PB-1236GX High Per
Page 9 and 10: features and specifications 2 ch am
Page 11 and 12: features and specifications 4 ch am
Page 13 and 14: crossover mode selector input level
Page 15 and 16: crossover mode selectors input leve
Page 17: crossover mode selectors input leve
Page 21 and 22: dual crossover mode selectors dual
Page 23 and 24: electrical connections 4 ch amp PB-
Page 25 and 26: using low level inputs stereo input
Page 27 and 28: CH4 CH3 + - - + CH4 CH3 + - - + 4 C
Page 29 and 30: 4 CH Stereo input connections using
Page 31 and 32: 4 CH mono input connections using l
Page 33 and 34: Stereo Output Mode speaker connecti
Page 35: speaker connections 4 ch amp PB-636

USER'S MANUAL - Pyramid Car Audio

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?