Planar UltraRes Series CAD Drawings
Planar UltraRes Series CAD Drawings
Planar UltraRes Series CAD Drawings
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
050-0218-00 REV B<br />
8<br />
7<br />
6<br />
5<br />
4<br />
3<br />
2<br />
1<br />
49.97<br />
1269.3<br />
D<br />
12.31<br />
312.7<br />
D<br />
5.26<br />
133.6<br />
6.37<br />
161.8<br />
43.73<br />
1110.7<br />
2X PANEL HANGER<br />
FLUSH OR<br />
1.18<br />
30.1<br />
1.18<br />
30.1<br />
MIN<br />
1.18<br />
30.1<br />
MIN<br />
1.00<br />
25.4 TYP<br />
C<br />
C<br />
DISPLAY OUTLINE<br />
REAR TRIM<br />
SHEET. SINGLE<br />
PEDESTAL ONLY<br />
UNIT<br />
75.54<br />
1918.7<br />
87.80<br />
2230.2<br />
UNIT<br />
UNIT<br />
B<br />
SERVICE<br />
KICKSTAND<br />
B<br />
2X PANEL LOCK<br />
CLIPS<br />
13°<br />
2.11<br />
53.6<br />
9.26<br />
235.3<br />
REMOVABLE HOLE PLUG<br />
FOR CABLE ROUTE<br />
BOTH SIDES<br />
26.3<br />
668<br />
14.64<br />
371.9<br />
14.64<br />
371.9<br />
14.64<br />
371.9<br />
SINGLE SIDED<br />
PEDESTAL<br />
2X REMOVABLE TRIM<br />
FOR TIE DOWN AND<br />
CABLE ACCESS<br />
DOUBLE SIDED<br />
PEDESTAL<br />
3. ATTACH REAR TRIM WITH TAPE PROVIDED.<br />
2. SERVICE MODE IS THE SAME AS THE PORTRAIT WALL INSTALL.<br />
1. PEDESTAL SHALL BE ATTACHED TO A FIXED SURFACE PRIOR TO PANEL<br />
INSTALLATION TO PREVENT TIPPING.<br />
A<br />
NOTES: UNLESS OTHERWISE SPECIFIED.<br />
A<br />
8<br />
7<br />
8.00<br />
203.2<br />
6<br />
CABLE ACCESS<br />
5<br />
.61<br />
8X 15.5<br />
PEDESTAL MOUNT<br />
HOLES<br />
4<br />
THIS DRAWING CONTAINS INFORMATION PROPRIETARY TO PLANAR SYSTEMS, INC., ANY REPRODUCTION IN PART OR WHOLE WITHOUT THE WRITTEN PERMISSION OF PLANAR SYSTEMS<br />
IS PROHIBITED. THIS DRAWING IS SUPPLIED FOR INFORMATION, IDENTIFICATION, ENGINEERING, EVALUATION, AND/OR INSPECTION PURPOSES ONLY AND MAY NOT BE USED AS BASIS<br />
FOR THE MANUFACTURING OF PRODUCTS OR THE FURNISHING OF SERVICES TO PLANAR SYSTEMS OR TO ANY THIRD PARTY UNLESS AUTHORIZED IN WRITING BY PLANAR SYSTEMS.<br />
3<br />
ENGR BY<br />
UNLESS OTHERWISE SPECIFIED<br />
DIMENSIONS ARE IN MILLIMETERS [INCHES].<br />
DRAWN BY<br />
TOLERANCES:<br />
X= ±1<br />
.X= ±.5<br />
XX= ±.25<br />
= ±1°<br />
DIMENSIONING AND TOLERANCING PER<br />
ASME Y14.5M-1994<br />
THIRD ANGLE PROJECTION<br />
CHECKED BY<br />
USED ON<br />
MATERIAL<br />
FINISH<br />
2<br />
EJS<br />
EJS<br />
18DEC12<br />
18DEC12<br />
TITLE<br />
SIZE<br />
D<br />
PART NO.<br />
SCALE<br />
PLANAR SYSTEMS, INC.<br />
1195 NW COMPTON DRIVE<br />
BEAVERTON, OR 97006 USA<br />
84" ULTRARES PEDESTAL<br />
MOUNTING<br />
-<br />
DRAWING NO.<br />
1:8 DO NOT SCALE<br />
-<br />
SHEET<br />
1<br />
4 OF 6<br />
REV<br />
A
Change language