PDF | 11.6 MB - Protektor

DIRECTIONS
RASTATT
A5
BISCHWEIER
Gewerbegebiet
Birking
Bruchgrabenstraße
BASEL
KARLSRUHE
FREUDENSTADT
HOW TO FIND US:
AUSFAHRT
GAGGENAU-
BAD ROTENFELS
Murgtalstraße
Luisenstraße
Bruchgrabenstraße
Coming from A5:
B 462
Take the autobahn exit Rastatt in the
direction of Gaggenau/Freudenstadt.
After approximately 8 km, turn left towards
Gaggenau-Bad Rotenfels at the traffic light.
Turn right after the bridge and take Murgtalstraße through
Bad Rotenfels.
Turn left at the traffic light onto Bruchgrabenstraße through Gewerbegebiet Birkig
into roundabout traffic, then straight ahead.
Turn right onto Theodor-Bergmann-Straße after 500 meters.
Theodor-Bergmann-Straße
Viktoriastraße
Goethestraße
Schillerstraße
Berliner Straße
Coming from Freudenstadt:
Take the exit Gaggenau-Mitte/DaimlerChrysler, then turn left above the bridge.
Turn left after the bridge, above the railway crossing onto Schillerstraße.
Turn left after 200 meters onto Goethestraße.
Continuing driving straight until roundabout traffic, then turn right onto Bruchgrabenstraße.
Turn right onto Theodor-Bergmann-Straße after 500 meters.
MURG
FREUDENSTADT

Summary
Please note:
All recommended load values for suspension pieces refer to vertical tension loads only. Information on static or dynamic values is
available on request. The values mentioned in the catalogue are only valid for use with genuine Protektorwerk components. Where
other components are used, we decline any responsability.
Explanation of abreviations:
adm. f. … kN = values backed by test certification.
max. f. … kN = values recommended through experience, given without obligation.
Table of Contents, with ref. nos. 2
Ceilings
Page
Code list ceilings 4–14
Expanded metal plates (Trigoform 300 AS and Unoform systems) 15
General ceiling product information 16–17
Ceiling systems K 400 S – K 1100 18–47
Ceiling details 28–29
Wide span profiles 30–39
Partitions and wall linings
Code list wall profiles and accessories 50–54
Self tapping screws and dowels 55
Accessory profiles for drylining 56–61
Partition and ceiling profiles to international standards 62–63
SILENCIO, the Protektor sound insulation programme 64
MAXI-SCW-profiles for increased sound insulation values 65 + 68–69
Overview of partitions and wall linings,
technical data and material requirements 66–67
Metal stud wall structure and facing plywood 68–87
Glazing with standard profiles 88–89
Particular construction details 90–94
Accessories
»Profil«-supports and horizontal bars for sanitary ware 95–105
Drylining tools 106
Example for dry lining of the attic 107
Product information 108
© 2007 Protektorwerk
No part of this publication may be reproduced or copied without the prior permission of Protektorwerk.
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 1

Table of contents
with Ref. Nos.
Ref.
Page
10 . .
1030 57
1078 57
11 . .
1118 61
1119 61
1120 58
1121 58
1122 58
1123 58
1124 61
1131 59
1132 59
1133 59
1134 59
1135 59
1136 59
1138 59
13 . .
1311 59
1313 59
1314 59
1315 59
1319 59
1328 59
1371 59
17 . .
1750 59
1751 59
20 . .
2041 61
2065 61
2066 61
21 . .
2158 61
2160 61
2162 61
2178 61
2180 61
2182 61
22 . .
2241 59
2263 59
30 . .
3001 57
32 . .
3226 61
35 . .
3502 58
3519 4
3520 4
36 . .
3651 53
3655 53
37 . .
3703 53
3738 58
3741 58
3744 58
3747 58
3750 61
3751 57
3762 53
3765 53
3766 60
3767 60
3768 60
3769 4
3770 60
3772 60
3774 60
3776 60
3778 60
3780 60
Ref.
Page
3784 60
3789 60
44 . .
4410 36
4415 36
4419 36
4420 36
4426 36
4427 36
45 . .
4519 36
4525 36
4529 36
4530 36
4540 36
4541 36
4542 36
4543 36
4544 36
4550 36
4551 36
4552 36
4553 36
47 . .
4710 36
4715 36
48..
4810 36
4815 36
49..
4914 36
4915 36
4918 36
4919 37
4920 36
4923 36
4925 36
4929 36
4930 36
50 . .
5004 13
5007 9/38
5072 11
51 . .
5100 54
5104 11
5106 63
5107 62
5108 62
5109 62
5110 13
5112 52
5114 9/38
5115 63
5116 8/38
5117 8/12
5118 8
5119 8
5120 8/52
5121 8
5125 8
5126 16/34
5127 16/34
5128 8
5129 34/51
5130 34/51
5131 34/51
5132 34/51
5133 52
5134 52
5135 51
5136 52
5137 16/34
5138 16/34
Ref. Page Ref. Page Ref. Page Ref. Page
5139 53
5141 32/50
5143 14/52
5156 53
5158 9
5160 4
5161 4
5162 4
5164 4
5165 4
5167 9
5168 8/52
5170 51
5173 52
5174 52
5177 4
5178 4/32
5179 9
5180 4/32
5182 54
5183 54
5184 54
5185 63
5187 63
5189 63
5192 52
5193 52
52 . .
5206 50
5207 50
5208 50
5211 32/50
5214 50
5215 32/50
5216 32/50
5218 32/50
5219 32/50
5221 32/50
5224 50
5230 32/50
5232 50
5233 32/50
5234 32/50
5236 50
5237 50
5238 50
5242 8
5243 8
5244 8/52
5247 50
5248 32/50
5261 50
5262 50
5263 50
5269 50
5275 50
5276 50
5277 50
5278 50
5279 50
53 . .
5312 11
5328 4
5329 4
5332 4
5334 4
5335 12
5336 12
5337 12
5340 12
5341 12
5342 12
5343 12
5344 12
5345 12
5346 12
5347 12
5348 12
54 . .
5440 51
5441 51
5442 51
5443 51
5444 51
5445 51
5448 4
5460 63
5477 63
55 . .
5501 54
5502 34
5511 11
5512 11
5513 11
5514 11
5516 11
5517 11
5518 11
5519 11
5521 11
5522 11
5523 11
5524 11
5526 12
5527 12
5528 12
5529 12
5531 12
5532 12
5533 12
5534 12
5536 12
5537 12
5538 12
5539 12
56 . .
5601 51
5615 51
5616 51
5660 63
5677 63
56831 99
56832 103
56833 103
56835 100
56837 102
56838 104
56840 101
56851 98
56852 97
58 . .
5801 63
5802 63
5803 63
5804 63
5805 63
5806 63
5807 63
5808 63
5817 63
5836 63
5848 63
5849 63
5869 63
5870 63
5890 63
5899 63
59 . .
5900 63
5901 63
5902 63
5903 63
5904 63
5905 63
5906 63
5936 63
5937 63
5944 63
5970 63
5990 63
5999 63
60 . .
6001 7
6005 7
6008 5
6009 5
6010 5
6011 14
6012 9
6013 9
6014 9
6015 14
6016 13
6017 14
6018 9
6019 6
6020 6
6021 6
6022 6
6023 6
6024 6
6025 6
6026 6
6027 6
6028 6
6029 6
6031 6
6032 6
6033 14
6034 10
6038 10
6039 7
6041 5
6042 5
6043 5
6044 5
6045 5
6046 5
6048 5
6050 5
6051 5
6052 5
6053 5
6054 5
6055 5
6056 5
6059 10
6060 14
6061 10
6065 13
6070 7
6071 7
6072 7
6076 14
6078 10
6080 13
6085 13
6090 10
6093 9/38
6094 10
6095 10
6099 13
61 . .
6100 11
6101 10
6104 10
6105 12
6110 9
6112 13
6113 4
6114 4
6116 11
6117 7
6118 7
6120 62
6121 62
6122 62
6123 62
6124 62
6125 62
6126 11
6127 11
6129 7
6131 14
6132 14
6133 14
6134 14
6135 14
6137 14
6139 14
6141 10
6144 14
6146 14
6148 14
6149 52
6150 52
6151 52
6153 13
6154 52
6155 52
6156 52
6157 8
6158 52
6159 8
6160 8
6162 13
6164 14
6165 14
6166 8
6167 8
6168 62
6169 8
6175 50
6176 50
6178 55
6179 16/34
6180 50
6181 50
6182 32/51
6183 32/51
6184 16/34
6185 32/51
6186 38
6187 50
6188 50
6189 50
6194 50
6195 50
6196 50
6197 50
6199 6
62 . .
6200 6
6201 6
6203 16/51
Ref. Page Ref. Page
6204 7
6205 55
6206 55
6208 55
6209 55
6211 55
6212 55
6213 55
6215 55
6216 55
6217 55
6218 55
6219 55
6222 55
6223 55
6224 55
6225 55
6227 55
6233 55
6234 55
6236 55
6237 55
6238 55
6239 55
6240 55
6241 55
6242 55
6248 50
6249 55
6250 55
64 . .
6412 98
6424 98
6426 98
6427 98
6429 98
6430 98
6431 98
6432 98
6435 98
6436 98
6437 98
6438 98
6485 98
6486 98
6487 98
65 . .
6510 98
6511 98
6512 98
6513 98
6514 98
6515 98
6516 98
6517 98
6545 53
6549 53
6551 53
6552 53
6553 53
6554 53
6555 53
6578 53
6580 38
6581 38
6582 38
6583 38
6584 13
6586 38
6587 38
6588 38
6589 38
6590 38
66 . .
6670 54/105
67 . .
6751 51
6752 51
6753 51
90 . .
9002 57
9077 57
9078 57
9079 57
91 . .
9172 57
9178 57
9179 57
92 . .
9278 57
9298 57
9299 57
2
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

GENERATION »CD« HANGER
FOR C-CEILING PROFILES

Profiles and accessories
for suspended ceilings Approved to DIN 18168/2
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Angle profile galvanised, coated
Angle profile galvanised
PVC-angle profile
5334
5328
5332
300
300
300
0.5
0.5
0.5
19.6
17.0
25.5
40
40
40
„A x B“
24 x 24 mm, white
19 x 19 mm, white
30 x 30 mm, white
5160
5161
5162
5164
5177
5165
400
400
400
250
300
300
0.56
0.56
0.56
0.60
1.0
1.0
19.3
23.7
35.2
43.5
62.0
47.0
20
20
20
20
10
8
„A x B“
23 x 23 mm
28 x 28 mm
41 x 41 mm
50 x 50 mm
40 x 40 mm
40 x 20 mm
3519
3520
250
500
250
500
2.5
2.0
22.8
13.6
20
20
„A x B“
35 x 35 mm
25 x 25 mm
Colour Nos:
white 10
brick red 33
black 90
brown 47
Other colours
on request
Further dimensions
on request
Corner connector for angle profile
ref. 5334, galvanised, coated, white
Angle profile 135° galvanised
Suspension angle profile
galvanised, perforation Ø 6.5
6114
6113
–
–
0.40
0.40
1.0
1.0
100
100
for inner corner
for outer corner
5448
300
0.60
65.0
10
5178
400
2.00
76
8
PVC-angle profile white,
flexible concave/convex
3769
250
1.5
13.9
10
Angle profile galvanised,
for shadow joints, white coated
Angle profile galvanised
5329
300
0.5
25.0
40
5180
300
1.5
104
10
4
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Approved to DIN 18168/2
Profiles and accessories
for suspended ceilings
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Suspension wire Ø 4
galvanised with eye Ø 6
Tension spring galvanised,
with wire hook
6041
6042
6043
6044
6045
6046
6048
6050
12.5
25
37.5
50
75
100
125
150
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
1.4
2.7
3.9
5.1
7.4
9.7
11.8
14.8
100
100
100
100
100
100
100
100
eye
Ø 6
also
available
in fixed
lengths
6009
6008
10
20
–
–
1.8
2.5
100
100
with wire hook 100 mm
with wire hook 200 mm
adm. f. 0.25 kN
Suspension wire Ø 4
galvanised, with hook
6051
6052
6053
6054
6055
6056
12.5
25
37.5
50
75
100
4.0
4.0
4.0
4.0
4.0
4.0
1.4
2.7
3.9
5.1
7.4
9.7
100
100
100
100
100
100
Double tension spring galvanised
for inserting wire on the side
6010
–
0.75
2.3
250
adm. f. 0.40 kN
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 5

Profiles and accessories
for suspended ceilings Approved to DIN 18168/2
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
System extension Nonius hanger
Adjusting strip galvanised,
for Nonius hanger
Adjusting bolt galvanised, for connection
of adjusting strip and Nonius hanger
6020
6021
6022
6023
6024
6025
6026
6027
6028
6029
6019
13,5
20
30
40
50
60
70
80
90
100
170
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
2.5
3.5
5.6
7.5
9.0
10.5
12.6
15.0
16.5
17.5
31.0
100
100
100
100
100
100
100
100
100
100
50
Ø 7
also
available
in fixed
lengths
6200
4.9
–
0.3
200
each connection:
2 pieces
adjustment nails
must be turned after
installation
Adjusting Strip
Nonius Connector
ref. 6032
Nonius connector galvanized
for extensions
Adjusting bracket for the connection
of adjusting strip and extension strip
6032 9 1.0 2.0 100
as connection to
adjusting strip
6201
–
–
0.5
100
per connection
1 piece
safety clamps
must be turned after
installation
Extension Strip
ref. 6031
Nonius bars for adjusting strip
extension, galvanized
6031 300 1.0 17.4 20
Nonius hanger
e.g. ref. 6018
Adjusting clamp
for Nonius suspension system
6199 – – 0.6 100
each connection:
2 pieces
Per connection utilise 2 adjusting clamps
ref. 6199.
6
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Approved to DIN 18168/2
Profiles and accessories
for suspended ceilings
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Slotted metal strip galvanised,
20 x 1.5 mm
Fixing bracket galvanised,
for NP-profiles
Suspension bracket for CD profiles
Order no. 5117 – 5120
6001 5000 1.5 17 coil
à
50
m
6070
6071
6072
–
–
–
Ø4.3
Ø4.3
Ø4.3
3.5
4.1
5.3
100
100
100
span range: d:
50–85 mm < 9 mm
85–130 mm < 13.5 mm
130–210 mm < 18.5 mm
6117
6118
170
270
-
-
3.8
6.0
100
100
span range
170
270
d
max. f. 0.25 kN
clamping area
NP carrier
Anti-Vibration hanger galvanised,
with elastic absorption element
Perforated metal strip galvanised,
20 x 1.5 mm
Fixing bracket
ref. 6070, ref. 6071, ref. 6072
6039 7 – 3.4 100
approved for fire rated ceilings
6005 5000 1.5 19 coil
à
50
m
Suspension wire with eye ref. 6041
to ref. 6050 or
Adjusting strip nr. 6020 to ref. 6029
CD-hanger with special spring ref. 6038
or CD-nonius hanger ref. 6018
C-ceiling profile ref. 5120
Flat head screw galvanised,
with special square collar
C-ceiling profile
ref. 5120
Angle anchor ref. 6090 or
Cross connector ref. 6101
max. f. 0.40 kN
Recommendation of
dowels to be used:
adm. metal dowels with
M6 internal screw thread
and corresponding
M6 screws – see
detail page 29.
6204 1.6 5 0.4 100
with nut, SW 8,
M 5 x 16 mm,
for slotted metal hanger
Spring clip galvanised, for spring
suspension of timber battens
6129 – 0.70 1.8 250
max. f. 0.10 kN
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 7

Profiles and accessories
for suspended ceilings Approved to DIN 18168/2
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Direct hanger to fix
C-ceiling profiles, galvanised
C-ceiling profiles galvanised,
(to DIN 18182/1) for plasterboard fixing
C-ceiling profile galvanised,
(to DIN 18182/1) for plasterboard fixing
6157 12.5 0.9 5.8 100
125 x 60 x 30
max. f. 0.40 kN
5116
5120
5118
5119
5125
400
400
310
260
118.5
83.5
78.5
0.70
0.60
0.60
0.60
0.60
66.0
57.0
57.0
57.0
57.0
12
12
16
units
CD 60–07
CD 60–06
CD 60–06
fixed size 118.5 cm
CD 60–06
fixed size 83.5 cm
CD 60–06
fixed size 78.5 cm
5117 400
310
260
0.60 57 12
accessory see page no. 12
U-connection profile galvanised,
for C-ceiling constructions
5168 300 0.60 46.9 16
CD 60-06 with round return
Direct hanger to fix
C-ceiling profiles galvanised
6159
6166
6167
6169
20
12.5
12.5
6.5
0.9
0.9
0.9
0.88
8.0
5.7
5.8
3.3
100
100
100
100
200 x 60 x 30
flat type
125 x 50 x 30
to fix timber battens 30 x 50 mm
125 x 60 x 30
flat type
65 x 60 x 30
flat type
5121 400 0.60 57.0 12
without mesh
U-connection profile galvanised,
for C-ceiling constructions
5244 300 0.60 38.0 16
5128 400 0.60 57.0 12
without mesh
and middle bead
U-connection profile galvanised,
pre-cut at one side
5242 350 0.60 38.0 8
for connections to
curved ceilings
max. f. 0.40 kN
Direct hanger to fix
C-ceiling profiles, galvanised
6160 12.5 0.9 7.2 100
125 x 60 x 30
with reduction of vibrations
U-connection profile galvanised,
pre-cut at both sides
5243 350 0.60 38.0 8 for concave/convex
horizontal connections
at walls/columns
max. f. 0.40 kN
8
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Approved to DIN 18168/2
Profiles and accessories
for suspended ceilings
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
E-connection profile galvanised,
for C-ceiling constructions
Adjustable direct fixing System for
C-ceiling profile ref. 5120, galvanised
Nonius hanger galvanised,
for C-ceiling profiles
5158 300 0.60 75.4 8
6110 – 1.00 13.0 100
with two adjusting clamps
in two parts
6012 12.5 1.2 4.8 100
6,5 x 20
U-connection profile galvanised, for
C-ceiling construction at same level
5179 300 0.60 51.0 16
for screwing to timber
beams use washer
adm. f. 0.25 kN
adm. f. 0.25 kN
Click-Fix-Rail runner for direct fixing
of C-ceiling profiles, galvanised
Nonius hanger galvanised,
for C-ceiling profiles
6093 – 1.00 2.8 100
ø 6,5 x 9
6014 12.5 0.70 5.3 100 incl. saftey bracket
Hat-ceiling profile galvanised,
for direct plasterboard fixing
5114 400
500
0.60 47.1 10
Sicherungsbügel
ist
nach der
Montage
umzubiegen.
U-connection profile galvanised,
for hat-ceiling profile ref. 5114
5167 300 0.60 34,0 12
pre-bent upon request
CD-Nonius hanger galvanised,
for C-ceiling profiles ref. 5116–5120
6018 13 1.2 5.4 100
max. f. 0.40 kN
130
Delivery flat
adm. f. 0.40 kN
Nonius hanger galvanised,
for UA-50-2.0 profile ref. 5129
6013 13.5 0.70 5.3 100 incl. saftey bracket
Safety
clamps
must
be turned
after
installation
Hat spring rail
galvanised
5007 400 0.6 69 10 60 x 27
Delivery flat
adm. f. 0.40 kN
adm. f. 0.40 kN
with profile
ref. 5120
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 9

Profiles and accessories
for suspended ceilings Approved to DIN 18168/2
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
CD-hanger with special spring,
galvanised
CD-hanger for slotted strip galvanised,
for C-ceiling profiles ref. 5116–5120
Cross-connector for C-ceiling
profiles, galvanised, ref. 5120 or 5116
6038 10 1.2 5.9 100
for fixing of wire from the
side, for C-ceiling profiles
ref. 5116–5120
6059 10 1.2 4.9 100
6101 – 1.0 5.4 100
adm. f. 0.40 kN
with ref. 5120
6061 9 1.5 3.1 100
adm. f. 0.40 kN
with ref. 5120
Slotted suspension hanger
galvanised, for C-ceiling profiles
Angle-connector galvanised,
for C-ceiling profiles
6090 – 1.0 2.0 100
adm. f. 0.37 kN
Use cross connector
ref. 6105 for profile ref. 5117
Anchor hanger galvanised, with
tension spring for C-ceiling profiles
6034 9 1.5 4.3 100
adm. f. 0.25 kN
6094 – 0.9 1.97 100
Fix in pairs!
Press with pliers.
adm. f. 0.25 kN/pair
Flange clip galvanised
adm. f. 0.25 kN
6141 – 0.60 2.4 100
to cover steel columns and
joists suitable for ceiling
profile ref. 5116 and 5120
Rotation angle anchor galvanized,
for C-ceiling profiles
6095 - 1.0 1.95 100
Tension clip hanger galvanised,
for C-ceiling profiles
6104 12.5 0.80
Ø 4
3.7 100
for flange thicknesses
≥ 7 ≤ 28 mm
C-ceiling profile connector
galvanised
6078 8 0.60 4.3 100
adm. f. 0.25 kN/pair
always install
in pairs!
max. f. 0.15 kN
10
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Approved to DIN 18168/2
Profiles and accessories
for suspended ceilings
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Cross connector for ref. 5129, UA 50
only with C-ceiling profile ref. 5117
6100 – 0.80 4.2 100
supplied flat
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
TPS-CD-connector galvanised,
for ref. 5104
6127 11 0.60 4.8 100
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Convex or concave pre-bent C-ceiling
profile in material thickness 0,7 mm galvanised.
Due to production restrictions the profile lengths
are straight on 25 cm at both ends.
Minimum bending radius 200 cm – convex or concave.
Piece length 260 cm, 310 cm and 400 cm.
Minimum order quantity 20 pieces per length and
radius (also for repeat-orders).
CONCAVE
adm. f. 0.40 kN
TPS-spring-clip galvanised,
adjustable, with screws
6126 – 0.70 5.8 100
incl. 200 pcs.
timber screws
type FN 4.2 x 38 mm
CONVEX
TPS-CD-Profile galvanised
5104 400 0.60 49.5 12
Ø 4.5 x 7 mm
Please always state on your enquiries and orders:
quantity, piece length, radius cm, room width cm,
diameter cm, rise cm, arc length cm.
Safety cross-connector
galvanised
6116 – 1.00 5.5 100
for same level construction
– plasterboard fixing with
C-ceiling profiles ref.
5120/5116/5118/ 5119/5125
U-Connection profile galvanised,
for ref. 5104
5312 300 0.56 25.0 12
max. load
f ≤ 0,08 kN (8 kg)
per spring clip
5511
5512
5513
5514
5516
5517
5518
5519
260
260
260
260
260
260
260
260
0.70
0.70
0.70
0.70
0.70
0.70
0.70
0.70
66
66
66
66
66
66
66
66
20
20
20
20
20
20
20
20
Bend concave
Radii 200–300 cm
Radii 301–400 cm
Radii 401–500 cm
Radii > 500 cm
Bend convex
Radii 200–300 cm
Radii 301–400 cm
Radii 401–500 cm
Radii > 500 cm
5072 400 1.25 59.0 10
adm. f. 0.40 kN/pair
Arch profile galvanised, for
self-bending, as supporting profile
5521
5522
5523
5524
310
310
310
310
0.70
0.70
0.70
0.70
66
66
66
66
20
20
20
20
Bend concave
Radii 200–300 cm
Radii 301–400 cm
Radii 401–500 cm
Radii > 500 cm
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 11

Profiles and accessories
for suspended ceilings Approved to DIN 18168/2
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
C-ceiling profile galvanised,
(to DIN 18182/1) for plasterboard fixing
Main-T-profile
galvanised, white coated
5526
5527
5528
5529
5531
5532
5533
5534
310
310
310
310
400
400
400
400
0.70
0.70
0.70
0.70
0.70
0.70
0.70
0.70
66
66
66
66
66
66
66
66
20
20
20
20
20
20
20
20
Bend convex
Radii 200–300 cm
Radii 301–400 cm
Radii 401–500 cm
Radii > 500 cm
Bend concave
Radii 200–300 cm
Radii 301–400 cm
Radii 401–500 cm
Radii > 500 cm
5117 400
310
260
0.60 57 12 CD 60-06 with round return
5335
5340
5346
5343
375
360
375
360
0.41
0.41
0.41
0.41
37.0
37.0
32.0
32.0
25
25
25
25
for exposed grid system,
with fire protection
for grid 625
24 x 38
for grid 600 }
for grid 625
15 x 38
for grid 600 }
5536
5537
5538
5539
400
400
400
400
0.70
0.70
0.70
0.70
66
66
66
66
20
20
20
20
Bend convex
Radii 200–300 cm
Radii 301–400 cm
Radii 401–500 cm
Radii > 500 cm
CD-cross connector for CD ceiling
profiles with round return ref. 5117
6105 – 1.0 5.4 100
supplied flat
1
2
3
5
1 CD-profile 60-27 ref. 5120
2 Concave bend CD-profile
3 U-hanger ref. 6157
4 cross connector ref. 6101
5 steel framing screw ref. 6239
6 flat head screw with combination washer ref. 6204
7 Nonius hanger ref. 6017
8 adjusting clamp ref. 6199
9 adjusting strip ref. 6019-6029
U-connection profile ref. 5168 (45x28x27)
3
4
5
9
8
7
6
adm. f. 0.40 kN
T-cross-profile
galvanised, white coated
5336
5341
5337
5342
5348
5345
5347
5344
125
120
62,5
60
125
120
62.5
60
0.41
0.41
0.41
0.41
0.41
0.41
0.41
0.41
46.2
44.4
23.1
23.2
40.0
38.4
20.0
19.2
50
50
75
75
50
50
75
75
Other colours
on request
for exposed grid system,
with fire protection
for grid 625
for grid 600
for grid 625
for grid 600
for grid 625
for grid 600
for grid 625
for grid 600
Other colours
on request
}
24 x 38
}
15 x 38
12
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Approved to DIN 18168/2
Profiles and accessories
for suspended ceilings
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Short hanger, nonius for K 1100; 40 mm
adjustable, includes adjusting clamp
6112 – 1.2 4.2 100
Board clamp galvanised,
for 16 mm acoustic tiles
6153 – – 0.35 500
Clamping profile galvanised,
for metal cassettes
5110 400 0.6 49.0 10
Hanger galvanised, with special
tension spring for main-T-profiles
6162 11 1.5 3.4 100
max f. 0.15 kN
Wall spring
for fixing end boards
6099 – – 0.7 250
Pivot clamp
for fixing to T-rails
6584 – – 0.8 100 for 24–26 mm flange width
Connector galvanised,
for clamping profile ref. 5110
6080 10 0.6 2.0 100
Nonius hanger galvanised,
for K1100
6016 19 1.2 5.0 100
Cross connector galvanised,
for clamping profile ref. 5110
6085 – 0.6 1.4 100
adm. f. 0.15 kN
Sliding hanger galvanised,
suitable for main-T-profiles
adm. f. 0.40 kN
6065 12.5 1.5 1.9 100
for slotted metal strips
max. f. 0.15 KN
T-rail galvanised,
with smooth indent
5004 400 0.5 36.3 15
max. f. 0.15 kN
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 13

Profiles and accessories
for suspended ceilings Approved to DIN 18168/2
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Connecting pin galvanised,
for T-rails with ridge
Sliding hanger galvanised,
for T-rail
Nonius hanger galv., perforated,
for suspension of timber construction
6076 – – 0.7 100
6060 12.5 1.5 2.2 100
for slotted metal strip
6015 19 1.2 5.0 100
Hanger galvanised,
with tension spring
6033 10 1.5 3.3 100
with tension spring for
T-support rails with double
twist and clamping profile
ref. 5110
max. f. 0.15 kN
Nonius hanger galvanised
adm. f. 0.40 kN
Hat profile galvanised
6017 17 1.2 5.0 100
for arch-profile ref. 5072
and rail ref. 5016
5143 300 0.6 23.1 15
Nonius hanger galvanised,
for T-rail/clamping profile
6011 19 1.2 5.0 100
max. f. 0.25 kN
Pivot clip for timber panels, black,
suitable to ref. 5004 and ref. 5143
6131
6133
6135
6137
6139
6134
6132
–
–
–
–
–
–
–
–
–
–
–
–
–
–
1.0
1.3
1.3
1.3
1.4
1.0
1.0
500
500
500
500
500
250
250
joint groove
10 mm 5 mm
15 mm 5 mm
15 mm 7 mm
20 mm 5 mm
20 mm 7 mm
10 mm 4 mm galv.
10 mm 5 mm galv.
Hanger galv., with tension spring for
suspension of timber construction
6164 11 1.5 3.6 100
adm. f. 0.25 kN
Pivot clip for groove and tongue boards,
galvanised, for ref. 5004 or ref. 5143
Hanger galv., with tension spring for
suspension of timber construction
6165 10 1.5 3.6 100
max. f. 0.15 kN
6146
6144
6148
–
–
–
–
–
–
0.6
0.6
0.6
250
250
250
groove 3 mm
groove 4 mm
groove 5 mm
adm. f. 0.40 kN
max. f. 0.15 kN
14
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

See also brochure number 13025 “Master Works”
TRIGOFORM ® 300 AS with aluminum frames
Expanded Metal Tables
Mesh finishings
Expanded metal cassettes with aluminum frames
Profile
width of
Finishing /
expansion field
designation
Product
group
Product number
as per installation pattern / cassette dimensions
Packaging as per dimensions
. .
. . .
. . .
.
. .
. .
. . .
. . .
.
. .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
10
pieces
per
carton
6
pieces
per
carton
Ornamental mesh symmetrical
Ornamental mesh
asymmetrical
Weight per piece in kg (uncoated)
Finishing
as per profile width of
Product
group
Acoustic liners
Product number
as per installation pattern / cassette dimensions
Packaging
Hash
.
.
.
.
.
.
.
.
50 pieces per
packaging unit
Round hole
Weight per 100 pieces in kg
Clamping bars
Product
group
Product number
Weight per piece
in kg
Packaging
Length
.
Individual
Square
UNOFORM cassettes *
cassettes
Finishing / expansion field designation
Product
group
Product no. as per installation pattern / cassette dimensions
Weight
kg/piece
Weight
kg/piece
Packaging
. .
.
.
.
.
. Color white (coated)
. . .
* Profile width of the K 1100 = 24 mm
.
.
.
.
.
.
.
.
.
.
17 pieces
per carton
ML = mesh length
MB = mesh width
SB = strip length
SD = strip thickness
e.g.
finishing
R 16 x 8 x 2 x 1,0
ML MB SB SD
System UNOFORM
System TRIGOFORM ® 300 AS
Clamping bar
Unoform cassette
Acoustic liner
T-hanger
rail
(K 1100)
Expanded
metal plate
Aluminum frame
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 15

General Product Information
General Product and Installation Instruction for Our Ceiling Systems and Wide Span Beams
• The basis of the following ceiling system is DIN 18168 which is based upon ceiling weights of 0.5 kN/m 2 .
Heavier ceiling systems must be statically evaluated.
• All load information for suspended parts is based upon vertical tensile loads.
Please consult us for further static or dynamic values.
• All information is only valid with the exclusive use of orginal parts from our delivery program.
We assume no liabilty in the event of external products.
• The installation distances listed are based upon tests conducted and were then calibrated with the valid
DIN norms and additionally with the installation instructions of the ceiling lining manufacturer.
• The instructions for the ceiling lining installation must be inspected by the planner or installer themselves on
the basis of the current documents from the ceiling liner manufacturer.
• This must also be heeded in the event of installation instructions provided by us in reference to the ceiling
liner installation or in the event of additional parts for the construction not provided by us.
• In the event of installation of structures as per test certificates, the system components described within and
their construction information must absolutely be used and/or complied with.
• In the event of the planning or installation of ceiling liners, pitched roof liners or suspended ceilings on new or
renovated old wood components/wood beams, the following special instructions must be heeded:
- Wooden components/wooden joists/wooden beams can sag, contort (partially shift) due to equal and
unequal loads, e.g:
• Snow weight (roof)
• Wind suction or pressure stress
• Furnishing
• Traversal by the user/inhabitant
• Heavy installations on the flooring
- The movements named on the wooden structure could be statically and/or dynamic diverted and
transferred to the secondary construction (ceiling liners, suspended ceilings) which could lead to the
rubbing together of metal parts of the sub-construction and the deforming of the sub-construction in
conjunction with the creation of sound.
- The aspects named must be considered on the planning and execution side through appropriate measures
in the selection of the suspended ceiling system and/or in the reinforcement, bracing and diagonal
bracing of the primary construction.
- Corresponding measures are, among others:
• Diagonal bracing of the primary wood construction using appropriate measures (wood or metal strutting
in conjunction with appropriate connecting materials
• Reinforcing the primary wood construction with additional beams
• Installation of suspended ceilings or liners only after the determination of stress inducing new heavy
flooring installations
• Solid attachments of suspension system directly to wooden beams during renovation; remaining old
ceilings may need to be cut out selectively
• The use of heavier planking, e.g. ≥ 2 x 12,5 mm Gk or plaster fiber planking
• Planning and installation of wide span beam construction without connect to the primary wood construction
• Formation of moving connection to bordering components to avoid jams
- Liability for the functionality and interaction of primary and secondary constructions cannot be assumed
• The creation of suspended ceiling constructions, even with use of our wide span beams, upon request, can
only be conducted if all necessary information has been provided in writing.
We recommend the use of the checklist (catalog p. 39, special brochure p. 31). The determination takes
place using information provided to us through inspection reports and/or static calculations.
Additionally necessary static calculations, determinations, inspections, reports and similar items will be
invoice seperately after discussion and a written order placement.
This regulation affects planning for walls or other special constructions as well.
• The plans created by us must be inspected by the inquirer or employer under their own authority for
completeness and accordance with the technical requirements.
Suspended ceilings and liners, also in reference to the type of connection to the primary construction/to the
bordering components not described in all documents presented must be discussed on the planning and
execution side with the technical consultants from Protektor.
16
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Galvanised metal suspension system for plasterboards,
smooth, perforated or slotted. STANDARD CONSTRUCTION.
K 400 S
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
C-ceiling support profile ref. 5120 or 5116
C-ceiling board profile ref. 5120 or 5116
E-connection profile ref. 5158
or U-connection profile ref. 5168
profile connector ref. 6078
cross connector ref. 6101
or
angle anchor ref. 6090
Nonius hanger ref. 6018
adjusting strip ref. 6020–6029
C-ceiling profile hanger ref. 6038
suspension wire with eye
ref. 6041–6050
C-ceiling profile hanger for slotted
strip ref. 6059
slotted metal strip ref. 6001
adjusting bolt ref. 6201 or
2 adjusting anchors ref. 6199
fixing screws ref. 6204
plasterboard
approved to DIN 18168/2
10 points, which show the advantages of CD-hangers:
1. Inspected as per DN 18168/T2 with CD-profiles
with slanted C-profile ref. 5120.
2. Each hanger corresponds to the load bearing
group of 0.40 kN on tension.
3. This means 60 % more carrying capacity and
therefore 60 % more secure than hangers of the
load bearing group 0.25 kN.
4. Each CD-hanger fits to CD-profiles with diagonal
or round flange return.
5. The CD-hangers stand upright in the CD-profile
but are easy to move.
6. All CD-suspensions can be comfortably
preinstalled in the floors at the prescribed
intervals before they are attached at the height
of the ceiling suspension parts.
7. The new tension spring in CD-hanger ref. 6038
means that the suspension wire is simply clipped
into the slots, from the sides, without any difficult
threading.
8. All CD-hangers have side perforations for
screw fixing to the CD-profile in fire rated
systems if required.
9. Rigorous continuous factory testing ensures
permanent product quality.
10. The guarantee of an overall construction from
Protektorwerk inspected as per DIN 18168/T2,
along with the CD-profiles and CDaccessories.
Fixing of the CD-hanger ref. 6038 with special tension spring:
– Put the hanger into the profile at an angle of 45°, so that all three feet (1) are standing on the profile web.
– Turn the hanger until both slots (2) clip in under the flange returns.
– Pull up the hanger together with the profile and hold both spring slots (3) against the suspension wire.
– Press the suspension wire against the spring slots with the thumb of the right hand and simultaneously press the springs together using a small amount of force
so that the suspension wire is led through the spring slots and clicks into place behind the locking plates.
– See that the lower end of the suspension wire comes out at least two cm under the lower tension slot.
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 17

System 400 S
Profiles and accessories approved to DIN 18168/2
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Suspension wire Ø 4 mm
galvanised, with eye Ø 6
6041
6042
6043
6044
6045
6046
6048
6050
12.5
25
37.5
50
75
100
125
150
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
1.4
2.7
3.9
5.1
7.4
9.7
11.8
14.8
100
100
100
100
100
100
100
100
Suspension wire Ø 4 mm
galvanised, with hook
6051
6052
6053
6054
6055
6056
C-ceiling profiles galvanised,
to DIN 18182/1 for plasterboard fixing
5116
5120
12.5
25
37.5
50
75
100
400
400
310
260
4.0
4.0
4.0
4.0
4.0
4.0
0.7
0.6
1.4
2.7
3.9
5.1
7.4
9.7
66
57
100
100
100
100
100
100
CD-hanger with special spring
galvanised
6038 10 1.2 5.9 100 for fixing of wire from the
side, for C-ceiling profiles
ref. 5116–5120
12
12
CD 60–07
CD 60–06
Ø 6
also
supplied
in fixed
lengths
adm. f. 0.40 kN
Slotted metal strip galvanised,
20 x 1.5 mm, slot width 6.5 mm
6001 5000 1.5 17 coil
à
50
m
CD-hanger for slotted strip galvanised,
for C-ceiling profiles ref. 5116–5120
6059 10 1.2 4.9 100
Flat head screw galvanised,
with special square collar
6204 1.6 5 0.4 100
Angle connector galvanised,
for C-ceiling profiles
6090 – 1.0 2.0
slot width 6.5 mm
Adjusting clamp galvanised,
for Nonius suspension system
6199 – – 0.6 100 each connection:
2 pieces
100
with nut, SW 8,
M 5 x 16 mm
for slotted metal hanger
Fix in pairs!
Press with pliers.
adm. f. 0.40 kN
Adjusting strip galvanised,
for Nonius hanger
6020
6021
6022
6023
6024
6025
6026
6027
6028
6029
6019
13.5
20
30
40
50
60
70
80
90
100
170
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
2.5
3.5
5.6
7.5
9.0
10.5
12.6
15.0
16.5
17.5
31.0
100
100
100
100
100
100
100
100
100
100
50
CD-Nonius hanger galvanised,
for C-ceiling profiles ref. 5116–5120
6018 13 1.2 5.4 100
6101 – 1.0 5.4 100
5168 300 0.60 46.9 16
also
supplied
in fixed
lengths
130
adm. f. 0.40 kN
Cross-connector
for C-ceiling profiles, galvanised
adm. f. 0.37 kN
U-connection profile galvanised,
with perforation Ø 6 mm
U-connection profile galvanised,
for C-ceiling constructions
5244 300 0.60 38.0 16
Ø 7
Profile connector galvanised
6078 8 0.6 4.3 100
Self tapping screws
6205
6206
2.5
3.5
3.5
3.5
0.16 1000
0.20 1000
adm. f. 0.25 kN/pair
Type TN 3.5 x 25 mm
Type TN 3.5 x 35 mm
trumpet head, douple shank,
patented special point,
double phosphated
E-connection profile galvanised,
with perforation Ø 6 mm
5158 300 0.60 75.4 8
18
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

approved to DIN 18168/2
Galvanised metal suspension system for plasterboards,
smooth, perforated or slotted.
STANDARD CONSTRUCTION
K 400 S
Corrosion protected
system upon request
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
C-ceiling main rail Ref. 5120 or 5116
C-ceiling board rail Ref. 5120 or 5116
E-connection profile Ref. 5158
or U-connection profile Ref. 5168
profile connector Ref. 6078
cross connector Ref. 6101
or
angle anchor Ref. 6090
Nonius hanger Ref. 6018
adjusting strip Ref. 6020–6029
C-ceiling profile hanger Ref. 6038
suspension wire with eye
Ref. 6041–6050
C-ceiling profile hanger for slotted
strip Ref. 6059
slotted metal strip Ref. 6001
adjusting bolts Ref. 6201 or adjusting
clamps Ref. 6199
fixing screws Ref. 6204
plasterboard
Description and methods of suspension:
First the E-connection profile ref. 5158 will be
pegged into the walls at intervals of ca. 500 mm.
The C-ceiling board rail ref. 5120 or 5116 will be
pushed into the E-connection profile and then
attached to the suspension bracket. Maximum
suspension bracket distance from the wall, 1/3
suspension bracket distance, maximum beam
profile distance from the wall 1/3 of the allowable
plate profile span.
Running diagonally to this, the C-ceiling main rail
ref. 5120 or 5116 will pushed into the E-connection
profile from below and connection with the
suspended C-ceiling board rail with cross connector
ref. 6101 or angle anchor ref. 6090. The axis interval
of the first C-ceiling main rail from the wall is to be
determined from the installation table depending
on the type and thickness of the plate (e.g.
500 mm with 12.5 mm GK plate).
Profile rails must be arranged in an offset manner
using profile connector ref. 6078. In the event of
C-ceiling board rails, an additional suspension
bracket must used for profile rails. Angle anchors
must be bent with pliers!
There are three possibilities for suspension:
1. For low suspension height (up to appr. 500 mm)
we recommend our CD-hanger Ref. 6038 with
the respective suspension wires with eyes or
hooks Ref. 6041–6056 in the according lengths.
2. For greater suspension heights, the pressure
resistant Nonius suspension, consisting of
adjusting strips in the corresponding lengths
ref. 6020-6029 and the CD-nonius hanger
ref. 6018 are to be used, adjusting strip and
Nonius hanger are to be connected with two
adjusting clamps ref. 6199. Non self-securing
bolts and/or clamps are to be bent. By doing so,
these can be adjusted millimeter by millimeter.
3. Different suspension heights, in one ceiling area,
require assembly with slotted metal strip and
slotted suspension hanger Ref. 6059.
The slotted metal strip ref. 6001 will be cut from the
roll at the necessary length and connected to the
C-ceiling profile hanger for slotted strips ref. 6059
with two fixing screws ref. 6204.
Next the plasterboards will be affixed with drywall
screws without pre-drilling diagonally along the
board rail profiles. The screw connections and
subsequent trowel application must take place in
accordance with the installation guidelines of the
board manufacturer.
Appr. material requirements for 1 sqm ceiling,
without waste material:
plasterboards 12,5 mm
hanger distance 900 mm
centres of main rails 1000 mm
centres of board rails 500 mm
2.80 m 0,9 m C-main rail ref. 5120
{ 1,9 m C-board rail ref. 5120
0.56 pcs Connector ref. 6078
1.0 pcs C-hanger ref. 6038
1.0 pcs suspension wire ref. 6041–6056
CD-nonius hanger
ref. 6018 with
adjusting strip ref. 6020–6029
3.42 pcs angle anchor ref. 6090 or
(1.71 pcs) Cross connector ref. 6101
E-connection profile
ref. 5158 or
0.40 m U-connection profile
ref. 5168
18.5 pcs St-Screws ref. 6205
Detail:
Fixing of CD-hanger
Assembly Table:
according to DIN 18181
The above quantities are based on a ceiling area
of 10 x 10 m. As the material requirements depend
on the size of the ceiling and the local conditions,
the calculations of the exact quantities should
take these into consideration.
Tender Specification:
. . . . . m 2 suspended ceiling made from
plasterboards.
Brand . . . . thickness . . . .
Format . . . . from metal sub-construction as per
Protektorwerk structure 400 S.
The suspension height as per the construction plans
amounts to . . . . cm. Suspension takes place using
C-ceiling profile hanger ref. 6038, suspension wire
with eye/hook or Nonius hanger ref. 6018 and
adjusting strip.
C-ceiling main rail ref. 5120 or 5116 is suspended by
this hanging. Board profiles (C-ceiling board rails
ref. 5120 or 5116) run diagonally to the main rail
and are attached to the mail rail with angle
anchor ref. 6090. The rail joints as well as the hanger
must offset and an additional hanger must be
placed next to each rail joint.
The plasterboards are tightened to the rails using
drywall screws without pre-drilling.
The plasterboards are positioned diagonally and
offsets to the board profiles. The positioning and rail
distance are to be conducted as per DIN 18181.
The lengthwise and diagonal joints must be
spackled and sanded as per the guidelines of the
plasterboard manufacturer.
board- hanger centres of centres of
thickness distance main rails board rails
mm mm mm mm
Perforated and
slotted boards all 900 1000 320
Plasterboard 9.5 900 1250 420
panels 12.5 900 1000 500
2 x 12.5 750 1000 500
20 750 1000 750
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 19

System 400 H
Profiles and accessories approved to DIN 18168/2
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Suspension wire Ø 4 mm
galvanised, with eye Ø 6
6041
6042
6043
6044
6045
6046
6048
6050
12.5
25
37.5
50
75
100
125
150
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
1.4
2.7
3.9
5.1
7.4
9.7
11.8
14.8
100
100
100
100
100
100
100
100
Suspension wire Ø 4 mm
galvanised, with hook
6051
6052
6053
6054
6055
6056
12.5
25
37.5
50
75
100
4.0
4.0
4.0
4.0
4.0
4.0
1.4
2.7
3.9
5.1
7.4
9.7
100
100
100
100
100
100
Ø 6
CD-hanger with special spring
galvanised
also
available
in fixed
lengths
6038 10 1.2 5.9 100 for fixing of wire from the
side, for C-ceiling profiles
ref. 5116–5120
Slotted metal strip galvanised,
20 x 1.5 mm
6001 5000 1.5 17 coil
à
50
m
CD-hanger for slotted strip galvanised,
for C-ceiling profiles ref. 5116–5120
6059 10 1.2 4.9 100
width of slotted hole 6.5 mm
Adjusting strip galvanised,
for nonius hanger
6020
6021
6022
6023
6024
6025
6026
6027
6028
6029
6019
13.5
20
30
40
50
60
70
80
90
100
170
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
2.5
3.5
5.6
7.5
9.0
10.5
12.6
15.0
16.5
17.5
31.0
100
100
100
100
100
100
100
100
100
100
50
CD-Nonius hanger galvanised,
for C-ceiling profiles ref. 5116–5120
6018 13 1.2 5.4 100
ø 7
also
availabe
in fixed
lengths
adm. f. 0.40 kN
130
C-ceiling profiles galvanised.
(to DIN 18182/1) for plasterboard fixing
5116
5120
5118
5119
5125
400
400
310
260
118.5
83.5
78.5
0.70
0.60
0.60
0.60
0.60
66.0
57.0
57.0
57.0
57.0
12
12
16
units
CD 60–07
CD 60–06
CD 60–06
fixed size 118.5
CD 60–06
fixed size 83.5
CD 60–06
fixed size 78.5
adm. f. 0.40 kN
Flat head screw galvanised,
with special square collar
6204 1.6 5 0.4 100
Self tapping screws
6205
6206
2.5
3.5
3.5
3.5
0.16 1000
0.20 1000
with nut, SW 8,
M 5 x 16 mm
for slotted metal hanger
Type TN 3.5 x 25 mm
Type TN 3.5 x 35 mm
trumpet head, douple shank,
patented special point
double phosphated
Adjusting clamp galvanised,
for nonius suspension system
6199 – 0.6 100
adm. f. 0.40 kN
each connection:
2 pieces
Safety cross-connector
galvanised
Profile connector galvanised
U-connection profile galvanised, for
C-ceiling construction at same level
6116 – 1.0 5.5 100
for C-ceiling profiles
ref. 5120/5116/5118/5119/
5125
6078 8 0.60 4.3 100
5179 300 0.60 51 16
adm. f. 0.40 kN/pair
20
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

approved to DIN 18168/2
Galvanised metal suspension system at same level
for plasterboards
smooth, slotted or perforated
K400 H
1
2
3
4
5
6
7
CD-nonius hanger
Ref. 6018
main rail
Ref . 5120
cross connector
Ref . 6116
cross rail
Ref . 5118 or Ref. 5119
U-connection profile
Ref . 5179
adjusting strip
Ref . 6020–6029
Adjusting bracket ref. 6201
or 2 adjusting clamps ref. 6199
Description and methods of suspension:
First the U-connection profiles ref. 5179 will be
anchored to the walls at intervals of 500 mm. The
cross profile is clipped over the exposed cross
connector.
The cross profile ref. 5118 will be clipped into the
supporting profile, which is hung at intervals of 1250
mm, using cross connectors which are pushed into
the cross profile at intervals of 500 mm. The rail joints
of main rails ref. 5120 are connected with the
C-connector ref. 6078. Anchor U-connection
profiles at intervals of 250 mm. Maximum
suspension distance from the wall = 250 mm.
The plasterboards will be anchored with selfcutting
drywall screws of the size 3.5 x 25 mm or
3.5 x 35 mm using screw driver on the C-ceiling
profile.
There are three possibilities for suspension:
1. CD-hanger with tension spring Ref. 6038 and
suspension wire with eye Ref. 6041–6050
(125–1500 mm long).
2. Slotted CD-hanger Ref. 6059 for suspension with
slotted metal strip 20 x 1.5 mm Ref. 6001. The
metal strip has to be connected to the slotted
CD-hanger with two adjusting bolts M 5 x 15 mm
Ref. 6204.
3. CD-nonius hanger ref. 6018 and adjusting strip
ref 6020-6029 (150-1000 mm long). Nonius
hanger and adjusting strip must be connected
to each with an adjusting bracket and/or
2 adjusting strips or 2 adjusting nails. Pegs and/or
clamps which are not self-securing must be
bent. A rigid suspension will be created with this
construction which can be adjusted exactly up
to 1 mm.
Hangers and rail joints have to be staggered. An
additional hanger has, generally, to be used at the
rail joints.
Appr. material requirements for 1 sqm ceiling,
without waste material:
plasterboard 12.5 mm
hanger distance 850 mm
centres of main rails 1250 mm
centres of cross rails 500 mm
0.40 m U-connection profile Ref. 5179
0.70 m C-ceiling profile Ref. 5120
1.52 pcs cross profile Ref. 5118
2.85 pcs cross connector Ref. 6116
0.14 pcs C-connector Ref. 6078
0.77 pcs CD-Nonius hanger Ref. 6018
0.77 pcs adjusting strip Ref. 6020–6029
1.60 pcs adjusting clamp Ref. 6199 or
0.8 pcs adjusting bracket Ref. 6201
18.5 pcs St-screws Ref. 6205
These quantities are based on a ceiling area of
10 x 10m. As the material requirements depend on
the size of the ceiling and the local conditions, the
calculations of the exact quantities should take
these into consideration.
Detail: cross connection
Assembly table:
according to
DIN 18181
Tender Specification:
. . . . . m 2 suspended ceiling made from
plasterboards.
Brand . . . . thickness . . . . mm
Format . . . . on metal sub-construction as per
Protektorwerk structure 400 H. The suspension
height, as per the construction plans, amounts
to . . . . cm. Suspension takes place using
CD-nonius hanger ref. 6018, and adjusting strip or
CD-hanger with tension spring ref. 6038 with
suspension wire with eye/hook.
C-ceiling profile ref. 5120 is suspended by this
hanging.
Cross profiles ref. 5118 run diagonal to the ceiling
profiles which are attached through cross
connectors to the ceiling profile. The rail joints as
well as the hanger must offset and an additional
hanger must be placed next to each joint for
rigidity. The plasterboards are tightened to the rails
using drywall screws without pre-drilling.
The plasterboards are positioned diagonally and
offsets to the cross profiles.
The positioning and rail distance are to be
conducted as per DIN 18181.
The lengthwise and diagonal joints must be
spackled and sanded as per the guidelines of the
plasterboard manufacturer.
Board thickness hanger distance centres of centres of
mm mm main rails mm board rails mm
perforated and
slotted boards all 850 1250 320
plasterboard 9.5 850 1250 420
panels 12.5 850 1250 500
2 x 12.5 750 1250 500
20.0 750 1250 750
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 21

System 400 D
Profiles and accessories approved to DIN 18168/2
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Adjustable direct fixing System
for C-ceiling profiles, galvanised
CD 60-06 to DIN 18182/1
for plasterboard fixing
Profile connector galvanised
6110 – 1.00 13.0 100 two parts with two
5120 400 0.60 57 12
adjusting clamps
310
260
6078 8 0.60 4.3 100
6,5 x 20
adm. f. 0.25 kN
For screwing to timber
beams use washer!
U-connection profile galvanised,
with punching Ø 6 mm
5168 300 0.60 46.9 16
Self tapping screws
6205
6206
2.5
3.5
3.5
3.5
0.16 1000
0.20 1000
Type TN 3.5 x 25 mm
Type TN 3.5 x 35 mm
trumpet head, douple shank,
patented special point
double phosphated
Screw for timber construction with
Pozidrive, slot size 2, galv., coated
6212
6213
4.5
7.0
5
5
0.48
0.72
250
250
for suspension from timber
structure
5 x 45 mm
5 x 70 mm
U-connection profile galvanized
for CD-structures
5244 300 0.60 38.0 16
PVC profile for movement joints,
white, with elastic centre parts
3750 7500 1.0 7.5 1
coil
à
75 m
U-connection profile galvanized
for hat ceiling profile ref. 5114
5167 300 0.60 34.0 12
Hat ceiling profile galvanised,
for direct fixing in DG-extension
5114 400
500
0.6 47.1 10
Click-fix-rail runner for
direct fixing, CD-profile, galvanized
6093 – 1.00 2.8 100
ø 6.5 x 9
max. f. 0.40 kN
Detail:
Installation of direct suspension
1. fix the upper part
on the ceiling
2. slide the adjusting
piece into the profile
3. put the profile and the adjustable
piece into the suspension piece
4. adjust height and fix
with adjusting clamps
Please note:
When fixing to timber means, use washers in sizes R 5.5/18/2 or R 6.6/22/2 acc. DIN 440.
When using dowels approved for concrete ceilings the washers are normally integral.
Min. suspension height
to bottom of C-profile
= 59 mm
Max. suspension height
to bottom of C-profile
= 108 mm
22
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

approved to DIN 18168/2
Galvanised, directly fixed adjustable metal system
for plasterboards,
smooth, perforated or slotted
K400 D
1
2
3
4
fixing part ref. 6110
Alternative: Click-fix rail
runner ref. 6093 for direct
fixed or U-hanger
ref. 6157 (see page 8 for
additional U-suspension
heights)
ceiling profile ref. 5120
plasterboard
U-connection profile ref. 5168
Alternative: ref. 5244
2 1 3 4
Description and methods of suspension:
After installation of the circulating U-connection
profile ref. 5168, the upper parts are to be attached
to the raw ceiling at intervals of 1000 mm
(with 12.5 mm plasterboard). The adjusting parts
are clipped into the ceiling profile ref. 5120 at
intervals of 1000 mm. The ceiling profiles which are
now equipped with adjusting parts are pushed into
the U-conneciton profiles at the wall connection
and the adjusting parts in the upper section are
finally clicked into place. The ceiling profiles can
now be adjusted to the necessary height and this
position is adjusted by placing two adjusting
clamps through the nonius holes of the upper and
adjusting parts. Rail joints are connected offset
with connector ref. 6078 and equipped with an
additional direct attachment.
Maximum suspension distance from the wall = 330 mm.
Finally, the 12.5 mm plasterboards are attached
with drywall screws type St 3.5 x 25 mm ref. 6205
diagonal to the rails.
The attachment and spackling of the boards must
take place as per the guidelines of the
plasterboard manufacturer.
Detail:
Attic removal with
hat ceiling profile ref. 5114
Appr. material requirements
without waste material for 1 sqm sub-ceiling
plasterboards 12.5 mm
hanger distance 1000 mm
centres of board profiles 500 mm
0.4 m U-connection profile ref. 5168
1.9 m C-ceiling profile ref. 5120
1.52 pcs adjust. suspension ref. 6110
0.38 pcs connector ref. 6078
18.5 pcs St-screws ref. 6205
These quantities are based on a ceiling area of
10 x 10 m. As the material requirements depend on
the size of the ceiling and the local conditions, the
calculations of the exact quantities should take
these into consideration.
Tender Specification:
. . . . . m 2 directly installed sub-ceiling from
plasterboard, brand . . thickness . . . . . mm, with
adjustable metal sub-structure as per
Protektorwerk structure 400 D. Hanger interval
. . . . . mm, rail interval . . . . . mm.
The fixing of the ceiling profile to the raw ceiling
must take place with adjustable suspension
ref. 6110 (adjustment range from UK raw ceiling to
UK ceiling profile of 59–108 mm).
U-connection profiles ref. 5168 are to be installed
as edge connectors.
Rail joints are to connected in an offset manner
with connector ref. 6078 and provided with an
additional suspension.
The plasterboards are to be attached to the
C-ceiling profiles with drywall screws type St with
pre-drilling positioned diagonally and subsequently
be spackled and sanding to a readyto-paint
condition.
The guidelines of the plasterboard manufacturer
regarding sub-structures, attachment and
spackling for a ready-to-paint condition must
be followed.
U-hanger
ref. 6157
SB-screw
ref. 6239
C-ceiling profile ref. 5120
plasterboard
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 23

System 400-TPS-25
Profiles and accessories approved to DIN 18168/2 + 4102
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
TPS-CD-Profile,
galvanised
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
TPS-CD-Connector,
galvanised
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
PVC movement joint profile
white, with flexible centre part
5104 400 0.60 49.5 12 6127 11 0.60 4.8 100
3750 7500 1.0 7.5 1
coil
à
75 m
TPS-Spring-clip, adjustable
galvanised
U-Connection-profile,
galvanised
Self tapping screws
6126 – 0.70 5.8 100
5312 300 0.56 25.0 12
6205
6206
2.5
3.5
3.5
3.5
0.16 1000
0.20 1000
Type TN 3.5 x 25 mm
Type TN 3.5 x 35 mm
trumpet head, douple shank,
patented special point
double phosphated
ø 4.5 x 7 mm
incl. 200 pieces timber
screws ref. 6242
type FN 4.2 x 35 mm
max. load
f ≤ 0.08 kN (8 kg)
per spring clip
Fiber board screw, phosphated
with Philip’s and slot head
6241 3.0 3.9 0.18 1000 3.9 x 30 mm
System drawing:
3
2
5
Ref. 3750
at the edge
1
Press bracket against screw head!
Direct fixing
Adjusted fixing
Note: The general product information (catalog page 16) must be noted.
24
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

approved to DIN 18168/2 + 4102
Galvanised impact sound absorption profile system,
fixing height 25 mm, adjustable, for boarding with
gypsum boards or gypsum-fibre boards
K400
TPS-25
1
2
3
4
5
TPS-CD-profile ref. 5104
TPS-spring clip ref. 6126
Timber screw FN 4.2 x 35 mm
TPS-CD connector ref. 6127
PVC-movement bead
ref. 3750 or
PVC-edge profile
ref. 3766 with joint filler
Purpose:
Profile- and fixing-system to improve the impact
sound absorption specially with timber joist ceiling
constructions in prefab houses, in timber skeleton
constructions and refurbishment of old houses. The
low construction height of 25 mm corresponding to
conventional timber batten fixing for cladding
does not need any change of design for the
utilisation of TPS-25 instead of timber battens.
If necessary the spring clip can be adjusted by
turning the timber screws up to 5 mm in the height.
Two punched safety anchors are integrated into
the TPS-spring clip which prevent bending of the
spring latches and thus a loosening of the TPS-CDprofile
in the event of too heavy a load due to
ceiling lights or similar objects.
Fixing :
The division of the profiles takes place in installation
intervals of 500 mm depending upon planking. The
beam interval should not exceed 700 mm. In the
event of greater beam intervals, the axis interval
of the TPS-CD-profiles to the load must be
correspondingly shortened. The U-connection
profile ref. 5312 can be placed at the wall
connection as an installation aid.
TPS-CD-profile ref. 5104 will always be installed
diagonal to the beams. To do so, the necessary
number of TPS-spring clips ref. 6126 will be clipped
into the profile and screwed into each wooden
beam with the accompanying timber screws.
Further technical information regarding impact
sound absorption, fixing distances and material
requirements can be obtained from our special
brochure “TPS-25–Adjustable” which we will mail to
you upon request.
Many more test results with different floor
constructions as dry floor pavement or screed
floors are available..
Profile joints within the middle of the field are to be
avoided, as is the arrangement of multiple profile
joints next to each other. Profile cuts must be
conducted cleanly in order to avoid jagged
edges on the profile ends. If necessary, the profile
ends may have to be pressed together. Following
this, the fixing of the planking diagonal to
the TPS-CD-profiles with the drywall screws
corresponding to the planking thickness takes
place.
Contact between the drywall screws and the clips
is to be avoided, as is contact to the upper
edgesof the profiles. It is recommended that the
ceiling area be continually tested for the creation
of noise during the planking of the ceiling area
and, if necessary, improved.
The plank connections to the bordering
components should be spackled thickly.
Alternatively, the attachment and spackling of
PVC-movement bead ref. 3750 above the
corner on the ceiling and/or wall planking is
recommended.
Adjusting:
After screwing of the TPS-spring clip bend the two
vertically positioned brackets towards the screw
heads by hammer stroke. Afterwards the screws
can be drawn back, the TPS-spring clip follows the
movement.
The maximum adjustment distance for the
included timber screws 4.2 x 35 mm is 5 mm.
Larger unevenness require a pre-installation of a
basic structure from boards or wooden slats.
It is generally recommended that the TPS-clip be
secured after adjustment again noise formation,
e.g. by placing appropriate material.
Tender Specification:
Deliver and install an impact sound absorption
profile system TPS-25 from Protektorwerk.
On a new/old wooden beam ceiling
Beam dimensions…………………………………mm
Beam interval ……………………………………..mm
TPS-CD-profile interval……………………………mm
for planking with ……… mm gypsum boards type
GKB, GKF or gypsum-fiber boards brand ………
as simple, double planking.
U-connection profiles ref. 5312 are to be installed
as edge connectors.
Rail joints are to be conducted offset with TPS-CD
connector ref. 6127.
The plasterboards are to be attached to the
C-ceiling profiles with drywall screws type St
with pre-drilling positioned diagonally and
subsequently be spackled and sanding to a
ready-to-paint condition.
Gypsum-fiber boards are to be correspondingly
installed with gypsum-fiber board screws.
The guidelines of the gypsum board manufacturer
regarding sub-structures, attachment and
spackling for a ready-to-paint condition must
be followed.
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 25

System 400 arch
Profiles and accessories approved to DIN 18168/2
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Adjusting strip galvanised,
for Nonius hanger
Arch profile galvanised, for
self-bending, as supporting profile
U-connection profile galvanised,
pre-cut at one side
6020
6021
6022
6023
6024
6025
6026
6027
6028
6029
6019
13.5
20
30
40
50
60
70
80
90
100
170
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
2.5
3.5
5.6
7.5
9.0
10.5
12.6
15.0
16.5
17.5
31.0
100
100
100
100
100
100
100
100
100
100
50
Ø 7
also
available
in fixed
lengths
5072 400 1.25 59 10
Hat-ceiling profile galvanised,
for plasterboard fixing
5114 400
500
0.60 47.1 10
5242 350 0.60 38.0 8
Self tapping screw
6205 2.5 3.5 0.16 1000
Type TN 3.5 x 25 mm
trumpet head, douple shank,
patented special point
double phosphated
Nonius hanger galvanised,
with Ø 6,5 mm perforation
6017 17 1.2 5.0 100
Steel framing screw with truss head
6236 1.3 4.2 0.18 1000
pre-bent upon request
and cross slot, galvanised,
self-drilling point
for material
thicknesses from
0.70 up to 2.25 mm
∅ head: 12 mm
4.2 x 13 mm
Direct hanger
6157 12.5 1.0 5.8 100 125 x 60 x 30 mm
to be used
as distance
holder
adm. f. 0.25 kN
Adjusting clamp for Nonius
suspension system, galvanised
6199 – – 0.6 100
Flat head screw galvanised,
with special square collar
6204 1.6 5 0.4 100
mit nut, SW 8,
M 5 x 16 mm
Fixing table:
Board Distance Distance Hat-ceiling Hanger
Boards thickness Arch profile centres profile centres distance
mm mm mm mm
Special
plaster boards 1 x 6 750 300 600
to be 2 x 6 750 300 600
bend dry
R ≥ 600 mm
Plaster boards 1 x 9.5 750 300 ≤ 420 600
1 x 12.5 750 300 ≤ 500 600
2 x 12.5 625 300 ≤ 500 500
acc. radius
26
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

approved to DIN 18168/2
Galvanised metal subconstruction in arch form
for gypsum plasterboards
K400
Bogen
5
2
3
4
1
Alternative:
C-ceiling profiles
pre-bent at the factory
(see pages 11 and 12)
6
7
1
2
3
4
5
6
7
Nonius hanger ref. 6017
Adjusting strip ref. 6020–6029
Adjusting clamp ref. 6199
Arch profile ref. 5072
Hat-ceiling profile ref. 5114
Arch model
Mounting lath
Description and methods of suspension:
The arch profiles are bent on site over a vault
model according to the required radius. The fixing
is effected to wall and ceiling with nonius hangers
ref. 6017 and adjusting strips ref. 6020–6029 at a
distance according to opposite chart. Please also
find in this chart the centres of the arch profiles
referring to provided boards.
Running diagonally to the arch profiles the hat
ceiling profiles ref. 5114 are screwed to the arch
profiles with 2 self drilling screws ref. 6236 in a
distance corresponding to the boards. For small
arch radii it is necessary to reduce the distance
between the hat ceiling profiles.
Finally the boards are screwed to the hat ceiling
profiles. According to type of boards and arch
form, the boards can either be laid on the fixing
system in dry condition, bent and screwed on, or
they have to be pre-bent over a vault model. Do
not screw wet boards directly to the profiles.
Bending, fixing and jointing of the boards should
be according to manufacturer’s instructions.
Approx. material requirement:
The material requirement depends on the chosen
boards, the arch form and its dimensions. Therefore
the material requirement has to be calculated
individually for each project.
A general indication of material requirement is not
possible.
You will find detailed installation instructions with
notes for material determination in our special
brochure “Subconstructions for arched roofs”,
which we are happy to send you upon request.
Tender Specification:
Delivery and preparation of a sub-ceiling in arch
form for planking with gypsum plasterboards/
gypsum-fiber boards thickness. . . . mm,
brand . . . . , on galvanized metal subconstruction
of the Protektorwerk structure “K 400 Bogen”.
Room length . . . . mm, room width . . . . mm, room
height . . . . mm, arch radius. . . . mm, cut
height . . . . , suspension height until lower edge
of arch vertex . . . . mm, type of existing raw
ceiling . . . .
The suspension an arch profile ref. 5072, pre-bent
with a bending gauge must take place with
pressure resistant Nonius hangers ref. 6017 and
adjusting strips in the necessary lengths.
Fixing details:
Hat ceiling profile
ref. 5114 screwed to
arch profile ref. 5072
4
5
Hat-ceiling profile ref. 5114 must be attached to
the arch profiles with 2 self drilling screws ref. 6236
running diagonally lengthwise. The axis interval
should be selected in accordance with the
planking and the arch form.
Next the planking is attached diagonally to the
hat-ceiling profiles either dry or pre-bent for
spackling and sanding to make it ready-to-paint.
The bending, attachment and spackling must
take place as per the guidelines of the board
manufacturer.
6017
6204
1
A↵
5072
4
A↵
6236 5114 5
Section A–A
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 27

Details for subconstructions with plasterboards
Hat ceiling profile ref. 5114
Minimum construction heights of different direct fixing systems
CD ceiling profile ref. 5120 and
profile runner ref. 6093
CD ceiling profile ref. 5120 and profile runner
ref. 6093 and hat ceiling profile ref. 5114
Hat ceiling profile ref. 5114
Gypsum plaster board
Self tapping screw ref. 6205
Adjustable direct fixing.
Please refer to system K 400 D, page no. 24/25
CD ceiling profile ref. 5120
Profile runner ref. 6093
Gypsum plaster board
Self tapping screw ref. 6205
CD ceiling profile ref. 5120
Profile runner ref. 6093
Steel framing screw ref. 6239
Hat ceiling profile ref. 5114
Gypsum plaster board
Self tapping screw ref. 6205
UA-Profile 50-20 ref. 5129 used as wide span profile,
CD ceiling profile ref. 5117 fixed with cross connector ref. 6100
Maximum span width of the UA profile ref. 5129 available upon request
UA profile ref. 5129 suspended
with nonius hanger ref. 6013
IP-beam
Fixing clamp set ref. 6590
U reinforcing channel
ref. 5129
Fixing clamp must be
bent after installation.
CD cross connector
ref. 6100
C ceiling profile ref. 5117
Fitting out an attic with
hat profile ref. 5114
connection of attic incline to ceiling with hat
profile ref. 5114 and PVC movement joint
profile ref. 3750
board joints on hat profile
ref. 5114
28
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Fixing details
Anti-vibration hanger ref. 6039 –
showing different assembly possibilities
U hanger ref. 6160 with reduction of vibration
Dowel recommendation:
Approved metal dowel with M 6 internal
screw thread and appropriate M 6 screw
Suspension
wire with
eyes
M 5 x 16
(on site)
slotted
metal strip
or slotted
metal
hanger
Steel framing screw
ref. 6239
C-ceiling profile ref. 5120
Gypsum plaster board
approved for fire rated ceilings
Gypsum plaster board ceiling connection with shadow joint at round wall
or round pillar without fire proofing
with offset connection for fire proofing
Cladding with plasterboards of steel construction with clip ref. 6141 and ceiling profiles ref. 5120 or ref. 5117 as subconstruction
suitable for steel construction with flange thickness ≥ 7 until ≤ 28 mm
5120
6141
5312
5312
6141
6141
5120 5120
GKP
cladding of a steel column cladding of a steel joist cladding of joist
Regarding fixing system and cladding thickness for fire protection, refer to board manufacturer`s instructions!
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 29

Excerpt from our Brochure
WIDE SPAN BEAMS
Please ask for
our complete
wide span beam brochure
(Number 13006).

GENERAL INFORMATION
During renovation, but also frequently in newly constructed
buildings, it becomes necessary to free yourself from the
attachment possibilities to the raw ceiling or to existing roof or
ceiling structures.
The reason for this could be, for example:
• A no longer loadable primary structure,
• Sound insulation technical requirement which make a separation
of construction elements necessary,
• Too large of intervals between load-bearing construction elements
to be able to install standard ceiling systems under them.
In all of these and many other cases, PROTEKTOR
WIDE SPAN BEAMS offer a solution.
On the following pages, the system
components of the three wide span beam
system and the principle uses, divided
by system MINI, MIDI and MAXI are
presented.
You will find values regarding possible
loads and accompanying span widhts
in the wide span beam catalog. The
details regarding the respective systems
(connection details, et cetera) are also
presented there, as well as tender
specification text for each wide span
beam system.
As not only the span width plays a role in the selection of a
system, but also the load that ultimately must be absorbed,
PROTEKTOR has developed tailor made system for various
loads.
Divided into three different load classes,
MINI ≤ 0.30 kN/m² (up to 30 kg/m²)
MIDI ≤ 0.65 kN/m² (up to 65 kg/m²)
MAXI ≤ 2.50 kN/m² (up to 250 kg/m²)
PROTEKTOR offers a suitable system for every need with
a detailed solution specifically for it.
Tabular values and load information
are only valid when
PROTEKTOR products are used,
see wide span beam catalogue.
In addition, the WIDE SPAN BEAM SYSTEMS MINI,
MIDI and/or MAXI offer the possibility of creating room-in-room
structures, such as control rooms or examination rooms.
Subject to technical changes!
© Protektorwerk 2007
31

s y s t e mMINI
Load ≤0.30 kN/m² (up to 30 kg/m²)
Ref. No.
Length/cm
Materialthickness/mm
Weight/kg 100 m/pcs
Packing pcs/lengths
Ref. No.
Length/cm
Materialthickness/mm
Weight/kg 100 m/pcs
Packing pcs/lengths
Ref. No.
Length/cm
Materialthickness/mm
Weight/kg 100 m/pcs
Packing pcs/lengths
Runners – UW 50 Connection angle
Studs CW 50
acc. to DIN 18 182-1, galvanised
for UA 50-20
acc. to DIN 18 182-1, galvanised
5230 260 0.6 58.0 8
6185 – 2.0 9.2 25
5211 250 0.6 70.6 8
400 0.6 58.0 8
260
275
300
325
Runners – UW 75
acc. to DIN 18 182-1, galvanised
5233 260 0.6 69.0 8
400 0.6 69.0 8
Runners – UW 100
acc. to DIN 18 182-1, galvanised
5234 260 0.6 80.6 8
400 0.6 80.6 8
Runners – UW 125
acc. to DIN 18 182-1, galvanised
5248 400 0.6 88.0 8
Angle profile, 50 x 40 x 1,5
galvanised
5180 300 1.5 104 10
Suspension angle profile 28 x 28 x 2
perforation Ø 6,5 mm, galvanised
5178 400 2.0 76 8
Connection angle
for UA 75-20
6183 – 2.0 16.9 25
Connection angle
for UA 100-20, galvanised
6182 – 2.0 23.4 25
Drywall screws type TN
acc. to DIN 18 182-2
6205 2.5 3.5 0.16 1000
6206 3.5 3.5 0.20 1000
6208 4.5 3.5 0.27 1000
6209 5.7 3.8 0.34 500
Wood screws 5.0 x 45/70
Poz size 2, galvanised
6212 4.5 5.0 0.48 250
6213 7.0 5.0 0.72 250
5221 Fix 0.7 85.2 8
Studs CW 75
acc. to DIN 18 182-1, galvanised
5215 250 0.6 82.0 8
260
275
300
325
350
400
450
5218 Fix 0.7 99.0 8
Studs CW 100
acc. to DIN 18 182-1, galvanised
5216 260 0.6 93.0 8
275
300
325
350
400
450
500
5219 Fix 0.7 112.1 8
Studs CW 125
acc. to DIN 18 182-1, galvanised
5141 Fix 0.6 109.0 8
Sheet metal screws 4,2 x 13
with flat head and Phillip’s head
6239 1.3 4.2 0.16 1000
32

Load ≤0.30 kN/m² (up to 30 kg/m²)
s y s t e mMINI
Ñ
É
3a
Ö
Å
Ç
Å
Å
Ç
É
3a
Ñ
Ö
UW-Connection profile
CW-support profile
Suspension angle as prevention
against lateral torsional
buckling (LTB)
UW lateral torsional buckling
(LTB) prevention lock
alternative to É
Attachment UW-Runner
Attachment means as per
manufacturer’s information
UW-/CW-connector
It is often only necessary in existing corridors to gain new
installation room for data and electrical wiring. If for reasons
of space it is not possible to position the suspension of a
ceiling, one can span the corridor directly from wall to wall with
the MINI system and attach to the boarding in the room directly
or suspended the desired sub-ceiling from this.
The MINI system consists of standard CW-stud which,
depending upon the requirements of the span width and the load
to be absorbed are either simply spanned or spanned back to
back from wall to wall.
UW-Runners inserted into the upper edge of the CW-studs serves
as wall support and can be attached and secured using screws.
Alternatively, the CW-stud can be placed on wall angle profile or
attached using UA-connection angles.
If simple CW-studs are used, one tipping prevention must be affixed
using the upper suspension angle and/or prevention against
UW-lateral torsional buckling (LTB) catch.
UW-Runner 0.6 mm
Maximum absorbable point load of the wall connections
Dependent upon the support system and the type of connection
UW-Runner 0.6 mm
Connection profile 1.5 mm
0.05 kN* 0.07 kN* 0.08 kN* 0.11 kN* 0.35 kN 0.50 kN 0.32 kN 0.40 kN
* With continuous attachment to the boarding with the
connection profiles in intervals e ≤ 150 mm, the maximum point
load increases to 0.30 kN.
Crimping, riveting and/or using screws
Screw connection with underlying disc Ø16
33

s y s t e mMIDI
Load ≤0.65 kN/m² (up to 65 kg/m²)
Ref. No.
Length/cm
Materialthickness/mm
Weight/kg 100 m/pcs
Packing pcs/lengths
Ref. No.
Length/cm
Materialthickness/mm
Weight/kg 100 m/pcs
Packing pcs/lengths
Ref. No.
Length/cm
Materialthickness/mm
Weight/kg 100 m/pcs
Packing pcs/lengths
U 77 Wall fixing angle C 77
U-connecting- or support-rail, galvanised for C 77 and C 102, galvanised Wide span profile, galvanised
5137 400 2.0 250 1
500
600
U 102
U-connecting- or support-rail, galvanised
5138 400 2.0 350 1
500
600
700
Connection angle
for UA 50-20
6185 – 2.0 9.2 25
Connection angle
for UA 75-20
6183 – 2.0 16.9 25
Connection angle
for UA 100-20, galvanised
6182 – 2.0 23.4 25
Support angle profile 70 x 50 x 4
galvanised
5502 300 4.0 312 1
83
108
for C 77
for C 102
6179 – 3.0 28.3 1
Wall fixing angle 158 x 90 x 45
galvanised
6184 – 10 72 1
Suspension angle profile, 28 x 28 x 2
Holes Ø 6.5 mm, galvanised
5178 400 2.0 76 8
Fixing set
galvanised
6203 2.0 8 2.1 100
Super TEKS screw 6.3 x 19
galvanised
6234 1.9 6.3 0.67 500
Sheet metal screws 4.2 x 13
with flat head
6236 1.3 4.2 0.18 1000
Sheet metal screws 6.3 x 19
with flat head
6233 1.9 6.3
5126 300 2.0 212
350
400
450
500
550
600
C 102
Wide span profile, galvanised
5127 300 2.0 250 1
350
400
450
500
550
600
700
800
UA 50-20
Wide span profile, galvanised
5129 260 2.0 177 4
300
350
400
450
500
UA 75-20
Wide span profile, galvanised
5130 260 2.0 199 4
300
350
400
450
500
550
600
UA 100-20
Wide span profile, galvanised
5131 260 2.0 249 4
300
350
400
450
500
550
600
UA 125-20
Wide span profile, galvanised
5132 400 2.0 287 4
Fix
77.5
102.5
48.8
73.8
98.8
123.8
Self-drilling tip for sheet thicknesses up to 6.0 mm
Special holder with bit upon request
34

Load ≤0.65 kN/m² (up to 65 kg/m²)
s y s t e mMIDI
Ñ
É
á
à
Å
Ü Ö Ç
Å
Å
Ç
É
Ñ
Ö
Ü
á
à
U-Connection profile
C-wide span beam
UA-wide span beam
Prevention against lateral torsional
buckling (LTB) ≤ 1500 mm
(e.g. suspension angle profile)
C-ceiling profile 60-27
Hat-ceiling profile
Alternative to Ö
Attachment U-profile
Connector U-/C-profile
If greater span widths are to be bridged, heavier ceiling weights
are to be considered or additional installation in the ceiling are
intended (lights, among others), the MIDI system offers freedom
in planning.
On the basis of single or doubled UA-profiles, individual profiles
or profile combinations of the C+U 77 and/or 102 profiles, ceiling
weights up to 0,65 kN/m² (65 kg/m²) can be realized.
U-Connection profiles are used as wall supports; alternatively, the
profile can also be attached with mounting angle, connection angle
and support angle profiles to construction elements.
The wide span beams are to be protected against lateral torsional
buckling (LTB) on the upper side at intervals of e ≤ 1500 mm by
suspension angles or similar devices.
Maximum absorbable point load of the wall connections
Dependent upon the support system and the type of connection
U-connection profile 2,0 mm
Angle-connection profile 4.0 mm
0.75 kN 1.00 kN 1.50 kN 2.50 kN 2.00 kN 2.40 kN 0.60 kN 1.20 kN
Screw connection
Screw connection with underlying disc Ø 16 mm
35

s y s t e mMAXI
Load ≤2.50 kN/m² (up to 250 kg/m²)
Ref. No.
Length/cm
Profile height A/mm
Weight/kg 100 m/pcs
Packing pcs/lengths
Ref. No.
Length/cm – A/mm
Materialthickness/mm
Weight/kg 100 m/pcs
Packing pcs/lengths
Ref. No.
Length/cm
Profile height A/mm
Flange width B/mm
Weight/kg 100 m/pcs
U-connection profile TA Studs C-wide span profile
1.5 mm, galvanised 4.0 mm, galvanised 1.5 mm, galvanised
4410 400 100 209 1
4540 90 4.0 36.2
4710 Fix 97 49/52 244
4415 150 267
4541 123 40.7
4715 147 49/52 302
4420 200 326
4426 250 385
A
4542 148 56.7
4543 173 59.7
A
A
40
4544 202 68.4
B
U-wide span profile
1.5 mm, galvanised
U-connection profile Connection angle AW 40 x 40 x 2/5
2.0 mm, galvanised galvanised 4419 Fix 197 48 341
4427 400 251 515 1
4530 301 593
A
40
4550 90 2.0 14.0
4551 140 21.8
4552 90 5.0 35.1
4553 140 54.6
A
C-wide span profile
2 mm, galvanised
4810 Fix 97 48/52 320
A
B
U-connection profile Suspension angle profile, 28 x 28 x 2
3.0 mm, galvanised perforation Ø 6.5 mm, galvanised
4915 400 154 587 1
4920 204 704
4925 254 820
4930 304 937
A
50
5178 400 2.0 76 8
4815 Fix 147 48/52 401
U-wide span profile
2 mm, galvanised
4519 Fix 197 48 452
A
B
A
Support angle profile 70 x 50 x 4 Super TEKS screw 6.3 x 19
galvanised
galvanised
5502 300 4.0 312 1 6234 1.9 6.3 0.67 500
U-wide span profile
2 mm, galvanised
B
4525 Fix 246 40 506
4529 296 584
A
Connection angle Sheet metal screws 4.2 x 13
2.0 mm, galvanised with flat head
6185 — 2.0 9.2 25
6236 1.3 4.2 0.18 1000
U-wide span profile
3 mm, galvanised
B
4914 Fix 147 40 514
4918 197 632
4923 247 750
4929 297 868
A
B
36

Load ≤2.50 kN/m² (up to 250 kg/m²)
s y s t e mMAXI
Ç
Å
É
Ö
Ñ
Å
Ç
É
Ñ
Ö
L-wall connection profile
Wall attachment L-angle
C-wide span profile
U-Connection profile
Suspension angle e ≤ 1500 mm
If ceiling structures are to be traversable or if, due to local
conditions the installation of a proper interim ceiling with loads up
to 2,50 kN/m² (250 kg/m²) is necessary, the MAXI system offers
the corresponding solution.
U-Connection profiles are used as wall support. Alternatively, the
profile could also be attached with connection angles and support
angle profiles to the construction elements.
If the beam are resting on a support (e.g. wall) they must be
secured against tipping with TA studs in the support area.
The prevention of lateral torsional buckling (LTB) of the support in
the field is created with suspension angles at intervals e ≤ 1500
mm. If the structure is traversable or boarding is placed on the
upper side for other reasons (e.g. span boards, OSB planking,
et cetera), the prevention of lateral torsional buckling (LTB) can
also be created by screw connections of the upper planking with
the supports.
Maximum absorbable point load of the wall connections
Dependent upon the support system and the type of connection
U-connection profile 1.5 mm
U-connection profile 1.5 mm
U-connection profile 2.0 mm
U-connection profile 3.0 mm
Angle-connection profile 4.0 mm
0.30 kN 0.35 kN available on request 0.75 kN 1.00 kN 1.20 kN 1.40 kN 2.00 kN 2.40 kN
Screw connection
Screw connection with underlying disc ø16
37

UNIVERSAL ACCESSORIES
Ref. No.
Length/cm
Materialthickness/mm
Weight/kg 100 m/pcs
Packing pcs/lengths
Ref. No.
Length/cm
Materialthickness/mm
Weight/kg 100 m/pcs
Packing pcs/lengths
Ref. No.
Length/cm
Materialthickness/mm
Weight/kg 100 m/pcs
Packing pcs/lengths
C-ceiling profile Adapter Suspension clamp
galvanised, acc. to DIN 18 182-1 for threaded bar suspension for horizontal fixing
5120 260 0.6 57.0 12
310
400
6186 — 4.0 30 1
6580 — — 1.4 100
5116 400 0.7 66.0 12
Hat-ceiling profile Suspension clamp Suspension clamp
galvanised for suspension from IP beams for horizontal fixing with tension spring
5114 400 0.6 34.0 10
500
6586 — — 27.5 1
6581 — — 22 100
5007 400 0.6 69 10
Hat-spring rail Suspension clamp Suspension clamp
galvanised for suspension from IP beams for vertical fixing
6587 — — 22 1
6582 — — 0.9 100
Click-fix-rail guide Ground plate Suspension clamp
for direct installation, galvanised perforation ø 10.5 mm, galvanised for vertical fixing with tension spring
6093 — 1.0 2.8 100
6589 — 5.0 7.1 25
6583 — — 1.7 100
Fixing clamp set M 8 x 50 Fixing clamp set M 10 x 50
for UA-profile, galvanised
for C 77/102, galvanised
6590 — — 28.0 10
6588 — — 30.0 10
38

CHECKLIST WIDE SPAN BEAMS
Fax to
PROTEKTORWERK
Telephone
Fax
Date
AD TD VL VB
Name
Telephone
Orderer / Contractor
Retailer / Customer
Company
Company
Contact Partner
Contact Partner
Street
Street
Postal Code / City
Postal Code / City
Customer Number
Telephone
Telephone
Fax
Fax
Construction Project
Delivery Address / Commission
Execution Time
Delivery Date
Length x Width in m
Ceiling Area in m²
Max. Span Width in mm
Max. Deflection in mm
Traversable NO YES ➞ Imposed Load in kg/m²
Flooring Installation NO YES ➞ Weight in kg/m²
Ceiling Installation NO YES ➞ Weight in kg
Sub-Ceiling Type
Suspension Interval in mm
Weight of Sub-Ceiling in kg
Basic Profile Interval in mm
Fire Protection NO YES ➞ Fire Resistance F-
Support
Concrete Wall Masonry Wall Metal Stud Wall
Connection to Construction Element
Concrete Wall Masonry Wall Metal Stud Wall
Suspension in Raw Ceiling
Concrete Ceiling Steel Load- Wooden Load-
Bearing Structure Bearing Structure
Remarks
P R O T E K T O R W E R K
Florenz Maisch GmbH & Co. KG
Gewerbegebiet Birkig · Viktoriastraße 58
P.O.Box 1420 · D-76571 Gaggenau · Germany
Tel. +49 (0)7225.977.0 · Fax +49 (0)7225.977.111
www.protektor.com · info@protektor.com
Stamp/Signature
39

System 500
Profiles and accessories approved to DIN 18168/2
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Suspension wire Ø 4 mm
galvanised, with eye Ø 6
Adjusting strip galvanised,
for nonius hanger
Slotted metal strip galvanised,
20 x 1.5 mm
6041
6042
6043
6044
6045
6046
6048
6050
12.5
25
37.5
50
75
100
125
150
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
1.4
2.7
3.9
5.1
7.4
9.7
11.8
14.8
100
100
100
100
100
100
100
100
Suspension wire Ø 4
galvanised, with hook
6051
6052
6053
6054
6055
6056
12.5
25
37.5
50
75
100
4.0
4.0
4.0
4.0
4.0
4.0
1.4
2.7
3.9
5.1
7.4
9.7
100
100
100
100
100
100
Ø 6
also
available
in fixed
lengths
6020
6021
6022
6023
6024
6025
6026
6027
6028
6029
6019
13.5
20
30
40
50
60
70
80
90
100
170
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
2.5
3.5
5.6
7.5
9.0
10.5
12.6
15.0
16.5
17.5
31.0
100
100
100
100
100
100
100
100
100
100
50
Nonius hanger galvanised,
for T-rail/clamping profiles
6011 19 1.2 5.0 100
Ø 7
also
available
in fixed
lengths
6001 5000 1.5 17 coil
à
50
m
Sliding hanger galvanised,
for slotted strip
6060 12.5 1.5 2.2 100
suitable for T-mounting
rail with double bulb
Tension spring galvanised
6008
6009
20
10
–
–
2.5
1.8
100
100
with 250 mm wire hook
with 125 mm wire hook
close hook after fixing
max. f.
0.15 kN
adm. f. 0.25 kN
Connector galvanised,
for clamping profile ref. 5110
6080 10 0.6 2.0 100
adm. f.
0.40 kN
Flat head screw galvanised,
with special square collar
6204 1.6 5 0.4 100
Adjusting clamp
for nonius hanger system
6199 – – 0.6 100
with nut, SW 8,
M 5 x 16 mm
for slotted metal hanger
Clamping profile galvanised,
for metal cassettes
5110 400 0.6 49 10
Cross connector galvanised,
for clamping profiles
6085 – 0.6 1.4 100
Angle profile galvanised, coated
5334
5328
5332
300
300
300
0.5
0.5
0.5
19.6
17.0
25.5
40
40
40
24 x 24 mm, white
19 x 19 mm, white
30 x 30 mm, white
adm. f. 0.40 kN
Corner
connectors
for angle profile
ref. 5334
see page 4
40
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

approved to DIN 18168/2
Galvanized metal subconstructions
for clamping metal cassettes
K 500
1
2
3
4
5
6
7
8
9
10
11
Clamping profile ref. 5110
Tension spring with wire hook
ref. 6008/6009
Suspension wire with eye
ref. 6041–6050
Clamping profile connector ref. 6080
Wall angle ref. 5334
Metal cassette
Adjustable suspension strip ref. 6011
Adjusting strip ref. 6020–6029
Sliding hanger ref. 6060
Slotted metal strip ref. 6001
Insulating board
Detail:
Cross connection
with cross connector
ref. 6085
Detail:
Clamping
procedure
close hook!
Description and methods of suspension:
The metal cassettes are clamped into the
illustrated clamping profile ref. 5110 from below.
The individual ceiling cassettes can then be
opened at anytime, e.g. for revision purposes. Wall
connections are to be made with wall angles ref.
5334, which are placed on the cassettes. If the
clamping profile must be connected, then
clamping profile connector ref. 6080 must be used.
There are three possible methods of suspenslon:
1. Tension spring with wire hook ref. 6008 or 6009
for suspension wire with eye ref. 6041–6050
(125–1500 mm long).
Close hook with tongs after fixing.
2. Sliding hanger ref. 6060 for suspension with
adjustable suspension strips 20 x 1.5 mm
ref. 6001. Sliding hanger is to be attached to the
adjustable suspension strip with 2 adjusting bolts
M 5 x 15 mm ref. 6204.
3. Adjustable nonius hanger ref. 6011 and
adjusting strip ref. 6020–6029 (150–1000 mm
long). The nonius hanger and the adjusting strip
are fixed together by inserting two adjusting
clamps when both parts have been set in the
required position. In this way, the suspension
system can be adjusted to the millimetre and
has sufficient rigidity.
Hangers and profile joints have to be staggered.
An additional hanger has generally to be used on
the profile joints.
Appr. material requirements for 1 sqm ceiling
without waste material:
metal cassette 62.5 x 62.5 cm
distance between clamping profiles 62.5 cm
distance between hangers max. 1250 mm
1.50 m clamping profile ref. 5110
0.40 m angle profile
0.30 pcs clamping profile connector
ref. 6080
1.65 pcs tension spring with wire hook
ref. 6008 or 6009
1.65 pcs suspension wire with eyes/hooks
(alternatively sliding hanger ref. 6066
with slotted metal strip ref. 6001 and
2 adjusting bolts M5 x 15 mm ref. 6204
or Nonius hanger ref. 6011 and
adjusting strip)
These quantities are based on a ceiling area of
10 x 10 m. As the material requirements depend on
the size of the ceiling and the local conditions,
calculations of the exact quantities should take
these into consideration.
Tender Specification:
.......... m 2 suspended ceiling made from metal
cassettes.
Brand ...................... proportion of area with holes
................. color ........................ on metal subconstruction
as per Protektorwerk Structure 500.
The suspension height as per the construction plans
amounts to ........... cm. Suspension takes place
using tension spring with wire hook ref. 6008 or 6009,
suspension wire with eye/hook or
a) Sliding hanger ref. 6060 with slotted metal strip
ref. 6001 and 2 adjusting bolts M 5 x 15 mm
ref. 6204
b) Nonius hanger ref. 6011 and adjusting strip
Through this suspension, clamping profile ref. 5110
is supported. The rail joints as well as the hanger
must offset and an additional hanger must be
placed next to each joint for rigidity.
The metal cassettes will subsequently be clipped
into clip rails whose interval is determined by the
cassette format.
.............. m angle profiles for wall connections are
to be delivered and installed.
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 41

System 600
Profiles and accessories approved to DIN 18168/2
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Suspension wire Ø 4 mm
galvanised, with eye Ø 6
6041
6042
6043
6044
6045
6046
6048
6050
12.5
25
37.5
50
75
100
125
150
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
1.4
2.7
3.9
5.1
7.4
9.7
11.8
14.8
100
100
100
100
100
100
100
100
Suspension wire Ø 4 mm
galvanised, with hook
6051
6052
6053
6054
6055
6056
12.5
25
37.5
50
75
100
4.0
4.0
4.0
4.0
4.0
4.0
1.4
2.7
3.9
5.1
7.4
9.7
100
100
100
100
100
100
Hanger galvanised,
with tension spring
Ø 6
also
available
in fixed
lengths
Adjusting strip galvanised,
for nonius hanger
6020
6021
6022
6023
6024
6025
6026
6027
6028
6029
6019
13.5
20
30
40
50
60
70
80
90
100
170
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
2.5
3.5
5.6
7.5
9.0
10.5
12.6
15.0
16.5
17.5
31.0
100
100
100
100
100
100
100
100
100
100
50
6011 19 1.2 5.0 100
Ø 7
also
available
in fixed
lengths
Slotted metal strip galvanised,
20 x 1.5 mm, width of slots 6.5 mm
6001 5000 1.5 17 coil
à
50
m
Sliding hanger galvanised,
for slotted strip
Nonius hanger galvanised,
for T-rail/clamping profile
6060 12.5 1.5 2.2 100
suitable for T-mounting
rail with double bulb
6033 10 1.5 3.3 100
with tension spring
for T-rail
max. f. 0.15 kN
Adjusting clamp galvanised,
for nonius hanger system
adm. f.
0.40 kN
6199 – – 0.6 100
max. f. 0.25 kN
Pivot clip for timber panels, black
Flat head screw galvanised,
with special square collar
T-rail galvanised,
with flat indent
5004 400 0.5 36.3 15
6131
6133
6135
6137
6139
6134
6132
–
–
–
–
–
–
–
–
–
–
–
–
–
–
1.0
1.3
1.3
1.3
1.4
1.0
1.0
500
500
500
500
500
250
250
joint groove depths
10 mm 5 mm
15 mm 5 mm
15 mm 7 mm
20 mm 5 mm
20 mm 7 mm
10 mm 4 mm galv.
10 mm 5 mm galv.
6204 1.6 5 0.4 100
with nut, SW 8,
M 5 x 16 mm,
for slotted metal hanger
Hat profile galvanised, 13 x 26 mm,
with long hole 20 x 5.2 mm
Connecting pin galvanised,
for all T-rails with edge
6076 – – 0.7 100
Pivot clip for groove-and-tongue
timber panels galvanised
6146
6144
6148
–
–
–
–
–
–
0.6
0.6
0.6
250
250
250
groove depths 3 mm
groove depths 4 mm
groove depths 5 mm
5143 300 0.6 23.1 15
42
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

approved to DIN 18168/2
Galvanised metal suspension system for
timber panels or groove-and-tongue panels
(alternative direct fixing)
K 600
4
6
10
9
1
2
3
4
5
6
7
8
9
10
11
T-rail ref. 5004
Timber panel pivot clips
ref. 6131/6139
Hanger with tension spring
ref. 6033
Suspension wire with eye
ref. 6041–6050
Adjustable nonius hanger ref. 6011
Adjusting strip ref. 6020–6029
Connecting pin ref. 6076
Timber panels
Sliding hanger for slotted strip
ref. 6060
Slotted suspension strip ref. 6001
Hat profile ref. 5143
3
1
2
5
8
7
Description and methods of suspension:
The wooden panels or groove-and-tongue boards
are installed by fastening the appropriate pivot
clips to the T-rails. ref. 5004. The clips should be
secured by riveting (with riveting tongs ref. 6513) or
screwing them to the T-rails. The tongues on the
clips are inserted into the grooves in the boards. A
variety of clips are available for different groove
sizes and joint spacing.
The two-piece panel tension locks are intended for
use in ceiling systems where any required part can
be disassembled if necessary.
There are three possible methods of suspension:
1. Hanger with tension spring, ref. 6033 and
suspension wire with eye ref. 6041–6050
(125–1500 mm long).
2. Sliding strip ref. 6060 in combination with slotted
strip 20 x 1.5 mm, ref. 6001. The sliding strip is
fixed to the slotted suspension strip by means of
2 adjusting bolts M 5 x 16 mm, ref. 6204.
3. Nonius hanger ref. 6011 and adjusting strip
ref. 6020–6029 (150–1000 mm long). The
adjustable suspension strip and the adjusting
strip are fixed together by inserting two clamps
when the strips have been set in the required
position. In this way, the suspension system can
be adjusted to the millimetre and has sufficient
rigidity.
Rail joints should be reinforced by two connecting
pins, ref. 6076. The suspension strips and rail joints
should be set in a staggered arrangement. An
additional suspension strip should be installed at
the joints.
Approx. material requirements for 1 sqm
suspension system without waste material:
Distance between T-rails: 600 mm
Distance between suspension strips: 1000 mm
1.7 m T-rail ref. 5004
16.0 pcs Timber panel pivot clips
ref. 6131–6139 or 6146–6148
0.7 pcs Connecting pins, ref. 6076
2.1 pcs Hanger with tension spring, ref. 6033
2.1 pcs Suspension wire with eye/hook
(alternatively: sliding strip ref. 6060
with slotted strip ref. 6001 and
2 adjusting bolts M 5 x 16 mm,
ref. 6204 or nonius hanger ref. 6011
and adjusting strip
These quantities are based on a ceiling area of
10 x 10 m. As the material requirements depend on
a size of the ceiling and the local conditions,
calculations of the exact quantities should take
these into consideration.
Tender Specification:
......... m 2 suspended sub-ceiling for groove and
tongue timber panels.
Brand ...................... groove strength ................. joint
interval........................... on metal subconstruction
as per Protektorwerk Structure 600.
The suspension height as per the construction plans
amounts to ........... cm. Suspension takes place
using a hanger with tension spring ref. 6033,
suspension wire with eye/hook or
a) Sliding hanger ref. 6060 with slotted metal strip
ref. 6001 and 2 adjusting bolts M 5 x 15 mm
ref. 6204
b) Nonius hanger ref. 6011 and adjusting strip
The T-rail ref. 5004 is suspended by this hanging. The
rail joints as well as the hanger must offset and an
additional hanger must be placed next to each
joint for rigidity.
The panels are affixed using timber panel pivot
clips ref. 6131–6139 diagonal to the T-rails.
Alternative: Direct fixing hat profile ref. 5143 (K 1400)
Timber groove-and-tongue panel Timber panel groove –
Also see page 86 wall covering
groove with timber spring
Timber panel with
timber spring
groove depths 4/5 or 7 mm
groove
groove depths 3, 4 or 5 mm
groove depths 4/5 or 7 mm
Joint 10/15 or 20 mm
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 43

System 900
Profiles and accessories approved to DIN 18168/2
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Adjusting strip galvanised,
for nonius hanger
Support rail galvanised, black
for expanded metal lath
6020
6021
6022
6023
6024
6025
6026
6027
6028
6029
6019
13.5
20
30
40
50
60
70
80
90
100
170
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
2.5
3.5
5.6
7.5
9.0
10.5
12.6
15.0
16.5
17.5
31.0
100
100
100
100
100
100
100
100
100
100
50
Ø 7
also
available
in fixed
lengths
5016 400 0.7 38.0 10
Nonius hanger galv., for support rail
ref. 5016 with perforation Ø 6.5 mm
Flat head screw galvanised,
with special square collar
6017 17 1.2 5.0 100
6204 1.6 5 0.4 100
with nut, SW 8,
M 5 x 16 mm
adm. f. 0.25 kN
Adjusting clamp galvanised,
for nonius hanger system
6199 – – 0.6 100
Connecting piece galvanised,
black coated for rail ref. 5016
6084 9 0.6 2.6 50
Adjusting bracket galvanised, for the
connection of adj. strip and extension strip
6201 – – 0.5 100
per connection
1 piece
Adjusting brackets
must be bent after
installation.
44
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

approved to DIN 18168/2
Galvanised metal suspension system for
expanded metal lath as plaster base
K 900
1
2
3
4
5
6
7
Support rail ref. 5016
Connector ref. 6084
Flat hat screw ref. 6204
Nonius hanger ref. 6017
Adjusting strip ref. 6020–6029
Adjusting clamp ref. 6199
Expanded metal rib lath
Description and methods of suspension:
The fixing is effected with the support rail ref. 5016.
It is supplied with punched-out tongues, which are
bent back at right angles. The expanded metal ribs
are pushed against these tongues, which are bent
around the ribs to secure the metal lath.
Rail joints are conducted with connector ref. 6084.
This will be clipped to both end rail pieces and
additional anchored with two flat head screws
ref. 6204 with the connected support rails.
Suspension takes place with the Nonius hanger
ref. 6017, which is connected to the rail support
with a flat head screw ref. 6204.
The roof attachment takes place with correspondingly
long adjusting strips ref. 6020–6029
(150–1000 mm long). Nonius hanger and adjusting
strips must be connected by two adjusting clamps
ref. 6199 placed together. Pegs and/or clamps
which are not self-securing must be bent. The
minium suspension height amounts to 180 mm.
Hangers and/or rail joints must be offset. An
additional hanger is generally installed at the rail
joint.
Please note the positioning guidelines of DIN 4121,
DIN 18550 and the plaster support manufacturer.
Approx. material requirements for 1 sqm ceiling
system without waste of materials:
Distance between support rails: 600 mm
Distance between hangers: 600 mm
1.7 m Support rail ref. 5016
3.00 Stück Hangers ref. 6017
3.00 Stück Adjusting strips
6.00 Stück Adjusting clamps ref. 6199
0.40 Stück Connector ref. 6084
3.80 Stück Flat head screws ref. 6204
These quantities are based on a ceiling area of
10 x 10 m. As the material requirements depend on
the size of the ceiling and the local conditions, calculations
of the exact quantities should take these
into consideration.
Tender Specification:
......... m 2 suspended plaster sub-ceiling on metal
subconstruction as per Protektorwerk Structure 900
in conjunction with expanded metal lath hole rib or
combination rib.
The suspension height amounts to ........... cm.
Suspension takes place with Nonius hanger
ref. 6017 and adjusting strip. The rail joints must be
offset.
The expanded metal ribs are pushed onto the
latches of the rails from below and attached by
bending the latches around the support ribs on the
rails. In doing so, care must be taken that no
latches are skipped and that the latches are bent
fully around the ribs.
The expanded metal ribs should overlap on the
diagonal and lengthwise joints as per the
manufacturer’s guidelines. The diagonal joints
must also be offset.
Arch profile ref. 5072
Support rail ref. 5016
Nonius hanger ref. 6017
Flat head screw ref. 6204
Plaster stop bead. e. g. ref. 1214
Expanded metal rib lath
Fixing example:
Vaulted expanded metal rib lath construction
with the use of system components of the
construction “K 400 arch”
Please refer to the page nos. 26–27
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 45

System 1100
Profiles and accessories approved to DIN 18168/2
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Suspension wire Ø 4 mm
galvanised, with eye Ø 6
6041
6042
6043
6044
6045
6046
6048
6050
Main T-rail galvanised,
white coated for exposed grid
5335
5340
12.5
25
37.5
50
75
100
125
150
375
360
4.0
4.0
4.0
4.0
4.0
4.0
4.0
0.41
0.41
1.4
2.7
3.9
5.1
7.4
9.7
11.8
14.8
37.0
37.0
100
100
100
100
100
100
100
100
Suspension wire Ø 4 mm
galvanised, with hook
6051
6052
6053
6054
6055
6056
12.5
25
37.5
50
75
100
4.0
4.0
4.0
4.0
4.0
4.0
1.4
2.7
3.9
5.1
7.4
9.7
100
100
100
100
100
100
Hanger galvanised, with special
tension spring for main-T-profiles
6162 11 1.5 3.4 100
25
25
Ø 6
also
available
in fixed
lengths
adm. f.
0.15 kN
with fire protection
for grid 625
for grid 600
Profiles 15 x 38 mm
see page 12
other
colours
on
request
Corner connector for wall angle
ref. 5334, galvanized, painted white
6114 - 0.40 1.0 100
Slotted metal strip galvanised,
20 x 1,5 mm, width of slots 6,5 mm
6001 5000 1.5 17 coil
à
50
m
Sliding hanger galvanised, for slotted
metal strip, suitable for main-T-rails
6065 12.5 1.5 1.9 100
Flat head screw galvanised,
with special square collar
6204 1.6 5 0.4 100
6112 12 1.2 4.2 100
with nut, SW 8,
M 5 x 16 mm,
for slotted metal hanger
Short suspender 40 mm adjustable
for K 1100 including adjusting strip
Ø 6.5 x 8
for interior
corners
max. f. 0.15 kN
Angle profile galvanised, coated
5334
5328
5332
300
300
300
0.5
0.5
0.5
19.6
17.0
25.5
40
40
40
24 x 24 mm, white
19 x 19 mm, white
30 x 30 mm, white
Corner
connectors
for ref. 5334
see page. 4
Angle profile galvanised,
for shadow joints, white coated
5329 300 0.5 25.0 40
PVC wall angle white
concave/convex bendable
3769 250 1.50 13.9 10
Nonius hanger galvanized
for K 1100
6016 19 1.2 5.0 100
See page 44
on the upper left
for adjusting strips
Board clamp galvanised,
for 16 mm acoustic tiles
6153 – – 0.35 500
max. f. 0.15 kN
Cross T-rail galvanised,
white coated for exposed grid
5336
5341
5337
5342
125
120
62.5
60
0.41
0.41
0.41
0.41
46.2
44.4
23.1
23.2
50
50
75
75
Corner connector for wall angle
ref. 5334, galvanized, painted white
6113 - 0.40 1.0 100
with fire protection
for grid 625
for grid 600
for grid 625
for grid 600
Profiles 15 x 38 mm
see page 12
other
colours
on
request
for exterior
corners
Assembly methods:
max. f. 0.15 kN
Wall spring
for fixing end boards
6099 – – 0.7 250
Adjusting clamp galvanized,
for Nonius suspension systems
6199 – – 0.6 100
1 = Main T-rail
2 = Cross T-rail
3 = Cross T-rail
4 = Hanger
5 = Distance between main profiles, centre
to centre 1200–1250 mm
6 = Distance between main profiles, centre to
centre 600–625 mm
7 = Main profile span (from hanger to hanger) max. 1.50 m,
but smaller around lightning equipment, with a distance
of 600–625 mm between the main profiles (see assembly
methods) and a board weight of approx. 7.5 kg/sqm.
8 = Main profile span (from hanger to hanger) max. 1.25 m, but
smaller around lightning equipment, with a distance of 1200–
1250 mm between the main profiles, centre to centre (see assembly
methods) and a board weight of approx. 7.5 kg/sqm.
46
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

approved to DIN 18168/2
Galvanised metal suspension system white coated,
for ceiling boards in exposed grid system
Fire tested
K1100
1
2
3
4
5
6
7
8
9
9A
10
Main T-rail
Cross T-rail in required lenghts
Hanger with tension spring
ref. 6162
Suspension wire with eye
ref. 6041–6050
Sliding strip for slotted strip
ref. 6065
Slotted strip ref. 6001
Board clip ref. 6153
Wall spring ref. 6099
Wall angle
PVC-angle profile, white,
flexible, concave/convex ref. 3769
Ceiling board
alternative:
Expanded metal ceiling tiles
see page 15
(Please ask for our special brochure
number 13025 free of charge)
Approx. material requirements for 100 sqm suspension system without waste material. Complete ceiling weight 7.5 kg/sqm.
Grid size Assembly Main rail m Cross rail cm m/piece Wall angle Wall spring Suspension strips Board clips
mm method ref. ref. m ref. 6099 and wires Nr. 6153
pcs pcs pcs
600 x 600 A 5340 83 5341 120 166/138 40 60 85 240
5342 60 83/138
625 x 625 A 5335 80 5336 125 160/128 40 60 80 230
5337 62,5 80/128
600 x 600 B 5340 166 5342 60 166/276 40 60 170 240
625 x 625 B 5335 160 5337 62,5 160/256 40 60 160 230
600 x 1200 C 5340 83 5341 120 166/138 40 60 85 150
625 x 1250 C 5335 80 5336 125 160/128 40 60 80 140
600 x 1200 D 5340 166 5342 60 83/138 40 60 170 150
625 x 1250 D 5335 160 5337 62,5 80/128 40 60 160 140
Assembly method and material requirements for board weights over 7.5 kg/sqm on request.
Fire rating tested with mineral fibre boards 15 mm Type AMF. Test reports of F 90 acc. DIN 4102 for grid size 62.5 x 62.5 and 125 x 62.5 of MPA Braunschweig
are available. The test has been made on raw ceilings of construction type II and III acc. DIN 4102 with main and cross T-rails in dimension of 24 x 38 mm.
Description and methods of suspension:
The boards are suspended using main T-rails in fixed
lengths of 3.60 or 3.75 m and cross T-rails in lengths
according to the size of the boards. The main and
cross rails are fitted into each other without any
additional fixing materials.
An advantage of this visible lay-in system is that the
ceiling boards can be removed at any required
point. Care should be taken, however, that the
ceiling boards are approx. 5 mm smaller than the
grid size.
E. g.:
Grid size 625 x 625 mm = Board size 620 x 620 mm.
The ceiling boards on the edges are to be cut in
such a manner that board clip ref. 6153 can be
inserted between the edge angle and the ceiling
board.
There are two possible methods of suspension:
1. Hanger with tension spring, ref. 6162, and
suspension wire with eye, ref. 6041–6050
(125–1500 mm long).
2. Sliding strip for slotted strip ref. 6065 for
suspension with slotted strips 20 x 1.5 mm
ref. 6001. The sliding strip is affixed to the slotted
strip with 2 flat head screws M 5 x 15 mm
ref. 6204.
The hangers and rail joints should be installed in a
staggered arrangement. An additional hanger
should be installed at the rail joints.
Tender Specification:
......... m 2 suspended sub-ceiling as inlay installation
with visible white stove-enamel profiles and the
following boards:
Brand ...................... surface .....................
format ......................... with metal subconstruction
as per Protektorwerk Structure 1100.
Installation form: A, B, C, D (cross out those which
do not apply).
The suspension height as per the construction plans
amounts to ........... cm. Suspension takes place
using hanger with tension spring ref. 6162,
suspension wire with eye/hooks or sliding strip
ref. 6065 with slotted strip ref. 6001 and 2 flat head
screws M 5 x 15 mm ref. 6204.
The T-rails are supported with these suspension
whose intervals are determined from the board
format. The rail joints as well as the hanger must
offset and an additional hanger must be placed
next to each joint for rigidity. Slotted recesses are
located in the grid of the beams of the T-rails,
through which the cross T-rails are inserted and will
then click into place. The boards are loosely
inserted after adjusting the grid construction so
that they can be removed afterwards at any time.
............ m wall connection with wall angle ref. 5334
white stove-enamel to be delivered and installed.
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 47

SUBCONSTRUCTIONS
FOR METAL STUD WALLS

Profiles and accessories for
light partitions and wall linings
Corrosion protected
C- and U-profiles
upon request
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Felt strip self-adhesive one side
6180
6187
6181
6188
6189
2000
2000
2000
2000
2000
3.0
3.0
3.0
3.0
3.0
1.9
2.2
2.8
3.5
4.5
coil
20 m
Felt strip self-adhesive both sides
6175 1000
6176 1000
5.0
5.0
6.5
7.5
coil
10 m
“A”
60 mm wide
80 mm wide
Foam tape polyurethane,
self-adhesive one side
6197
6194
6195
6196
3000
3000
3000
3000
3.0
3.0
3.0
3.0
0.8
1.1
1.6
2.0
coil
30 m
“A”
40 mm wide
50 mm wide
60 mm wide
70 mm wide
95 mm wide
“A”
30 mm wide
45 mm wide
70 mm wide
95 mm wide
Fixing element galvanised,
striker screw with synthetic dowel
6248 4.0 6 0.4 100 to fix runners,
drill diametre 6 mm,
max. fastening
thickness = 12 mm
not to be used for
suspended ceilings
6 x 40 mm
U-wall profiles – UW –
as per DIN 18182/1, galvanized
5275
5276
5230
5232
5233
5234
5248
5247
5236
5237
5238
350
250
260
400
250
260
400
260
400
260
400
400
400
400
400
400
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.60
0.70
0.70
0.70
49.2
51.9
58.0
62.0
69.0
80.6
88.0
98.0
91.8
105.5
119.2
12
8
8
U-wall profiles – UW –
as per DIN 18182/1, galvanized
5277
5278
5279
5261
5262
5263
400
400
400
130
130
130
0.60
0.60
0.60
0.60
0.60
0.60
58.0
69.0
92.5
80
100
110
per
100
pieces
8
8
8
8
4
4
4
4
8
8
8units
“A”
40 x 35 x 40 mm
40 x 40 x 40 mm
40 x 50 x 40 mm
40 x 60 x 40 mm
40 x 75 x 40 mm
40 x 100 x 40 mm
40 x 125 x 40 mm
40 x 150 x 40 mm
60 x 50 x 60 mm
60 x 75 x 60 mm
60 x 100 x 60 mm
prepunched for curved
partitions
40 x 50 x 40 mm
40 x 75 x 40 mm
40 x 100 x 40 mm
Ledge profile, pre-punched to DIN
raw construction opening dimensions
See also
page 93
UW 50–06
UW 75–06
UW 100–06
for sliding
ceiling
} connections
MAXI-CW-profiles
as per DIN 18182/1, galvanized
5269
5211
5214
5215
5216
5141
5224
5221
5218
5219
5206
5207
5208
260
250
260
275
300
325
350
400
450
500
300
250
260
275
300
325
350
400
450
500
600
260
275
300
325
350
400
450
500
600
Fixl.
order lengths
Fixl.
0.60
0.60
0.60
0.60
0.60
0.60
0.60
65.6
70.6
75.1
82.0
92.9
109
116.1
0.70 85.2
0.70 99.0
0.70 112.1
1.00 121.7
1.00 141.0
1.00 160.0
12
8
8
8
8
8
4
8
8
8
8
8
8
5206, 5207, 5208
not products on hand!
Order specific
manufacturing:
min. acceptance
1000 m per profile.
“A”
33.8 mm CW 35-06
48.8 mm CW 50-06
58.8 mm CW 60-06
73.8 mm CW 75-06
98.8 mm CW 100-06
123.8 mm CW 125-06
148.8 mm CW 150-06
48.8 mm CW 50-07
73.8 mm CW 75-07
98.8 mm CW 100-07
48.8 mm CW 50-10*
73.8 mm CW 75-10*
98.8 mm CW 100-10*
* No H-punching
available for these
profiles!
»H«-cutouts at the beginning and the end of the stud.
Lengths indicated are on stock, order lengths on
demand.
From 6 m bar length, ask about fixed length surcharge!
50
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Profiles and accessories for
light partitions and wall linings
MAXI-S-CW-Profiles
galvanised
5615
260
275
300
350
400
0.60
95.0
+ order lengths
4
for improved sound
absorption values of
light weight partitions
incl. cable protective
sleeves ref. 6411
(4 pcs. per length)
that are added
“A”
73.8 mm
Reinforcing channel for door frames
galvanised, acc. DIN 18182/1
Fixing set, galvanised
6203 2.0 8.0 2.1 100 consisting of flat head
screws with special
square collar DIN 603/4.6
with washer and nut
M 8 x 20 galv. SW 13
For fixing door frame
with reinforcing channel.
5616
260
275
300
350
400
0.60 108
+ order lengths
4
49
98.8 mm
Fixing angle for reinforcing channel
ref. 5129 + 5135, galvanised
6185 – 2.0 9.2 25
Inside corner profile 90°, galvanised
acc. DIN 18182/1
5170 250
300
350
400
0.60 65 10
47
A
Flexible U profile, galvanised,
in sectional form
5601 300 0.80 108 10
30 x 75 x 30 mm
for round partitions,
round pillars, arched
suspended ceilings
in connection with
CW studs 75-06 ref. 5215
Plug in angle set for door posts for
CW studs or UA profiles with dowel
6751
6752
6753
2.0
2.0
2.0
74
108
144
1 S.
1 S.
1 S.
30
75
Set consists of:
4 plug in angles
8 pegs 8 x 60
8 PVC guide rails for
CW-profiles
“A”
for UA/CW 50 47 mm
for UA/CW 75 73 mm
for UA/CW 100 97 mm
“A”
Reinforcing channel for door frames
galvanised, acc. DIN 18182/1
100
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
5129
5135
260
300
350
400
450
500
300
400
2.0
2.0
177
177
4
4
“A”
40 x 48.8 x 40 mm
UA 50–20
35 x 58.8 x 35 mm
UA 60–20
Ø 8
5130
5131
5132
260
300
350
400
450
500
550
600
400
}
2.0
2.0
2.0
199
248.5
287.0
+ order lengths
4
4
4
“A”
73.8 mm UA 75 –20
98.8 mm UA 100 –20
123.8 mm UA 125 –20
Fixing angle for reinforcing channel,
galvanised
6183
6182
–
–
2.0
2.0
16.9
23.4
25
25
for ref. 5130 UA 75–20
for ref. 5131 UA 100–20
Inside corner profile, galvanised
5440
5442
5444
300
300
250
300
350
400
0.60
0.60
0.60
65
65
65
10
10
10
angle 105°
angle 120°
angle 135°
Other angles on
request.
Outer corner profile, galvanised
5441
5443
5445
300
300
250
300
350
400
0.60
0.60
0.60
65
65
65
10
10
10
angle 105°
angle 120°
angle 135°
Other angles on
request.
See also
page 93
‹
‹
125
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 51

Profiles and accessories for
light partitions and wall linings
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Heavy corner profile, galvanised,
for partitions with jointing perforation
U-connection profile, galvanized
for CD-facing plywood
Adjustment bracket, galvanized,
for facing plywood with UW-profile
5192 400 1.5 141
units
angle 90°
5244 300 0.60 38.0 16
27 x 28.5 x 27 mm
6149
6155
6150
6151
6
3
9
4.5
1.0
0.80
1.0
0.8
5.2
3.4
6.0
3.9
100
100
100
100
60 x 50 x 32 mm
30 x 50 x 32 mm
for UW 50–06
32
ø 20 x 6,3
5193 400 1.5 141
units
angle 135°
U-connection profile, galvanized
for CD-facing plywood
further dimensions
on request
5168 300 0.60 46.9 16
Furring channel, galvanised
for screwing on plasterboards
5112 230
400
0.60 41.4 10
See also
page 91
Angle profile, for recessed skirting,
galvanised
CD 60-06 as per DIN 18182/1,
for facing plywood
Do not use as hat
ceiling profile instead
of ref. 5114!
5173
5174
250
250
0.70
0.70
110
88
10
10
200 x 12 mm
150 x 12 mm
5120 400
310
260
0.60 57.0 12
Trimming channel, galvanised,
for solid gypsum blocks
5133
5134
5136
400
400
400
0.60
0.60
0.60
59.3
71.3
80.0
8
8
8
“A”
32 x 61.5 x 32 mm
35 x 81.5 x 35 mm
35 x 101.5 x 35 mm
Adjustment bracket, galvanized,
for facing plywood with CD-profile
Hat profile, galvanised
6156
6158
3
6
0.80
0.80
3.4
4.3
100
100
ø 20 x 6,3
5143 300 0.60 23.1 15 for joint covers, glazing,
cladding, skirting
6154 9 0.80 6.3 100
52
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Profiles and accessories for
light partitions and wall linings
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Hat profile, galvanised,
for glazing
5156 300 0.60 28.5 15
PVC covering strip, white(10),
grey (22), black (90), brown (47)
3762 300 1.5 11.1 15
in combination with hat
profile ref. 5143
Skirting profiles aluminium
with fixing clipses
6545
6410
400
5
1.5
-
35
1.3
10
-
Alu anodised, E6 EV 1
2.5 clipses included per
lm = 10 pcs./length
Aluminium covering strip,
anodised, E6 EV 1
Glazing profile, plastic APTK,
black, for 4 mm glass
6578 300 2.0 24.0 10
in combination with hat
profile ref. 5143
6555 5000 4.0 13.3 coil
à
50 m
for head profile ref. 5143
PVC-ceiling guide for glazing
with sealing lips
Glazing profile, plastic APTK,
black, for 4 - 6 mm glass
3765 300 2.0 21.1 15
in combination with
hat profile ref. 5166
white (10), grey (22),
black (90), brown (47)
12 x 56 mm
6554 2500 – 12.4 coil
à
25 m
for hat profile ref. 5156
Filling profile, for hat profiles
ref. 5143 and ref. 5156
5139 300 0.50 12.0 50 galvanised , 9 x 11.5
Nr. 6410
powder coated,
colour RAL on demand
Aluminium channel white coated,
perforated for glazing
6551
6552
6553
250
250
250
0.8
0.8
0.8
26.0
31.0
36.0
8
8
8
“A”
29 x 77 x 29 mm
29 x 102 x 29 mm
29 x 127 x 29 mm
3651 350 1.5 10.0 20 PVC 12.5 x 10 mm
white (10)
Aluminium hat profile
anodised, E6 EV 1
6549 300
350
1.5 20.0 20
Perforation part 16 %
PVC skirting profile in combination
with hat profile ref. 5143
PVC filling profile for ref. 6549
3703 300 1.5 23.3 15 white (10), grey (22),
black (90)
3655 300
350
1.4 5.0 20 PVC, in colour white (10)
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 53

Profiles and accessories for
light partitions and wall linings
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Angle profile, galvanised,
for F-90 fire resistant partition
5182 300 2.0 130 4
RC-channel, galvanised
5100 400 0.60 35.5 10 for the improvement of the
sound insulation of walls.
To be fixed horizontally
Ø 4,5
13,5
Angle profile, galvanised,
for F-90 fire resistant partition
14
60°
5,5
40
e = 100 mm
5183 300 1.0 85 4
Fixing channel for heavy fixtures
to the face of partition
6670 62.5 0.70 1.2
pcs
unit
625 x 300 mm
U-profile, galvanised,
for F-90 fire resistant partition
5184 300 2.0 195 4
Installation of the
heavy fixtures with
timber screws
ref. 6212/6213 without
pilot drilling and
without cavity dowel.
See also
page 105
L-connecting profile
5501 300 4.0 470
unit
54
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Accessories for
light partitions and wall linings
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Self tapping screws type TN
acc. DIN 18182/2
Wood screw with posi-drive slot,
grade 2, galvanized
Sheet screw with flat head
6205
6206
6208
6209
2.5
3.5
4.5
5.7
3.5
3.5
3.5
3.8
0.16
0.20
0.27
0.34
1000
1000
1000
500
trumpet head
double shank
special phosphated,
point for material
thickness
up to 0.70 mm
3.5 x 25 mm
3.5 x 35 mm
3.5 x 45 mm
3.8 x 57 mm
6212
6213
4.5
7.0
5
5
0.48
0.72
250
250
coated, for suspension
at timber construction
elements, for ex. wire
with eye or heavy
fixtures at fixing
channel ref. 6670
5.0 x 45 mm
5.0 x 70 mm
6236
6237
6238
1.3
1.9
4.1
4.2
4.2
4.2
0.18
0.25
0.27
1000
1000
1000
and Philip’s head,
galvanized, self drilling
point for sheet
thickness from 0.70 to
2.25 mm head exterior
diameter 11 mm
4.2 x 13 mm
4.2 x 19 mm
4.2 x 41 mm
Self drilling screws type TB
acc. DIN 18182/2
6211
6219
7.0
9.0
4.2
4.2
0.56
0.86
500
500
4.2 x 70 mm
thread length 45 mm
4.2 x 90 mm
thread length 64 mm
6215
6216
6217
2.5
3.5
4.5
3.5
3.5
3.5
0.16
0.20
0.27
1000
1000
1000
trumpet head, sheet
steel thread, special
phosphated, self
drilling point for
material thickness from
0.70 up to 2.25 mm
3.5 x 25 mm
3.5 x 35 mm
3.5 x 45 mm
Super TEKS screw galvanised
6234 1.9 6.3 0.67 500 6.3 x 19 mm, SW 10
self-drilling point for
material thickness
up to 6.0 mm
Self tapping screws type TN
with coarse thread
6222
6223
6224
6225
3.5
4.5
5.7
7.5
3.8
3.8
3.8
4.2
0.22
0.29
0.34
0.60
1000
1000
500
500
All types with cross
head for Phillips bits
No. 2
trumpet head
special phosphated
3.8 x 35 mm
3.8 x 45 mm
3.8 x 57 mm
4.2 x 75 mm
All types with cross
head for Phillips bits
No. 2
Fiber board screw, phosphated,
with Philip’s head and flat head
6241 3.0 3.9 0.18 1000 3.9 x 30 mm
Steel framing screw
with crossed pan head
6239 1.3 4.2 0.16 1000
6240 1.3 4.2 0.13 1000
Drywall screw FN
with flat head
6242 3.8 - 0.39 200
All types with cross
head for Phillips bits
No. 2
galvanised
self drilling point for
material thickness
up to 0.70 mm
4.2 x 13 mm
4.2 x 13 mm
with cross head
4.2 x 35 mm
for TPS and other systems
Sheet metal screw with cross head
type LB as per DIN 18182/2
cross head, galvanised,
self-drilling point for
material thicknesses
up to 2.25 mm
Aluminium blind rivet 3 x 5 mm
6178 – 3.0 0.1 500
Cavity dowel plastic
with galvanised screw
6249
6250
6233
6.0
4.8
ø 10
ø 10
1.3
1.2
25
25
red for
2 x 12,5 mm boards
blue for
1 x 12,5 mm boards
Sheet screw with flat head,
galvanized
6.3 x 19 mm, TX 30
self-drilling point for
material thicknesses
up to 6.0 mm
6227
6218
1.1
2.5
3.8
4.2
0.09 1000
0.17 1000
3.8 x 11.1 mm
4.2 x 25 mm
Special holder with
bit upon request
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 55

ACCESSORY PROFILES
FOR DRYLINING

25
Corner profiles for smoothing
Drylining
Smoothing works
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Aluminium corner bead 15 x 21 mm
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Corner bead, galvanised
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Drywall corner tape with two
PVC-strips on Kraft paper
9077 250 0.4 0.5 50
15
21
1078 250
300
0.45 16.8 25
31 x 31 mm
3
31
3001 1 R.
=
30
m
0.45 3.0 1 box
=
5 rolls
Aluminium corner bead 25 x 25 mm
}
9078
9079
200
250
275
300
0.5
0.45
4.7
4.2
50
50
4
25
Aluminium corner bead 25 x 25 mm
9172 250
300
0.5 4.7 50
angle 135°
5,5
135°
25
Alu mini mesh corner bead
9178 250 0.5 6.0 25
Aluminium corner bead 25 x 25 mm
9278 250 – 5.1 50
4
Aluminum stop profile 13 x 23 mm
9299 250
300
0.4 3.2 50
»Göppinger Profile«
für 12.5 mm plasterboards
Alu stop profile for borders
jointed from one side
9002 250 – 5.1 50
Aluminium corner bead 45 x 45 mm
9179 250
300
0.5 10.0 25
with coating
Aluminum stop profile 11 x 25 mm
9298 250 0.4 3.1 50
»Göppinger Profile«
für 9.5 mm plasterboards
Corner bead, galvanised
1030 250
300
0.45 13.5 25
25 x 25 mm
3
3
45
25
PVC corner bead for spackling work
23 x 23 mm
3751 coil
à
50 m
– – 1 box
=
2 rolls
25
4
11
Corner beads made of aluminium or
galvanised steel for skimmed plasterboards.
Lengths of flanges suit different thicknesses
of plasterboards.
All corner beads have to be embedded
completely into joint filler and have to be
skimmed up to the nosing.
9172 Profile to form 135° edges.
9299 The »Göppinger Profile« made from
aluminium for borders jointed from one side
at the areas of sliding wall and ceiling
connections.
9298 Stop profile for borders jointed from
one side at the areas of sliding wall and
ceiling connections.
3751 PVC corner bead “on the roll”. The
flexible bend enables the application for
squint and obtuse corners.
3001 Seperated PVC strips, covered with
Kraft paper, as corner protection for squint
and obtuse edges.
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com
57

22
9,5
8,5
22
22
20
„th“ „d“
18
10
Drylining
Plasterboards 9.5–20 mm
Edge and Corner Profiles
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Edge profile galvanised
PVC edge profile, white
1120 250 0.56 15.5 25
for 9.5 mm
plasterboards
3741
3747
250
300
250
300
1.5
1.5
8.0
12.0
50
50
“th”
for 12.5 mm plasterboards
for 15 mm plasterboards
8,5
Edge profile galvanised
PVC edge profile, white
1121
1122
250
300
250
0.56
0.56
18.4
19.8
25
25
“th”
for 12.5 mm plasterboards
for 15 mm plasterboards
3502 250
300
1.5 17.0 10
for 20 mm plasterboards
42
20
Profile 1121
primary
coating
white
„th“ „d“
8,5
15
Edge profile galvanised
PVC corner edge profile, white
1123 250 0.56 20.3 25
for 18 mm plasterboards
3744 250
300
1.2 19.7 50
for 12.5 mm plasterboards
12,5
12,5
27
18
PVC edge profile, white
3738 250 1.5 6.5 50
for 9.5 mm plasterboards
20
10
9,5
Edge profiles made of galvanised
steel or PVC for different thicknesses of
plasterboards to provide exact edging
and connection.
Do not skim profiles - prime only!
Edge profiles from PVC for inserting
plasterboards of various thicknesses.
Only spackle the profile, do not over
spackle.
58
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

40
12,5
12,5
„A“
Plaster Stop, Shadow Joint Profile
Drylining
Plasterboards 9.5–25 mm
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Stop bead galvanised
Shadow joint profile galvanised
Shadow joint profile galvanised
1135
1131
1132
}
250
300
0.56
0.56
0.56
18.0
18.0
18.0
25
25
25
“A”
11.5 = 9.5 mm plasterboards
14 = 12.5 mm plasterboards
16.5 = 15 mm plasterboards
1313
1315
250
300
300
0.56
0.56
26.6
30.7
15
15
“A”
14 = 12.5 mm plasterboards
16.5 = 15 mm plasterboards
1371 250
300
0.56 21.8 15
for 12.5 mm plasterboards
28/30
„A“
2263
250
0.50
25.9
15
14 = 12.5 mm plasterboards
in stainless steel
53
20
Shadow joint profile, galvanised
9,5
bis
15
30
1311
300
0.56
33.0
15
for 12.5 mm plasterboards
2241
250
300
0.50
33.0
15
in stainless steel
for 12.5 mm plasterboards
12,5
bis
25
Stop bead galvanised
Shadow joint profile galvanised
1133
1134
1136
}
250
300
0.56
0.56
0.56
21.6
21.8
25.0
25
25
25
“A”
19.5 = 18 mm plasterboards
21.5 = 20 mm plasterboards
26.5 = 25 mm plasterboards
1319
1328
250
300
300
0.56
0.56
25.6
32.0
15
15
for 12.5 mm plasterboards
for 15 mm plasterboards
14
38/40
„A“
46
15
1750 300 0.45 26.1 25
18
bis
25
Stop profile galvanised
Shadow joint profile galvanised
1138 250 0.56 34.2 15
10
12,5
1314 250
300
0.56 23.7 15
for 12.5 mm plasterboards
1751 300 0.45 18.8 25
28
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 59

12
Drylining
Plasterboards 9.5–12.5 mm
Corner and Stop Beads,
Decorative Beads
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
PVC corner bead, white, 33 x 33 mm
3767 300 – 8.5 20
for curved corners
PVC reveal bead
3772 305 – 10.5 20
PVC corner bead, white,
for oblique 135° corner
12,5
3789 305 – 11.6 30 27
See also
page 92
3
33 33
22
21
4
PVC inner corner bead, white
PVC inner corner bead
3770 305 – 7.4 70
3780 305 – 14.0 35
22
r=23,5
32
PVC stop bead, precut
for curved boards, white
PVC corner bead
3776 305 – 12.4 35
PVC corner bead
3778 305 – 10.4 35
PVC rail
3774 305 – 14.1 20
21
27
r=17
3768 300 1.1 7.7 20
PVC stop bead
3766 300 – 17.0 35
See also
page 92
13,5
11,5
PVC stop bead with flexible lips
3784 300 – 6.5 30
for 9.5 or 12.5 mm
plasterboards
33
with pullaway strip,
for 12.5 mm boards
with pullaway strip
28,5
2
9,5
Notes on the profiles illustrated:
3767 PVC corner bead precut at one side for
curved plasterboard constructions. Profile to
be bent manually and be fixed with galvanised
clamps to maintain profile in position. Then
apply skim coat over the flanges as usual.
3780 PVC inner corner bead round. Fix first
profile with galvanised clamps, then apply
skim coat.
3776 PVC corner bead round. Before fixing of
the profile cut the plasterboard edge with a
rasp, then fix the profile with galvanised clamps
and apply skim coat.
3778 Same corner bead as ref. 3776 but
precut at one side for curved round
plasterboard constructions. Fixing as described
before.
3774 Half-round PVC rail for decorative
purposes or as guard rail horizontally. First fix
profile with galvanised clamps, then apply
skim coat.
3772 Reveal bead in PVC for decorative
shadow joints vertically or horizontally. First fix
profile with galvanised clamps, then apply
skim coat.
3768 PVC stop bead precut for curved
connections of plasterboard ceilings to round
partitions. For plasterboard thickness of 12.5 mm
with score line for 10 mm boards to bend back
at the score line and peel off strip. Bend profile
manually, fix with galvanised clamps and then
apply skim coat.
3766 PVC stop bead with pullaway strip to
mask adjacent surfaces by applying skim coat.
3784 PVC stop bead with flexible lips for flexible
and light connections of plasterboards to
timber frames, timber columns etc. Fix with
galvanised clamps, apply skim coat and then
tear off pullaway strip.
3770 PVC inner corner bead for angles of
70°–135°. Bead to be fixed with galvanised
clamps to hold bead in position.
60
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Movement Beads, Corner Beads
Picture Bead, Beads for Tiles
Drylining
Plasterboards 12.5 mm,
Tiles 8–12 mm
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Expansion joint profile, galvanised
Corner bead for tiles
stainless steel, foil protected
3226 300 – 76.0 5
See also
page 90
With PVC part
Color number white 10
For plasterboards 12.5 mm
Expansion joint profile made from
galvanized sheet metal with white
PVC expansion part for the
assumption of building joint expansions
in the wall or ceiling areas.
Movement absorption:
tension/pressure +5/–2 mm
2158
2160
2162
250
250
250
0.5
0.5
0.5
18.2
22.7
25.8
20
20
20
for 8 mm tile thickn.
for 10 mm tile thickn.
for 12 mm tile thickn.
8
10
12
7
20
PVC movement joint profile “Magic corner”, white
3750 7500 1.0 7.5 1
coil
à
75 m
See also
page 90
PVC movement joint profile with
white PVC middle part for the
formation of movement joints in
the wall or ceiling areas
corresponding to the requirements
of DIN 18181.
Fix profile with galvanized clamps
and subsequently spackle both
sides completely up to the white
PVC middle part.
Stop bead for tiles
stainless steel
2178
2180
2182
250
250
250
0.5
0.5
0.5
14.2
16.6
16.2
20
20
20
for 8 mm tile thickn.
for 10 mm tile thickn.
for 12 mm tile thickn.
30
12,5
10,5
8,5
Corner bead, stainless steel, mat, foil protected
2065
2066
2041
250
250
200
250
1.5 149.5
1.5 149.5
1.25 59.5
6
6
6
with holes for screw fixing
as 2065, without holes, to fix with adhesives
to fix with adhesives
8
10
12
2065/2066
Picture bead galvanised, Picture hooks, brass
2041
2158/2162 Corner beads made of stainless
steel for ceramic tiles of 8, 10 or 12 mm thickness
fixed with thin coat adhesive.
Surfaces protected with removable foil.
2178/2182 Stop beads made of stainless steel
suitable to corner beads ref. 2158/2162 for
ceramic tiles of 8, 10 or 12 mm thickness.
2041/2065/2066
Heavy corner beads in stainless steel, mat, to fix
with screws or with special adhesives to protect
plasterboard corners.
1118
1119
1124
250
–
–
0.56
0.80
0.80
31.7
0.40
0.40
15
25
25
Picture profile for plasterboards 12.5 mm
hook, brass
hook brass, nickel plated
See also
page 91
1118 picture guides made from galvanized
sheet metal for 12.5 mm plasterboards.
During installation into the wall areas, also
install stop profile 1131 to avoid movement
tears. Do not spackle picture guides up to
front bar, leave ca. 3 mm to avoid damage
from the sliding of the hook.
Maximum load of the hook: 0.15 kN.
Only for pure static loads (Not intended
for multimedia devices, et cetera)
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 61

Profiles and accessories for constructions according to
international standards (not approved to DIN standards)
Order no.
a
b/c
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Connector for C-ceiling profile
Ref. 5107 + 5109, galvanised
Hanger for C-ceiling profile
Ref. 5107/5108/5109, galvanised
C-ceiling profiles, galvanised,
for fixing of plasterboards
6125 9 0.6 3.9 50
6123 30 0.8 8.0 100 length = 300 mm
5107 45.5 17 0.60 40.5 10
standard length
ref. 5107 = 5.30 m
ref. 5108 = 6.00 m
ref. 5109 = 5.25 m
Hanger for C-ceiling profile
Ref. 5107/5108/5109, galvanised
17,8
6120 9.5 0.8 1.5 100
length = 95 mm
5108 47 27 0.60 53.7 8
27
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
Length/cm
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Hanger for C-ceiling profile
Ref. 5107/5108/5109, galvanised
6121 19 0.8 3.0 100 length = 190 mm
Hanger for C-ceiling profile
Ref. 5107/5108/5109, galvanised
5109 47 17 0.60 43.3 12
6124 40 0.8 12.0 100 length = 450 mm
17,2
U-Hanger galvanised, flat
for C-ceiling profiles 5107, 5108, 5109
6168 - - 0.88 3.3 100
Hanger for C-ceiling profile
Ref. 5107/5108/5109, galvanised
6122 19 0.8 3.6 100 Double hanger
length = 190 mm
62
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Studs and runners
to international standards
Profiles do not
correspond
to DIN norms.
Order no.
a
b/c
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Order no.
a
b/c
Materialthickness
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
Runners galvanised,
standard lengths 3 m
MAXI-SCW-Profiles, galvanised,
in fixed lengths
5836
5848
5870
5890
5899
5869
5849
36
48
70
90
100
70
48
28
28
28
28
28
28
28
0.56
0.56
0.56
0.56
0.56
0.56
0.56
40.0
46.1
58.2
66.1
67.5
58.2
46.1
10
10
10
10
10
8
10
}
Pre-punched
for round walls
5660
5677
68.8 47/49 0.60 92.6
88.8 47/49 0.60 102.0
4
4
“A”
68.8 mm
88.8 mm
MAXI-CW-Profiles galvanised,
in lengths up to 8 m
5936
5937
5944
5970
5990
5999
5460
5477
34.8
34.8
46
68.8
88.8
98.8
68.8
88.8
39/41
39/41
34/36
34/36
34/36
34/36
47/49
47/49
0.70
0.60
0.60
0.60
0.60
0.60
0.60
0.60
66.5
57.0
57.0
67.8
80.1
82.0
82.0
92.0
10
10
10
10
10
10
8
8
49
A
47
for improved sound absorption values of light
weight partitions incl. cable protective sleeves
ref. 6411 (4 pcs. per length) that are added.
Euroline-Profiles
U-reinforcing channel galvanised,
standard length 2.50 m
5185
5187
5189
46.8
68.8
88.8
45
45
45
1.5
1.5
1.5
155.4
181.3
204.9
4
4
4
Furring channel galvanised, for fixing of plasterboards
standard length 5.00 m
5115 35 22 0.60 46.1 10
Code number
CW 46
CW 50
CW 70
CW 75
CW 90
CW 100
CW 100
UW 48
UW 50
UW 70
UW 75
UW 90
UW 100
UW 100
Euroline number
5900
5901
5902
5903
5905
5906
5904
5805
5801
5802
5803
5807
5808
5804
Dimension a
46
48.8
68.8
73.8
88.8
98.8
98.8
48
50
70
75
90
100
100
Dimension b
36
49
36
49
36
36
49
28
30
28
30
28
28
30
Dimension c
34
47
34
47
34
34
47
28
30
28
30
28
28
30
Materialthicknes
mm
Weight/kg
100 m/pcs
Packing
pcs/lengths
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
48.0
59.0
56.0
69.0
64.0
68.0
79.0
40.0
42.0
48.0
52.0
56.0
59.0
61.0
10
8
10
8
10
10
8
10
8
10
8
10
10
8
}
Bar length
cm
300
260/300
300
260/300
350/400
300
300
300/400
300/400
300/400
300/400
300/400
300/400
300/400
300/400
Hat ceiling profile, galvanised,
for plasterboard installation bar length 300 cm
5106 43 16.5 0.56 46.1 10
UD 5806
CD 60/27 5817
28.5
60
26.6
27
26.6
27
0.50
0.50
31.0
48.0
16
12
300
300/400
H-punch out
for profiles
5901, 5903, 5904
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 63

The PROTEKTOR sound insulation programme
MAXI-SCW studs
for improved sound absorption values of light
weight partitions.
TPS 25
adjustable profile and fixing
system to improve the impact
sound absorption, especially
with timber joist ceiling
construction in prefabricated
houses.
RC channel
for wall lining in order to
improve the sound absorption
values of walls, metal frame
partitions and timber frame
partitions.
Pict . 1 Pict . 2
Pict . 1 Anti-Vibration hanger ref.6039 with highly elastic
absorption element.
Pict . 2 U-hanger ref. 6160 for the fixing of CD ceiling
profiles with highly elastic vibration absorption element.
64

MAXI-SCW studs for
improved sound insulation values
47
49
B
● Galvanised steel 0.6 mm
● Width 73.8 mm = ref. 5615
● Width 98.8 mm = ref. 5616
● Width 68.8 mm = ref. 5660
● Width 88.8 mm = ref. 5677
● Packaging: 4 lengths
per bundle
● 16 pieces of cable protection sleeves are
added to each bundle. They are to be
clipped into the service cut-outs on site.
● Standard lengths:
ref. 5615
ref. 5616
2.60, 3.00, 3.50, 4.00 metres
2.60, 3.00, 3.50, 4.00 metres and
● special lengths upon demand
● Knurled flange for easier screwing
● Wall heights as per DIN 18183
● Fire rating F 90 with 2 x 12.5 mm gypsum fire
protection plaster boards
● Sound insulation values have been verified
by the independent institute EMPA,
Dübendorf, Switzerland
● Tests for the sound insulation were carried
out with standard boards and with special
sound insulation gypsum plaster boards
● Cutting to the required length with
MAXI-SCW profile cutter art. no. 6424 for:
SCW sound insulation studs ref. 5615/5616
MAXI-CW standard studs ref. 5215/5216
UW runners ref. 5233/5234
}
}
acc. DIN
acc. international
standards
At each
end of a stud
there are
two service
cutouts for
clipping on
the cable
protection
sleeves.
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 65

Overview
Partitions and wall linings
technical data
Dimensions max. sound absorption 3) max. approx. max. height
Page Wall acc. to DIN 4109 fire weight acc. to DIN 4103/18183
rating
type D a d R WR acc. to
I 1 ) II 2 )
mm mm mm dB
DIN 4102 kg/m 2 m m
MAXI-SCW-systems Technical data refer to page 68/69
Single stud partition
single boarded
70 CW 50/75 75 50 12.5 40 F 30-A 26 3.00 2.75
70 CW 75/100 100 75 12.5 41 F 30-A 26 4.50 3.75
70 CW 100/125 125 100 12.5 47 F 30-A 26 5.00 4.25
Single stud partition
double boarded
72 CW 50/100 100 50 2 x 12.5 50 F 90-A 52 4.00 3.50
72 CW 75/125 125 75 2 x 12.5 51 F 90-A 52 5.50 5.00
72 CW 100/150 150 100 2 x 12.5 55 F 90-A 52 6.50 5.75
Single stud partition
triple boarded
74 CW 100/175 175 100 3 x 12.5 58 F 90-A 75 8.00 7.50
a
d
D
d
74 CW 125/200 200 125 3 x 12.5 58 F 90-A 75 9.00 8.00
Double stud partition
double boarded
76 CW 50 + 50/155 155 105 2 x 12.5 60 F 90-A 51 4.50 4.00
76 CW 75 + 75/205 205 155 2 x 12.5 60 F 90-A 52 6.00 5.50
76 CW 100 + 100/255 255 205 2 x 12.5 63 F 90-A 53 6.50 6.00
CW 50 + 50/160 ≥ 160 110 51 4.50 4.00
78 up to up to 2 x 12.5 54 F 90-A up to up to up to
CW 75 + 75/210 ≥ 210 160 53 6.00 5.50
Movable partition
80 CW 75/100 100 75 12.5 ca. 40 F 30-AB 28 4.50 3.50
Clamp fixing
Wall lining
3.00
82 V-CW 75/87.5 ^ 82.5 ^ 70 12.5 – – 20 up to 3.00
V-CW 100/112.5 4.00
V-CD 30/42.5 ≥ ≥
84 42.5 30 12.5 – – 20
V-UW 50/62.5
86 V2 25 13 12 – – 14
no
limit
1 ) For partitions in commercial buildings (flats, hotels, hospitals etc.) in low traffic rooms and corridors, or where the difference in floor heights, on either side of the partition, is max 1 m.
2 ) For partitions in high traffic areas (showrooms, lecture theatres, class rooms), or where the difference in floor heights, on either side of the partition, is more than 1 m.
F = only when fire-resistant plasterboards are used!
66
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Material requirements table
per m 2 (excluding waste)
Profiles
Boards
15
Page CW UW 12.5 18
m m 20
Self trapping
screws/piece
Joint strip
rm
Joint filler
kg
Felt strip
rm
Dowel
piece
Skirting
strip/rm
Mineral fibre
m 2
Hat and
covering profile
rm
ALU covering
profile
rm
Bracket
piece
Hat profile
rm
Pivot clip
piece
70 1.8 0.8 2.0 – 26 3.3 0.5 1.3 1.6 0.8 1.0 – – – – –
70 1.8 0.8 2.0 – 26 3.3 0.5 1.3 1.6 0.8 1.0 – – – – –
70 1.8 0.8 2.0 – 26 3.3 0.5 1.3 1.6 0.8 1.0 – – – – –
72 1.8 0.8 4.0 (4.0) 9+26 3.3 0.65 1.3 1.6 0.8 1.0 – – – – –
72 1.8 0.8 4.0 (4.0) 9+26 3.3 0.65 1.3 1.6 0.8 1.0 – – – – –
72 1.8 0.8 4.0 (4.0) 9+26 3.3 0.65 1.3 1.6 0.8 1.0 – – – – –
9+
9+
74 1.8 0.8 6.0 – 26 3.3 0.8 1.3 1.6 0.8 1.0 – – – – –
9+
9+
74 1.8 0.8 6.0 – 26 3.3 0.8 1.3 1.6 0.8 1.0 – – – – –
76 3.6 1.6 4.0 (4.0) 9+26 3.3 0.65 5.4 3.2 0.8 1.0 – – – – –
76 3.6 1.6 4.0 (4.0) 9+26 3.3 0.65 5.4 3.2 0.8 1.0 – – – – –
76 3.6 1.6 4.0 (4.0) 9+26 3.3 0.65 5.4 3.2 0.8 1.0 – – – – –
78 3.6 1.6 4.0 (4.0) 18+26 3.3 0.65 2.6 3.2 0.8 1.0 – – – – –
80 1.8 0.8 2.0 – 9 – – 1.3 1.6 0.8 1.0 1.5 1.8 – – –
82 1.8 0.8 1.0 – 13 1.65 0.25 1.3 1.6 0.4 1.0 – – – – –
84 – 2.4 1.0 – 13+4.8 1.65 0.25 0.7 4.0 0.4 1.0 – – 2.4 – –
timber
86 – –
1.0
– – – – – 3.6 – – – – – 1.8 16
Calculations basis: Wall surface 4.00 m x 2.50 m = 10 m 2
3 ) R WR - values according to own test results resp. data of the manufacturers of gypsum plasterboards.
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 67

MAXI-SCW systems for improved sound insulation values
Single stud partition, single or double boarded
Partition thicknesses:
95/100 mm
115/125 mm
140/150 mm
Max. partition height:
≤ 5000 mm
Fire rating:
F 30-A – F 90 A
Sound absorption:
s. list
Partition weight:
26 – 52 kg/m 2
SCW + single
layer of boards
SCW + double
layer of boards
9
8 8
11
4
5
1
6
3
10
1
2
3
4
5
6
7
8
9
10
11
Runner UW 70-100-06
MAXI-CW 70-100-06
MAXI-SCW-70-100-06
Dowel
Felt strip
Insulation material
Skirting profile
Inner corner profile ref. no. 5170
Corner bead
Gypsum plaserboard ≥12.5 mm
Joint filler
Corner detail
2
3
625/600
100 up to 150
7
1
Plan detail
Side detail
68
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

MAXI-SCW systems for improved sound insulation values
Single stud partition, single or double boarded
Partition system according to standard DIN 4103 and DIN 18183:
Non-load bearing partition system as single stud partition, either single or double layer of board on both sides.
Technical data and system code according to DIN 18183:
Profiles according to DIN 18182/1 with a nominal material thickness of 0.6 mm. Boarding with plasterboards.
Code
Partition
cavity
Total
partition
thickness
Boarding
each side
Max. partition
height
I + II
Partition
weight
mm mm mm mm kg/m 2
SCW 70/95
SCW 75/100
SCW 90/115
SCW 100/125
SCW 70/120
SCW 75/120
SCW 75/125
SCW 90/140
SCW 100/150
70
75
90
100
70
75
75
90
100
95
100
115
125
120
120
125
140
150
1 X 12.5
1 X 12.5
1 X 12.5
1 X 12.5
2 X 12.5
1 X 12.5/1 X 10.0
2 X 12.5
2 X 12.5
2 X 12.5
3250
3250
3750
3750
4250
4250
4250
5000
5000
2) Fermacell
Boarding types according to DIN 18180: GKB 12.5 mm and/or special insulation gypsum boards
fixed according to DIN 18181: GKF 12.5 mm when fire protection is required
GKBi 12.5 mm application in
GKFi 12.5 mm } humid rooms
Official test results 1) according to standard EN ISO 717-1/143-3
Calculated values R WR as per DIN 4109 = laboratory values R W reduced by –2 dB
* 12.5 + 10 mm, 2 nd layer stapled
1) Test results nos. 413821/1-8, 414620/1-8, 418049/1-10 EMPA, CH-Dübendorf
26
26/35 2)
Type of boarding material
Fire resistance
Partition type Insulation material Gypsum board Gypsum board Gypsum board FERMACELL class
code 22 kg/m 3 8.5–9.1 kg/m 2 9.9 kg/m 2 10.7 kg/m 2 12.5/15 kg/m 2 with GK. F
R WR R WR R WR R WR F
SCW 70/95 60 mm 42 dB – – – –
SCW 75/100 60 mm 43 dB 46 dB – 50 dB F 30-A
SCW 90/115 80 mm 45 dB – – – –
SCW 100/125 80 mm 45 dB 49 dB 49 dB – F 30-A
SCW 70/120 60 mm 52 dB – – - –
SCW 75/120 60 mm - – – 62 dB*) –
SCW 75/125 60 mm 52 dB 56 dB – - F 90-A
SCW 90/140 80 mm 55 dB – – – –
SCW 100/150 80 mm 53 dB 58 dB 58 dB – F 90-A
26
26
52
57 2)
52
52
52
Installation instructions:
• At the wall connection and at 90° corners use the standard MAXI-CW studs.
• Clip the cable protection sleeves (4 pieces per stud) into the service cutouts of the stud during the mounting of the insulation material.
• Adapt the insulating material to the shape of the sound insulation stud.
• Ensure tight connections to adjacent building components.
• For cutting the profiles a special MAXI-SCW-profile cutter no. 6424 has been developed.
• Boarding and joint filling according to the board manufactures.
• For door openings use reinforcing studs.
• Not suitable for partitions in sanitary rooms with sanitary equipment.
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 69

Non-loadbearing partition systems
Single stud partition, single boarded
Partition types:
CW 50/ 75
CW 75/100
CW 100/125
Max. partition heights:
I 3000 – 5000 mm
II 2750 – 4250 mm
Fire rating:
F 30-A
Sound absorption: 3)
R WR 40 – 47 dB
Partition weight:
26 kg/m 2
Partition thicknesses:
75 mm
100 mm
125 mm
T-junction
Corner junction
75 up to 125
Horizontal section
Vertical section
1
2
3
4
Runner 50-100-06
Stud 50-100-06
Dowel
Felt strips
5
6
7
8
Insulating material
Skirting profile
Inner corner bead ref. 5170
Corner protecting bead
9
10
≥12.5 mm plasterboard
Joint filling
70
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Non-loadbearing partition systems
Single stud partition, single boarded
Partition system according to DIN 4103 and DIN 18183:
Non-loadbearing partition systems as single stud partition, single boarded on both sides.
Technical data and system code according to DIN 18183:
Profiles according to DIN 18182/1 with a nominal material thickness of 0.6 mm.
Partition
Max partition height
Code Partition thickness Boarding Application Partition
cavity in total each side field 1) weight
I II
mm mm mm mm kg/m 2
CW 50/ 75 50 75 1 x 12.5 3000 2750 26
CW 75/100 75 100 1 x 12.5 4500 3750 26
CW 100/125 100 125 1 x 12.5 5000 4250 26
1) I For partitions in commercial buildings (flat,
hotels, hospitals, etc.) in low traffic rooms
and corridors, or where the difference in
floor heights, on either side of partition, is
max. 1 m.
II For partitions in heigh traffic areas (showrooms,
lectrue theatres, class rooms) or
where the difference in floor heights, on
either side of the partition, is more than 1 m.
Boarding types according to DIN 18180: GKB 12.5 mm without further demands
fixed according to DIN 18181: GKF 12.5 mm when fire protection is required
GKBi 12.5 mm application in
GKFi 12.5 mm } humid rooms
Sound absorption values according to DIN 4109 (Calculation values) 3)
Fire protection values according to DIN 4102/4
Type of fire
Rate of
Code Insulating material thickness resistance sound absorption
mm F R WR
CW 50/ 75 40 F 30-A 40 dB
CW 75/100 60 F 30-A 41 dB
CW 100/125 80 F 30-A 47 dB
R WR = evaluated sound absorption rate of
partition without longitudinal transmission over
flanking construction elements.
Calculation values for proof procedure.
3) According to existing test results, tested with
different gypsum plaster boards of different
manufacturers.
Requirements to fibrous insulating materials:
For fire protection: Building material type A, melting point KT ≥ 1000 °C
For sound protection: Longitudinal flow resistance Ξ ≥ 5 kN · s/m 4
Material requirements per m 2 (excluding waste):
Calculation basis: partition surface 4.00 x 2.50 = 10 m 2
Code
5230
Runners 1 Studs 2 Dowels 3 Felt strip 4
Self tapping screws
ref./rm ref./rm ref./pcs ref./rm ref./pcs
5233
5234
5211
5215
5216
6187
(6194)
6188
(6195)
6189
6248 6205 6206 6208
(6196)
CW 50/ 75 0.8 1.8 1.6 1.3 26
CW 75/100 0.8 1.8 1.6 1.3 26
CW 100/125 0.8 1.8 1.6 1.3 26
Reinforcing profiles, accessory profiles for drylining etc. on demand.
Attention: When boarding the fixing system with other boarding materials, i.e. fibrous plasterboards, special fire protecting boards, particle
boards etc. please observe the technical datas and fixing instructions of the manufacturer!
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 71

Non-loadbearing partition systems
Single stud partition, double boarded
Partition types:
CW 50/100
CW 75/125
CW 100/150
Partition thicknesses:
100 mm
125 mm
150 mm
Max. partition heights:
I 4000 – 6500 mm
II 3500 – 5750 mm
Fire rating:
F 60-A – F 90-A
Sound absorption: 3)
R WR 50 – 55 dB
Partition weight:
52 kg/m 2
T-junction
Corner junction
100 up to 150
Horizontal section
Vertical section
1
2
3
4
Runner 50-100-06
Stud 50-100-06
Dowel
Felt strips
5
6
7
8
Insulating material
Skirting profile
Inner corner bead ref. 5170
Corner protecting bead
9
10
≥ 2 x 12.5 mm plasterboard
Joint filling
72
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Non-loadbearing partition systems
Single stud partition, double boarded
Partition sytem according to DIN 4103 and DIN 18183:
Non-loadbearing partition systems as single stud partition, double boarded on both sides.
Technical data and system code according to DIN 18183:
Profiles according to DIN 18182/1 with a nominal material thickness of 0.6 mm.
Partition
Max partition height
Code Partition thickness Boarding Application Partition
cavity in total each side field 1) weight
I II
mm mm mm mm kg/m 2
CW 50/100 50 100 2 x 12.5 4000 3500 52
CW 75/125 75 125 2 x 12.5 5500 5000 52
CW 100/150 100 150 2 x 12.5 6500 5750 52
1) I For partitions in commercial buildings
(flats, hotels, hospitals, etc.) in low
traffic rooms and corridors, or
where the difference in floor heights,
on either side of partition, is max. 1 m.
II For partitions in high traffic areas
(showrooms, lecture theatres, class rooms)
or where the difference in floor heights,
on either side of the partition, is more
than 1 m.
Boarding types according to DIN 18180: GKB 12.5 mm without further demands
fixed according to DIN 18181: GKF 12.5 mm when fire protection is required
GKBi 12.5 mm application in
GKFi 12.5 mm humid rooms
}
Sound absorption values according to DIN 4109 (Calculation values) 3)
Fire protection values according to DIN 4102/4
Type of fire
Rate of
Code Insulating material thickness resistance sound absorption
mm F R WR
CW 50/100 40 F 60-A 50 dB
CW 75/125 40 F 90-A 51 dB
CW 100/150 80 F 90-A 55 dB
R WR = evaluated sound absorption rate of
partition without longitudinal transmission over
flanking construction elements.
Calculation values for proof procedure.
3) According to existing test results, tested with
different gypsum plaster boards of different
manufacturers.
Requirements to fibrous insulating materials:
For fire protection: Building material type A, melting point KT ≥ 1000 °C.
Material requirements per m 2 (excluding waste):
Calculation basis: partition surface 4.00 x 2.50 = 10 m 2
Code
5230
Runners 1 Studs 2 Dowels 3 Felt strip 4
Self tapping screws
ref./rm ref./rm ref./pcs ref./rm ref./pcs
5233
5234
5211
5215
5216
6187
(6194)
6188
(6195)
6189
6248 6205 6206 6208
(6196)
CW 50/100 0.8 1.8 1.6 1.3 9 26
CW 75/125 0.8 1.8 1.6 1.3 9 26
CW 100/150 0.8 1.8 1.6 1.3 9 26
Reinforcing profiles, accessory profiles for drylining etc. on demand.
Attention: When boarding the fixing system with other boarding materials, i.e. fibrous plasterboards, special fire protecting boards, particle
boards etc. please observe the technical datas and fixing instructions of the manufacturer!
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 73

Non-loadbearing partition systems – single stud partition,
triple boarded – oversized partitions, fire rated
Partition types:
CW 100/175
CW 125/200
Partition thicknesses:
175 mm
200 mm
Max. partition heights:
I 7500–9000 mm
II 7500–9000 mm
Fire rating:
F 90-A
Sound absorption: 3)
R WR 58 dB
Partition weight:
75 kg/m 2
T-junction
Corner junction
175 up to 200
Horizontal section
Vertical section
1
2
3
4
Runner 100-125-06
Stud 100-125-06
Dowel
Felt strips
5
6
7
8
Insulating material
Skirting profile
Inner corner bead ref. 5170
Corner protecting bead
9
10
≥ 3 x 12.5 mm plasterboard
Joint filling
74
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Non-loadbearing partition systems – single stud partition,
triple boarded – oversized partitions, fire rated
Partition system according to DIN 4103 and DIN 18183:
Non-loadbearing partition systems as single stud partition, triple boarded on both sides.
Technical data and system code according to DIN 18183:
Profiles according to DIN 18182/1 with a nominal material thickness of 0.6 mm.
Partition
Max partition height
Code Partition thickness Boarding Application Partition
cavity in total each side field 1) weight
I II
mm mm mm mm kg/m 2
CW 100/175 100 175 3 x 12.5 8000 7500 75
1) I For partitions in commercial buildings
(flats, hotels, hospitals, etc.) in low
traffic rooms and corridors, or
where the difference in floor heights,
on either side of partition, is max. 1 m.
II For partitions in high traffic areas
(showrooms, lecture theatres, class rooms)
or where the difference in floor heights,
on either side of the partition, is more
than 1 m.
CW 125/200 125 200 3 x 12.5 9000 8000 75
Boarding types according to DIN 18180:
fixed according to DIN 18181: GKB 12.5 mm without further demand
GKF 12.5 mm when fire protection is required
GKBi 12.5 mm application in
GKFi 12.5 mm } humid rooms
Sound absorption values according to DIN 4109 (Calculation values) 3)
Fire protection values according to DIN 4102/4
Type of fire Rate of
Code Insulating material thickness resistance sound absorption
mm F R WR
CW 100/175 40 F 90-A 58 dB
CW 125/200 40 F 90-A 58 dB
Requirements to fibrous insulating materials:
For fire protection: Building material type A, melting point KT ≥ 1000 °C
For sound protection: Longitudinal flow resistance Ξ ≥ 5 kN · s/m 4
Material requirements per m 2 (excluding waste):
R WR = evaluated sound absorption rate of
partition without longitudinal transmission
over flanking construction elements.
Calculation values for proof procedure.
3) According to the information of the
manufacturers of gypsum plaster boards.
Code
Runners 1 Studs 2 Dowels 3 Felt strip 4
Self tapping screws
ref./rm ref./rm ref./pcs ref./rm ref./pcs
5234
5248
5216
5141
6187
(6194)
6188
(6195)
6189
6248 6205 6206 6208
(6196)
CW 100/175 0.8 1.8 1.6 1.3 9 9 26
CW 125/200 0.8 1.8 1.6 1.3 1.3 9 9 26
Reinforcing profiles, accessory profiles for drylining etc. on demand.
Attention: When boarding the fixing system with other boarding materials, i.e. fibrous plasterboards, special fire protecting boards, particle
boards etc. please observe the technical datas and fixing instructions of the manufacturer!
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 75

Partition types:
CW 50 + 50/155
CW 75 + 75/205
CW 100 + 100/255
Partition thicknesses:
155 mm
205 mm
255 mm
Max. partition heights:
I 4500–6500 mm
II 4000–6000 mm
Fire rating:
F 60-A – F 90-A
Sound absorption: 3)
R WR 57–63 dB
Partition weight:
51–53 kg/m 2
Non-loadbearing partition systems – double stud partition,
double boarded – for higher sound absorption
T-junction
Corner junction
155 up to 255
Horizontal section
Vertical section
1
2
3
4
2 x Runner 50-100-06
2 x Stud 50-100-06
Dowell
Felt strips
4A
5
6
7
Duplex scotch tape
Insulating material
Skirting profile
Inner corner bead ref. 5170
8
9
10
Corner protecting bead
≥ 2 x 12.5 mm plasterboard
Joint filling
76
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Non-loadbearing partition systems – double stud partition,
double boarded – for higher sound absorption
Partition sytem according to DIN 4103 and DIN 18183:
Non-loadbearing partition system as double stud partition, double boarded on both sides.
Technical data and system code according to DIN 18183:
Profiles according to DIN 18182/1 with a nominal material thickness of 0.6 mm.
Partition
Max partition height
Code Partition thickness Boarding Application Partition
cavity in total each side field 1) weight
I II
mm mm mm mm kg/m 2
CW 50 + 50/155 105 155 2 x 12.5 4500 4000 51
CW 75 + 75/205 155 205 2 x 12.5 6000 5500 52
CW 100 + 100/255 205 255 2 x 12.5 6500 6000 53
Boarding types according to DIN 18180: GKB 12.5 mm without further demands
fixed according to DIN 18181: GKF 12.5 mm when fire protection is required
GKBi 12.5 mm application in
GKFi 12.5 mm humid rooms
Sound absorption values according to DIN 4109 (Calculation values) 3)
Fire protection values according to DIN 4102/4
Type of fire
Rate of
Code Insulating material thickness resistance sound absorption
mm F R WR
CW 50 + 50/155 40 F 60-A 59 dB
CW 50 + 50/155 2 x 40 F 90-A 60 dB
CW 75 + 75/205 40 F 60-A 57 dB
CW 75 + 75/205 2 x 40 F 90-A 60 dB
CW 100 + 100/255 80 F 60-A 60 dB
CW 100 + 100/255 2 x 80 F 90-A 63 dB
Requirements to fibrous insulating materials:
For fire protection: Building material type A, melting point KT ≥ 1000 °C
For sound protection: Longitudinal flow resistance Ξ ≥ 5 kN · s/m 4
Material requirements per m 2 (excluding waste):
Calculation basis: partition surface 4.00 x 2.50 = 10 m 2 }
1) I For partitions in commercial buildings
(flats, hotels, hospitals, etc.) in low
traffic rooms and corridors, or
where the difference in floor heights,
on either side of partition, is max. 1 m.
II For partitions in high traffic areas
(showrooms, lecture theatres, class rooms)
or where the difference in floor heights,
on either side of the partition, is more
than 1 m.
R WR = evaluated sound absorption rate of
partition without longitudinal transmission
over flanking construction elements.
Calculation values for proof procedure.
R’ WR = evaluated sound absorption rate with
flanking construction elements.
Area related dimensions m’L using 300 kg/m 2 .
3) According to the information of the
manufacturers of gypsum plaster boards.
Code
5230
Runners 1 Studs 2 Dowels 3 Felt strip 4 Self tapping screws
ref./rm ref./rm ref./pcs ref./rm ref./pcs
5233
5234
5211
5215
5216
6175
6176
6248 6205 6206 6208
CW 50 + 50/155 1.6 3.6 3.2 5.4 9 26
CW 75 + 75/205 1.6 3.6 3.2 5.4 9 26
CW 100 + 100/255 1.6 3.6 3.2 5.4 9 26
Reinforcing profiles, accessory profiles for drylining etc. on demand.
Attention: When boarding the fixing system with other boarding materials, i.e. fibrous plasterboards, special fire protecting boards, particle
boards etc. please observe the technical datas and fixing instructions of the manufacturer!
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 77

Partition types:
CW 50 + 50/≥ 160
CW 75 + 75/≥ 210
Partition thicknesses:
≥ 160 mm
≥ 210 mm
Max. partition heights:
I 4500–6000 mm
II 4000–5500 mm
Fire rating:
F 30-A – F 90-A
Sound absorption: 3)
R WR 54 dB
Partition weight:
51–53 kg/m 2
Non-loadbearing partition systems – double stud partition,
double boarded – installation partitions
T-junction
Corner junction
≥ 160 up to ≥ 210
Horizontal section
Vertical section
1
2
3
4
2 x Runner 50-75-06
2 x Stud 50-75-06
Dowel
Felt strips
5
6
7
8
Insulating material
Skirting profile
Plasterboard strips 12.5 mm
Corner protecting bead
9
10
≥ 2 x 12.5 mm plasterboard
Joint filling
78
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Non-loadbearing partition systems – double stud partition,
double boarded – installation partitions
Partition system according to DIN 4103 and DIN 18183:
Non-load bearing partition as metal double stud partition supported against each other with double planking as installation partition.
Technical data and system code according to DIN 18183:
Profiles according to DIN 18182/1 with a nominal material thickness of 0.6 mm.
Partition
Max. partition height
Code Partition thickness Boarding Application Partition
cavity in total each side field 1) weight
I II
mm mm mm mm kg/m 2
CW 50 + 50/≥ 160 ≥ 100 ≥ 160 2 x 12.5 4500 4000 51
1) I For partitions in commercial buildings
(flats, hotels, hospitals, etc.) in low
traffic rooms and corridors, or
where the difference in floor heights,
on either side of partition, is max. 1 m.
II For partitions in high traffic areas
(showrooms, lecture theatres, class rooms)
or where the difference in floor heights,
on either side of the partition, is more
than 1 m.
CW 75 + 75/≥ 210 ≥ 160 ≥ 210 2 x 12.5 6000 5500 53
Boarding types according to DIN 18180: GKB 12.5 mm without further demands
fixed according to DIN 18181: GKF 12.5 mm when fire protection is required
GKBi 12.5 mm application in
GKFi 12.5 mm
}
humid rooms
Sound absorption values according to DIN 4109 (Calculation values) 3)
Fire protection values according to DIN 4102/4
Required Insulating material Type of fire Rate of
Code thickness regarding fire protection resistance sound absorption
mm kg/m 3 F R WR
CW 50 + 50/≥ 160 40 15 F 30-A 54 dB
CW 50 + 50/≥ 160 40 30 F 90-A 54 dB
CW 75 + 75/≥ 210 60 50 F 90-A 54 dB
Requirements to fibrous insulating materials:
For fire protection: Building material type A, melting point KT ≥ 1000 °C
For sound protection: Longitudinal flow resistance Ξ ≥ 5 kN · s/m 4
R WR = evaluated sound absorption rate of
partition without longitudinal transmission over
flanking construction elements.
Calculation values for proof procedure.
R’ WR = evaluated sound absorption rate with
flanking construction elements.
Area related dimensions m’L using 300 kg/m 2 .
3) According to the information of the
manufacturers of gypsum plaster boards.
Material requirements per m 2 (excluding waste):
Calculation basis: partition surface 4.00 x 2.50 = 10 m 2
Code
5230
Runners 1 Studs 2 Dowels 3 Felt strip 4 Self tapping screws
ref./rm ref./rm ref./pcs ref./rm ref./pcs
5233
5234
5211
5215
5216
6187
(6194)
6188
(6195)
6189
(6196)
6248 6205 6206 6208
CW 50 + 50/≥ 160 1.6 – 3.6 – 3.2 2.6 – 18 26
CW 75 + 75/≥ 210 1.6 – 3.6 – 3.2 2.6 – 18 26
Reinforcing profiles, accessory profiles for drylining etc. on demand.
Attention: When boarding the fixing system with other boarding materials, i.e. fibrous plasterboards, special fire protecting boards, particle
boards etc. please observe the technical datas and fixing instructions of the manufacturer!
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 79

Non-loadbearing partition systems – single stud partition,
single boarded in clamping installation, movable
Partition type:
CW 75/100
Partition thickness:
100 mm
Max. partition height:
I 4500 mm
II 3500 mm
Fire rating:
F 30-AB
Sound absorption: 3)
R WR ~ 40 dB
Partition weight:
28 kg/m 2
T-junction
Corner junction
Horizontal section
Vertical section
1 Runner 75-06
5 Insulating material
2 Stud 75-06
6 Inner corner bead ref. 5170
3 Dowel
7 Hat profile + PVC socle profile
4 Felt strips
7A Aluminum socket
Profiles and accessories Pos. 7 to 11 are variable, also see page 53.
8 Alu exterior corner + clip profile
9 Alu inner corner + clip profile
10
Hat profile + Alu/PVC covering profile
10A Hat profile + Alu/PVC filling profile
11 Alu covering profile + clip profile
*
*
*
Profiles have been removed from the range
of products offered
*
80
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Non-loadbearing partition systems – single stud partition,
single boarded in clamping installation, movable
Partition sytem according to DIN 4103 and DIN 18183:
Non-load bearing partition as metal single stud partition with double sided single plasterboard boarding in clamping installation, movable
upon request.
Technical data and system code according to DIN 18183:
Profiles according to DIN 18182/1 with a nominal material thickness of 0.6 mm.
Partition
Max. partition height
Code Partition thickness Boarding Application Partition
cavity in total each side field 1) weight
I II
mm mm mm mm kg/m 2
CW 75/100 75 100 1 x 12.5 4500 3500 28
1) I For partitions in commercial buildings
(flats, hotels, hospitals, etc.) in low
traffic rooms and corridors, or
where the difference in floor heights,
on either side of partition, is max. 1 m.
II For partitions in high traffic areas
(showrooms, lecture theatres, class rooms)
or where the difference in floor heights,
on either side of the partition, is more
than 1 m.
Boarding types according to DIN 18180: GKB 12.5 mm without further demands
fixed according to DIN 18181: GKF 12.5 mm when fire protection is required
GKBi 12.5 mm application in
GKFi 12.5 mm } humid rooms
Sound absorption values according to DIN 4109 (Calculation values) 3)
Fire protection values according to DIN 4102/4
Required Insulating material Type of fire Rate of
Code thickness regarding fire protection resistance sound absorption
mm kg/m 3 F R WR
CW 75/100 40 40 F 30-AB ca. 40 dB
R WR = evaluated sound absorption rate of
partition without longitudinal transmission
over flanking construction elements.
Calculation values for proof procedure.
R’ WR = evaluated sound absorption rate with
flanking construction elements.
Area related dimensions m’L using 300 kg/m 2 .
3) without proof
Requirements to fibrous insulating materials:
For fire protection: Building material type A, melting point KT ≥ 1000 °C
For sound protection: Longitudinal flow resistance Ξ ≥ 5 kN · s/m 4
Material requirements per m 2 (excluding waste):
Calculation basis: partition surface 4.00 x 2.50 = 10 m 2
Runner Stud Dowel Felt strip Socket Clamping Connection Self tapping
profile to ceiling screws
1 2 3 4
7 + 7A 10 + 10 + 11
*
Code Nr. 5233 Nr. 5215 Nr. 6248 Nr. 6188 Nr. 6227
rm rm pcs rm rm rm rm pcs
CW 75/100 0.8 1.8 1.6 1.3 0.8 1.8 0.8 9
7
11
*
Profiles and accessories Pos. to are variable, also see page 53.
Attention: When boarding the fixing system with other boarding materials, i.e. fibrous plasterboards, special fire protecting boards, particle
boards etc. please observe the technical datas and fixing instructions of the manufacturer!
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 81

Wall lining type:
V-CW 75/ 87.5
V-CW 100/112.5
Thickness of wall lining:
≥ 87.5 mm
≥ 112.5 mm
Fire protection:
not considered
Free standing facing plywood with metal studs
single boarded
Sound absorption:
according to solid wall
∆R’ WR up to 12 dB
Areal thermal resistance:
according to thickness of
insulating material
1/Λ max. 1.56 m 2 · K/W
T-junction
Horizontal section
Vertical section
1
2
3
4
Runner 75-100-06
Stud 75-100-06
Dowel
Felt strips
5
6
7
8
Insulating material
Skirting profile
Plasterboard ≥ 12.5 mm with vapour seal at exterior walls
Joint filling
82
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Free standing facing plywood with metal studs
single boarded
Wall lining system as single boarded fixing system made of detached studs without connection to the solid wall to improve thermal
protection and/or sound absorption.
Refering to fire protection wall linings are not taken into consideration.
Technical data and system code according to DIN 18183:
Profiles according to DIN 18182/1 with a nominal material thickness of 0.6 mm.
Min. Thickness of Max. partition height Weight of
Code lining wall lining Boarding Application wall
distance in total one side field 2) lining
I II
mm mm mm mm kg/m 2
V-CW 75/ 87.5 75 ≥ 87.5 ≥ 12.5 3000 2500 20
V-CW 100/112.5 100 ≥ 112.5 ≥ 12.5 4000 3000 20
Boarding types according to DIN 18180: 12.5 mm without further demands 1)
fixed according to DIN 18181: 12.5 mm application in humid rooms 1)
Sound absorption values according to DIN 4109 insert 1
Extract from chart 1 + 8, construction according to chart 7, line 2.
1) When boarding exterior construction
elements and using insulating material
made of mineral fibre provide vapour seals.
i.e. by using plasterboards covered with
aluminium foil on the backside, or
corresponding foils between studs and
boarding.
2) I For partitions in commercial buildings
(flats, hotels, hospitals, etc.) in low
traffic rooms and corridors, or
where the difference in floor heights,
on either side of the partition, is max. 1 m.
II For partitions in high traffic areas
(showrooms, lecture theatres, class rooms)
or where the difference in floor heights,
on either side of the partition, is more
than 1 m.
Area related dimensions Tested rate of sound absorption Tested rate of sound absorption
of the solid wall without wall lining with wall lining
kg/m 2 R’ WR R’ WR
100 37 dB 49 dB
150 41 dB 49 dB
200 44 dB 50 dB
250 47 dB 52 dB
300 49 dB 54 dB
400 52 dB 56 dB
500 55 dB 58 dB
Areal thermal resistance 1/Λ according to DIN 4108
Thickness of mineral fibre insulation 1/Λ
mm
in m 2 · K/W
20 0.73
30 0.98
40 1.23
50 1.45
60 1.56
Requirements to fibrous insulating materials for insulation layer:
For sound protection: Longitudinal flow resistance Ξ ≥ 5 kN · s/m 4
Remark: The technical data in the above stated tables is valid for DIN constructions.
Further constructions with technical data please refer to the information of the different manufacturers of boarding materials.
Material requirements per m 2 (excluding waste):
Calculation basis: partition surface 4.00 x 2.50 = 10 m 2
Runners Studs Felt Self-tapping
1
2
strip Dowels screws
Code ref./rm ref./rm ref./rm 4 ref./pcs ¬ 3 ref./pcs
5233 5234 5215 5216 6188 6189 6248 6205
V-CW 75/ 87.5 0.8 – 1.8 – 1.3 – 1.6 13
V-CW 100/112.5 – 0.8 – 1.8 – 1.3 1.6 13
Accessory profiles for drylining etc. on demand.
Attention: When boarding the fixing system with other boarding materials, i.e. fibrous plasterboards, special fire protecting boards, particle
boards etc. please observe the technical datas and fixing instructions of the manufacturer!
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com
83

Wall lining with adjusting brackets
single boarded
Wall lining type:
V-CD 30/42.5
V-UW 50/62.5
Thickness of wall lining:
≥ 42.5 mm
≥ 62.5 mm
Fire protection:
not considered
Sound absorption:
according to solid wall
∆R’ WR up to 12 dB
Arial thermal resistance:
according to thickness of
insulating material
1/Λ max. 1.56 m 2 · K/W
Horizontal section V-CD
1
Horizontal section V-UW
1A
Vertical section
1
1A
C-ceiling profile 60-06 ref. 5120
Runner 50-06 ref. 5230
3
4
Self.-tapping screw ref. 6239
U-connection profile ref. 5168 or ref. 5244
6
7
Plaster board ≥ 12.5 mm with vapour seal at exterior walls
Dowel ref. 6248
2
Adjusting bracket ref. 6156
5
Felt strip ref. 6180
2A
Adjusting bracket ref. 6155 +
6149, 6150, 6151
5A
Felt strip ref. 6187
84
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Wall lining with adjusting brackets
single boarded
Wall lining system as single boarded fixing system with C-ceiling profiles or runners fixed at solid wall with adjusting brackets
to improve thermal protection and/or sound absorption.
Refering to fire protection wall linings are not taken into consideration.
Technical data and system code according to DIN 18183:
Profiles according to DIN 18182/1 with a nominal material thickness of 0.6 mm.
Min. Thickness of Weight of
Code lining wall lining Boarding wall
distance in total one side lining
mm mm mm kg/m 2
1) When boarding exterior construction
elements and using insulating material
made of mineral fibre provide vapour seals.
i.e. by using plasterboards covered with
aluminium foil on the backside, or
corresponding foils between studs and
boarding.
V-CD 30/42.5 30 ≥ 42.5 ≥ 12.5 20
V-UW 50/62.5 50 ≥ 62.5 ≥ 12.5 20
Boarding types according to DIN 18180: 12..5 mm without further demands 1 )
fixed according to DIN 18181: 12.5 mm application in humid rooms 1 )
Sound absorption values according to DIN 4109 insert 1
Extract from chart 1 + 8, construction according to chart 7, line 2.
Area related dimensions Tested rate of sound absorption Tested rate of sound absorption
of the solid wall without wall lining with wall lining
kg/m 2 R’ WR R’ WR
100 37 dB 49 dB
150 41 dB 49 dB
200 44 dB 50 dB
250 47 dB 52 dB
300 49 dB 54 dB
400 52 dB 56 dB
500 55 dB 58 dB
Areal thermal resistance 1/Λ according to DIN 4108
Thickness of mineral fibre insulation 1/Λ
mm
in m 2 · K/W
20 0.73
30 0.98
40 1.23
50 2 ) 1.45
60 2 ) 1.56
Requirements to fibrous insulating materials:
For sound protection: Longitudinal flow resistance Ξ ≥ 5 kN · s/m 4
Material requirements per m 2 (excluding waste):
Calculation basis: partition surface 4.00 x 2.50 = 10 m 2
5 7
5A
pcs 2 pcs 2A m 1 m 4 m 1A
m pcs pcs 3 pcs
Accessory profiles for drylining etc. on demand.
2) For large insulating layer thicknesses,
adjusting bracket ref. 6149 or U-hanger
ref. 6157 are to be used as wall attachments.
Remark: The technical data in the above stated tables is valid for DIN constructions.
Further constructions with technical data please refer to the information of the different manufacturers of boarding materials.
Adjusting Adjusting C-ceiling U-connection Runner Felt strip Dowel Self-tapping screws
bracket bracket profile profile ref. 6180
Code ref. 6156 ref. 6155 ref. 5120 ref. 5168 ref. 5230 ref. 6187 ref. 6248 ref. 6239 ref. 6205
V-CD 30/42.5 2.4 – 2.0 0.4 – 0.7 2.4 4.8 13
V-UW 50/62.5 – 2.4 – – 2.4 0.7 2.4 4.8 13
Attention: When boarding the fixing system with other boarding materials, i.e. fibrous plasterboards, special fire protecting boards, particle
boards etc. please observe the technical datas and fixing instructions of the manufacturer!
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 85

Wall lining system V2 for timber panels
ref. 6148/6146
Wall
Groove depth 5 or 7 mm
Groove
ref . 5143
ref . 6131–6139
1
2
3
4
5
hat profile ref. 5143
Timber panel twist clips
ref. 6131–6139 or
nut and spring twist clips
ref. 6146 or 6148
ceiling
wall
timber panel
wall lining V2
Combination of lining system V2 with ceiling system K 1400.
86
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Dry lining with furring channel Ref. 5112
with plasterboards or plasterboard thermal laminates
ref. 5112
Length: 2.30 m, 4.00 m
10 pcs/bundle
Fixing instructions:
– check and pretreat masonry according to plaster manufacturer instructions
– fix and adjust the horizontal profiles with gypsum plaster dabs
– fix and adjust the vertical profiles with gypsum plaster dabs, a gap of 5 cm should be left between the horizontal and vertical profiles
for utilities
– in case of weak substrates an additional mechanical fixing is required to avoid furrings working loose when fixing the plasterboards
– the perforated profile area must be completely imbedded in the dabs
– the distance »A« of the vertical profiles corresponds to the plasterboard manufacturers recommendations, depending on board size,
type etc.
– after the plaster dabs are set, screw on the board with the self tapping screws and joint it for painting
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 87

Glazing with standard profiles
for assembly on site
≤ 1250
≤ 1250
STANDARD CONSTRUCTION WITH LARGE PVC-COVER JOINT PROFILE
1
2
3
4
5
U-RUNNER
ALU-U-PROFILE 77, 102 OR 127 mm
FELT STRIP 3 mm OR FIBROUS WEB
HAT PROFILE ref. 5156
TEKS SCREW ref. 6218
6
7
8
9
GLAZING PROFILE ref. 6554
WINDOW PANE 4–6 mm
PVC-COVER JOINT PROFILE ref. 3765
PLASTERBOARD 12.5 mm
ALTERNATIVE CONSTRUCTION WITH SMALL ALU OR PVC-COVER
JOINT PROFILE (not applicable for windows placed side by side)
4a
5a
6a
7a
8a
HAT PROFILE ref. 5143
TEKS SCREW ref. 6227
GLAZING PROFILE ref. 6555
WINDOW PANE 4 mm
ALU OR PVC-COVER JOINT ref. 6578 or 3762
88
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Glazing with standard profiles
for assembly on site
SECTION
B – B
SECTION
A – A
SECTION
C – C
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 89

Forming of expansion and movement joints
Methods of forming expansion joints
in metal stud partition systems
Single boarding with expansion joint profile ref. 3226. ref. 3226
Galvanised sheet metal with PVC-part, white.
Length: 3.00 m, bar/flange
Double boarding with expansion joint profile ref. 3226.
When installing the wall system, care should be taken that gaps are left
between the connecting channels on the floor and ceiling in the same
width as the expansion joints.
Forming of movement joints
in a suspended plasterboard ceiling.
Suspended plasterboard ceiling with installed movement joint profile
ref. 3750.
It is recommended to tack the profile additionally with galvanised
clamps.
ref. 3750
PVC movement joint profile, white
Length: 75 m coil/box.
According to DIN 18181 movement joints have to be fixed if plasterboard
wall and ceiling surfaces are 15 m, also if ceiling surfaces are
reduced, e.g. in case of projecting wall. This instruction has to be
observed to avoid cracking.
90
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Installation of heavy corner profiles, flush
Obtuse-angled formation
Right-angled formation
1
2
3
Exterior corner profile, 135°, ref. 5445
Interior corner profile, 135°, ref. 5444
Heavy corner profile, 135°, ref. 5193
4
5
6
Heavy corner profile, 90°, ref. 5192
Interior corner profile, ref. 5170
Plasterboard strip (in case of fire protection)
Fixing possibilities of picture profile Ref. 1118
ceiling
Only for pure static loads
(Not appropriate for multimedia devices, et cetera)
ceiling
Alternative:
Installation in wall area
Do not fill up to the
front edge of the
profile. There should
be approx. 3 mm
from the front edge
to the filling material.
1
2
3
4
5
6
7
Picture profile ref. 1118
Picture hook ref. 1119 or 1124
Stop profile ref. 1131
Plasterboard 12.5 mm
Felt strip
U-runner
C-stud
Fixing directly under the ceiling
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 91

33 33
Fixing of PVC stop bead with pullaway strip Ref. 3766
Fixing of PVC corner profile Ref. 3767 for curved corners
Fixing sample:
Partition fixed under suspended grid ceiling or similar. Protection of ceiling surface by pullaway strip when skimming wall. Because of the
S-shape of the PVC stop bead an elastic ceiling connection is obtained (e.g. ceilings, wooden construction elements).
ADJUST STOP BEAD
WITH PULLAWAY STRIP
PULL AWAY THE STRIP
AFTER SMOOTHING AND/OR
HARDENING OF FILLER.
CEILING REMAINS CLEAN!
ref. 3766
PVC stop bead
with pullaway strip
length 3.00 m, 35 pcs/box
Fixing sample:
Door opening with circular arch with PVC corner profile. The profile which is only perforated at one side is curved by hand and skimmed.
It is recommended to tack the profile with 2 galvanised clamps in order to avoid movement when smoothing.
3
Ref. 3767
PVC corner bead, white,
precut for curved
plasterboard corners
length 3.00 m, 20 pcs/box
92
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Fixing of the frames of doors at normal CW studs,
Room height ≤ 2.60 m
Door width ≤ 0.90 m
Weight of the door leaf incl. mounting ≤ 25 kg
Sub construction
Fixing scheme
1
2
Guide-lines for the installation of
a door in partition systems
3
Boarding scheme
4
Zargenbefestigung an verstärkten U-Aussteifungsprofilen,
Room height > 2.60 m and/or
Door width > 0.90 m and/or
Weight of the door leaf incl. mounting > 25 kg
Fixing scheme
5
1
Opening
for leading
cable
through
2
3
2
1
1
2
3
U runner
C stud
Lintel profile prepunched ref.
5261–5263 fastened by rivets
4
5
6
7
UW-profile
UA-profile
UA-angle
Plug angle
6
7
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 93

Sliding connections at
partition systems
Sliding ceiling connection
Sliding ceiling connections with
reinforcing channels in the door area
9
1
1 + 2
4
H
2
5
3 3
7A
≥ 500
6
6
H
3
8
7
6
> H
9
Sliding wall connections
1
1
5
2
4
6
1
2
3
4
5
6
7
7A
8
9
Connection thickness
(for F-wall with glass fiber strips)
Bundle of gypsum plasterboard strips
U runner for sliding ceiling connections
ref. 5236 - 5238
“Göppinger profile” ref. 9299
Stop profile ref. 9002
C stud 50-100-0.6
Reinforcing channel 50-100-2.0
UA-profile as sliding profile L ≥ 500 mm
Attach the profile for this with self-securing hexagonal
nuts to the lengthwise holes on the stiffening (UA) profile
in a manner so that it can slide.
Hexagonal nuts without self-securing must be provided
with a counter nut.
Lintel profile ref. 5261 - 5263
fastened by rivets
Fixing angle ref. 6185, 6183 or 6182
fastened with dowels and screwed
Alternative plug angle set
see also page 93
94
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

PROTEKTOR
Bearing studs and traverses
for metal stud partitions
and concealed installations

Product Information
Protektor profile bearing studs and traverses for the solid attachment of sanitary
objects to metal stud partitions and facing boards.
• Sturdy bearing stud systems designed for installation in metal stud walls according to DIN 18183
and usable with pre-assembled support elements as concealed wall structures.
• All metal parts are hot-galvanized.
• All the bearing studs can be vertically adjusted via telescope legs or bases.
• All attachment fixtures for feed water and waste water as well as for the sanitary objects themselves
can be adjusted vertically and horizontally.
• All pipe clamps are fitted with noise-insulating rubber inserts to avoid flowing sounds.
• The installation boards for the sink bearing stud and traverses have been designed both for conventional
water connections and for soundproofed connections with the necessary diameters and
pitch measurements.
• The respective bearing elements are delivered complete, as illustrated, including the installation
accessories listed and an installation manual.
• All the parts can also be used for concealed wall installation in dry walls without modifications
being necessary.
• All the bearing studs must be screwed to the stud profiles at the side and dowelled into the screed
floor using base plates. Care must always be taken that the bearing stud is installed flush with the
front edge of the stud profile.
• In compliance with ATV DIN 18340 (issue 2006), special sanitary brackets for wall-hung toilets and
bidets must be attached on both sides to reinforced stud profiles (U bracing profiles including
connecting angles and screw attachments).
• For installation in room-high facing boards, the bearing studs must be supported against the masonry
or U bracing profiles including connecting angles and screw attachments must be used as stud
profiles.
• Generally speaking, double panelling must be planned on both sides when 12.5 mm impregnated
GKBI panels are used for metal stud partitions with installed sanitary bearing studs.
• Pipe and attachment ducts through the panelling must be cut out cleanly with a diameter of
approx. 10 mm, the cutting edges must be primed and sealed with permanently elastic, fungicide
jointing putty.
• Please follow the processing instructions of the panelling manufacturer.
• Consult the plumbing company at an early stage to arrange and specify the installation workflows,
any installed parts, dimensions etc.
96
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau
Tel. (0 72 25) 9 77-0 . Fax (0 72 25) 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Protektor bearing stud no. 56852
for installing a wall-hung toilet with in-wall flushing cistern from Geberit
GEBERIT flushing cistern
with dual volume flush to be pressed from the front.
Delivery proof for flushing plate to be mounted on site: Geberit
Flushing cisterns from other manufacturers are also available as special equipment on request.
Accessories included:
2 x threaded rods M 12 x 180
4 x key screws 8 x 70 with
washers and dowels
Product description: Order no. 56852
Protektor bearing stud for the installation of a wall-hung toilet in metal stud walls with in-wall flushing cistern from "Geberit". All the metal
parts are galvanised. The plastic pipe fitting set for Ø 50 mm feed pipe and Ø 100/80 mm waste pipe is pre-assembled. The pipes themselves
are contained in the box. The fastening structure can be vertically adjusted continuously after 4 screws have been loosened.
The fastening distance for WC attachment is 180 mm.
The width of the bearing studs is 470 mm for a stud axis distance of 520 mm.
The minimum cavity space required is 170 mm.
Weight 13.7 kg / unit
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau
Tel. (0 72 25) 9 77-0 . Fax (0 72 25) 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 97

Protektor auxiliary bearing stud no. 56851
for mounting supporting fittings and/or gripping handles
Accessories included:
4 x key screws 8 x 70
with washers and dowels
Product description: Order no. 56851
Protektor auxiliary bearing studs for metal stud partitions for the attachment of supporting handles and similar
aids for the handicapped. The objects are screwed to a multi-layer wooden board 25 mm thick. The
auxiliary bearing studs can be installed independently as individual parts in any post-and-beam structure.
Weight 6.8 kg / unit or 13.0 kg / pair
98
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau
Tel. (0 72 25) 9 77-0 . Fax (0 72 25) 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Protektor bearing stud no. 56831
for one-sided sink attachment
Accessories included:
2 x hanger bolts M 10 x 160
2 x nuts M10 with washers
4 x key screws 8 x 70
with washers and dowels
Product description: Order no. 56831
Protektor bearing stud for the attachment of sinks to metal stud partitions.
All the metal parts are galvanised. A vertically-adjustable multi-layer wooden board 25 mm thick is installed
for the sink attachment. The two attachment plates for corner valve installation are prepared for all common
installations.
The minimum cavity space required is 100 mm.
Weight 9.1 kg / unit
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau
Tel. (0 72 25) 9 77-0 . Fax (0 72 25) 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 99

Protektor bearing stud no. 56835
for sink attachment
Accessories included:
UP cover
2 x threaded rods M 10 x 160
2 x protective hoses
2 x wall ducts
1 x UP siphon
4 x nuts M10 with washers
4 x key screws 8 x 70
with washers and dowels
Product description: Order no. 56835
Protektor bearing studs for the attachment of sinks or wash basins. All the metal parts are galvanised. Operation
above or below the sink is possible by moving the wall duct brackets.
The minimum cavity space required is 75 mm.
Weight 11.0 kg / unit
100
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau
Tel. (0 72 25) 9 77-0 . Fax (0 72 25) 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Protektor bearing stud no. 56840
for the installation of wall-hung urinals
Accessories included:
2 x threaded rods M 8 x 120
4 x nuts M10 with washers and cover caps
4 x key screws 8 x 70
with washers and dowels
Product description: Order no. 56840
Protektor bearing studs for the attachment of urinals to metal stud partitions. All the metal parts are galvanised.
The mounting plate has system holes and can be mounted at 3 different heights depending on the
flushing system to be installed, using the two threaded rods Ø 8 x 120 mm included with 2 nuts and washers
each. There is a vertically-adjustable drain pipe clamp with a sound-insulating rubber insert mounted on the
mounting plate.
The position of the fittings box with system holes can be continually adjusted both vertically and horizontally.
The minimum cavity space required depends on the planned flushing/operation set used.
Weight 10.8 kg / unit
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau
Tel. (0 72 25) 9 77-0 . Fax (0 72 25) 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 101

Protektor bearing stud no. 56837
for mounting supporting fittings and/or gripping handles
Accessories included:
2 x threaded rods M 12 x 180
2 x protective hose
4 x key screws 8 x 70
with washers and dowels
Product description: Order no. 56837
Protektor bearing studs for the attachment of wall-hung urinals to metal stud partitions. All the metal parts
are galvanised. The drain pipe clamp with a sound-insulating rubber insert is vertically adjustable. The
fastening structure can be continually vertically adjusted after 4 screws have been loosened.
The minimum cavity space required is 100 mm.
Weight 10.63 kg / unit
102
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau
Tel. (0 72 25) 9 77-0 . Fax (0 72 25) 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Protektor traverses no. 56832
for lightweight hand wash basins
Product description: Order no. 56832
Protektor traverses for the installation of lightweight
hand wash basins. All the metal parts are galvanised.
The hand wash basin is attached to a multi-layer
wooden board 25 mm thick which has two exchangeable
boards pre-mounted for the adjustable installation
of corner valves in conventional installation or
reversed for pipe-in-pipe installation. A drain pipe
clamp Ø 50 mm with rubber insert is also pre-mounted.
The traverses is mounted using 4 x M8 x 20 screws with
nuts and washers with the post-and-beam structure.
The minimum cavity space required is 100 mm.
The multi-layer wooden board 545 mm wide can be
moved sideways, this makes the traverses suitable for
use with bearing stud distances of 600 or 625 mm; it
can also be cut to a smaller size on site for smaller
bearing stud distances if necessary.
Weight 4.7 kg / unit
Protektor traverses no. 56833
multi-purpose wooden traverses
Product description: Order no. 56833
Protektor traverses for mounting gripping handles,
hand rails etc.. All the metal parts are galvanised.
The products are attached to a multi-layer wooden
board 25 mm thick. The traverses is mounted using
4 x M8 x 20 screws with nuts and washers with the
post-and-beam structure.
The multi-layer wooden board 545 mm wide can be
moved sideways, this makes the traverses suitable for
use with bearing stud distances of 600 or 625 mm; it
can also be cut to a smaller size on site for smaller
bearing stud distances if necessary.
The multi-layer wooden board 545 mm wide can be
moved sideways, this makes the traverses suitable for
use with bearing stud distances of 600 or 625 mm; it
can also be cut to a smaller size on site for smaller
bearing stud distances if necessary.
Weight 4.1 kg / unit
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau
Tel. (0 72 25) 9 77-0 . Fax (0 72 25) 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 103

Protektor bearing studs in concealed wall structures
Installation examples
Fig.: Front view of bearing studs
Fig.: Mounting bracket (A) can be continuously
adjusted via threaded rods for support and
attachment of the bearing studs on the masonry
All protector bearing studs have mounting brackets fitted in the factory, so that they can be used both in standard
mounting or installation walls or in concealed wall structures or installation without conversion work or
retrofitting being necessary.
Brief description of concealed wall installation using the example of the sink bearing stud no. 56835 illustrated:
Before installation work starts, the vertical adjustment on the bearing stud is carried out by moving and fixing the
bases, whereby both bases can be adjusted independently. Then the bearing stud is set up according to the planned
concealed wall design and fixed to the floor.
The mounting brackets (A) required for concealed wall installation and pre-fitted in the factory can be turned continuously
clockwise or anti-clockwise. Depth adjustment is by means of an Allen key (size 8) and can be carried out
before and/or after the support fixtures have been fastened to the masonry.
After the bearing stud has been installed, the post-and-beam structure is mounted around it. In order to achieve precise
and straight edges, we recommend planning the post-and-beam structure approx. 50 mm higher, inserting a
UW profile onto the CW studs from above and using an UW profile to connect the structure to the masonry as well.
This makes panel mounting much easier later. The CW studs must be connected to the bearing stud using sheet
metal screws.
Protektor cross-beam no. 56838
for fittings
Product description: Order no. 56838
Protektor fittings traverses for mounting various sanitary
fittings to metal stud partitions. The U-shaped
metal traverses has system holes Ø 8.5 mm and
Ø 4.2 mm, can be moved horizontally with CW studs
(≥ 75 mm) and must be mounted using the screws
provided. The traverses is galvanised.
CW studs width ≥ 75 mm for correct sanitary
installation.
The width of the traverses is 570 mm for a stud axis
distance of 625 mm.
Weight: 2.4 kg / unit
104
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau
Tel. (0 72 25) 9 77-0 . Fax (0 72 25) 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

UK reinforcement plate for wall-hung loads no. 6670
Wood screw with Pozidrive slot,
size 2, galvanised
Order no.
6212
6213
Length/cm
4.5
7.0
Material thickness/mm
Weight/kg
100 m/unit
Packaging
units
5
5
0.48
0.72
250
250
Coated, for suspended
installation on wooden
components,
e.g. wire with eyelet or
UK reinforcement plate
no. 6670
5.0 x 45 mm
5.0 x 70 mm
Product description: Order no. 6670
The UK reinforcement plate (galvanised, dimensions 625 x 300 x 0.7 mm) is used for mounting wall cupboards, shelves,
radiators etc..
The reinforcement plate is clicked in place between the CW studs and fixed using the crimping tool. After panelling
has been completed, wall load fastenings can be mounted without pre-drilling being necessary using a quick-action
screwdriver and special screws no. 6212 or 6213. The use of special cavity dowels is no longer required.
Load table:
Permissible cupboard weight G (kN) with GK single panelling (1 x 12.5 mm)
or GK double panelling (2 x 12.5 mm),
for attachment with 2 screws of the type 5 x 45 no. 6212 or 5 x 70 no. 6213.
Load table:
Single panelling Double panelling
1 x 12.5 mm GK 2 x 12.5 mm GK
perm. FQ = 0.56 kN
perm. FZ = 0.32 kN
perm. FQ = 0.72 kN
perm. FZ = 0.53 kN
D (mm) 100 200 300 400
H (mm)
G (KN)
1 x 12.5 2 x 12.5 1 x 12.5 2 x 12.5 1 x 12.5 2 x 12.5 1 x 12.5 2 x 12.5
200
0.78 0.60 0.48 0.41
1.07 0.86 0.71 0.61
400
0.92 0.78 0.68 0.60
1.23 1.07 0.95 0.86
600
0.98 0.87 0.78 0.71
1.29 1.17 1.07 0.99
800
1.01 0.92 0.84 0.78
1.33 1.23 1.15 1.07
1000
1.03 0.95 0.89 0.83
1.35 1.27 1.20 1.13
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau
Tel. (0 72 25) 9 77-0 . Fax (0 72 25) 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 105

Drylining tools
1
ref. 6432 MAXI-profile cutting
for cutting of UW- and CWprofiles
and UD-profiles for
up to 0.7 mm thickness,
without punching device
and length feed stop.
ref. 6424 MAXI-SCW-profile cutter
for cutting MAXI-SCW studs
ref. 5615 (75 mm),
ref. 5616 (100 mm),
C studs ref. 5215 (75 mm),
ref. 5216 (100 mm) and
U runners
ref. 5233 (75 mm) and
ref. 5234 (100 mm)
for
backfitting
of
ref.
6432
}
2
3
4
ref. 6427 spare blade for ref. 6432
ref. 6426 spare dorn for ref. 6432
for punching ø 25 mm
ref. 6429 thorn and die-plate
for punching ø 25 mm
ref. 6430 thorn and die-plate
for punching ø 6,2 mm
ref. 6431 length feed stop 280 mm
ref. 6517 Hand metal snips
ref. 6485 Crimping tongs
for jointing metal profiles without
rivets. Steel thickness 2 x 0.8 mm
ref. 6486 Spare thorn
for crimping tongs ref. 6485
ref. 6487 Spare upper part
for crimping tongs ref. 6485
ref. 6510 Elektro-metal-cutter
type 1001
for cutting of galv. metal profiles,
cutting strength:
sheet iron up to 1.3 mm
Nirosta up to 1.0 mm
soft metal up to 2.0 mm
ref. 6515 Spare blade
for Electro-metal-cutter
ref. 6510 (not shown)
ref. 6516 Spare jaw
for Electro-metal-cutter
ref. 6510 (not shown)
ref. 6412 Punching tool
for later perforation of studs up
to 1.0 mm
material thickness for pipes,
cable or pipe Ø 23 mm
ref. 6435 Electro-profile-nibbler
for cutting of galv. metal profiles
up to 2.0 mm thickness.
Can also be delivered batterypowered.
ref. 6514 Pop-rivet-tongs
for riveting of profiles for rivet
diameters of 3.0; 3.2 and 4 mm
ref. 6436 Spare plate
for ref. 6435 (not shown)
ref. 6437 Spare-die
for ref. 6435 (not shown)
ref. 6438 Spare matrix
for ref. 6435 (not shown)
ref. 6511 Hand cutter
with wire cutter Ø < 3 mm
for manual cutting of steel
profiles.
Nr. 6513 Hand riveting tongs
to secure pivot clipses on
profiles
ref. 6512 Spare blade
for hand cutter, ref. 6511
(not shown)
106
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

Example for dry lining of the attic
Lintel profile
Hatceiling
profile
ref. 5114
C stud
U reinforcement
channel
Connection sealing
Connect angle
+ install set ref. 6203
(alternative to door
post angle set)
U runner
Reinforcement plate
ref. 6670
Horizontal bar for light
weight hand wash
basin ref. 6832
Support stud for hanging WC
with concealed cistern
ref. 6852
PROTEKTOR is part of HeinzeBauOffice
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau . Germany
Tel. +49 (0) 72 25 9 77-0 . Fax +49 (0) 72 25 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com 107

Technical conditions of delivery
1. Profiles and stampings produced by Protektor are normally made of galvanised steel according to DIN EN 10142 and DIN EN 10143.
2. Departing from table 2 in DIN EN 10143 our profiles are manufactured according to considerably closer thickness tolerances in the individual nominal values as per our factory specifications.
3. The protection against corrosion in our profiles and stampings are corresponding to the demands of DIN 18168 and/or DIN 18182/1. Cut edges are not additionally protected. We recommend
to stock these profiles in dry places.
4. We reserve the right to produce our profiles and stampings of other materials but corresponding in its quality to mentioned DIN standards.
5. All our profiles and stampings are manufactured for application in normal internal atmospheres according to DIN 18168 table 2, line 1. In case of special demands (e.g. for outdoor application,
in humid rooms) they have to be provided with an additional protection against corrosion according to DIN 18168 and/or DIN 55928/8 at site,
6. For production the already mentioned DIN standards as well as DIN 59413, 6930 and 6935 are valid. Closer tolerances are only valid according to written agreement.
7. All the constructions indicated in our catalogue have to be installed according to our installation regulations and/or test certificates. They are designed according to the requirements of the
DIN standards as indicated in this catalogue. Apart from these – concerning installation – the prescriptions of manufacturers of the materials not delivered by Protektor have to be observed.
A guarantee can only be given if all construction elements are delivered by Protektor.
8. As far as delivery of special constructions according to customer’s requirement is concerned we are not able to give any guarantee regarding stability.
9. Special profiles or accessories according to customer’s indication are only manufactured without liability regarding violation of possible protection rights a third person may have (patents etc.).
10. Deliveries of special lengths, profiles or accessories acc. point 9. cannot be returned. Regarding special elements we reserve the right to deliver 10% more or less.
11. Regarding orders of special colour-coated elements we have to know the total quantity you need to avoid deviations of coating. Regarding repeat orders we are not able to give a guarantee
against possible deviations in coating. These items cannot be returned.
12. The above mentioned special profiles and/or accessories can only be manufactured according to written orders and presentation of corresponding drawings and material specifications.
13. All indications and illustrations made in our catalogues are without engagement. This is also valid for remarks made by ourselves verbally if they are not confirmed in writing. Misprints cannot be
excluded.
14. We reserve the right to change products or types of packing and/or packing standards without announcement in advance.
15. With publication of this catalogue all editions published before become invalid.
16. These technical conditions of delivery are part of aur sales conditions.
108
PROTEKTORWERK . Florenz Maisch GmbH & Co. KG . Viktoriastraße 58 . D-76571 Gaggenau
Tel. (0 72 25) 9 77-0 . Fax (0 72 25) 9 77-4 44 . http://www.protektor.com . e-mail: info@protektor.com

We are represented in following European countries
AUSTRIA:
BELGIUM/
LUXEMBURG:
CZECH REPUBLIC:
DENMARK:
ESTONIA:
FRANCE:
GREAT BRITAIN:
HUNGARY:
IRELAND:
PROTEKTOR Bauprofile GmbH
Postfach 45
A-1211 Wien
Tel. 01/2 59 45 00-0
Fax. 01/2 59 45 00-19
Neue Adresse ab 15.10.2007
Hosnedlgasse 12
A-1220 Wien
I.G.M S.A.
Rue Saint Nicolas 283
B-4000 Liège
Tel.: 0 42/24 12 11
Fax: 0 42/24 10 15
Masterplast Plus s.r.o.
Mladoboleslavská 132
CZ-19700 Praha 9 - Vinor
Tel.: 02/86 85 03 86
Fax: 02/86 85 03 86
Profitec Nordic ApS
Roholmsvej 15
DK-2620 Albertslund
Tel.: 0 45/76 95 95
Fax: 0 45/76 14 30
Betotrade OÜ
Kadaka tee 3
EE-10621 Tallinn/Eesti
Tel.: 07/30 22 77
Fax: 07/30 22 75
PROTEKTOR S.A.
BATI-PROFIL
Rue Pasteur Prolongée
F-94400 Vitry sur Seine
Tel.: 01/55 53 17 50
Fax: 01/55 53 17 40
Cornercare Ltd.
Unit 3 + 4
Walter Nash Road West
Birchen Coppice Industrial Estate
Oldington
GB-Kidderminster, Worcs. DY11 7RA
Tel.: 0 15 62/51 52 00
Fax: 0 15 62/86 40 63
PROTEKTORWERK HUNGARIA Kft.
Jászberény út 38 - 72
H-1106 Budapest
Tel.: 01/2 60 43 08
Fax: 01/2 61 05 49
BUILDING PROFILES & SYSTEMS LTD.
Unit C2
Bluebell Ind. Estate
IRL-Dublin 12
Tel. 01/4 60 08 51/8 52
Fax. 01/4 60 08 53
Activities also in countries in the Middle and Far East.
ITALY:
LATIVA:
LITHUANIA:
THE NETHERLANDS:
NORWAY:
POLAND:
SERBIA-
MONTENEGRO:
SPAIN:
SWITZERLAND:
ERNESTO MARIOTTI
Itrac S.R.L.
Fraz. Poggio S. Ercolano
I-06020 Gualdo Tadino (Perguia)
Tel.: 0 75/9 10 72 40
Fax: 0 75/9 10 72 40
SIA Tapeks
Ganibu Dambis 25 DF
LV-1005 Riga
Tel.: 7 09-76 68
Fax: 7 55-00 01
EUROSTATYBA
Kalvariju 2
LT-2005 Vilnius
Tel.: 0 52/31 82 79
Fax: 0 52/31 82 79
CEVES VERGEER
Bouwprodukten
Postbus 2087
NL-7420 AB Deventer
Tel.: 05 70/50 38 30
Fax: 05 70/50 38 31
HELE INDUSTRI a.s.
Skarersletta 50
N-1473 Lorenskog
Tel.: 0 67/98 04 40
Fax: 0 67/98 04 44
Bernard Sidor
Przedstawiciel Protektor Polska
ul. Powstanców Slaskich 20
PL-66400 Gorzów Wlkp.
Tel.: / Fax: 0 95/7 23 04 56
Mobile: 06 01/75 28 96
D. O. O. ZA Proizvodnju Promet
“Nimon” Ivanjica
Ulica Krajiskih Brigada 20
SCG-32250 Ivanjica
Tel.: 0 32/66 45 69
Fax: 0 32/66 45 69
Daniel Fernández Sosa
Jefe de ventas
Protektorwerk
Sant Ferran N° 4, piso 2° puerta 1 a
E-08205 Sabadell (Barcelona)
Móvil: 0 60 9 02 37 68
Fax: 09 37/12 42 48
Distributor
RALTEC S.A.
Poligono Industrial Areta
C/Badostain, S/N
E-31620 Huarte/Pamplona
Tel.: 09 48/31 29 12
Fax: 09 48/31 70 49
PROTEKTOR Profil GmbH
Riedthofstrasse 172
CH-8105 Regensdorf
Tel.: 01/843 14 14
Fax: 01/843 14 24