STANDBY 560 ekW 700 kVA 50 Hz 1500 rpm 400 Volts - Finning (UK)
STANDBY 560 ekW 700 kVA 50 Hz 1500 rpm 400 Volts - Finning (UK)
STANDBY 560 ekW 700 kVA 50 Hz 1500 rpm 400 Volts - Finning (UK)
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>STANDBY</strong> <strong>560</strong> <strong>ekW</strong> <strong>700</strong> <strong>kVA</strong><br />
<strong>50</strong> <strong>Hz</strong> 1<strong>50</strong>0 <strong>rpm</strong> <strong>400</strong> <strong>Volts</strong><br />
®<br />
TECHNICAL DATA<br />
Open Generator Set - - 1<strong>50</strong>0 <strong>rpm</strong>/<strong>50</strong> <strong>Hz</strong>/<strong>400</strong> <strong>Volts</strong><br />
Low Fuel Consumption<br />
DM7544<br />
Generator Set Package Performance<br />
Genset Power rating @ 0.8 pf<br />
Genset Power rating with fan<br />
Fuel Consumption<br />
100% load with fan<br />
75% load with fan<br />
<strong>50</strong>% load with fan<br />
Cooling System 1<br />
Air flow restriction (system)<br />
Air flow (max @ rated speed for radiator arrangement)<br />
Engine Coolant capacity with radiator/exp. tank<br />
Engine coolant capacity<br />
Radiator coolant capacity<br />
<strong>700</strong> <strong>kVA</strong><br />
<strong>560</strong> <strong>ekW</strong><br />
146.4 L/hr 38.7 Gal/hr<br />
103.9 L/hr 27.4 Gal/hr<br />
71.2 L/hr 18.8 Gal/hr<br />
0.12 kPa 0.48 in. water<br />
660 m³/min 23308 cfm<br />
81.8 L 21.6 gal<br />
20.8 L 5.5 gal<br />
61.0 L 16.1 gal<br />
Inlet Air<br />
Combustion air inlet flow rate 41.5 m³/min 1465.6 cfm<br />
Exhaust System<br />
Exhaust stack gas temperature<br />
Exhaust gas flow rate<br />
Exhaust flange size (internal diameter)<br />
Exhaust system backpressure (maximum allowable)<br />
Heat Rejection<br />
Heat rejection to coolant (total)<br />
Heat rejection to exhaust (total)<br />
Heat rejection to aftercooler<br />
Heat rejection to atmosphere from engine<br />
Heat rejection to atmosphere from generator<br />
Alternator 2<br />
Motor starting capability @ 30% voltage dip<br />
Frame<br />
Temperature Rise<br />
557.7 º C 1035.9 º F<br />
122.0 m³/min 4308.4 cfm<br />
203 mm 8 in<br />
10.0 kPa 40.2 in. water<br />
176 kW 10009 Btu/min<br />
<strong>560</strong> kW 31847 Btu/min<br />
128 kW 7279 Btu/min<br />
92 kW 5232 Btu/min<br />
38.3 kW 2178.1 Btu/min<br />
1681 s<strong>kVA</strong><br />
LC7024J<br />
1<strong>50</strong> º C 270 º F<br />
Lube System<br />
Sump refill with filter 38.0 L 10.0 gal<br />
Emissions (Nominal) 3<br />
NOx mg/nm3<br />
CO mg/nm3<br />
HC mg/nm3<br />
PM mg/nm3<br />
2965.1 mg/nm³<br />
<strong>400</strong>.5 mg/nm³<br />
11.3 mg/nm³<br />
15.2 mg/nm³<br />
1<br />
For ambient and altitude capabilities consult your Caterpillar dealer. Air flow restriction (system) is added to existing restriction from<br />
factory.<br />
2<br />
Generator temperature rise is based on a 40º C (104º F) ambient per NEMA MG1-32.<br />
3<br />
Emissions data measurement procedures are consistent with those described in EPA CFR 40 Part 89, Subpart D & E and ISO8178-1 for<br />
measuring HC, CO, PM, NOx. Data shown is based on steady state operating conditions of 77ºF, 28.42 in HG and number 2 diesel fuel<br />
with 35º API and LHV of 18,390 btu/lb. The nominal emissions data shown is subject to instrumentation, measurement, facility and engine<br />
to engine variations. Emissions data is based on 100% load and thus cannot be used to compare to EPA regulations which use values<br />
based on a weighted cycle.<br />
4<br />
February 28 2008 11:17 AM