Ametek 900 ADA PDF

PERFORMANCE SPECIFICATIONS
Methodology: Multiple wavelength, high resolution,
non-dispersive UV
Species Minimum Maximum
Measured Full Scale Full Scale
H 2 S 5000 ppm 10%
SO 2 2500 ppm 10%
CS 2 5000 ppm 10%
COS 5000 ppm 10%
Sv 50 ppm 500 ppm
Accuracy 1 : Better than 1% full scale
Reproducibility 1 : Better than 0.5% full scale
Linearity 1 : Better than 1% full scale
Response Time: Typically less than 30 s to T 90 (excl. sample
system)
Number of Gases: Up to 5 simultaneously (refer to AMETEK for
possible combinations)
Power: 120 VAC +10%, 47-63 Hz or 220 VAC +10%, 47-63 Hz
600 W (for analyzer only)
Approvals and Certifications
NEC/CEC Class I, Division 2, Groups C & D
CENELEC EEx pd IIB T3
GOST 1ExpdIIBT3 (certification pending)
Complies with all relevant European Directives
GOST Pattern Approval
Typical Sample Flow: 3 to 5 1/min (0.1 to 0.2 SCFM)
Sample Transport: Air aspiration
Temperature Control: Independent control of four zones
(oven, sample line, probe, vent line)
Pressure and Temperature Compensation: Standard
Ambient Temperature: 41 O F to 122 O F (5 O C to 50 O C)
Instrument Air: Minimum 30 psig, 1 CFM; instrument quality air
Physical Dimensions: 61 x 44 x 12 in. (1554 x 1118 x 305 mm)
Weight: Approximately 250 to 350 lbs. (115 to 160 kg)
Communications:
Analog 4 x 4 to 20 mA self powered
Digital One RS-422 with Modbus protocol
Relays 3 independent sets of SPDT relays alarm conditions
1. NOTE: Stated specifications apply to SO 2 and H 2 S only. Please consult factory for
specifications on other species.
IN
(MM)
ALLOW MIN.
10.0 (254.0)
OVEN DOOR
OUTLINE
2.94
(74.7)
44.0
(1117.6)
42.25
(1073.2)
SAMPLE LINE
CONNECTION
3/8 IN.
SWAGELOK
Ø 1.76 (44.6)
(2 PLACES)
VENT LINE
CONNECTION
1/2 IN.
SWAGELOK
27.12
(688.8)
ANALYZER
OVEN
58.99
(1498)
SAMPLE
INLET
ELECTRONICS
ENCLOSURE
DOOR OUTLINE
ELECTRONICS
ENCLOSURE
BLANK PLATE
RECOMMENDED
ENTRY LOCATION
FOR PROBE HTR/
RTD CONDUIT
NOTE:
SAMPLE INLET/VENT
HOLE LOCATIONS ARE
BASED ON THE
RECOMMENDED
MOUNTING HEIGHT
SHOWN ON THE
FRONT VIEW.
55.05
(1398)
SAMPLE
VENT
ALLOW MIN.
27.8 (706.0)
DOOR SWING
41.44
(1052.7)
RECOMMENDED
HEIGHT
27.12
(688.8)
3.99
(101.3)
SAMPLE/VENT
LINE & PROBE
TERMINATION BOX
8 x 6 x 3.5 IN.
3/4 IN.
CONDUIT (A)
3/4 IN.
CONDUIT (B)
USE 3/8 x 1-1/2 IN.
STUDS
(6 PLACES)
FLOOR
FLOOR
One of a family of innovative process analyzer solutions from AMETEK Process Instruments. Specifications subject to change without notice.
PROCESS INSTRUMENTS
CANADA CHINA FRANCE GERMANY USA - Delaware USA - Texas
2876 Sunridge Way N.E. Rm #B5, 16F Harvest Bldg. 3 Avenue Des Coudriers Postfach 2165 455 Corporate Blvd 9750 Whithorn Drive
Calgary, AB T1Y 7H9 #585 Long Hua Xi Road Z.A. De L’Observatoire D-40644 Meerbusch OR Newark, DE 19702 Houston, TX 77095
Ph. 403-235-8400 Shanghai, 200232 78180 Montigny Le Bretonneux Rudolf-Diesel-Str. 16 Ph. 302-456-4400 Ph. 281-463-2820
Fax 403-248-3550 Ph. 86 21 64 284 067 Ph. 33 1 30 64 89 70 D-40670 Meerbusch Fax 302-456-4444 Fax 281-463-2701
Fax 86 21 64 875 329 Fax 33 1 30 64 89 79 Ph. 49 21 59 91 36 0
Fax 49 21 59 91 3680
www.ametekpi.com
© 2001, by AMETEK, Inc. All rights reserved.
901PDF (080116)