Swing T5 pendant And Surface With Elliptical Diffuser

swing T5 pendant and surface WITH elliptical diffuser
13 SERIES
Direct/Indirect White Elliptical Perforated Diffuser
with Acrylic Backing
1.1"
4.8"
TYPE:
order number:
PROJECT:
Pendant
Model # Length Wattage
SW42114.213 2’ 14
SW42124.213 2’ 24
SW43121.313 3’ 21
SW43139.313 3’ 39
SW44128.413 4’ 28
SW44154.413 4’ 54
NOTE: For continuous runs,
please see the ST4 series.
Surface
Model # Length Wattage
SW52114.213 2’ 14
SW52124.213 2’ 24
SW53121.313 3’ 21
SW53139.313 3’ 39
SW54128.413 4’ 28
SW54154.413 4’ 54
Model# Voltage Options* Dimming*
*See back page for details.
16.5"
23.6" / 35.4" / 47.2"
23.6" / 35.4" / 47.2"
1–120V
2–277V
Please review mounting info before ordering.
Dimming/emergency not available on series SW5.
SEM13
SMB
SWRB
1.38"
SD1
SD3
SD5
SD8
2.5"
1.8"
4.2"
4.8"
4.8"
SW4 & SW5/13
burbank,
california,
91505
www.
delray
lighting.
com
JUN 2010

4’ 54w
sWING construction
OPTIONS
1-54W T5
SW44154.413
1-54W T5 HO
G5 socket
Total lumens: 5000 mean
Total luminaire efficiency: 92.8%
• Cast zinc aluminum alloy
and aluminum extrusion
construction.
• G5 twist-in lamp holders.
• UL /cUL listed for damp
locations.
Single lamp pendant
• 8 ft. field-adjustable air craft
cable suspension, with push
button glider.
• Adjustble 8’ gray 600V,
18/5 AWG power cords.
• Dimming and emergency
battery available.
• Universal standard output
120/277V, 50/60 Hz
electronic ballast, in a
remote housing.
• Back plate has 7 /8”opening for
direct conduit feed.
Single lamp SURFACE
• Integral universal standard
output 120/277V, 50/60 Hz
electronic ballast.
• Back plate has threaded 7 /8”
opening for direct 16 AWG
conduit feed.
• Dimming and EM not available.
dimming ballasts
Dimming ballast replaces standard
canopy. All ballasts require
compatible dimmers. Note: pendant
distance should not exceed 3 feet.
Voltage must be specified.
Cat. # Type Wattage
SD1 Lutron Eco 10 28/54
SD3 Advance Mark X 54
SD5 Advance Mark VII 54
SD8 Lutron Hi Lume FDB 28/54
23.5" x 2”sq.
CP DISTRIBUTION
mounting – sW4 and SW5 series
180°
827
620
414
207
0
150°
120°
90°
Swing features a die cast backplate with a threaded 1 /2” conduit fitting at one
end for direct connection to flexible conduit, which provides the smallest ballast
compartment profile and avoids unsightly plates or covers on walls or ceilings.
Use a third party 1 /2” conduit fitting and maximum 14 AWG wire for
communication to the ballast. Detailed installation instructions are available at
www.delraylighting.com.
7.3”
000000000000000000000000000000000000000000000000000000
emergency ballasts
Emergency ballast provides 1300
lumens for 90 minutes. Charge
indicator light and test switch visible
from below. (Remote test switch
available.) Emergency not available
for the SW5 series. Voltage must be
specified. Order SEM13.
207
414
620
827
30°
Vertical plane thru Horiz. 0 - 180°
Vertical plane thru Horiz. 90 - 270°
COEFFICIENTS
60°
Pendant mount shown with separate ballast housing.
C L Pendant ballast housing placement is only
limited by the length of cord available.
IMPORTANT: cord enters the side of
the ballast housing (not the bottom),
at the end opposite the primary power.
Ballast housing mounts to the ceiling
with provided anchor screws.
47.25"
recessed ballast
For suspended ceilings only.
Order SWRB.
% CEILING 80 (20% FLOOR)
% WALL 70 50 30
0 93 93 93
1 84 79 76
2 76 69 63
3 69 60 53
4 63 53 46
5 58 47 39
6 53 42 34
7 49 37 30
8 45 34 27
9 42 31 24
10 39 28 21
Ceiling or Wall
Ballast back plate mounts directly
to the wall or ceiling with anchor
screws provided.
C L
Surface mount shown with integral ballast housing.
7.3”
000000000000000000000000000000000000000000000000000000
NOTE: POWER DOES NOT ENTER AT THE CENTER
J-BOX MOUNT
Use third party 1 /2” conduit fitter
and maximum 14 AWG wire for
connection to ballast compartment.
Clamp connectors provided.
BALLAST HOUSING Box cover
thru wiring
Replaces standard ballast canopy
and dimming canopy. Allows up
to 1 /2”conduit with 3-in/3-out,
#14 AWG. Order SmB.
23.5" x 2”sq.
Mounting the SW4 and SW5 series
with standard ballast housing to a
recessed J-box requires a 3” mud ring,
the holes in line with the direction of
the fixture. Order SW200, available
in S–silver or W–white.
6.75” from ballast
center to box
center
Order S100P to mount ballast to
a recessed J-box. For use with the
following options:
• SEM13
• Dimming
5"
SW5–PENDANT MOUNT
Adjustable cable gripers, round power
feed canopy, and 8’ cable and power
cord included. (Cable and power cord
may be ordered any length). Order
SW5PS–silver or SW5PW–white. .07"
5"
JUN 2010