Safety data sheet - BASF Construction Chemicals Pacific

More documents

Recommendations

Info

Page: 4/9 BASF Safety data sheet Date / Revised: 17.10.2012 Version: 1.0 Product: MASTERFLOW 678 DP PLUS PTB (30559173/SDS_GEN_AU/EN) Date of print 17.10.2012 Further information on storage conditions: Keep only in the original container in a cool, dry, wellventilated place away from ignition sources, heat or flame. Protect from direct sunlight. Store protected against freezing. Storage stability: Storage temperature: 5 - 35 °C The packed product is not damaged by low temperatures or by frost. The packed product will not be damaged by high temperatures. 8. Exposure controls and personal protection Components with occupational exposure limits The substances without values are not listed in the occupational exposure regulations for the validity area of this safety data sheet. no exposure standard allocated Personal protective equipment Respiratory protection: Wear respiratory protection if ventilation is inadequate. Combination filter for gases/vapours of organic, inorganic, acid inorganic and alkaline compounds (e.g. EN 14387 Type ABEK). Hand protection: Suitable chemical resistant safety gloves (EN 374) also with prolonged, direct contact (Recommended: Protective index 6, corresponding > 480 minutes of permeation time according to EN 374): E.g. nitrile rubber (0.4 mm), chloroprene rubber (0.5 mm), butyl rubber (0.7 mm) and other Manufacturer's directions for use should be observed because of great diversity of types. Eye protection: Tightly fitting safety goggles (splash goggles) (e.g. EN 166) Body protection: Body protection must be chosen based on level of activity and exposure. General safety and hygiene measures: Do not inhale gases/vapours/aerosols. Avoid contact with the skin, eyes and clothing. Handle in accordance with good building materials hygiene and safety practice. When using, do not eat, drink or smoke. Hands and/or face should be washed before breaks and at the end of the shift. At the end of the shift the skin should be cleaned and skin-care agents applied. Gloves must be inspected regularly and prior to each use. Replace if necessary (e.g. pinhole leaks). 9. Physical and Chemical Properties Form: liquid Colour: amber Odour: amine-like
Page: 5/9 BASF Safety data sheet Date / Revised: 17.10.2012 Version: 1.0 Product: MASTERFLOW 678 DP PLUS PTB pH value: > 12 (23 °C) Boiling point: No data available. Flash point: > 100 °C Flammability: does not ignite Lower explosion limit: No data available. Upper explosion limit: No data available. Self ignition: not self-igniting Self heating ability: It is not a substance capable of spontaneous heating. Explosion hazard: not explosive Fire promoting properties: not fire-propagating Vapour pressure: (20 °C) not applicable Density: 0.93 - 0.97 g/cm3 (23 °C) Bulk density: (20 °C) not applicable Solubility in water: insoluble Miscibility with water: (20 °C) immiscible Hygroscopy: Non-hygroscopic Viscosity, dynamic: Solids content: 100 % not applicable (30559173/SDS_GEN_AU/EN) Date of print 17.10.2012 Other Information: If necessary, information on other physical and chemical parameters is indicated in this section. 10. Stability and Reactivity Conditions to avoid: See MSDS section 7 - Handling and storage. Thermal decomposition: No decomposition if stored and handled as prescribed/indicated. Substances to avoid: zinc, aluminium, oxidizing agents, strong alkalies, acids
Page 1 and 2: Safety data sheet Page: 1/9 BASF Sa
Page 3: Page: 3/9 BASF Safety data sheet Da
Page 7 and 8: Page: 7/9 BASF Safety data sheet Da
Page 9: Page: 9/9 BASF Safety data sheet Da

Safety data sheet - BASF Construction Chemicals Pacific

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?