Soler & Palau - Tangra

More documents

Recommendations

Info

FDA Twin Fan FDA series are also available in twin fan version, with two double inlet fans mounted on the same shaft. To select for twin fans, use the curves of single fan with the following factors: FDA Series – Volume x 2 – Absorbed Power x 2.15 – Speed x 1.05 – Noise + 3 dB This series is available in Type S2, C2 or T2, fig. 2 shows the sizes and type available. Performances of twin fan series are not AMCA licensed. Type S2 Fan size 250 to 500 Volume 5.000 to 50.000 m 3 /h Type C2 Fan size 250 to 500 Volume 5.000 to 50.000 m 3 /h Type T2 Fan size 355 to 630 Volume 10.000 to 80.000 m 3 /h Wheel The wheel of FDA series has forward curved blades manufactured in galvanised sheet steel. Housing For all sizes, the housing is manufactured in galvanized sheet steel with the housing fixed to the side plates in “pittsburg lock” form system. Frame The frame is manufactured with galvanized angular bars for type “C”. For type “T” and “X”, they are manufactured with sections of steel and finished with polyester powder coating. Shaft Shafts are manufactured from C45 carbon steel using an automatic process for positioning and cutting of the keyways. All dimensional tolerances of the shaft are fully checked to ensure a precision fit and then coated with an anti-corrosion varnish after assembly. Technical specifications for information purposes only. Soler & Palau, S.A. reserves the right to change them without any previous notice. 5
Bearings FDA Series Bearings used are either deep groove ball bearing type with an eccentric locking collar or an adapter sleeve, or spherical roller bearings type sealed at both sides for different duty application as classified below: Mounted in a rubber housing Mounted on cast iron supports with grease point S C T X Fan Type SL Light Duty CL Light Duty TL Light Duty - Bearing Duty SM Medium Duty CM Medium Duty TM Medium Duty XM Medium Duty eg. Model FDA 450 C M TX Extra Heavy Duty XX Extra Heavy Duty Model FDA 450 C M Fan Bearing Duty (L, M, X) Fan type (S, C, T, X, Z) Fan Size (315, 355, 400,...1400) The bearings are lubricated for life and maintenance-free. If re-lubrication is necessary, it is recommended to use lithium base grease suitable for all temperatures within the operational limits. Accessories Casing Drain This option is available when using fans exposed to the atmosphere or operating in high humidity conditions. Guards Inlet guards, discharge guards and non-drive end shaft guards are available on request. Balancing Quality All wheels are statically and dynamically balanced to ISO1940 and AMCA 204 – G2.5 standards. Paintings Special powder-paint coatings of various thicknesses can be supplied on request. Outlet Flanges Outlet flanges are available upon request. Inspection Doors The inspection door can be supplied upon request. It can be supplied in one of the three position (P3, P4 & P5). Technical specifications for information purposes only. Soler & Palau, S.A. reserves the right to change them without any previous notice. 6
Page 1 and 2: Research Design and High Technology
Page 3 and 4: Introducción Introduction S&P - LA
Page 5: FDA Series Double Inlet Forward Cur
Page 9 and 10: Dynamic Pressure FDA Series The dyn
Page 11 and 12: FDA 160 FDA Series - Performance sh
Page 27 and 28: FDA 1000 FDA Series - Performance s
Page 29 and 30: FDA ‘C’ FDA 180-400 ‘C’ FDA
Page 31 and 32: FDA ‘X’ FDA 560-1000 ‘X’ FD
Page 33 and 34: FDA ‘C2’ FDA 250-400 ‘C2’ F
Page 35 and 36: Shaft FDA Series w t t1 z Ød-g6 ø
Page 37 and 38: Research Design and High Technology
Page 39 and 40: Introducción Introduction S&P - LA
Page 41 and 42: BDB Series Double Inlet Centrifugal
Page 43 and 44: Shaft BDB Series Shafts are manufac
Page 45 and 46: Example of Selection BDB Series BDB
Page 47 and 48: BDB 355 BDB Series Type S-C T X M
Page 49 and 50: BDB 450 BDB Series Type M. kW M. r
Page 51 and 52: BDB 560 BDB Series Type S-C M. kW 1
Page 53 and 54: BDB 710 BDB Series Type S-C M. kW 1
Page 55 and 56: BDB 900 BDB Series Type T M. kW 30
Page 57 and 58:
BDB 1120 BDB Series Type M. kW M. r
Page 59 and 60:
BDB 1400 BDB Series - Performance s
Page 61 and 62:
BDB ‘C’ BDB 315-400 ‘C’ BDB
Page 63 and 64:
BDB ‘T’ BDB 1120-1400 ‘T’ B
Page 65 and 66:
BDB ‘X’ BDB 1120-1400 ‘XX’
Page 67 and 68:
BDB ‘C2’ BDB 315-400 ‘C2M’
Page 69 and 70:
Shaft BDB Series w t t1 z Ød-h7 ø
Page 71 and 72:
Research Design and High Technology
Page 73 and 74:
Introducción Introduction S&P - LA
Page 75 and 76:
BSB Series Single Inlet Centrifugal
Page 77 and 78:
BSB Series The bearings are lubrica
Page 79 and 80:
Dynamic Pressure BSB Series The dyn
Page 81 and 82:
BSB 315 BSB Series Pt [Pa] 6000 500
Page 83 and 84:
BSB 400 BSB Series - Performance sh
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
BSB 1000 BSB Series - Performance s
Page 93 and 94:
BSB 1250 BSB Series - Performance s
Page 95 and 96:
BSB ‘C’ BSB 315-400 ‘C’ BSB
Page 97 and 98:
BSB ‘T’ BSB 1120-1400 ‘T’ B
Page 99 and 100:
BSB ‘X’ BSB 1120-1400 ‘X’ B
Page 101 and 102:
BSB ‘UI’ BSB 1120-1400 ‘UI’
Page 103 and 104:
BSB ‘UII’ BSB 1120-1400 ‘UII
Page 105 and 106:
Operational Limits - “BSB” BSB
show all

Soler & Palau - Tangra

Create successful ePaper yourself

Delete template?

Save as template?