AIR HOSES

More documents

Recommendations

Info

SPECIAL HARDWARE BLOW GUNS READY JET ® INLINE BLOW GUN “Handiest tool in the shop - always there, ready to use.” USING OUR READY JETS Ready Jets fit permanently between the air hose and the coupler. The Ready Jet Inline Blow gun is a sealed unit and is virtually trouble free. The button is brass for a quality product. The valve seal is a neoprene o-ring which is impervious to water, oil, etc. THE STAR TIP BLOW GUN A variable-flow blow gun featuring a nozzle that complies with OSHA requirements. ‘‘Star-tip’’ nozzle offers many safety features not found in other blow gun tips: ● Ultra slim nozzle reduces noise level. ● Thinner tip, along with a special bent tube, for hard-to-reach places. ● ‘‘Star-tip’’ design allows full air flow through six separate outlets and still complies with OSHA requirements. Reduces noise levels when used with compressed air. INLINE BLOW GUN READY JET ® READY TO USE ● Save time, energy, & money. ● Always there, ready to use. ● Small, compact, & handy. ● Fits permanently between air hose & coupler. ● Never gets lost or misplaced. ● Natural angle for easy use. ● Durable and weighs only 2 oz.’s ● Precision machined for a quality tool. ● Deliver more air. ● Made in America. ● Female 1/4 NPT. ● Made of aircraft aluminum for toughness and light weight. ● Accepts 1/4” MPT fittings. MADE IN USA New ‘‘star-tip’’ nozzle is a powerful, yet quiet, performer. ● Built-in silencer tip ensures low noise level, 79 dBA. ● Low air consumption, 5 CFM. ● Unique valve design allows a fully variable flow. ● Comfortable handling by using latest ergonomic design. ● High tensile materials for tough handling. Part No. 113772 Part No. 113773 Six outlet tip offers an even distribution of air. PINPOINT AIR CONCENTRATOR TIP Mount on STAR TIP BLOW GUN for concentrated, direct, pinpoint air flow for cleaning carburetor passages, orifices, pressurizing transmission valve bodies, etc. RUBBER TIPPED INLINE BLOW GUN ● Non-scratch tip. ● Inlet and outlet pressure the same. ● To meet OSHA requirements airline pressure must be reduced to 30 psi. REPLACEMENT RUBBER TIP Part No. 113740 Part No. 113742 SAFETY INLINE BLOW GUN ● Meets OSHA requirements with special relief hole in nozzle which limits pressure to 30 psi when dead ended and used on air line of 150 psi or less. REPLACEMENT SAFETY TIP Part No. 113741 B11-4 REVISED DECEMBER, 2004 Part No. 113743 © Copyright 2008. All rights reserved. No portion may be copied or reproduced in any manner.
SPECIAL HARDWARE AIR TOOLS / AIR-LINE COUPLERS & PLUGS HOW TO IDENTIFY INTERCHANGE DESIGNS Interchangeability of pneumatic couplings is determined by NIPPLE DESIGN. Learn to identify the basic nipple types and coupler and nipple interchange will become easy. There are SEVEN different designs currently used in the automotive market. Four of these seven cover 97% of all quick couplings used today. We provides complete interchange to the four primary designs. The three designs NOT covered are shown at the bottom of the page. INDUSTRIAL / MILTON DESIGN This design has been adopted by many coupler manufacturers, including Milton, Hansen, Aro, Lincoln, and Schrader. It will work with either “sleeve” type or “push” type couplers. No matter what the coupler looks like, if it mates with this nipple, it is an “Industrial / Milton Interchange” design. It can be identified by its 3/16” pilot and its flat-bottomed, “V”-shaped ball groove. TRU-FLATE DESIGN This design is easily recognized because it has the shortest nipple pilot in the industry; however, it has the widest metal section between the ball groove and the pilot. In addition, the sealing surface on the end of the nipple is wider than other “interchange” designs. This design provides better sealing characteristics and longer seal life. ARO DESIGN This design is characteristic of the Aro-210 series, and requires a coupler of proper matching design. Although similar in appearance to the “Industrial / Milton Interchange” design, it can be easily distinguished because its pilot is 1/8” longer and its ball groove is nearly round. LINCOLN DESIGN The “Lincoln Long-Stem” design is the most easily identified design. The long 3/4” pilot is so distinctive it cannot be confused with the other designs. It will only mate with couplers of matching design. OTHER DESIGNS SCHRADER DIAMOND “U” GRACO STANDARD HOW TO INTERCHANGE COUPLERS AND NIPPLES 1. The Design Selection Like name designs, no matter which manufacturer, are inter-changeable. NOTE: One DESIGN will NOT interchange with another design. 2. The Size Selection There are three BODY SERIES sizes— Standard 1/4” and Heavy Duty 3/8” and 1/2”. To interchange, the coupler and nipple must have the same body size. 3. Thread Size To check size of pipe thread fittings, refer to catalog page B13-2. © Copyright 2008. All rights reserved. No portion may be copied or reproduced in any manner. HOW TO DETERMINE BODY SIZE/ COUPLER SIZE/BASIC SIZE Coupler size is important, since too small a coupling can act as a restriction in the air line, reducing both the pressure and volume of air reaching the end of the hose. It is generally recommended that the body size of the coupler be matched to the I.D. of the hose being used. Thus 1/4” I.D. hose should be fitted with 1/4” I.D. couplings. Generally speaking, 3/16” I.D. hose should be fitted with 1/4” couplings, while 5/16” I.D. hose may be fitted with either 1/4” or 3/8” couplings, depending on the volume and pressure required at the end of the hose. 1/2” I.D. hose should be fitted with 1/2” couplings. ● Maximum Inlet Pressure: 300PSI ● Maximum Temperature: 250°F WARNING: COUPLERS IN THIS SECTION ARE FOR USE WITH SHOP AIR ONLY. MILTON M-STYLE INDUSTRIAL INTERCHANGE SERIES 1/4” BASIC SIZE Milton M-style “kwik-change” couplers and plugs will interchange with all manufacturers who comply with the dimensional requirements of military specification MIL-C-4109. ● Coupler bodies are brass with brass sleeves. ● Plugs are case hardened steel plated to resist rust. ● Air flow: 40 SCFM Female Coupler Steel Sleeve w/Drag Guard Male Coupler Male Coupler Female Plug Male Plug Male Plug MILTON P-STYLE TRU-FLATE/PARKER INTERCHANGE SERIES 3/8” BASIC SIZE ● Coupler bodies are heavy duty steel. ● Plugs are case hardened steel plated to resist rust. ● Bodies have 8 locking balls. ● Air flow: 68 SCFM Female Coupler ● Seals: Buna-N COUPLERS PLUGS PART PART CONNECTION NUMBER NUMBER 1/4 NPT Female 100715 5 100728 10 1/4 NPT Male 100716 5 100727 10 STEEL SLEEVE w/DRAG GUARD PART CONNECTION NUMBER 1/4 NPT Female 100755 5 Female Plug COUPLERS PLUGS PART PART CONNECTION NUMBER NUMBER 1/4 NPT Female 101803 5 101810 10 1/4 NPT Male 101804 5 101809 10 3/8 NPT Female 101805 5 101808 10 3/8 NPT Male - - - - 101807 10 B11-5 REVISED FEBRUARY, 2007
Page 1 and 2: SPECIAL HARDWARE AIR HOSES PERMA HO
Page 3: NOTE: See page G16-46 & 47 for addi
Page 7 and 8: SPECIAL HARDWARE AIR-LINE COUPLERS
Page 9 and 10: SPECIAL HARDWARE AIR-LINE / HYDRAUL

AIR HOSES

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?