Specifications & External Dimensions

MULTIPLE SPLIT TYPE AIR CONDITIONERS
Series
CM05EU4-E

High COP (energy consumption efficiency)
Achieved Top class in the Industry
Comparison of COP (energy consumption efficiency)
COP
4.0
3.5
3.0
2.5
2.0
0
2.58
50%
Energy
saving
Our equivalent
product 10 years
before
3.39
CITY MULTI
14.5%
Energy
saving
3.88
Comparing to the current energy
saving type,
COP upgraded by about 15%!
Comparing to our equivalent product
10 years before,
COP upgraded by about 50%!
(10HP equivalent model)
Inverter driven outdoor fan motor
newly employed!
R410A highly efficient inverter
compressor employed!
• Improvement of
heat exchanger performance
• Newly designed refrigerant circuit
(low pressure loss)
Resulting in Total Energy
Conservation
Heating operation range covers an outdoor
temperature of down to -20˚C (wet bulb temperature)
Operating range in
cooling is from an
outdoor temperature
of -5˚C, while that in
heating has
expanded to an
outdoor temperature
of -20˚C!
The operation range
can now cover even
cold regions.
✻ -12˚C~15˚C for
PUMY series.
-20˚C
✻
Operable even in
very cold regions
Outdoor temperature
(wet bulb temperature)
Under cooling
-5˚C
Under heating
15.5˚C
Outdoor temperature
(dry bulb temperature)
-20 -10 0 10 20 30 40
✻
43˚C

High static pressure of 60Pa
achieved, the industry top class*
Flexibility in air conditioning design has been enlarged with a high static
pressure of 60Pa.
(except PUMY series)
*Optional parts
Facilitated connection
of supply hood
Outdoor unit packing
without using wooden materials
The use of wooden frame for the transport of the outdoor unit has been discontinued. The structure is so designed that the unit can be
transported with a forklift not using wooden frames or pallets. This contributes in reducing waste and preserving the global environment.
Eliminating wood consumption
thanks to the wooden packing
discontinued.
Transportable by a forklift
without using pallets.
Night Mode Quiet
operation can reduce
sound level of 8dB!
(10HP)
CITYMULTI Series Night mode quiet
operation can reduce sound level by
sensing ambient temperature condition.
57dB
49dB
(10HP)
above
30˚C
below
30˚C
Front and rear double
suction structure
The front and rear double suction structure
provides the smooth airflow to reduce the
pressure loss, which results in low noise.
Air passage and machine
compartment separated
The machine compartment is sealed up to
attain the low noise level in all directions.
(except PUMY series)
“All
Directions”
*Needs to set night mode setting at the site.
*Night mode could be turn off automatically due to ambient
temperature and required capacity load condition.

Series provide
for air conditioning comfort with
MITSUBISHI ELECTRIC's
leading edge technologies.
Less cold draught,
More comfort
Only with
MITSUBISHI
ELECTRIC
CITYMULTI Series can change the target evaporating
temperature during cooling mode.
Unit with higher off coil temperature can offer more comfort due
less chance of cold draughts.
Conventional Model CITYMULTI Series
Cooling Operation
Set Temperature
of 14˚C
(except PUMY series)
By selecting a dip switch on the
unit, a cooling operation set
temperature of 14˚C is possible on
the floor standing and ceiling
concealed models. Suitable for
lower set temperature applications
like Gymnasiums etc,,,.
Only with
MITSUBISHI
ELECTRIC

High-capacity
reluctance DC motor
drive compressor
Motor efficiency greatly improved +
Reduced suction refrigerant heating loss
Anti-Corrosion
Blue Fin as a
Standard!
CITYMULTI Series will
have an Anti-Corrosion heat
exchanger (Blue Fin) as a
standard.
Industry Top class
Low Noise Design
New Fan Design
City Multi Y/R2 VRF systems led the introduction of larger single fan rotors
some ten years ago and achieved substantially lower noise levels over
multiple designs. Continuing development in the areas of blade shape and
weight has achieved higher performance and lower noise level.
Conventional model fan
New model fan

Mitsubishi Electric
City Multi
Series
– towards a new era of
highly advanced air conditioning –
As a market leading company,
Mitsubishi Electric offers the
"State of the Art" City Multi
VRF
system, adopting
advanced refrigeration & control
technology, thereby achieving
high performance and ultimate
design flexibility.
1

Series Product Lineup
New
Outdoor Unit
Air Cooled System
4HP 5HP 6HP 8HP 10HP 12HP 14HP 16HP 18HP 20HP 22HP 24HP 26HP
Heat Pump
Heat Recovery
28HP 30HP 32HP 34HP 36HP 38HP 40HP 42HP 44HP 46HP 48HP 50HP
Heat Pump
Water Cooled System
8HP 10HP 16HP 20HP
Heat Pump
Heat Recovery
PLFY-P VCM-E/VAM-E
........p.27, 28 / 41, 42
Indoor Unit
PEFY-P VMH-E
........p.35 / 51, 52
PLFY-P VLMD-E
........p.29 / 43, 44
PMFY-P VBM-E
........p.30 / 45
PEFY-P VMR-E-L/R
New ........p.31 / 46
New
PEFY-P VMS-E
........p.32 / 47
PEFY-P VML-E
........p.33 / 48
New
PCFY-P VGM-E
........p.36 / 53
PKFY-P VAM-E/VGM-E
/VFM-E
........p.37 / 54, 55
PFFY-P VKM-E
........p.38 / 56
PFFY-P VLEM-E/VLRM-E
........p.39 / 57, 58
PEFY-P VMM-E
........p.34 / 49, 50
PEFY-P VMH-E-F
........p.40 / 59, 60
Lossnay/OA Processing Units
Air Conditioning MANAGEMENT SYSTEM
2

FEATURES
Effective space utilization thanks to a
small installation space.
The installation space of the outdoor unit has
greatly been reduced. The reduction counts for
about 33%* maximum comparing to our
conventional CITY MULTI Series.*24·26HP outdoor units
conventional CITY MULTI
24
26
2990
450
840
840
450 450 33%
1990
HP
5.20m 2 3.46m 2
450
reduction
Effective utilization of vacant spaces
The compact design
and isolated installation
of each unit allow
utilization of vacant
spaces effectively.
Easy installation
even in a
narrow space
Outdoor unit installation space (including service space)
*Image of 28~32HP system
4~6HP 8~14HP 16HP 18~26HP 28~32HP 34~50HP NEW
1unit
1unit
1unit
1unit
2units
2units
Installation Space Air Cooled
630
10 950 10
150
330
150
1740
990
450
840
450
1740
1290
450
840
450
0.61m 2 1.72m 2 2.24m 2 3.46m 2 3.74(4.14)m 2
1740
1990
450
840
450
1390
(1540)
10 990 1690
2690
100
(250)
840
450
10
1990 1990
450
840
450
6.94m 2
8HP
WY Series (Heat Pump)
WR2 Series (Heat Recovery)
10HP 16HP 20HP 8HP 10HP 16HP 20HP
Water Cooled
Installation Space
(upside piping)
550
450
550
450
550
450
990
1,980
990
1,980
0.99m 2 1.98m 2 0.99m 2 1.98m 2
550
450
3
Easy carrying-in by single package design
Reduced carrying-in process thanks to the single package configuration
For lifting up to building rooftop with a crane
For field
combining type
As the lifting up and
down operation is
repeated frequently, the
installation work longer.
One
shot
The CITY MULTI
(4~26HP) can be
delivered in one go,
thus allowing far
speedier installation.

The World's First and Only "2-Pipe" Heat Recovery System
The Innovative BC Controller Which Makes a 2-pipe System Possible
BC Controller Operation
R2 WR2
Operation primarily for cooling
Operation primarily for cooling
Outdoor unit BC controller
Switching valve Indoor unit
4-way valve Check valve
High
pressure
gas
Heat
exchanger
Compressor
Low pressure gas
Low pressure pipe
High
pressure gas
Fan Gas/liquid
separator
High pressure 2-phase
High pressure pipe
LEV
Low pressure 2-phase
High pressure liquid
Cooling
Cooling
Cooling
Heating
Total heat recovery operation
Total heat recovery operation
Low pressure gas
High pressure gas
Low pressure gas
Low pressure 2-phase
High pressure liquid
High pressure 2-phase
Low pressure gas
High
pressure gas
High
pressure gas
Heating
Heating
Low pressure gas
Cooling
Cooling
Low pressure gas Low pressure 2-phase
High pressure liquid
R2 WR2
Achieving smallest number
of pipework connection
thanks to 2-pipe system
Comparison of piping connection =2 connections =3 connections
City Multi R2/WR2 Total number of connections
20
Outdoor unit
BC Controller
Heat Recovery System can
create maximum of 15HP
capacity from 10HP unit!
The waste heat recovery system in the refrigerant system increases the energysaving
effect as the cooling and heating simultaneous operation is carried out.
Indoor unit output
A Heating 10HP, Cooling 5HP, Total 15HP
B Heating 7.5HP, Cooling 7.5HP, Total 15HP
Cooling 10HP
C Cooling capacity of each indoor
unit is approx. 10/15 of the rating.
( )
R2 WR2
Outdoor unit
input
10HP Cooling 5HP: Waste heat utilized
7.5HP Optimum operation pattern
In the same mode, the
10HP compressor capacity is the
maximum output
(in this case 10HP).
Indoor unit
Operation pattern of
New City Multi R2 System
15HP
( )
Total 15HP indoor
unit is connected with
10HP outdoor unit.
The total number of connections for City Multi R2 is only
68 when the 16 indoor units are installed.
3-pipe type
Outdoor unit
Branch unit
Indoor unit
Number of branches
4
10
16
2-pipe type
20
44
68
Total number of connections
58
3-pipe type
58
154
–
The more frequently cooling and heating simultaneous
operation is carried out, the higher the energy-saving effect is.
COP in heat recovery operation
Energy consumption efficiency (COP)
8
7
6
5
4
3
2
1
0
Heating indoor unit
Cooling and heating
simultaneous and primarily
cooling operation
10HP
7.5HP
5HP
A Primarily heating operation
5HP 7.5HP 10HP
Cooling indoor unit
Cooling and heating balance operation
Cooling and heating
simultaneous and primarily
heating operation
Cooling and heating non-simultaneous model
B Total heat recovery operation
15HP
20 40 60 80 100 Heating
ratio
C
R2 WR2
4

FEATURES
Downsizing of refrigerant
piping connections
By making the connection diameter of refrigerant piping
(10HP system)
smaller, the piping space can be minimized, and the ease of field
installation. Workability upgraded and the piping materials reduced.
Comparison of piping size (for 10HP system) List of major piping sizes
Conventional type
Gas
piping
φ28.58
Liquid
piping
φ12.7
CITY MULTI
type
Gas
piping
φ22.2
Liquid
piping
φ9.52
System capacity
4~6HP system
8HP system
10/12HP system
14HP system
16HP system
18~26HP system
28~32HP system
34~50HP system
Gas piping : downed by 2 sizes
Liquid piping : downed by 1 size
Significant reduction of field piping connections
The single package design eliminates the oil equalizing pipe and
the piping between outdoor units, thus upgrading the reliability,
reducing complexity and reducing the installation cost.
Liquid piping
φ9.52
φ12.7
φ15.88
φ19.05
Gas piping
φ15.88
φ19.05
φ22.2
φ28.58
φ34.93
φ41.28
Eliminating the
oil equalizing pipe
(8~32HP)
4~14HP 16HP 18~26HP 28~32HP 34~50HP NEW
Oil equalizing
pipe not
required
Liquid piping
Gas
piping
Piping between
units not
required
Liquid
piping
Gas piping
Gas piping
Liquid
piping
Oil equalizing
pipe not
required
Oil equalizing
piping
Liquid
piping
Gas
piping
Connection spot : 2
Connection spot : 6 Connection spot : 12
*The actual product may differ from the photo.
Upgrading reliability by minimizing the number
of parts and providing back up function
18~26HP 28~32HP 34~50HP NEW
In case of one
compressor fails,
In case of one
compressor fails,
Alternate
operation
Facilitating
maintenance work by
minimizing the number
of parts, and
upgrading reliability by
simplifying
construction designed
Compressor
Compressor
Compressor
backup operation
Compressor
Compressor
Compressor
backup operation
Backup
operation
In case of
malfunction
mulfunction
5

Realizing refrigerant piping total length of
400m* top class in industry *CITY MULTI R2 Series
S Series (4~6HP)
Refrigerant Piping Restrictions
Total length........................................................
Furthest length..................................................
Furthest length after first branch.......................
Top-bottom differentials between units
Between indoor unit and outdoor unit
(outdoor unit is upper)......................................
Between indoor unit and outdoor unit
(outdoor unit is lower)........................................
Between indoor units.........................................
120m or less
80m or less
30m or less
30m or less
20m or less
12m or less
Y Series (8~32HP)
Refrigerant Piping Restrictions
Total length........................................................
Furthest length..................................................
Furthest length [equivalent length]...................
Furthest length after first branch.......................
Top-bottom differentials between units
Between indoor unit and outdoor unit
(outdoor unit is upper)......................................
300m or less
150m or less
175m or less
40m or less
50m or less
Between indoor unit and outdoor unit
(outdoor unit is lower)........................................ 40m or less*
Between indoor units......................................... 15m or less
* 4m or less in cooling at outdoor temperature 0˚C or lower.
Y Series (34~50HP)
Refrigerant Piping Restrictions
Total length........................................................
Furthest length..................................................
Furthest length [equivalent length]...................
Furthest length after first branch.......................
Between Main and Sub outdoor unit.................
Top-bottom differentials between units
Between indoor unit and outdoor unit
(outdoor unit is upper)......................................
300m or less
150m or less
175m or less
40m or less
4m or less
50m or less
Between indoor unit and outdoor unit
(outdoor unit is lower)........................................ 40m or less*
Between indoor units......................................... 15m or less
Between Main and Sub outdoor unit................. 0.1m or less
* 4m or less in cooling at outdoor temperature 0˚C or lower.
Y Series
Top-bottom differential 50m
Indoor unit
Top-bottom differential 50m
Outdoor unit
Furthest piping length
175m (equivalent length)
(actual length 150m)
between indoor units
top-bottom differential
15m
Outdoor unit
Furthest piping length
175m (equivalent length)
(actual length 150m)
Indoor unit
between indoor units
top-bottom differential
15m
6

FEATURES
Realizing refrigerant piping total length of
400m* top class in industry *CITY MULTI R2 Series
R2 Series (P200, P250, P300, P350 type)
Refrigerant Piping Restrictions
Total length............................................................ 300m or less (400m) *2
Furthest length...................................................... 150m or less
Furthest length [equivalent length]........................ 175m or less
Difference between outdoor unit and
BC controller unit................................................... 110m or less
Difference between BC controller
main-unit and furthest indoor unit....................... 40m or less *3
Top-bottom differentials between units
Between indoor unit and outdoor unit (outdoor unit is upper).... 50m or less
Between indoor unit and outdoor unit (outdoor unit is lower)..... 40m or less
Between indoor unit and BC controller................... 15m or less (10m) *1
Between indoor units............................................. 15m or less (10m) *1
*1. Value in ( ) is applied to the P200/P250 type indoor unit.
*2. Please refer to 'refrigerant piping limits' (see the figure) in case of the total length is greater than 300m.
*3. Please refer to 'Limits between BC controller - indoor unit' (see the figure) in case of the piping length between
BC controller and furthest indoor unit is greater than 40m (except P250 indoor unit).
*4. Do not use joint or header for P200/P250 type indoor unit.
*5. Do not connect P200/P250 type indoor unit with the indoor unit of any other capacity at a same branch port.
R2 Series
P200, P250, P300, P350 types
Difference of
height 50m
Between indoor unit and
BC controller topbottom
differential 15m
Between indoor unit and
BC controller
top-bottom differential 15m
Outdoor unit
Furthest piping length
175m (equivalent length)
(actual length 150m)
Between indoor units
top-bottom
differential 15m
R2 Series (P200 ~ P650 type)
Refrigerant Piping Restrictions
Total length............................................................ 300m or less (400m) *1
Furthest length...................................................... 150m or less
Furthest length [equivalent length]........................ 175m or less
Difference between outdoor unit and
BC controller main-unit.......................................... 110m or less
Difference between BC controller
main-unit and furthest indoor unit.......................... 40m or less *2
Top-bottom differentials between units
Between indoor unit and outdoor unit [outdoor unit is upper].... 50m or less
Between indoor unit and outdoor unit [outdoor unit is lower]..... 40m or less
Between indoor unit and BC controller................... 15m or less
Between indoor units............................................. 15m or less (10m)*3
Between BC controller main-unit and sub-unit.............. 15m or less
Between indoor unit (BC controller main-unit)
and indoor unit (BC controller sub-unit)....................... 15m or less (10m)*3
* If indoor units (over 16 branches) are connected, two BC controller units are required and there must be three pipes
between BC controllers.
*1. Please refer to 'refrigerant piping limits' (see the figure) in case of the total length is greater than 300m.
*2. Please refer to 'Limits between BC controller - indoor unit' (see the figure) in case of the piping length between
BC controller and furthest indoor unit is greater than 40m (except P250 indoor unit).
*3. Value in ( ) is applied to the P200/P250 type indoor unit.
*4. Do not use joint or header for P200/P250 type indoor unit.
R2 Series
P200 ~ P650 types
Top-bottom
differential 50m
Between indoor unit and
BC controller topbottom
differential 15m
Between indoor unit and
BC controller
top-bottom differential 15m
Outdoor unit
Furthest piping length
175 m (equivalent length)
(actual length 150 m)
Between indoor units
top-bottom
differential 15m
In case of a BC controller unit
(16 branches or less)
• Refrigerant Piping Limits
400
Main pipe and
branch pipe: 2-pipe
Outdoor unit
Piping total lenght (m)
350
300
250
200
30 40 50 60 70 80 90 100 110
Distance between outdoor unit and BC Controller (m)
• Limits between BC contoller - indoor unit
Distance between BC controller (Main) -
furthest indoor unit (m)
70
60
50
40
30
20
10
0
0 5 10 15
Height differential between BC controller (Main) - furthest indoor unit (m)
Top-bottom
differential
50m or less
Between indoor
units
topbottom
differential
15m or less
Distribution sub-control
Maximum length between indoor unit and
BC controller 40 m or less (2-pipe)
Distribution
control
main-unit
In case of two BC controller units
(Over 16 branches)
110 m or less between outdoor
unit and BC controller (2-pipe)
Three pipes between
BC controllers
Between distribution
controls top-bottom
differential 15m or less
7

Series Product Lineup
Wide variation of outdoor unit to adapt with various applications.
Series
S Series
Type
A
Heat Pump
4HP
PUMY-P100YHM
PUMY-P100VHM
5HP
PUMY-P125YHM
PUMY-P125VHM
6HP
PUMY-P140YHM
PUMY-P140VHM
Series Type
Y Series A
Heat Pump
Cooling Only
R2 Series A Heat Recovery
8HP
PUHY-P200YGM-A
PUY-P200YGM-A
PURY-P200YGM-A
10HP
PUHY-P250YGM-A
PUY-P250YGM-A
PURY-P250YGM-A
12HP
PUHY-P300YGM-A
PUY-P300YGM-A
PURY-P300YGM-A
14HP
PUHY-P350YGM-A
PUY-P350YGM-A
PURY-P350YGM-A
16HP
PUHY-P400YGM-A
–
PURY-P400YGM-A
Series
Y Series
R2 Series
Type
A
A
Heat Pump
Heat Recovery
18HP 20HP 22HP
PUHY-P450YGM-A PUHY-P500YGM-A PUHY-P550YGM-A
PURY-P450YGM-A PURY-P500YGM-A PURY-P550YGM-A
24HP
PUHY-P600YGM-A
PURY-P600YGM-A
26HP
PUHY-P650YGM-A
PURY-P650YGM-A
Series
Y Series
Type
A
28HP 30HP 32HP
Heat Pump PUHY-P700YSGM-A PUHY-P750YSGM-A PUHY-P800YSGM-A
Series
Y Series
Type
A
Heat Pump
34HP
PUHY-P850YSGM-A
36HP
PUHY-P900YSGM-A
38HP 40HP 42HP 44HP 46HP 48HP 50HP
PUHY-P950YSGM-A PUHY-P1000YSGM-A PUHY-P1050YSGM-A PUHY-P1100YSGM-A PUHY-P1150YSGM-A PUHY-P1200YSGM-A PUHY-P1250YSGM-A
Series Type
WY Series W
WR2 Series W
Heat Pump
Heat Recovery
8HP 10HP 16HP 20HP
PQHY-P200YGM-A PQHY-P250YGM-A PQHY-P400YSGM-A PQHY-P500YSGM-A
PQRY-P200YGM-A PQRY-P250YGM-A PQRY-P400YSGM-A PQRY-P500YSGM-A
Type: A =Air Cooled.
W=Water Cooled.
8

OUTDOOR UNIT
Specifications & External Dimensions
New
S SERIES
R410A
Specifications
Model name
Power source
PUMY-P100YHM PUMY-P125YHM
3-phase, 380-400-415V, 50Hz
PUMY-P140YHM
Cooling capacity
(Nominal)
Power input
Current input
COP
*1
*1
*1
*2
kW
kcal / h
Btu / h
kcal / h
kW
A
11.2
9,600
38,200
-
3.30
5.28-5.02-4.84
3.39
14.0
12,000
47,800
12,500
4.27
6.83-6.49-6.26
3.28
15.5
13,300
52,900
14,000
5.32
8.51-8.09-7.80
2.91
Temp. range of
cooling
Heating capacity
(Nominal )
Power input
Current input
COP
Temp. range of Indoor temp.
Heating Outdoor temp.
Indoor unit Total capacity
connectable Model / Quantity
Noise level (measured in anechoic room)
Diameter of Liquid
refrigerant pipe Gas
External finish
External dimension H ✕ W ✕ D
Net weight
Heat exchanger
Compressor Type
Maker
Starting method
Motor output
Case heater
Standard
attachment
Optional parts
Remark
Indoor
Outdoor
*3
*3
*3
W.B.
D.B.
kW
kcal / h
Btu / h
kW
A
D.B.
W.B.
dB
mm(in.)
mm(in.)
mm
kg
kW
kW
Lubricant ✕ original charge
FAN
Air flow rate m 3 / min
External static press.
Type ✕ Quantity
Control, Driving mechanism
Motor output kW
HIC circuit (HIC: Heat Inter-Changer)
Protection High pressure protection
Inverter circuit (COMP. / FAN)
Compressor
Fan motor
Defrosting method
Refrigerant Type x original charge
Control
Document
Accessory
12.5
10,800
42,700
3.63
5.81-5.52-5.32
3.44
P20 ~ P125 / 1 ~ 6
49/51
Note:
*1 Nominal cooling conditions
Indoor: 27˚CDB/19˚CWB (81˚FDB/66˚FWB)
Outdoor 35˚CDB (95˚FDB)
Pipe length: 7.5m (24-9/16ft)
Level difference: 0m (0ft)
* Nominal condition *1, *3 are subject to JIS B8615-1
* Due to continuing improvement, above specifications may be subject to change without notice.
1.9
-
15 ~ 24˚C (59~75˚F)
- 5 ~ 46˚C (23~115˚F)
10 to 46˚C D.B.(50 to 115˚FD.B.) : in case of connecting PKFY-P20/P25 type indoor unit.
16.0
13,800
54,600
4.29
6.87-6.52-6.29
3.73
15~27˚C (59~81˚F)
-12~15˚C (10~59˚F)
50 ~ 130% of outdoor unit capacity
P20 ~ P140 / 1 ~ 8
50/52
φ9.52 (φ3/8" ) Flare
φ15.88 (φ5/38" ) Flare
Galvanized steel sheet
1,350 ✕ 950 ✕ 330
140
Salt-resistant cross fin & copper tube
Inverter scroll hermetic compressor
Mitsubishi Electric Corporation
Inverter
2.4
-
MEL56 x 2.3 L
100
0 Pa
Propeller fan ✕ 2
DC-control, Direct-driven by motor
0.06 x 2
-
High pressure sensor, High pressure switch 4.15 MPa
Over-heat protection, Over-current protection
Discharge thermo protection, Over-current protection
Over-heat protection, Voltage protection
Auto-defrost mode (Reversed refrigerant circle)
R410A ✕ 8.5kg ( 19 lb)
LEV circuit
Installation Manual
Grounded lead wire ✕ 2
Joint: CMY-Y62G-F ; Header:CMY-Y64/68G-F
18.0
15,500
61,400
5.32
8.51-8.09-7.80
3.38
P20 ~ P140 / 1 ~ 8
51/53
Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be referred to the Installation Manual.
*2 Nominal cooling conditions
*3 Nominal heating conditions
27˚CDB/19.5˚CWB (81˚FDB/67˚FWB) 20˚CDB (68˚FDB)
35˚CDB (95˚FDB)
7˚CDB/6˚CWB
5m (16-3/8ft)
7.5m (24-9/16ft)
0m (0ft)
0m (0ft)
2.9
-
Unit converter
kcal= kW ✕ 860
Btu/h= kW ✕ 3,412
cfm= m 3 /min ✕ 35.31
lb= kg/0.4536
* The specification data is subject to rounding variation.
9

OUTDOOR UNIT
Specifications & External Dimensions
New
Model name
Power source
Cooling capacity
(Nominal)
Power input
Current input
COP
Temp. range of Indoor
cooling Outdoor
Heating capacity
(Nominal )
S SERIES
R410A
Power input
Current input
COP
Temp. range of Indoor temp.
Heating Outdoor temp.
Indoor unit Total capacity
connectable Model / Quantity
Noise level (measured in anechoic room)
Diameter of Liquid
refrigerant pipe Gas
External finish
External dimension H ✕ W ✕ D
Net weight
Heat exchanger
Compressor Type
Maker
Starting method
Motor output
Case heater
Standard
attachment
Optional parts
Remark
*1
*1
*1
*2
*3
*3
*3
kW
kcal / h
Btu / h
kcal / h
kW
A
W.B.
D.B.
kW
kcal / h
Btu / h
kW
A
D.B.
W.B.
dB
mm(in.)
mm(in.)
mm
kg
kW
kW
Lubricant ✕ original charge
FAN
Air flow rate m 3 / min
External static press.
Type ✕ Quantity
Control, Driving mechanism
Motor output kW
HIC circuit (HIC: Heat Inter-Changer)
Protection High pressure protection
Inverter circuit (COMP. / FAN)
Compressor
Fan motor
Defrosting method
Refrigerant Type x original charge
Control
Document
Accessory
Note:
*1 Nominal cooling conditions
Indoor: 27˚CDB/19˚CWB
Outdoor 35˚CDB
Pipe length: 10m
Level difference: 0m (0ft)
* Nominal condition *1, *3 are subject to JIS B8615-1
* Due to continuing improvement, above specifications may be subject to change without notice.
Specifications
PUMY-P100VHM
PUMY-P125VHM
PUMY-P140VHM
11.2
9,600
38,200
10,000
3.34
1-phase, 220-230-240V, 50Hz 220V,60Hz
14.0
12,000
47,800
12,500
4.32
15.5
13,300
52,900
14,000
5.35
15.4/14.8/14.1 15.4
20.0/19.1/18.3 20.0
24.7/23.6/22.7 24.7
3.35
12.5
10,800
42,700
3.66
16.9/16.2/15.5 16.9
3.24
15 ~ 24˚C (59~75˚F)
- 5 ~ 46˚C (23~115˚F)
10 to 46˚C D.B.(50 to 115˚FD.B.) : in case of connecting PKFY-P20/P25 type indoor unit.
16.0
13,800
54,600
4.33
20.0/19.1/18.3 20.0
2.90
18.0
15,500
61,400
5.58
25.8/24.7/23.6 25.8
3.42
P20 ~ P125 / 1 ~ 6
49/51
2.2
-
3.69
15~27˚C (59~81˚F)
-12~15˚C (10~59˚F)
50 ~ 130% of outdoor unit capacity
P20 ~ P140 / 1 ~ 8
50/52
φ9.52 (φ3/8" ) Liquid
φ15.88 (φ5/38" ) Gas
Galvanized steel sheet
1,350 ✕ 950 ✕ 330
127
Salt-resistant cross fin & copper tube
Inverter scroll hermetic compressor
Mitsubishi Electric Corporation
Inverter
2.9
-
MEL56 x 2.3 L
100
0 Pa
Propeller fan ✕ 2
DC-control, Direct-driven by motor
0.06 x 2
-
High pressure sensor, High pressure switch 4.15 MPa
Over-heat protection, Over-current protection
Discharge thermo protection, Over-current protection
Over-heat protection, Voltage protection
Auto-defrost mode (Reversed refrigerant circle)
R410A ✕ 8.5kg ( 19 lb)
LEV circuit
Installation Manual
Grounded lead wire ✕ 2
Joint: CMY-Y62G-F ; Header:CMY-Y64/68G-F
3.23
51/53
3.3
-
Only one indoor unit of Fresh Air type is connected with one outdoor unit.
Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be referred to the Installation Manual.
*2 Nominal cooling conditions *3 Nominal heating conditions
27˚CDB/19.5˚CWB
20˚CDB
35˚CDB
7˚CDB/6˚CWB
5m
10m
0m (0ft)
0m (0ft)
Unit converter
kcal= kW ✕ 860
Btu/h= kW ✕ 3,412
cfm= m 3 /min ✕ 35.31
lb= kg/0.4536
* The specification data is subject to rounding variation.
10

OUTDOOR UNIT
Specifications & External Dimensions
New
S SERIES
R410A
PUMY-P100,125,140YHM / PUMY-P100,125,140VHM
External Dimensions
Unit : mm
1 FREE SPACE (Around the unit) 2 SERVICE SPACE
The diagram below shows a
Dimensions of space needed
basic example.
for service access are
Explantion of particular details are
shown in the below diagram.
given in the installation manuals etc.
Over 10mm Over 10mm
FREE
Over 150mm
Over 150mm
Over
10
Service space Over
500
Over Over
500 150
Less than
30
3 FOUNDATION BOLTS
Please secure the unit firmly
with 4 foundation (M10) bolts.
(Bolts and washers must be
purchased locally.)
FOUNDATION
4 PIPING-WIRING DIRECTIONS
Piping and wiring connections
can be made from 4 directions:
FRONT,Right,Rear and Below.
Side Air Intake
30 330
Rear Air Intake
2-U Shaped notched holes
(Foundation Bolt M10)
175 600
175
Installation Feet
2-12 X 36 Oval holes
(Foundation Bolt M10)
Air Discharge
70
56
37
53 56
28 370
417
42
19
Rear Air Intake
Side Air Intake
Handle for moving
322
950
Ground for the power supply
Terminal connection
Left····· For the power supply
Center·····For the transmission line
( Right····· For concentration control )
Ground for the transmission line
Ground for concentration control
Service panel
Example of Notes
Handle for moving
Handle for moving
Handle for moving
1350
635
Handle for moving
1 • • • Refrigerant GAS pipe connction ø15.88 (5/8")Flare
2 • • • Refrigerant LIQUID pipe connection ø 9.52 (3/8")Flare
✻1 • • • Indication of STOP VALVE connection location.
920
Air intake
371
1
✻ 1423
✻1507
2
Piping Knock-Out Hole Details
23
71
Front piping cover
Rear piping cover
Power supply wiring hole
(2-ø27Knock-Out)
Front trunking hole
40 45
(Knock-Out)
ø92
Front piping hole
(Knock-Out) 92
65
27 55
23 73 63
Power supply wiring hole
Right piping hole (2-ø27Knock-Out)
(Knock-Out)
Right trunking hole
(Knock-Out)
75 40
45
19 55
92
65
23 27 92
73 63
ø92
23 73 63
27
55
40
ø92
92
Power supply wiring hole
(2-ø27Knock-Out)
Rear trunking hole
(Knock-Out)
Rear piping hole
(Knock-Out)
81 219
30 220 145 145 145
Drain hole
5-ø33
71
Bottom piping hole
(Knock-Out)
11

OUTDOOR UNIT
Specifications & External Dimensions
Model name
Capacity
Power source
Power input
Current
COP
Heat exchanger type
Type
Starting method
Motor output (kW)
Type ✕ Quantity
Airflow rate
Compressor Fan Protection
Motor output (kW)
High pressure protection
Inverter circuit
Compressor/fan
Refrigerant piping diameter Gas side
mm(in.) Liquid side
Refrigerant type
Noise level (dB) (A-characteristic value) (*3)
External finish
Net weight
Indoor unit
External dimension
Temp. range of
cooling
Temp. range of
heating
Model name
Capacity
Power source
Power input
Current
COP
Heat exchanger type
Type
Starting method
Motor output (kW)
Type ✕ Quantity
Airflow rate
Compressor Fan Protection
mm(in.)
Indoor
Outdoor
Indoor
Outdoor
kW (*1)
kcal/h (*2)
BTU/h (*1)
kW
A
m 3 /min
L/s
cfm
kg(lbs)
Total capacity
Model/Quantity
Height (H)
Width (W)
Depth (D)
W.B.
D.B.
D.B
W.B.
Motor output (kW)
High pressure protection
Inverter circuit
Compressor/fan
Refrigerant piping diameter Gas side
mm(in.) Liquid side
Refrigerant type
Noise level (dB) (A-characteristic value) (*3)
External finish
Net weight
Indoor unit
External dimension
Temp. range of
cooling
Temp. range of
Y SERIES
R410A
mm(in.)
Indoor
Outdoor
Indoor
Outdoor
kW (*1)
kcal/h (*2)
BTU/h (*1)
kW
A
m 3 /min
L/s
cfm
kg(lbs)
Total capacity
Model/Quantity
Height (H)
Width (W)
Depth (D)
W.B.
D.B.
D.B
W.B.
PUY-P200YGM-A
Cooling
22.4
20,000
76,400
6.14
10.3/9.8/9.4
3.65
Specifications
PUHY-P200YGM-A PUHY-P250YGM-A PUHY-P300YGM-A PUHY-P350YGM-A PUHY-P400YGM-A
PUY-P250YGM-A PUY-P300YGM-A PUY-P350YGM-A
Heating Cooling Heating Cooling Heating Cooling Heating Cooling Heating
25.0
28.0
31.5
33.5
37.5
40.0
45.0
45.0
50.0
–
25,000
–
30,000
–
35,000
–
40,000
–
85,300 95,500 107,500
136,500 153,500 153,500 170,600
Note: 1. Cooling/heating capacity indicates the maximum value at operation under the following condition.
*1 (JIS Standard: JIS B8615-1) Cooling 27˚C(81˚F)DB/19˚C(66.2˚F)WB Outdoor: 35˚C(95˚F)DB
Heating Indoor: 20˚C(68˚F)DB Outdoor: 7˚C(44.6˚F)DB/6˚C(42.8˚F)WB
Pipe length: 7.5m(24-9/16Ft) Height difference: 0m
PUHY-P200,250,300,350YGM-A
PUY-P200,250,300,350YGM-A
4.7
5.98
10.0/9.5/9.2
4.18
φ19.05(φ3/4") Brazed
φ9.52(φ3/8") Flare
56
218(481)
Models P20~P250/1~13
Cooling
50.0
45,000
170,600
External Dimensions
114,300 128,000
3N ~ 380/400/415V 50/60Hz
7.72
7.62
9.57
9.1
11.39 11.02 13.42 12.43
13.0/12.3/11.9 12.8/12.2/11.7 16.1/15.3/14.7 15.3/14.5/14.0 19.2/18.2/17.6 18.6/17.6/17.0 22.6/21.5/20.7 20.9/19.9/19.2
3.63
4.13
3.50
4.12
3.51
4.08
3.35
4.02
Salt Ptotected Fin
Inverter scroll hermetic compressor
Inverter
6.7
8.0
9.6
9.7
Propeller fan ✕ 1
200
3,333
7,063
0.38
240
4,000
8,476
0.64
High pressure switch 4.15MPa (601 psi)
Over-voltage and over-current protection for AC bus, Over-heat protection
Over-heat protection/Thermal switch
φ22.2(φ7/8") Brazed
φ28.58(φ1-1/8") Brazed
φ9.52(φ3/8") Flare (φ12.7(φ1/2") for over 90m) φ9.52(φ3/8") Flare (φ12.7(φ1/2") for over 40m)
R410A
φ12.7(φ1/2") Flare
φ12.7(φ1/2") Flare
57
59
60
61
Pre-coated galvanized sheets + powder coating (for-BS type)
233(514)
233(514)
50~130% of outdoor unit capacity
233(514)
275(607)
Models P20~P250/1~16 Models P20~P250/1~19
1840(72-1/2")
Models P20~P250/1~20 Models P20~P250/1~22
990(39")
1290(50-13/16")
840(33-1/8")
15~24˚C (59~75˚F)
-5~43˚C (23~109˚F) 0~43˚C (32~109˚F)(When the Outdoor is at a position lower than the Indoors)
15~27˚C (59~81˚F)
-20~15.5˚C (-4~60˚F)
PUHY-P450YGM-A PUHY-P500YGM-A PUHY-P550YGM-A PUHY-P600YGM-A PUHY-P650YGM-A
Heating Cooling Heating Cooling Heating Cooling Heating Cooling
56.0
56.0
63.0
63.0
67.0
67.4
75.0
73.0
–
50,000
–
55,000
–
60,000
–
65,000
191,100 191,100 215,000
230,000 255,900 249,100
215,000 228,600
3N ~ 380/400/415V 50/60Hz
13.61 13.86 15.59 15.89 17.08 16.37 17.59 17.73
22.9/21.8/21.0 23.3/22.2/21.4 26.3/25.0/24.0 26.8/25.4/24.5 28.8/27.3/26.4 27.6/26.2/25.3 29.6/28.2/27.1 29.9/28.4/27.4
3.67
4.04
3.59
3.96
3.69
4.09
3.83
4.23
Salt Protected Fin
Inverter scroll hermetic compressor + Scroll hermetic
Inverter + Direct
6.8 + 5.3
8.2 + 5.3
9.3 + 5.3
Propeller fan ✕ 2
10.1 + 5.3
400
6,667
14,126
0.38 ✕ 2
High pressure switch 4.15MPa (601 psi)
Over-current protection for AC bus, Over-heat protection
Over-heat protection/Thermal switch
φ28.58(φ1-1/8") Brazed
φ15.88(φ5/8") Flare
R410A
60/61 (50Hz/60Hz) 61/62 (50Hz/60Hz)
Pre-coated galvanized sheets + powder coating (for-BS type)
455(1004)
455(1004)
455(1004)
50~130% of outdoor unit capacity
455(1004)
Models P20~P250/1~24 Models P20~P250/1~24 Models P20~P250/1~24 Models P20~P250/1~32
1840(72-1/2")
1990(78-3/8")
840(33-1/8")
15~24˚C (59~75˚F)
-5~43˚C (23~109˚F) 0~43˚C (32~109˚F)(When the Outdoor is at a position lower than the Indoors)
15~27˚C (59~81˚F)
-20~15.5˚C (-4~60˚F)
Conn. pipe(Gas)
200: ø19.05
250: ø22.2
300: ø22.2
350: ø28.58
A
80
494
166
Y
Y
ø27 Knockout hole
20
553
*2 Cooling Indoor: 27˚C(81˚F)DB/19.5˚C(67.1˚F)WB Outdoor: 35˚C(95˚F)DB
Pipe length: 5m(16-3/8Ft)
Height difference: 0m
16
840
845(mounting pitch)
877
19.65
33.1/31.5/30.3
3.72
10.9 + 5.3
Heating
81.5
–
278,100
19.82
33.4/31.7/30.6
4.11
62/62.5 (50Hz/60Hz)
455(1004)
Models P20~P250/1~32
*3 It is measured in anechoic room.
Unit : mm
57
Conn. pipe(Liquid)
200: ø9.52
250: ø9.52
300: ø9.52
350: ø12.7
70
65 160
ø62 Knockout hole
2X2-14X20 0val hole
768
80
(Mounting hole)
Knockout hole
Changeable to ø27,ø33 by using
attached conduit mounting plate
Air outlet
Cross section X – X
45
900(mounting pitch)
990
Top view
45
265
16
Model
200
250
300
350
A
132
136
136
146
ø53
• Refrigerant (Gas) conn. pipe......1 pc.
(P200type:Packaged in the accessory kit)
(P250,P300,P350type:Already installed on the unit)
• Packing for conn. pipe................1 pc.
(P200type:Not attached)
(P250,P300,P350type:Attached near the ball valve)
• Conduit mouting plate
ø33, ø27..............................1 pc.Each
• Tapping screw M4......................2 pcs.
Note1.Use the opening at the bottom of the unit
when running the power supply line from
the front or from the side of the unit.
Note2.Please refer to (2/2) for information
regarding necessary spacing around the
unit and foundation work.
12 5
Cross section Y – Y
Air
inlet
90
10
37 117 117 37
Left side view
Air
inlet
ø27 Knockout hole
135
80 40
134 100
280
Knockout hole
Knockout hole
Service panel
Refrig. service
valve (Liquid)
X
44
235
150
67 160
100 83
Knockout hole
207 67
valve(Gas)
Front view
X
78
11
1575
1840
12

OUTDOOR UNIT
Specifications & External Dimensions
Y SERIES
R410A
External Dimensions
PUHY-P400YGM-A
644
Unit : mm
503
145
57 80
166
65 160
1068
80 ø62 Knockout hole
Changeable to ø46,ø53 by using
Conn. pipe(Gas)
Cross section X – X attached conduit mounting plate
ø28.58
Conn. pipe(Liquid)
Air outlet
ø12.7
265
16
Knockout hole
Y
Y
ø27 Knockout hole
840
845(mounting pitch)
877
20
70
2X2-14X20 Oval hole
(Mounting hole)
45
1200(mounting pitch)
1290
Top view
45
ø53
16
12 5
Air
inlet
Cross section Y – Y
• Refrigerant (Gas) conn. pipe......1 pc.
(Already installed on the unit)
• Packing for conn. pipe................1 pc.
(Attached near the ball valve)
• Conduit mouting plate
ø53, ø46.............................1 pc.Each
• Tapping screw M4.....................2 pcs.
Note1.Use the opening at the bottom of the unit
when running the power supply line from
the front or from the side of the unit.
Note2.Please refer to (2/2) for information
regarding necessary spacing around the
unit and foundation work.
Air
inlet
10 89
37
115
Left side view
ø27 Knockout hole
80 40
100
134
280
Knockout hole
Service panel
Refrig. service
valve (Liquid)
X
44
235
150
Knockout hole
115 37 Refrig. service
valve(Gas)
100
67 160
83
68 355
Knockout hole
Front view
355 68
X
78
11
1575
1840
PUHY-P450,500,550,600,650YGM-A
Knockout hole
145
80
57
Conn. pipe(Gas)
ø28.58
65 160
494
162
768
Conn. pipe(Liquid)
ø15.88
Y
Y
1000
ø27 Knockout hole
20
70
Y
Y
ø62 Knockout hole
3X2-14X20 Oval hole
80
Changeable to ø46,ø53 by using
(Mounting hole)
attached conduit mounting plate
Cross section X – X
553
45
950(mounting pitch)
1990
Top view
950(mounting pitch)
840
45
16 845(mounting pitch) 16
877
Air outlet
ø53
265
13
12
5
Cross section Y – Y
• Refrigerant (Gas) conn. pipe....1 pc.
(Already installed on the unit)
• Packing for conn. pipe......1 pc.
(Attached near the ball valve)
• Conduit mouting plate
ø53, ø46......1 pc.Each
• Tapping screw M4...2 pcs.
Note1.Use the opening at the bottom of the unit
when running the power supply line from
the front or from the side of the unit.
Note2.Please refer to (2/2) for information
regarding necessary spacing around the
unit and foundation work.
Air
inlet
89
10
Air
inlet
ø27 Knockout hole
80 40
Knockout hole
37 115 115 37
Left side view
134 100
280
Knockout hole
Service panel
Refrig. service
valve (Liquid)
44
235
150
X
Refrig. service
valve(Gas)
67 160
100 83
Knockout hole
68 205
205
Front view
68
11 78
1575
X
1840

OUTDOOR UNIT
Specifications & External Dimensions
Y SERIES
R410A
Model name
Capacity
kW (*1)
kcal/h (*2)
BTU/h (*1)
Power source
Power input
kW
Current
A
COP
Composing unit model name
Heat exchanger type
Type
Starting method
Motor output (kW)
Type ✕ Quantity
m 3 /min
Airflow rate L/s
cfm
Motor output (kW)
High pressure protection
Inverter circuit
Compressor/fan
Gas side (main)(mm(in.))
Gas side (between Comp unit and HEX unit)(mm(in.)
Liquid side (main)(mm(in.))
Liquid side (between Comp unit and HEX unit)(mm(in.))
Refrigerant type
Noise level (dB)
Set
(A-characteristic value) (*3)
External finish
Net weight
kg(lbs)
Total capacity
Indoor unit
Model/Quantity
Height (H)
External dimension
Width (W)
(mm(in.))
Depth (D)
Indoor W.B.
Temp. range of cooling
Outdoor D.B.
Indoor D.B
Temp. range of heating
Outdoor W.B.
Compressor Fan Protection
Refrigerant
piping diameter
Specifications
PUHY-P700YSGM-A
PUHY-P750YSGM-A
Cooling
Heating
Cooling
Heating
78.4
70,000
267,500
21.7
36.6/34.8/33.5
3.61
88.0
–
300,300
3N ~ 380/400/415V 50/60Hz
21.83
84.0
75,000
286,600
24.9
36.8/35.0/33.7
42.0/39.9/38.4
4.03
3.37
94.5
–
322,400
25.37
42.8/40.6/39.2
3.72
PUHY-P700YGM-A (Compressor unit) PUHN-P01YGM-A (Heat exchanger unit) PUHY-P750YGM-A (Compressor unit) PUHN-P01YGM-A (Heat exchanger unit)
Salt Protected Fin
Inverter scroll hermetic compressor ✕ 2
–
Inverter
–
8.6 + 8.6
–
Propeller fan ✕ 1
Propeller fan ✕ 1
240
240
4,000
4,000
8,476
8,476
0.64
0.64
High pressure switch 4.15MPa (601 psi)
–
Over-voltage and over-current protection for AC bus, Over-heat protection
Over-heat protection/Thermal switch
R410A
62
–
Thermal switch
Inverter scroll hermetic compressor ✕ 2
–
Inverter
–
9.4 + 9.4
–
Propeller fan ✕ 1
Propeller fan ✕ 1
240
240
4,000
4,000
8,476
8,476
0.64
0.64
High pressure switch 4.15MPa (601 psi)
–
Over-voltage and over-current protection for AC bus, Over-heat protection
–
Over-heat protection/Thermal switch
Thermal switch
φ34.93(φ1-3/8") Brazed
φ28.58(φ1-1/8") Flange / φ28.58(φ1-1/8") Brazed
φ19.05(φ3/4") Brazed + Flare
φ12.7(φ1/2") Flare / φ12.7(φ1/2") Brazed
–
R410A
–
63
Pre-coated galvanized sheets + powder coating (for-BS type)
430(948)
155(342)
430(948)
155(342)
50~130% of outdoor unit capacity
Models P20~P250/1~34
Models P20~P250/1~34
1840(72-1/2")
1690(66-9/16")
990(39")
1690(66-9/16")
990(39")
840(33-1/8")
15~24˚C (59~75˚F)
-5~43˚C (23~109˚F) 0~43˚C (32~109˚F)(When the Outdoor is at a position lower than the Indoors)
15~27˚C (59~81˚F)
-20~15.5˚C (-4~60˚F)
Model name
Capacity
Compressor Fan Protection
Refrigerant
piping diameter
kW (*1)
kcal/h (*2)
PUHY-P800YSGM-A
Cooling
Heating
90.0
100.0
80,000
–
307,100
341,200
3N ~ 380/400/415V 50/60Hz
26.75
26.9
45.1/42.9/41.3
45.4/43.1/41.5
3.36
3.72
PUHY-P800YGM-A (Compressor unit)
PUHN-P01YGM-A (Heat exchanger unit)
Salt Protected Fin
Inverter scroll hermetic compressor ✕ 2
–
Inverter
–
10.1 + 10.1
–
Propeller fan ✕ 1
Propeller fan ✕ 1
240
240
4,000
4,000
8,476
8,476
0.64
0.64
High pressure switch 4.15MPa (601 psi)
–
Over-voltage and over-current protection for AC bus, Over-heat protection
–
Over-heat protection/Thermal switch
Thermal switch
φ34.93(φ1-3/8") Brazed
φ28.58(φ1-1/8") Flange / φ28.58(φ1-1/8") Brazed
φ19.05(φ3/4") Brazed + Flare
φ12.7(φ1/2") Flare / φ12.7(φ1/2") Brazed
R410A
–
64
Pre-coated galvanized sheets + powder coating (for-BS type)
430(948)
155(342)
50~130% of outdoor unit capacity
Models P20~P250/1~34
1840(72-1/2")
1690(66-9/16")
990(39")
840(33-1/8")
15~24˚C (59~75˚F)
-5~43˚C (23~109˚F) 0~43˚C (32~109˚F)(When the Outdoor is at a position lower than the Indoors)
15~27˚C (59~81˚F)
-20~15.5˚C (-4~60˚F)
BTU/h (*1)
Power source
Power input
kW
Current
A
COP
Composing unit model name
Heat exchanger type
Type
Starting method
Motor output (kW)
Type ✕ Quantity
m 3 /min
Airflow rate L/s
cfm
Motor output (kW)
High pressure protection
Inverter circuit
Compressor/fan
Gas side (main)(mm(in.))
Gas side (between Comp unit and HEX unit)(mm(in.)
Liquid side (main)(mm(in.))
Liquid side (between Comp unit and HEX unit)(mm(in.))
Refrigerant type
Noise level (dB)
Set
(A-characteristic value) (*3)
External finish
Net weight
kg(lbs)
Total capacity
Indoor unit
Model/Quantity
Height (H)
External dimension
Width (W)
(mm(in.))
Depth (D)
Indoor W.B.
Temp. range of cooling
Outdoor D.B.
Indoor D.B
Temp. range of heating
Outdoor W.B.
Note: 1. Cooling/heating capacity indicates the maximum value at operation under the following condition.
*1 (JIS Standard: JIS B8615-1) Cooling 27˚C(81˚F)DB/19˚C(66.2˚F)WB Outdoor: 35˚C(95˚F)DB
Heating Indoor: 20˚C(68˚F)DB Outdoor: 7˚C(44.6˚F)DB/6˚C(42.8˚F)WB
Pipe length: 7.5m(24-9/16Ft) Height difference: 0m
*2 Cooling Indoor: 27˚C(81˚F)DB/19.5˚C(67.1˚F)WB Outdoor: 35˚C(95˚F)DB
Pipe length: 5m(16-3/8Ft)
Height difference: 0m
*3 It is measured in anechoic room.
14

3
OUTDOOR UNIT
Specifications & External Dimensions
Y SERIES
R410A
External Dimensions
PUHY-P700,750,800YGM-A
Knockout hole
Refrig.service valve
(Liquid pipe to HEX unit)
ø12.7
Refrig.service valve
(Gas pipe to HEX unit)
ø28.58
161
107
Refrig.service valve
(Gas pipe to indoor unit)
Refrig.service valve
(Liquid pipe to indoor unit)
124
159
ø75 Knockout hole
Changeable to ø62 by using
attached conduit mounting plate
ø27 Knockout hole
Cross section X – X
Air outlet
3 X 2 – 14 X 20 Oval hole
(Mounting hole)
45
800(mounting pitch)
800(mounting pitch)
1690
Top view
840
45
16 845(mounting pitch) 16
877
Unit : mm
• Refrigerant conn. pipe with flange (to indoor unit:Gas)....1 pc.
(Already installed on the unit)
• Refrigerant conn. pipe with flange (to HEX unit:Gas).......1 pc.
(Already installed on the unit)
• Packing for conn. pipe with flange (to indoor unit:Gas)....1 pc.
(Attached near ball valve)
• Packing for conn. pipe with flange (to HEX unit:Gas)......1 pc.
(Attached near ball valve)
• Conduit mouting plate
ø62...........................1 pc.
• Tapping screw µ4.....2 pcs.
Air
inlet
Air
inlet
Service panel
Knockout hole
265
1840
Note1.Use the opening at the bottom of the unit
when running the power supply line from
the front or from the side of the unit.
Note2.Please refer to (2/2) for information
regarding necessary space around the
unit and foundation work.
10 89
135
80
40
100
134
37 175
175 37
ø27 Knockout hole
280
Knockout hole
Service panel
12
11
241
Knockout hole
X
117
83
254
88
Conn. pipe(Gas)
ø34.93
Conn. pipe(Liquid)
ø19.05
11 78
1575
X
PUHN-P01YGM-A
ø27hole+rubber bush
(Bottom of controlbox)
82
120
60 ø27hole+rubber bush
(Bottom of controlbox)
Cross section x-x
Air outlet
Left side view
2x2-14x20 Oval hole
45 900(mounting pitch) 45
(Mounting hole)
990
Top view
840
16 845(mounting pitch) 16
877
Front view
Note1.Use the opening at the bottom of the unit
when running the power supply line from
the front or from the side of the unit.
Note2.Please refer to (2/2) for information
regarding necessary space around the
unit and foundation work.
Air outlet
265
Air
inlet
Air
inlet
1575
1840
Air
inlet
Air
inlet
Refrig. service valve x
(Gas pipe to compressor unit)
ø28.58
70
45
x
50
Knockout hole
40
80
PUHY-P700,750,800YSGM-A
10 90
37 117 Air 117 37
inlet
Left side view
877
Refrig. service valve
(Liquid pipe to compressor unit)
ø12.7
67
207
80
Knockout hole 207 67
Front view
11 78
165
250
2690
115
134
157
Air
inlet
Right side view
840
Air outlet
990 10
1690
HEX unit
Compressor unit
Air
inlet
Air
inlet
1575 265
1840
Gas pipe used to connect
compressor unit and HEX unit
Conn.pipe(Gas)
ø34.93
Conn.pipe(Liquid)
ø19.05
15
Left side view
Liquid pipe used to connect
compressor unit and HEX unit
Front view

OUTDOOR UNIT
Specifications & External Dimensions
Model name
Capacity (*1)
Current input A
COP
Power source
Composing unit model name
Heat exchanger type
Type
Starting method
Motor output (kW)
Type ✕ Quantity
m 3/min
Airflow rate
L/s
cfm
Motor output (kW)
High pressure protection
Inverter circuit
Compressor/fan
Compressor Fan Protection
Refrigerant
piping diameter
Gas side (main)(mm(in.))
Gas side (between unit and distributor)(mm(in.))
Liquid side (main)(mm(in.))
Liquid side (between unit and distributor)(mm(in.))
Oil balance pipe(mm(in.))
Refrigerant type
Noise level (dB)
(A-characteristic value) (*3)
External finish
Net weight
Indoor unit
Power input
External dimension
(mm(in.))
Temp. range of cooling
Temp. range of heating
Model name
Capacity (*1)
Set
kW
Btu/h(*1)
kcal/h(*2)
kW
kg (lbs.)
Total capacity
Model / Quantity
Height (H)
Width (W)
Depth (D)
Indoor W.B.
Outdoor D.B.
Indoor D.B.
Outdoor W.B.
Current input A
COP
Power source
Composing unit model name
Heat exchanger type
Type
Starting method
Motor output (kW)
Type ✕ Quantity
m 3/min
Airflow rate
L/s
cfm
Motor output (kW)
High pressure protection
Inverter circuit
Compressor/fan
Compressor Fan Protection
Refrigerant
piping diameter
Gas side (main)(mm(in.))
Gas side (between unit and distributor)(mm(in.))
Liquid side (main)(mm(in.))
Liquid side (between unit and distributor)(mm(in.))
Oil balance pipe(mm(in.))
Refrigerant type
Noise level (dB)
(A-characteristic value) (*3)
External finish
Net weight
Indoor unit
External dimension
(mm(in.))
Temp. range of cooling
Temp. range of heating
Note:
Y SERIES
Power input
R410A
Set
kW
Btu/h(*1)
kcal/h(*2)
kW
kg (lbs.)
Total capacity
Model / Quantity
Height (H)
Width (W)
Depth (D)
Indoor W.B.
Outdoor D.B.
Indoor D.B.
Outdoor W.B.
Cooling
96.0
327,500
85,000
25.28
42.6/40.5/39.0
3.80
PUHY-P850YSGM-A
Heating
108.0
368,500
–
27.47
46.3/44.0/42.4
3.93
Specifications
Cooling
101.0
344,600
90,000
26.71
45.0/42.8/41.2
3.78
PUHY-P900YSGM-A
Heating
113.0
385,500
–
29.10
49.1/46.6/44.9
3.88
3-phase 4-wire 380/400/415V 50/60Hz
PUHY-P450YMM-A PUHY-P400YSM-A PUHY-P500YMM-A PUHY-P400YSM-A
Salt-resistant cross fin & copper tube
Inverter scroll hermetic comp. + Scroll hermetic comp.
Inverter + Direct
9.4 + 5.3 / 8.5 + 5.3
Propeller fan ✕ 2
400
6,667
14,126
0.38 ✕ 2
8.5 + 5.3 / 8.5 + 5.3
Propeller fan ✕ 2
400
6,667
14,126
0.38 ✕ 2
High pressure switch 4.15MPa (601 psi)
Over-voltage and over-current protection for AC bus, Over-heat protection
Over-heat protection/Thermal switch
10.3 + 5.3 / 9.6 + 5.3
Propeller fan ✕ 2
400
6,667
14,126
0.38 ✕ 2
High pressure switch 4.15MPa (601 psi)
Over-voltage and over-current protection for AC bus, Over-heat protection
Over-heat protection/Thermal switch
φ41.28(φ1-5/8") Brazed
φ28.58(φ1-1/8") Brazed
φ19.05(φ3/4") Brazed
φ15.88(φ5/8") Flare
φ9.52(φ3/8") Flare
R410A
63/64 63/64
8.5 + 5.3 / 8.5 + 5.3
Propeller fan ✕ 2
400
6,667
14,126
0.38 ✕ 2
Cooling
108.0
368,500
95,000
29.23
49.3/46.8/45.1
3.69
PUHY-P550YMM-A
11.2 + 5.3 / 10.9 + 5.3
Propeller fan ✕ 2
400
6,667
14,126
0.38 ✕ 2
PUHY-P950YSGM-A
Heating
119.5
407,700
–
30.42
51.3/48.7/47.0
3.93
PUHY-P400YSM-A
8.5 + 5.3 / 8.5 + 5.3
Propeller fan ✕ 2
400
6,667
14,126
0.38 ✕ 2
High pressure switch 4.15MPa (601 psi)
Over-voltage and over-current protection for AC bus, Over-heat protection
Over-heat protection/Thermal switch
Pre-coated galvanized sheets + powder coating (for-BS type)
458 (1010) 460 (1015) 458 (1010) 460 (1015) 458 (1010) 460 (1015)
50~130% of outdoor unit capacity
P20~P250 / 1~42
1840 (72-1/2")
1990 (78-3/8")
840 (33-1/8")
15~24˚C (59~75˚F)
-5~43˚C (23~109˚F) 0~43˚C (32~109˚F)(When the Outdoor is at a position lower than the Indoors)
15~27˚C (59~81˚F)
-20~15.5˚C (-4~60˚F)
Cooling
113.0
385,500
100,000
31.11
52.5/49.8/48.0
3.63
PUHY-P1000YSGM-A
Heating
127.0
433,300
–
32.68
55.1/52.4/50.5
3.89
Cooling
118.0
402,600
105,000
33.48
56.5/53.6/51.7
3.52
PUHY-P1050YSGM-A
63/64
Heating
132.0
450,300
–
34.24
57.8/54.9/52.9
3.86
3-phase 4-wire 380/400/415V 50/60Hz
PUHY-P600YMM-A PUHY-P400YSM-A PUHY-P650YMM-A PUHY-P400YSM-A
Salt-resistant cross fin & copper tube
Inverter scroll hermetic comp. + Scroll hermetic comp.
Inverter + Direct
11.6 + 5.3 / 11.6 + 5.3
Propeller fan ✕ 2
400
6,667
14,126
0.38 ✕ 2
8.5 + 5.3 / 8.5 + 5.3
Propeller fan ✕ 2
400
6,667
14,126
0.38 ✕ 2
High pressure switch 4.15MPa (601 psi)
Over-voltage and over-current protection for AC bus, Over-heat protection
Over-heat protection/Thermal switch
φ41.28(φ1-5/8") Brazed
φ28.58(φ1-1/8") Brazed
φ19.05(φ3/4") Brazed
φ15.88(φ5/8") Flare
φ9.52(φ3/8") Flare
R410A
11.6 + 5.3 / 11.6 + 5.3
8.5 + 5.3 / 8.5 + 5.3
Propeller fan ✕ 2
Propeller fan ✕ 2
400
400
6,667
6,667
14,126
14,126
0.38 ✕ 2
0.38 ✕ 2
High pressure switch 4.15MPa (601 psi)
Over-voltage and over-current protection for AC bus, Over-heat protection
Over-heat protection/Thermal switch
63/64 63.5/64.5
Pre-coated galvanized sheets + powder coating (for-BS type)
458 (1010) 460 (1015) 458 (1010) 460 (1015)
50~130% of outdoor unit capacity
P20~P250 / 1~42
1840 (72-1/2")
1990 (78-3/8")
840 (33-1/8")
15~24˚C (59~75˚F)
-5~43˚C (23~109˚F) 0~43˚C (32~109˚F)(When the Outdoor is at a position lower than the Indoors)
15~27˚C (59~81˚F)
-20~15.5˚C (-4~60˚F)
1. Cooling/heating capacity indicates the maximum value at operation under the following condition.
*1 (JIS Standard: JIS B8615-1) Cooling 27˚C(81˚F)DB/19˚C(66.2˚F)WB Outdoor: 35˚C(95˚F)DB
Heating Indoor: 20˚C(68˚F)DB Outdoor: 7˚C(44.6˚F)DB/6˚C(42.8˚F)WB
Pipe length: 7.5m(24-9/16Ft) Height difference: 0m
*2 Cooling Indoor: 27˚C(81˚F)DB/19.5˚C(67.1˚F)WB Outdoor: 35˚C(95˚F)DB
Pipe length: 5m(16-3/8Ft)
Height difference: 0m
*3 It is measured in anechoic room.
16

OUTDOOR UNIT
Specifications & External Dimensions
Y SERIES
R410A
Model name
Capacity (*1)
Current input A
COP
Power source
Composing unit model name
Heat exchanger type
Type
Starting method
Motor output (kW)
Type ✕ Quantity
m 3/min
Airflow rate
L/s
cfm
Motor output (kW)
High pressure protection
Inverter circuit
Compressor/fan
Compressor Fan Protection
Refrigerant
piping diameter
Gas side (main)(mm(in.))
Gas side (between unit and distributor)(mm(in.))
Liquid side (main)(mm(in.))
Liquid side (between unit and distributor)(mm(in.))
Oil balance pipe(mm(in.))
Refrigerant type
Noise level (dB)
(A-characteristic value) (*3)
External finish
Net weight
Indoor unit
Power input
External dimension
(mm(in.))
Temp. range of cooling
Temp. range of heating
Set
kW
Btu/h(*1)
kcal/h(*2)
kW
kg (lbs.)
Total capacity
Model / Quantity
Height (H)
Width (W)
Depth (D)
Indoor W.B.
Outdoor D.B.
Indoor D.B.
Outdoor W.B.
Cooling
124.0
423,000
110,000
36.39
61.4/58.3/56.2
3.41
PUHY-P1100YSGM-A
Specifications
Heating
140.0
477,600
–
36.93
62.3/59.2/57.0
3.79
Cooling
130.0
443,500
115,000
39.96
67.4/64.0/61.7
3.25
PUHY-P1150YSGM-A
Heating
145.0
494,700
–
38.46
64.9/61.6/59.4
3.77
3-phase 4-wire 380/400/415V 50/60Hz
PUHY-P450YMM-A PUHY-P650YSM-A PUHY-P500YMM-A PUHY-P650YSM-A
Salt-resistant cross fin & copper tube
Inverter scroll hermetic comp. + Scroll hermetic comp.
Inverter + Direct
9.4 + 5.3 / 8.5 + 5.3
Propeller fan ✕ 2
400
6,667
14,126
0.38 ✕ 2
11.6 + 5.3 / 11.6 + 5.3
Propeller fan ✕ 2
400
6,667
14,126
0.38 ✕ 2
High pressure switch 4.15MPa (601 psi)
Over-voltage and over-current protection for AC bus, Over-heat protection
Over-heat protection/Thermal switch
φ41.28(φ1-5/8") Brazed
φ28.58(φ1-1/8") Brazed
φ19.05(φ3/4") Brazed
φ15.88(φ5/8") Flare
φ9.52(φ3/8") Flare
R410A
10.3 + 5.3 / 9.6 + 5.3
11.6 + 5.3 / 11.6 + 5.3
Propeller fan ✕ 2
Propeller fan ✕ 2
400
400
6,667
6,667
14,126
14,126
0.38 ✕ 2
0.38 ✕ 2
High pressure switch 4.15MPa (601 psi)
Over-voltage and over-current protection for AC bus, Over-heat protection
Over-heat protection/Thermal switch
64/65 64/65
Pre-coated galvanized sheets + powder coating (for-BS type)
458 (1010) 460 (1015) 458 (1010) 460 (1015)
50~130% of outdoor unit capacity
P20~P250 / 1~42
1840 (72-1/2")
1990 (78-3/8")
840 (33-1/8")
15~24˚C (59~75˚F)
-5~43˚C (23~109˚F) 0~43˚C (32~109˚F)(When the Outdoor is at a position lower than the Indoors)
15~27˚C (59~81˚F)
-20~15.5˚C (-4~60˚F)
Model name
Capacity (*1)
Current input A
COP
Power source
Composing unit model name
Heat exchanger type
Type
Starting method
Motor output (kW)
Type ✕ Quantity
m 3/min
Airflow rate
L/s
cfm
Motor output (kW)
High pressure protection
Inverter circuit
Compressor/fan
Compressor Fan Protection
Refrigerant
piping diameter
Gas side (main)(mm(in.))
Gas side (between unit and distributor)(mm(in.))
Liquid side (main)(mm(in.))
Liquid side (between unit and distributor)(mm(in.))
Oil balance pipe(mm(in.))
Refrigerant type
Noise level (dB)
(A-characteristic value) (*3)
External finish
Net weight
Indoor unit
Power input
External dimension
(mm(in.))
Temp. range of cooling
Temp. range of heating
Note:
Set
kW
Btu/h(*1)
kcal/h(*2)
kW
kg (lbs.)
Total capacity
Model / Quantity
Height (H)
Width (W)
Depth (D)
Indoor W.B.
Outdoor D.B.
Indoor D.B.
Outdoor W.B.
Cooling
136.0
464,000
120,000
44.40
74.9/71.2/68.6
3.06
PUHY-P1200YSGM-A
Heating
150.0
511,700
–
39.73
67.0/63.7/61.4
3.78
Cooling
140.0
477,600
125,000
47.56
80.2/76.2/73.5
2.94
PUHY-P1250YSGM-A
Heating
156.5
533,900
–
42.63
71.9/68.3/65.8
3.67
3-phase 4-wire 380/400/415V 50/60Hz
PUHY-P550YMM-A PUHY-P650YSM-A PUHY-P600YMM-A PUHY-P650YSM-A
Salt-resistant cross fin & copper tube
Inverter scroll hermetic comp. + Scroll hermetic comp.
Inverter + Direct
11.2 + 5.3 / 10.9 + 5.3
Propeller fan ✕ 2
400
6,667
14,126
0.38 ✕ 2
11.6 + 5.3 / 11.6 + 5.3
Propeller fan ✕ 2
400
6,667
14,126
0.38 ✕ 2
High pressure switch 4.15MPa (601 psi)
Over-voltage and over-current protection for AC bus, Over-heat protection
Over-heat protection/Thermal switch
φ41.28(φ1-5/8") Brazed
φ28.58(φ1-1/8") Brazed
φ19.05(φ3/4") Brazed
φ15.88(φ5/8") Flare
φ9.52(φ3/8") Flare
R410A
11.6 + 5.3 / 11.6 + 5.3
11.6 + 5.3 / 11.6 + 5.3
Propeller fan ✕ 2
Propeller fan ✕ 2
400
400
6,667
6,667
14,126
14,126
0.38 ✕ 2
0.38 ✕ 2
High pressure switch 4.15MPa (601 psi)
Over-voltage and over-current protection for AC bus, Over-heat protection
Over-heat protection/Thermal switch
64/65 65/65.5
Pre-coated galvanized sheets + powder coating (for-BS type)
458 (1010) 460 (1015) 458 (1010) 460 (1015)
50~130% of outdoor unit capacity
P20~P250 / 1~42
1840 (72-1/2")
1990 (78-3/8")
840 (33-1/8")
15~24˚C (59~75˚F)
-5~43˚C (23~109˚F) 0~43˚C (32~109˚F)(When the Outdoor is at a position lower than the Indoors)
15~27˚C (59~81˚F)
-20~15.5˚C (-4~60˚F)
1. Cooling/heating capacity indicates the maximum value at operation under the following condition.
*1 (JIS Standard: JIS B8615-1) Cooling 27˚C(81˚F)DB/19˚C(66.2˚F)WB Outdoor: 35˚C(95˚F)DB
Heating Indoor: 20˚C(68˚F)DB Outdoor: 7˚C(44.6˚F)DB/6˚C(42.8˚F)WB
Pipe length: 7.5m(24-9/16Ft) Height difference: 0m
*2 Cooling Indoor: 27˚C(81˚F)DB/19.5˚C(67.1˚F)WB Outdoor: 35˚C(95˚F)DB
Pipe length: 5m(16-3/8Ft)
Height difference: 0m
*3 It is measured in anechoic room.
17

OUTDOOR UNIT
Specifications & External Dimensions
Y SERIES
R410A
External Dimensions
PUHY-P450,500,550,
600,650YMM-A
Refrig.service valve
Refrig.service valve
Knockout hole
494
Y
Y
1000
Y
ø27 Knockout hole
Y
553
840
845(mounting pitch) 16
877
145
57 80
76
Conn. pipe
ø28.58
65 160
768
70 20
ø62 Knockout hole
80
Changeable to ø46,ø53 by using attached
conduit mounting plate
Cross section X–X
Air outlet
45
950(mounting pitch)
3✕2–14✕20 Oval hole
(Mounting hole)
1990
Top view
950(mounting pitch) 45
ø53
16
265
12 5
Cross section Y–Y
Air
inlet
• Refrigerant(Gas) conn.pipe....1pc.
(Already installed on the unit)
• Packing for conn.pipe....1pc.
(Attached near the ball valve)
• Conduit mounting plate
ø53, ø46...1pc.Each
• Tapping screw M4....2pcs.
Note1.Use the opening at the bottom of the unit
when running the power supply line from
the front or from the side of the unit.
Note2.Please refer to (2/2) for information
regarding necessary spacing around the
unit and foundation work.
Note3.This unit is used in combination with
a sub unit.(Refer to Drawing No.W656886
Outline Drawing of Outdoor Unit set)
10 89
Air
inlet
37
115
Left side view
ø27 Knockout hole
80 40
115
37
100
134
280
Knockout hole
Knockout hole
Knockout hole
235
217
194
Refrig.service valve
Service panel
Refrig.service valve
163
X
67 160
100
Service valve
Conn. pipe
68 205 ø15.88 ø9.52
205 68
285
48
Front view
78
11
1575
X
1840
PUHY-P450,650YSM-A
Refrig.service valve
Refrig.service valve
Knockout hole
494
Y
Y
1000
Y
ø27 Knockout hole
Y
553
840
845(mounting pitch) 16
877
57 80
92
76
65 160
768
70 20
ø62 Knockout hole
80
Changeable to ø46,ø53 by using attached
conduit mounting plate
Cross section X–X
Air outlet
45
950(mounting pitch)
3✕2–14✕20 Oval hole
(Mounting hole)
1990
Top view
950(mounting pitch) 45
16
ø53
265
12 5
Cross section Y–Y
• Gas distributor....1pc.
(Already installed on the unit)
• Liquid distributor....1pc.
• Packing for conn. pipe....1pc.
(Attached near the gas distributor)
• Conduit mounting plate
ø53, ø46....1pc.Each
• Tapping screw M4....2pcs.
• Conn. pipe(Gas)....2pcs.
Note1.Use the opening at the bottom of the unit
when running the power supply line from
the front or from the side of the unit.
Note2.Please refer to (2/2) for information
regarding necessary spacing around the
unit and foundation work.
Note3.This unit is used in combination with
a main unit.(Refer to Drawing No.W656886
Outline Drawing of Outdoor Unit set)
10 89
Air
inlet
37
115
Left side view
ø27 Knockout hole
80 40
115
Air
inlet
37
100
134
280
Knockout hole
Knockout hole
Service panel
Conn.pipe
ø41.28
Conn.pipe
ø28.58
45
245
235
217
Knockout hole
X
163
67
100
68
205
285
62
160
48
Service valve
ø9.52
Conn.pipe
ø15.88
Front view
205 68
11 78
1575
X
1840
PUHY-P850,900,950,
1000,1050,1100,1150,
1200,1250YSGM-A
877
840
Air outlet
1990
Main unit
10
1990
Sub unit
Air
inlet
Air
inlet
Distributor(Gas)
f
Left side view
d
c
PUHY-P850YSGM-A PUHY-P900YSGM-A PUHY-P950YSGM-A PUHY-P1000YSGM-A PUHY-P1050YSGM-A PUHY-P1100YSGM-A PUHY-P1150YSGM-A PUHY-P1200YSGM-A PUHY-P1250YSGM-A
Main unit
PUHY-P450YMM-A PUHY-P500YMM-A PUHY-P550YMM-A PUHY-P600YMM-A PUHY-P650YMM-A PUHY-P450YMM-A PUHY-P500YMM-A PUHY-P550YMM-A PUHY-P600YMM-A
Sub unit
PUHY-P400YSM-A
PUHY-P650YSM-A
Indoor units~ Liquid a
ø19.05
Distributor Gas b
ø41.28
Distributor~ Liquid c
ø15.88
Main unit Gas d
ø28.58
Distributor~ Liquid e
ø15.88
Sub unit Gas f
ø28.58
Oil balance pipe g
ø9.52
b a
Indoor units
g
e
Distributor(Liquid)
Note1.Pipe size is as show in the table on the left.
Front view
18

OUTDOOR UNIT
Specifications & External Dimensions
R2 SERIES
R410A
Model name
Capacity
Power source
Power input
Current
COP
Heat exchanger type
Type
Starting method
Motor output (kW)
Type ✕ Quantity
Airflow rate
Compressor Fan Protection device
Motor output (kW)
High pressure protection
Inverter circuit
Compressor/fan
Refrigerant piping diameter Gas side
(mm(in.)) Liquid side
Refrigerant type
Noise level (dB) (A-characteristic value) (*3)
External finish
Net weight
Indoor unit
External dimension
Temp. range of
cooling
Temp. range of
heating
(mm(in.))
Indoor
Outdoor
Indoor
Outdoor
kW (*1)
kcal/h (*2)
BTU/h (*1)
kW
A
m3/min
L/s
cfm
kg (lbs)
Total capacity
Model/Quantity
Height (H)
Width (W)
Depth (D)
W.B.
D.B.
D.B
W.B.
Cooling
22.4
20,000
76,400
6.14
10.3/9.8/9.4
3.65
4.7
φ19.05(φ3/4") brazed
φ15.88(φ5/8") brazed
56
236(521)
Models P20~P250/1~15
Specifications
PURY-P200YGM-A PURY-P250YGM-A PURY-P300YGM-A PURY-P350YGM-A PURY-P400YGM-A
Heating Cooling Heating Cooling Heating Cooling Heating Cooling
25.0
28.0
31.5
33.5
37.5
40.0
45.0
45.0
–
25,000
–
30,000
–
35,000
–
40,000
85,300 95,500 107,500
136,500 153,500 153,500
5.98
10.0/9.5/9.2
4.18
114,300 128,000
3N ~ 380/400/415V 50/60Hz
Heating
50.0
–
170,600
7.72
7.62
9.57
9.1
11.39
11.02
13.42
12.43
13.0/12.3/11.9 12.8/12.2/11.7 16.1/15.3/14.7 15.3/14.5/14.0 19.2/18.2/17.6 18.6/17.6/17.0 22.6/21.5/20.7 20.9/19.9/19.2
3.63
4.13
3.50
4.12
3.51
4.08
3.35
4.02
Salt Protected Fin
Inverter scroll hermetic compressor
Inverter
6.7
8.0
Propeller fan ✕ 1
9.6
9.7
200
3,333
7,063
0.38
240
4,000
8,476
0.64
High pressure switch 4.15MPa (601 psi)
Over-voltage and over-current protection for AC bus, Over-heat protection
Over-heat protection/Thermal switch
φ22.2(φ7/8") brazed
φ28.58(φ1-1/8") brazed
φ19.05(φ3/4") brazed
φ22.2(φ7/8") brazed
R410A
57
59
60
61
Pre-coated galvanized sheets + powder coating (for-BS type)
251(554)
251(554)
50~150% of outdoor unit capacity
251(554)
291(642)
Models P20~P250/1~16 Models P20~P250/1~16
1840(72-1/2")
Models P20~P250/1~20 Models P20~P250/1~24
990(39")
1290(50-13/16")
840(33-1/8")
15~24˚C (59~75˚F)
-5~43˚C (23~109˚F) 0~43˚C (32~109˚F)(When the Outdoor is at a position lower than the Indoors)
15~27˚C (59~81˚F)
-20~15.5˚C (-4~60˚F)
Model name
Capacity
Power source
Power input
Current
COP
Heat exchanger type
Type
Starting method
Motor output (kW)
Type ✕ Quantity
Airflow rate
Compressor Fan Protection device
Motor output (kW)
High pressure protection
Inverter circuit
Compressor/fan
Refrigerant piping diameter Gas side
(mm(in.)) Liquid side
Refrigerant type
Noise level (dB) (A-characteristic value) (*3)
External finish
Net weight
Indoor unit
External dimension
Temp. range of
cooling
Temp. range of
heating
(mm(in.))
Indoor
Outdoor
Indoor
Outdoor
kW (*1)
kcal/h (*2)
BTU/h (*1)
kW
A
m3/min
L/s
cfm
kg (lbs)
Total capacity
Model/Quantity
Height (H)
Width (W)
Depth (D)
W.B.
D.B.
D.B
W.B.
PURY-P450YGM-A PURY-P500YGM-A PURY-P550YGM-A PURY-P600YGM-A PURY-P650YGM-A
Heating Cooling Heating Cooling Heating Cooling Heating Cooling
56.0
56.0
63.0
63.0
67.0
67.4
75.0
73.0
–
50,000
–
55,000
–
60,000
–
65,000
191,100 191,100 215,000
230,000 255,900 249,100
Cooling
50.0
45,000
170,600
215,000 228,600
3N ~ 380/400/415V 50/60Hz
13.61
13.86
15.59
15.89
17.08
16.37
17.59
17.73
22.9/21.8/21.0 23.3/22.2/21.4 26.3/25.0/24.0 26.8/25.4/24.5 28.8/27.3/26.4 27.6/26.2/25.3 29.6/28.2/27.1 29.9/28.4/27.4
3.67
4.04
3.59
3.96
3.69
4.09
3.83
4.23
Salt Protected Fin
Inverter scroll hermetic compressor
Inverter
6.8 + 5.3
Propeller fan ✕ 1
8.2 + 5.3
9.3 + 5.3
Propeller fan ✕ 2
400
10.1 + 5.3
6,667
14,126
0.38 ✕ 2
High pressure switch 4.15MPa (601 psi)
Over-voltage and over-current protection for AC bus, Over-heat protection
Over-heat protection/Thermal switch
φ28.58(φ1-1/8") brazed
φ22.2(φ7/8") brazed
φ28.58(φ1-1/8") brazed
R410A
60/61 (50Hz/60Hz) 61/62 (50Hz/60Hz)
Pre-coated galvanized sheets + powder coating (for-BS type)
481(1061)
481(1061)
481(1061)
50~150% of outdoor unit capacity
481(1061)
Models P20~P250/1~24 Models P20~P250/1~24 Models P20~P250/1~24 Models P20~P250/1~32
1840(72-1/2")
1990(78-3/8")
840(33-1/8")
15~24˚C (59~75˚F)
-5~43˚C (23~109˚F) 0~43˚C (32~109˚F)(When the Outdoor is at a position lower than the Indoors)
15~27˚C (59~81˚F)
-20~15.5˚C (-4~60˚F)
Note: 1. Cooling/heating capacity indicates the maximum value at operation under the following condition.
*1 (JIS Standard: JIS B8615-1) Cooling 27˚C(81˚F)DB/19˚C(66.2˚F)WB Outdoor: 35˚C(95˚F)DB
Heating Indoor: 20˚C(68˚F)DB Outdoor: 7˚C(44.6˚F)DB/6˚C(42.8˚F)WB
Pipe length: 7.5m(24-9/16Ft) Height difference: 0m
PURY-P200,250,300,350YGM-A
Conn. pipe
(low pressure)
200:ø19.05
250:ø22.2
300:ø22.2
350:ø28.58
Conn. pipe
(high pressure)
A
57 80
200:ø15.88
250:ø19.05
300:ø19.05
350:ø19.05
65 160
494
B
768
Y
Y
Knockout hole
Cross section X–X
80
External Dimensions
ø27 Knockout hole
70 20
553
ø62 Knockout hole
Changeable to ø27,ø33 by using
attached conduit mounting plate
Air outlet
*2 Cooling Indoor: 27˚C(81˚F)DB/19.5˚C(67.1˚F)WB Outdoor: 35˚C(95˚F)DB
Pipe length: 5m(16-3/8Ft)
Height difference: 0m
2X2-14X20 0val hole
45 900(bolt hole) 45
990
Plane view
16
840
16 845(bolt hole)
877
19.65
33.1/31.5/30.3
3.72
10.9 + 5.3
Heating
81.5
–
278,100
19.82
33.4/31.7/30.6
4.11
62/62.5 (50Hz/60Hz)
481(1061)
Models P20~P250/1~32
*3 It is measured in anechoic room.
Unit : mm
265
Model A B
200 145 115
250 135 120
300 135 120
350 145 120
ø53
19
12 5
Cross section Y–Y
[Accessories]
• Refrigerant (high pressure) conn. pipe..............1pc.
• Refrigerant (low pressure) conn. pipe................1pc.
(The connecting pipe has been fixed with the unit)
• Packing for conn. low pressure pipe..................1pc.
(Attached near the ball valve)
• Conduit mouting plate
ø33, ø27............................Each 1pc.
• Tapping screw M4.....................1pcs.
Air
inlet
10 90
37
117
Left side view
ø27 Knockout hole
80 40
117
Air
inlet
134 100
280
Knockout hole
Service panel
Refrig. service
valve (high pressure)
67 160
X
15
235
184
Refrig. service
100
valve(low pressure)
37
Knockout hole
67
83
207
Knockout hole
Front view
207
67
X
78
11
1575
1840

OUTDOOR UNIT
Specifications & External Dimensions
R2 SERIES
R410A
External Dimensions
PURY-P400YGM-A
644
Unit : mm
81
1200(bolt hole) 45
1290
Plane view
840
16 845(bolt hole)
877
15
184
494
1000
553
840
845(bolt hole) 16
877
145
57 80
Conn. pipe
(low pressure)
ø28.58
65 160
145
768
Conn. pipe
(high pressure)
450:ø22.2
500:ø22.2
550:ø28.58
600:ø28.58
650:ø28.58
70 20
3X2-14X20 Oval hole
45
950(bolt hole)
1990
Plane view
950(bolt hole) 45
ø53
16
Knockout hole
145
80
57
Conn. pipe
(low pressure)
ø28.58
65 160
1068
Cross section X–X
Conn. pipe
(high pressure)
ø22.2
Y
Y
80
70 20
ø27 Knockout hole
503
ø62 Knockout hole
Changeable to ø46,ø53 by using
attached conduit mounting plate
Air outlet
2X2-14X20 Oval hole
45
12
5
ø53
Cross section Y–Y
[Accessories]
• Refrigerant (high pressure) conn. pipe........... 1pc.
(The connecting pipe has been fixed with the unit)
• Refrigerant (low pressure) conn. pipe............. 1pc.
(The connecting pipe has been fixed with the unit)
• Packing for conn. high pressure pipe.............. 1pc.
(Attached near the ball valve)
• Packing for conn. low pressure pipe............... 1pc.
(Attached near the ball valve)
• Conduit mouting plate
ø53, ø46................... Each 1pc.
• Tapping screw M4............ 2pcs.
Air
inlet
89
10
135
40
37 115 115 37
Left side view
80
Air
inlet
ø27 Knockout hole
134 100
280
Knockout hole
Service panel
Refrig. service
valve (high pressure)
235
Refrig. service
valve(low pressure)
Knockout hole
X
100
67 160
68
83
355
Knockout hole
Front view
355
68
X
11 78
1575 265
1840
PURY-P450,500,550,600,650YGM-A
Knockout hole
Y
Y
ø27 Knockout hole
Y
Y
ø62 Knockout hole
80
Changeable to ø46,ø53 by using
attached conduit mounting plate
Cross section X–X
Air outlet
16
265
12 5
Cross section Y–Y
[Accessories]
• Refrigerant (high pressure) conn. pipe.......... 1 pc.
(The connecting pipe has been fixed with the unit)
• Refrigerant (low pressure) conn. pipe............ 1 pc.
(The connecting pipe has been fixed with the unit)
• Packing for conn. high pressure pipe............. 1 pc.
(Attached near the ball valve)
• Packing for conn. low pressure pipe.............. 1 pc.
(Attached near the ball valve)
• Conduit mouting plate
ø53, ø46..................... Each 1 pc.
• Tapping screw M4.............. 2 pcs.
Air
inlet
10 89
37
115
Left side view
135
80 40
115
Air
inlet
ø27 Knockout hole
100
134
280
Knockout hole
Service panel
Refrig. service
valve (high pressure)
Knockout hole X
235
44
150
67 160
Refrig. service
valve(low pressure) 100 90
37
Knockout hole
68 205 290 260
260 290 205 68
Front view
78
11
1575
X
1840
20

HEAT SOURCE UNIT
Specifications & External Dimensions
WY SERIES
R410A
Model name
Capacity
Power source
Power input
Current
COP
Compressor
Heat
exchanger
Type
Motor output
Type
Water volume in the coil
Circulating Volume
water
Pressure drop
Refrigerant
External finish
Height(H)
External dimension Width(W)
Depth(D)
Protection
devices
High pressure protection
Compressor
Inverter
Gas/Liquid
Total capacity
Model / Quantity
Refrigerant piping diameter
Indoor
unit
Noise level
Net weight
Operating temperature range
kW
BTU/h
kW
A
kW
R
m3/h
cfh
kPa
mm(in.)
dB
kg(lbs.)
PQHY-P200YGM-A
Cooling
22.4
76,400
4.79
8.0/7.6/7.4
4.68
107,500 153,500
3N~380/400/415V 50/60Hz
Inverter scroll hermetic compressor
Galvanized sheets
1,800(70-7/ 8")
990(39") 1,980(78")
550(21-11/ 16")
High pressure switch 4.15 MPa (601psi)
Over-heat protection
Over-voltage and over-current protection for AC bus, Over-heat protection
ø9.52 flare / ø19.05 Flange ø9.52 flare /ø22.2 Flange ø12.7 flare / ø28.58 Flange ø15.88 flare / ø28.58 Flange
50%~130% of heat sourse unit capacity
Indoor:15˚CWB~24˚CWB
Water :10˚C~45˚C
5.0
Double coil
9.5
4.56
161
16.5
R410A
Heating
25.0
85,300
4.69
7.9/7.5/7.2
5.33
Model P20~250/1~13
46
272(600)
Indoor:15˚CDB~27CDB
Water :10˚C~45˚C
Specifications
PQHY-P250YGM-A
Cooling
28.0
95,500
5.95
10.0/9.5/9.1
4.71
Indoor:15˚CWB~24˚CWB
Water :10˚C~45˚C
6.0
Double coil
10.5
5.76
203
19.5
R410A
Heating
31.5
5.80
9.7/9.3/8.9
5.43
Model P20~250/1~16
47
275(607)
Note: 1.Cooling/Heating capacity indicates the maximum value at operation under the following condition.
Cooling Indoor:27˚C(80.6˚F)DB/19˚CWB
Water temperature: 30˚C(80˚F)
Heating Indoor:20˚C(68˚F)DB
Water temperature:20˚C(68˚F)
Pipe length:7.5m(24-9/16Ft) Height difference:0m
2.The ambient temperature of heat source unit has to be kept below 40˚C(104˚F)(dry bulb).
The ambient relative humidity of heat source unit has to be kept below 80%.
3.This unit can not be installed in the outdoor.(No protection against the weather.)
4.It is measured in anechoic room.
5.When the total capacity of indoor units exceeds 130% of heat source units capacity,
the operating temperature range of circulating water is 15˚C(59˚F)~45˚C(113˚F)
Indoor:15˚CDB~27˚CDB
Water :10˚C~45˚C
PQHY-P400YSGM-A
Cooling
45.0
11.35
19.1/18.2/17.5
3.96
Indoor:15˚CWB~24˚CWB
Water :10˚C~45˚C
9.7
Double coil
17.5
9.12
322
16.5
R410A
Heating
50.0
170,600
11.01
18.5/17.6/17.0
4.54
Model P20~250/1~22
50
208+244(459+538)
Indoor:15˚CDB~27˚CDB
Water :10˚C~45˚C
PQHY-P500YSGM-A
Cooling
56.0
191,100
15.06
25.4/24.2/23.3
3.72
Indoor:15˚CWB~24˚CWB
Water :10˚C~45˚C
11.6
Double coil
19.5
11.52
407
19.5
R410A
Heating
63.0
215,000
13.60
22.9/21.8/21.0
4.63
Model P20~250/1~24
53
208+248(459+547)
Indoor:15˚CDB~27˚CDB
Water :10˚C~45˚C
PQHY-P200,P250YGM-A
ø38 Knockout hole
Water outlet
(PT1 1/2 screw)
ø62 Knockout hole
924
415
255
140
126
94
50
ø38 Knockout hole
Water inlet
(PT1 1/2 screw)
ø40
126
95
ø27 Knockout hole
1397
1497
1579
415
255
1598
1626
A
B
External Dimensions
990
45 900(mounting pitch)
45
Note 1
Water inlet
(PT1 1/2 screw)
495
Note 1
Water outlet
(PT1 1/2 screw)
256 ø70
154
123
ø38 Knockout hole
206
318
ø27 Knockout hole
568
Plane view
69
Conn. pipe
200:ø9.52
250:ø9.52
Conn. pipe
200:ø19.05
250:ø22.2
Refrig. service valve
Refrig. service valve
Knockout hole
Drain
(PT1 screw)
2X2-14X20 Oval hole
(mounting hole)
550
570(mounting pitch)
602
16
1590
1772
(1800)
939
879
108
78
ø27 Knockout hole
ø38 Knockout hole
Piping space
(left side pipe)
Piping space
(left side pipe)
400
Fig. A
Note 2
Drain(PT1 screw)
Plane view
Service space
(front side)
Front view
400 600
Piping space
(upside pipe)
21
[Accessories]
• Refrigerant conn. pipe........... 1pc.
• Packing for conn. pipe.................... 1pc.
(Attached near the ball valve)
• Bushing......................................... 2pcs.
495
Model A B
Left side view Front view Right side view Rear view
P200 1346 1289
P250 1346 1299
127
182
Note 1. At the time of product shipment, the front side piping specification serves as the local drainage connection. When connecting on the rear side, please remove the rear side plug
sealing corks, and attach to a front side. Ensure there is no leak after the attachment has been fitted.
2. Take notice of service space as Fig. A (In case of single setting, 600mm or more of back space as front space makes easier access when servicing the unit from the rear side.)
3. In case the temperature around the heat source unit has possibility to drop under 0°C, be careful for the following point to prevent the pipe burst by the water pipe freeze-up.
• Circulate the water all the time even if the heat source unit is not in operation.
• Drain the water from inside of the heat source unit when the heat source unit will not operate for a long term.

HEAT SOURCE UNIT
Specifications & External Dimensions
WY SERIES
R410A
PQHY-P400,P500YSGM-A
External Dimensions
2X2-14X20 Oval hole
(mounting hole)
418
272
126
990
45 900(mounting pitch)
Water inlet
(PT2 screw)
1990
10
990
900(mounting pitch)
Water outlet
(PT2 screw)
69
154
45
2X2-14X20 Oval hole
(mounting hole)
550
570(mounting pitch)
602
Piping space
(left side pipe)
400
Plane view
Service space
(front side)
Piping space
(upside pipe)
600
400
418
ø70
143
233
ø56
719
318
Plane view
568
16
ø38 Knockout hole
ø27 Knockout hole
Front view
Piping space
(left side pipe)
Fig. A
272
Water outlet
(PT2 screw)
Water inlet
(PT2 screw)
76
131
1599
(1800)
Heat exchanger unit
Conn. pipe
P400:ø28.58
P500:ø28.58
Conn. pipe
P400:ø12.7
P500:ø15.88
Refrig. service valve
Compressor unit
Knockout hole
1590
1772
78
108
ø27 Knockout hole
Knockout hole
126
660
950
624
585
Refrig. service
valve
Drain
(PT1 screw)
127
182
939
879
ø38 Knockout hole
Left side view
[Accessories]
• Refrigerant conn.pipe.............................................. 1pc.
(The connecting pipe is fixed with the unit)
• Refrigerant conn.pipe........................................... 1pc.
(Packaged in the accessory kit)
• Refrigerant conn.pipe between HEX unit and Compressor unit
ø9.52................................................................................ 2pcs.
(Packaged in the accessory kit)
ø19.05.............................................................................. 2pcs.
(Packaged in the accessory kit)
ø25.4................................................................................ 2pcs.
(Packaged in the accessory kit : HEX unit)
(The connecting pipe is fixed with the unit : Compressor unit)
• Packing for conn.pipe....................................................... 4pcs.
(Attached near the ball valve)
• Bushing............................................................................. 6pcs.
• Extension code for water heat source............................... 1set
Drain
(PT1 screw)
Front view
Locally piping
ø9.52
ø19.05
ø25.4
Conn.pipe between HEX unit
and Compressor unit
(Extension code for water heat source)
Control signal wire
Right side view
Note 1. At the time of product shipment, the front side piping specification serves as the local drainage connection. When connecting on the rear side, please remove the rear side plug sealing corks, and attach to a front side. Ensure
there is no leak after the attachment has been fitted.
2. Take notice of service space as Fig. A (In case of single setting, 600mm or more of back space as front space makes easier access when servicing the unit from the rear side.)
3. In case the temperature around the heat source unit has possibility to drop under 0°C, be careful for the following point to prevent the pipe burst by the water pipe freeze-up.
• Circulate the water all the time even if the heat source unit is not in operation.
• Drain the water from inside of the heat source unit when the heat source unit will not operate for a long term.
4. Use the extension code for water heat source (option) to take space (more than 2m) between HEX unit Compressor unit.
22

HEAT SOURCE UNIT
Specifications & External Dimensions
WR2 SERIES
Model name
Capacity
Power source
Power input
Current
COP
Compressor
Heat
exchanger
R410A
Type
Motor output
Type
Water volume in the coil
Circulating Volume
water
Pressure drop
Refrigerant
External finish
Height(H)
External dimension Width(W)
Depth(D)
Protection
devices
High pressure protection
Compressor
Inverter
gas / Liquid
Refrigerant piping diameter
indoor Total capacity
unit Model / Quantity
Noise level
Net weight
Operating temperature range
kW
BTU/h
kW
A
kW
R
m3/h
cfh
kPa
mm(in.)
dB
kg(lbs)
PQRY-P200,P250YGM-A
PQRY-P200YGM-A
Cooling
22.4
76,400
4.79
8.0/7.6/7.4
4.68
5.0
Double coil
9.5
4.56
161
16.5
R410A
Heating
25.0
85,300
4.69
7.9/7.5/7.2
5.33
Specifications
107,500 153,500
3N~380/400/415V 50/60Hz
Inverter scroll hermetic compressor
Galvanized sheets
1,800(70-7/ 8 ")
990(39") 1,980(78")
550(21-11/ 16 ")
High pressure switch 4.15 MPa (601psi)
Over-heat protection
Over-voltage and over-current protection for AC bus, Over-heat protection
ø15.88 flare / ø19.05 Flange ø19.05 flare /ø22.2 Flange ø22.2 flare / ø28.58 Flange ø22.2 flare / ø28.58 Flange
50%~150% of heat sourse unit capacity
Model P20~250/1~15
46
263(580)
Indoor:15˚CWB~24˚CWB
Water :10˚C~45˚C
Indoor:15˚CDB~27CDB
Water :10˚C~45˚C
PQRY-P250YGM-A
Cooling
28.0
95,500
5.95
10.0/9.5/9.1
4.71
Indoor:15˚CWB~24˚CWB
Water :10˚C~45˚C
6.0
Double coil
10.5
5.76
203
19.5
R410A
Heating
31.5
5.8
9.7/9.3/8.9
5.43
Model P20~250/1~19
47
266(587)
Note: 1.Cooling/Heating capacity indicates the maximum value at operation under the following condition.
Cooling Indoor:27˚C(80.6˚F)DB/19˚CWB
Water temperature: 30˚C(80˚F)
Heating Indoor:20˚C(68˚F)DB
Water temperature:20˚C(68˚F)
Pipe length:7.5m(24-9/16Ft) Height difference:0m
2.The ambient temperature of heat source unit has to be kept below 40˚C(104˚F)(dry bulb).
The ambient relative humidity of heat source unit has to be kept below 80%.
ø38 Knockout hole
Water outlet
(PT1 1/2 screw)
ø62 Knockout hole
924
415
255
140
126
94
50
ø38 Knockout hole
Water inlet
(PT1 1/2 screw)
1397
1497
1579
415
255
1598
1626
ø40
126
95
ø27 Knockout hole
A
B
256
495
123
206
318
568
69
Indoor:15˚CDB~27˚CDB
Water :10˚C~45˚C
External Dimensions
990
45 900(mounting pitch)
45
Note 1 Water inlet
(PT1 1/2 screw)
Note 1 Water outlet
(PT1 1/2 screw)
ø70
154
550
570(mounting pitch)
602
ø38 Knockout hole
ø27 Knockout hole
Plane view
Conn. pipe
200:ø15.88
250:ø19.05
Conn. pipe
200:ø19.05
250:ø22.2
Refrig. service valve
Refrig. service valve
Knockout hole
Drain
(PT1 screw)
16
1590
1772
(1800)
PQRY-P400YSGM-A
Cooling
45.0
11.35
19.1/18.2/17.5
3.96
Indoor:15˚CWB~24˚CWB
Water :10˚C~45˚C
9.7
Double coil
17.5
9.12
322
16.5
R410A
Heating
50.0
170,600
11.01
18.5/17.6/17.0
4.54
Model P20~250/1~24
50
208+232(459+512)
Indoor:15˚CDB~27˚CDB
Water :10˚C~45˚C
PQRY-P500YSGM-A
Cooling
56.0
191,100
15.06
25.4/24.2/23.3
3.72
Indoor:15˚CWB~24˚CWB
Water :10˚C~45˚C
11.6
Double coil
19.5
11.52
407
19.5
R410A
Heating
63.0
215,000
13.6
22.9/21.8/21.0
4.63
Model P20~250/1~24
53
208+236(459+521)
Indoor:15˚CDB~27˚CDB
Water :10˚C~45˚C
3.This unit can not be installed in the outdoor.(No protection against the weather.)
4.It is measured in anechoic room.
5.When the total capacity of indoor units exceeds 130% of heat source units capacity,
the operating temperature range of circulating water is 15˚C(59˚F)~45˚C(113˚F)
2X2-14X20 Oval hole
(mounting hole)
939
879
ø27 Knockout hole
78
ø38 Knockout hole
Piping space
(left side pipe)
Piping space
(left side pipe)
400
Plane view
Service space
(front side)
Front view
Fig. A
Note 2
Drain(PT1 screw)
400 600
Piping space
(upside pipe)
23
[Accessories]
• Refrigerant conn. pipe.......... 1pc.
(The connecting pipe is fixed with the unit)
• Refrigerant conn. pipe......... 1pc.
(Packaged in the accsessory kit)
• Packing for conn. pipe.................................... 1pc.
(Attached near the ball valve)
• Bushing......................................................... 2pcs.
495
Model A B
Left side view Front view Right side view Rear view
P200 1347 1289
P250 1342 1299
127
182
Note 1. At the time of product shipment, the front side piping specification serves as the local drainage connection. When connecting on the rear side, please remove the rear side plug
sealing corks, and attach to a front side. Ensure there is no leak after the attachment has been fitted.
2. Take notice of service space as Fig. A (In case of single setting, 600mm or more of back space as front space makes easier access when servicing the unit from the rear side.)
3. In case the temperature around the heat source unit has possibility to drop under 0°C, be careful for the following point to prevent the pipe burst by the water pipe freeze-up.
• Circulate the water all the time even if the heat source unit is not in operation.
• Drain the water from inside of the heat source unit when the heat source unit will not operate for a long term.

HEAT SOURCE UNIT
Specifications & External Dimensions
WR2 SERIES
R410A
PQRY-P400,P500YSGM-A
External Dimensions
126
990
45 900(mounting pitch)
Water inlet
2X2-14X20 Oval hole (PT2 screw)
(mounting hole)
418
272
1990
10
990
900(mounting pitch)
Water outlet
(PT2 screw)
69
154
45
2X2-14X20 Oval hole
(mounting hole)
550
570(mounting pitch)
602
Piping space
(left side pipe)
Plane view
Service space
(front side)
Piping space
400
(upside pipe)
600
400
418
ø70
143
233
ø56
719
318
Plane view
568
16
ø38 Knockout hole
ø27 Knockout hole
Front view
Piping space
(left side pipe)
Fig. A
272
Water outlet
(PT2 screw)
Water inlet
(PT2 screw)
76
131
1599
(1800)
Heat exchanger unit
Conn. pipe
ø28.58
Conn. pipe
ø22.2
Refrig.
service valve
Compressor unit
Knockout hole
1590
1772
78
108
ø27 Knockout hole
Knockout hole
126
Left side view
[Accessories]
• Refrigerant conn.pipe....................................................... 2pcs.
(The connecting pipe is fixed with the unit)
• Refrigerant conn.pipe between HEX unit and Compressor unit
ø9.52................................................................................ 2pcs.
(Packaged in the accessory kit)
ø19.05.............................................................................. 2pcs.
(Packaged in the accessory kit)
ø25.4................................................................................ 2pcs.
(Packaged in the accessory kit : HEX unit)
(The connecting pipe is fixed with the unit : Compressor unit)
• Packing for conn.pipe....................................................... 4pcs.
(Attached near the ball valve)
• Bushing............................................................................ 2pcs.
• Extension code for water heat source............................... 1set
660
950
648
585
Refrig.
service
valve
Drain
(PT1 screw)
Front view
Locally piping
ø9.52
ø19.05
ø25.4
Drain
(PT1 screw)
127
182
Conn.pipe between HEX unit
and Compressor unit
(Extension code for water heat source)
Control signal wire
939
879
Right side view
ø38 Knockout hole
Note 1. At the time of product shipment, the front side piping specification serves as the local drainage connection. When connecting on the rear side, please remove the rear side plug sealing corks, and attach to a front side. Ensure
there is no leak after the attachment has been fitted.
2. Take notice of service space as Fig. A (In case of single setting, 600mm or more of back space as front space makes easier access when servicing the unit from the rear side.)
3. In case the temperature around the heat source unit has possibility to drop under 0°C, be careful for the following point to prevent the pipe burst by the water pipe freeze-up.
• Circulate the water all the time even if the heat source unit is not in operation.
• Drain the water from inside of the heat source unit when the heat source unit will not operate for a long term.
4. Use the extension code for water heat source (option) to take space (more than 2m) between HEX unit and Compressor unit.
24

BC CONTROLLER
Specifications & External Dimensions
BC Controller for
R2/WR2 SERIES
R410A
CMB-P-V-G
CMB-P-V-GA
CMB-P-V-GB
Model name
Number of branch
Power source
Power input
Current
External finish
Indoor unit capacity
connectable to 1 branch *
Conncctable Outdoor unit
Height
Width
Depth
Refrigerant
piping
diameter
Drain pipe
Net weight
Accessories
To outdoor
unit
To indoor
unit
To another
BC controller
50Hz
kW
60Hz
A
50Hz
60Hz
mm
mm
mm
High pressure
pipe
Low pressure
pipe
Liquid pipe
Gas pipe
Low press gas
pipe
High press gas
pipe
Liquid pipe
Cooling
heating
Cooling
heating
Cooling
heating
Cooling
heating
Specifications
CMB-P-V-GB
CMB-P104V-G CMB-P105V-G CMB-P106V-G CMB-P108V-G CMB-P1010V-G CMB-P1013V-G CMB-P1016V-G CMB-P108V-GA CMB-P1010V-GA CMB-P1013V-GA CMB-P1016V-GA CMB-P104V-GB CMB-P108V-GB
4 5 6 8 10 13 16 8 10 13 16 4 8
~220/230/240V 50Hz/60Hz
~220/230/240V 50Hz/60Hz
0.067/0.076/0.085 0.082/0.093/0.104 0.097/0.110/0.123 0.127/0.144/0.161 0.156/0.177/0.198 0.201/0.288/0.255 0.246/0.279/0.312 0.127/0.144/0.161 0.156/0.177/0.198 0.201/0.228/0.255 0.246/0.279/0.312 0.060/0.068/0.076 0.119/0.135/0.151
0.030/0.034/0.038 0.038/0.043/0.048 0.045/0.051/0.057 0.060/0.068/0.076 0.075/0.085/0.095 0.097/0.110/0.123 0.119/0.135/0.151 0.060/0.068/0.076 0.075/0.085/0.095 0.097/0.110/0.123 0.119/0.135/0.151 0.030/0.034/0.038 0.060/0.068/0.076
0.054/0.061/0.067 0.066/0.074/0.082 0.078/0.088/0.097 0.102/0.115/0.127 0.126/0.141/0.156 0.162/0.182/0.201 0.198/0.222/0.246 0.102/0.115/0.127 0.126/0.141/0.156 0.162/0.182/0.201 0.198/0.222/0.246 0.048/0.054/0.060 0.096/0.108/0.119
0.024/0.027/0.030
0.31/0.34/0.36
0.14/0.15/0.16
0.25/0.27/0.28
0.11/0.12/0.13
0.030/0.034/0.038
0.38/0.41/0.44
0.18/0.19/0.20
0.30/0.33/0.35
0.14/0.15/0.16
0.036/0.041/0.045
0.45/0.48/0.52
0.21/0.23/0.24
0.36/0.39/0.41
0.17/0.18/0.19
0.048/0.054/0.060
0.58/0.63/0.68
0.28/0.30/0.32
0.47/0.50/0.53
0.22/0.24/0.25
0.060/0.068/0.075
0.71/0.77/0.83
0.35/0.37/0.40
0.58/0.62/0.65
0.28/0.30/0.32
Galvanizing
Model P140 or smaller
PURY-P200, 250, 300, 350YGM-A
284
648
432
For P200 type: ø15.88 Brazed
For P250, P300, P350 type: ø19.05 Brazed
For P200 type: ø19.05 Brazed
For P250, P300 type: ø22.2 Brazed
For P350 type: ø28.58 Brazed
ø9.52 Flare
(ø6.35 with attached reducer used, ø12.7 with optional joint pipe used)
ø15.88 Flare
(ø12.7 with attached reducer used, ø19.05 with optional joint pipe used)
•Drain connection pipe (with flexible hose and insulation)
•Reducer
1098
Galvanizing
Model P140 or smaller
PURY-P200~650YGM-A *2
289
1110
520
For P200 type: ø15.88 Brazed
For P250, P300, P350 type: ø19.05 Brazed
For P400 to P500 type: ø22.22 Brazed
For P550 to P650 type: ø28.58 Brazed
For P200 type: ø19.05 Brazed
For P250, P300 type: ø22.2 Brazed
For P350 to P650 type: ø28.58 Brazed
ø9.52 Flare
CMB-P108V~P1016V-GA
284
648
432
(ø6.35 with attached reducer used, ø12.7 with optional joint pipe used)
ø15.88 Flare
(ø12.7 with attached reducer used, ø19.05 with optional joint pipe used)
For total capacity below P200 type: ø19.05 Brazed
-
For total capacity below P201 to P300 type: ø22.2 Brazed
For total capacity below P301 to P350 type: ø28.58 Brazed
For total capacity below P200 type: ø15.88 Brazed
-
For total capacity below P201 to P350 type: ø19.05 Brazed
For total capacity below P300 type: ø9.52 Brazed
-
For total capacity below P301 to P350 type: ø12.7 Brazed
VP-25
VP-25
24 27 29 34 39 47 54 44 49 57 64 22 32
*1 Use optional joint pipe combining 2-branch when the total unit capacity exceeds P140.
Use the reducer (standard accessory) when the indoor unit Model P50 or smaller is connected.
CMB-P104,105,106,108,
1010,1013V-G
Drain piping
VP-25 connection
181
64
130
Connnection pipe of outdoor unit
(High pressure)
200: ø15.88 (with accessory)
250, 300, 350: ø19.05
103
64
23
248
Connection pipe of outdoor unit (Low pressure)
200: ø219.05 (with accessory)
250, 300: ø22.2
350: ø28.58 (with accessory)
284
255
128
X
58
27
Y
200
70
• Refrigerant conn. pipe (Large, Small).....2pc
• Refrigerant conn. pipe............................1pc
• Reducer (Large, Small)..................Quantity for all connection
• Drain hose (VP-25 connection)..........................................1pc
• Pipe cover for drain hose...................................................1pc
• Hose band..........................................................................1pc
• Tie band.............................................................................1pc
Band (accessory)
Drain hose (Accessory)
ø31
Detail of X section
76 60XC=D
60
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
A
B (Lifting bolt pitch)
30
12
Control box
14
Detail of Y section
0.078/0.088/0.097
0.92/1.00/1.07
0.45/0.48/0.52
0.74/0.80/0.84
0.36/0.39/0.41
External Dimensions
Note 1. Suspesion bolt (ø10), washer (M10) and
nut (M10) prepare in the field.
2. Take notice of service space as follows;
(Please give attention not to occupy service
space by letting ducts and pipes through)
In the following, Access door in service space
is a door for service. There fore, another door
is necessary to unload products.
CMB-P104V-G
CMB-P105V-G
CMB-P106V-G
CMB-P108V-G
CMB-P1010V-G
CMB-P1013V-G
CMB-P1016V-G
70
298 (Lifting bolt pitch)
362
Connection pipe of
indoor unit (Liquid)
ø9.52 (Flare)
(200)
Connection pipe of
indoor unit (Gas)
ø15.88 (Flare)
Service
space
A
648
1098
B
702
1152
Access door
450
C
3
4
5
7
9
12
15
200
180
240
300
420
540
720
900
250
D
(700)
0.096/0.108/0.119
1.12/1.22/1.30
0.55/0.59/0.63
0.90/0.97/1.03
0.44/0.47/0.50
0.048/0.054/0.060
0.58/0.63/0.68
0.28/0.30/0.32
0.47/0.50/0.53
0.22/0.24/0.25
0.060/0.068/0.075
0.71/0.77/0.83
0.35/0.37/0.40
0.58/0.62/0.65
0.28/0.30/0.32
0.078/0.088/0.097
0.92/1.00/1.07
0.45/0.48/0.52
0.74/0.80/0.84
0.36/0.39/0.41
0.096/0.108/0.119
1.12/1.22/1.30
0.55/0.59/0.63
0.90/0.97/1.03
0.44/0.47/0.50
0.024/0.027/0.030
0.28/0.30/0.32
0.14/0.15/0.16
0.22/0.24/0.25
0.11/0.12/0.13
0.048/0.054/0.060
0.55/0.59/0.63
0.28/0.30/0.32
0.44/0.47/0.50
0.22/0.24/0.25
•Drain connection pipe (with flexible hose and insulation)
•Reducer
*2 Additional pipework is needed to connect with P300 type or lower outdoor unit.
ø31
Connnection pipe of
MASTER BC CONTROLLER (High pressure)
Total capacity of indoor unit.
For 200 or less: ø15.88
(with accessory)
For 201 or over: ø19.05
Drain piping
VP-25 connection
CMB-P104,108V-GB
Band (accessory)
Drain hose (Accessory)
181
Connnection pipe of
MASTER BC CONTROLLER
(Low pressure)
Total capacity of indoor unit.
For 200 or less: ø19.05
(with accessory)
From 201 to 300: ø22.2
For 301 or over: ø28.58
(with accessory)
Detail of X section
64
130
• Reducer.....Quantity for all connections
• Drain hose (VP-25 connection).......1pc
• Pipe cover for drain hose.................1pc
• Hose band.......................................1pc
• Tie band...........................................2pc
64
45
103
169
23
284
255
248
30
128
12
X
58
27
Y
14
Detail of Y section
Connnection pipe of
MASTER BC CONTROLLER (Liquid)
Total capacity of indoor unit.
For 300 or less: ø9.52
For 301 or over: ø12.7 (with accessory)
70
76
60
Control box
648
702 (Lifting bolt pitch)
60XA=B
1 2 3 4 5 6 7 8
A B
CMB-P104V-GB 3 180
CMB-P108V-GB 7 420
298 (Lifting bolt pitch)
70
362
(200)
Connection pipe of
indoor unit (Liquid)
ø9.52 (Flare)
Unit : mm
Note 1. Suspesion bolt (ø10), washer (M10)
and nut (M10) prepare in the field.
2. Take notice of service space as follows;
(Please give attention not to occupy service
space by letting ducts and pipes through)
In the following, Access door in service
space is a door for service. There fore, another
door is necessary to unload products.
3. Can't use singleness.
(MASTER BC CONTROLLER is necessary.)
Access door
450
Service space
200
(700)
250
CMB-P108,1010,1013,1016V-GA
Drain piping
VP-25 connection
333
64
64 103
268
Connnection pipe of
outdoor unit (High pressure)
For P200 type: ø15.88 Brazed
For P250, P300 type: ø19.05 Brazed
For P350 type: ø22.22 Brazed
For P400 to P650 type: ø28.58 Brazed
Y
X
Band (accessory)
Drain hose (Accessory)
1110
130 23
ø31
Detail of X section
Control box
30
12
450 70
14
Detail of Y section
388 (Lifting bolt pitch)
268
210
103
66
128
74
200
Connection pipe of
SUB BC CONTROLLER (High pressure)
Total capacity of indoor unit
For 200 or less: ø15.88 (with accessory)
For 201 or over: ø19.05
Connection pipe of
SUB BC CONTROLLER (Liquid)
Total capacity of indoor unit
For 300 or less: ø9.52
For 301 or over: ø12.7 (with accessory)
Connection pipe of
SUB BC CONTROLLER (Low pressure)
Total capacity of indoor unit
For 200 or less: ø19.05 (with accessory)
From 201 to 300: ø22.2
For 301 or over: ø28.58 (with accessory)
Connection pipe of
indoor unit (Gas)
ø15.88 (Flare)
• Refrigerant conn. pipe...............1pc
• Refrigerant conn. pipe..............1pc
• Reducer (Large, Small).....Quantity for all connection
• Drain hose (VP-25 connection)............................1pc
• Hose band............................................................1pc
• Tie band...............................................................1pc
Note 1. Suspesion bolt (ø10), washer (M10) and nut (M10) prepare
in the field.
2. Take notice of service space as follows:
(Please give attention not to occupy service space by letting
ducts and pipes through)
In the following, Access door in service space is a door for
service. There fore, another door is necessary to unload products.
3. Please take space to connect SUB BC CONTROLLER.
25
Connection pipe of outdoor unit
(Low pressure)
For P200 type: ø19.05 Brazed
For P250, P300 type: ø22.2 Brazed
For P350 type: ø28.58 Brazed
For P400 to P650 type: ø28.58 Brazed
289
260
128
74
27
90 76
60
1 2
70
3
4
5
1164 (Lifting bolt pitch)
60XA=B
6 7 8 9 10 11 12 13 14 15 16
Connection pipe of indoor unit (Liquid)
ø9.52 (Flare)
70
Connection pipe of
indoor unit (Gas)
Service
space
Access door
450
200
200
250
700
CMB-P108V-GA
CMB-P1010V-GA
CMB-P1013V-GA
CMB-P1016V-GA
A
7
9
12
15
B
420
540
720
900
200
ø15.88 (Flare)
200

Wide selection of indoor units
Ceiling cassette (4way air flow)
PLFY-P VCM-E
PLFY-P VAM-E
Ceiling suspended
Model
Capacity
P20 P25 P32 P40 P50 P63 P80 P100 P125
2.2kW 2.8kW 3.6kW 4.5kW 5.6kW 7.1kW 9.0kW 11.2kW 14.0kW
PCFY-P VGM-E
Model P40 P63 P100 P125
Capacity 4.5kW 7.1kW 11.2kW 14.0kW
Ceiling cassette (2way air flow)
PLFY-P VLMD-E
Wall mounted
PKFY-P VAM-E
PKFY-P VGM-E
PKFY-P VFM-E
Model
P20 P25 P32 P40 P50 P63 P71 P80 P100 P125
Model
P20 P25 P32
P40
P50
P63
P100
Capacity 2.2kW 2.8kW 3.6kW 4.5kW 5.6kW 7.1kW 8.0kW 9.0kW 11.2kW 14.0kW
Capacity
2.2kW 2.8kW 3.6kW
4.5kW
5.6kW
7.1kW
11.2kW
Ceiling cassette (1way air flow)
Floor standing
New
PFFY-P VLEM-E
PFFY-P VKM-E
PMFY-P VBM-E
PFFY-P VLRM-E
Model
P20 P25 P32 P40
Model
P20 P25 P32 P40
P50
P63
Capacity
2.2kW 2.8kW 3.6kW 4.5kW
Capacity
2.2kW 2.8kW 3.6kW 4.5kW
5.6kW
7.1kW
Ceiling concealed
New
Fresh Air Intake
PEFY-P VMH-E-F
PEFY-P VMR-E-L/R
PEFY-P VMH-E
PEFY-P VMM-E
PEFY-P VML-E
New
PEFY-P VMS-E
Model P20 P25 P32 P40 P50 P63 P71 P80 P100 P125 P140 P200
P250
Model
P80
P140
P200
P250
Capacity 2.2kW 2.8kW 3.6kW 4.5kW 5.6kW 7.1kW 8.0kW 9.0kW 11.2kW 14.0kW 16.0kW 22.4kW 28.0kW
Capacity
9.0kW
16.0kW
22.4kW
28.0kW
26

INDOOR UNIT
Ceiling cassette type
4-way airflow
PLFY-P VCM-E/VAM-E
PLFY-P VCM-E
PLFY-P VAM-E
VCM
VAM
The new compact cassette VCM is suitable for 2x2 ceiling!
compact body to match with
2feets (600mm) x 2feets (600mm)
ceiling design (VCM)
570mm
570mm
Easy Installation
Superb Features
Only two panel sizes–perfectly suited to
various installation configurations
Only two panel sizes are available,650mm(25-
5/8in.) for the compact VCM and 950mm(37-
7/16in.) for the power cassette VAM. The VCM is
lightweight min.15kg(34lbs)(P20/P25)
PLFY-VCM Type
PLFY-VAM Type
Drain water pipe lifted to 850mm(33- 1 /2in.)
(power cassette VAM)
The drain piping of the VAM can be
positioned anywhere up to 850mm(33- 1 /2in.)
from the ceiling's surface, allowing greater
freedom with long cross-piping and more
versatility with piping layouts
(VCM: 500mm(19- 11 /16in.)).
850mm
(33- 1 /2in.)
First in the industry to offer 72 airflow
patterns (power cassette VAM)
The 72 different airflow patterns provide the
best solution for varying room layouts and
air-conditioning requirements. For extra
versatility, you can also select from two-,
three- or four-way outlets. What's more, the
addition of separate motors to the individual
vanes enables manual control that-together
with remote control vane settings-make
possible highly customized and flexible
airflow patterns.
650mm
(25- 5 /8in.)
950mm
(37- 7 /16in.)
4-, 3-, or 2-
way outlet
selection
Unit height of only 208mm* 1 great for
low-ceiling space situations
The new compact cassette VCM has a unit
height of only 208mm *1 , to realize neat
installation in low-ceiling situations with very
limited space.
*:8- 1 /4in
(compact cassette VCM)
Only
208mm*!
Handy corner-pocket design simplifies maintenance
and installation (power cassette VAM)
By using the handy corner pockets equipped
on four corners of the grille, maintenance
work such as drain pan cleaning and height
adjustment can be accomplished without
removing the grille. It is also easier to adjust
the ceiling height of the indoor unit during
installation.
Fixed airflow
direction per
vane
Motor
for the
vane
72 airflow patterns
*Optional air outlet shutter plate is
necessary for two-or three-way airflow
settings. The noise level may increase
during two-or three-way airflow setup.
*For VCM model, 2 or 3 way airflow is
not available.
27

INDOOR UNIT
Ceiling cassette type
4-way airflow
PLFY-P VCM-E
PLFY-P VAM-E
Superb Features
Outstanding Specifications
For Retail Outlets
(Power cassette VAM)
These units are ideal for maintaining constant
temperatures in environments that have
equipment such as refrigerate showcases.
Individual vane angle adjustment enables
precise airflow control to specific areas of the
store to reduce unnecessary air conditioning
of areas such as refrigerated showcases.
Remote control setting for two directions
Fixed vane for two directions
Smudge-free airflow prevents soiling of the
ceiling surface (power cassette VAM )
Mitsubishi Electric has developed a new airflow
control mechanism where a projection inside the
air passage distributes air evenly over the vane's
upper and lower surface while two additional
projections at the air outlet's exit adjust the angle
of the airflow. This helps to prevent indoor air
from rising, stopping it from hitting the surface
of the ceiling to reduce the likelihood of soiling
from smudging and condensation.
Wide-flow air outlet delivers
a comforting breeze (VAM)
The airflow of the VAM power cassette is
powerful enough to warm atrium-type
ceilings up to 4.2 meter(13- 13 /16Ft) in height.
4-way high ceiling 2 (VAM)
4.2m
(13- 13 /16Ft)
4-way standard (VAM)
3.2m
(10- 1 /2Ft)
Fixed
Fixed
Smudging and the new
airflow control mechanism
3.6m
(11- 13 /16Ft)
Outside
Inside
3-way standard (VAM)
Fixed
Refrigerated
showcase not
affected by air
conditioning
Fixed
Top or bottom
airflow setting via
remote controller
Compatible with both round and square
ducts (power cassette VAM)
For easy connection to branch ducts,
knockout holes are designed to fit both round
and square ducts. Matching the shape of the
duct fringe provides more flexibility during
installation.
Connecting to round ducts
1
2 3
Grille
Wider airflow setting
reduces annoying drafts
30° horizontal
position
70° vertical
position
3
1
A projection is created on the outside, where the airflow is
fastest. This diverts the airflow and distributes it evenly
over the upper and lower surfaces of the Vane.
The air outlet exit also has projections to prevent air from rising
within the room and stopping it from hitting the ceiling.
30°
70°
2
Vane
Smudging:
When cooled air is
expelled horizontally, it
tends to cling to the
surface of the ceiling. This
cools the surface down
and causes condensation,
which attracts dust from
the room's interior to soil
the ceiling's surface.
Bristle-free vane can be cleaned simply
(power cassette VAM )
The unique suction mechanism prevents indoor
air from rising to eliminate condensation on the
vane and make bristles unnecessary.
Specifications according to ceiling height and number of vents
4-way
3-way
2-way
During operation
Power Cassette VAM
Standard High ceiling 1 High ceiling 2
3.2
3.6
4.0
3.6
4.0
4.2
4.2
4.2
---
*VCM:2.7m(standard/4way only)
Functional and appealing vane shutter
(power cassette VAM)
When the air conditioner is not operating, the
vane shutter closes automatically to conceal
the air outlet and create an aesthetically
appealing flat surface.*
*This feature will not activate when the vane is set at
fixed position.
When turned off
150mm(5- 15 /16in.) diameter cutout
Connecting to rectangular ducts
Direct intake of fresh exterior air
(power cassette VAM &compact cassette VCM)
Indoor air quality is significantly enhanced by
the direct intake of fresh exterior air. An
optional multi-function casement is also
available (only for VAM) for the intake of a
larger volume of air.
350mm(13- 13 /16in.)~100mm(3- 15 /16in.) cutout
28

INDOOR UNIT
Ceiling cassette type
2-way airflow
(drain-up mechanism is built in)
PLFY-P VLMD-E
PLFY-P VLMD-E
Slim body of 290 mm* height. (*11- 7 /16in.)
Slim body - only 290mm height
The slimline body is highly suitable for installation in narrow ceiling
spaces and for replacing obsolete air-conditioning equipment in older
buildings. The main unit is only 290mm* height.
290mm*
(*: 11- 7 /16in.)
Equipped with drain water lift-up
mechanism as standard
Terminal block on outside of main unit
makes wiring easier
The drain can be positioned anywhere up to 600mm* from the
ceiling's surface, providing greater freedom with long cross-piping
and allowing more versatility with piping layouts.(*: 23- 5 /8in.)
Main unit height - 290mm(11- 7 /16in.)
Drain height
max. 593mm(23- 3 /8in.)
Newly designed decorative panel with air flow
switching and swing functions as a standard feature
Ceiling surface
593
(unit: mm)
Compact unit and low noise level attained!
Fresh air directly taken in
Fresh air can be taken in to the main unit directly (optional accessories
needed.
29

INDOOR UNIT
Ceiling cassette type
1-way airflow
PMFY-P VBM-E
PMFY-P VBM-E
Compact and lightweight body perfect for
limited ceiling space applications.
Compact size for smooth
installation and maintenance
Unit body size has been standardized for all
models at 854mm for easier installation. Body
weight is also only 14kg for the main unit and
3kg for the panel, making this unit one of the
lightest in the industry.
Quiet operation
Newly developed airflow control technology
reduces noise level to only 27dB (P20VBM)
for industry-leading quiet operation.
Drain lift-up mechanism
The drain can be positioned anywhere up to 600mm* from the ceiling's surface.(*: 23- 5 /8in.)
max.
600*
230
(9- 11 /16)
PMFY-VBM
max.
402
(15- 7 /8)
198
(7- 13 /16)
unit: mm(in.)
30

INDOOR UNIT
Ceiling concealed
type
PEFY-P VMR-E-L/R
New
PEFY-P VMR-E-L/R
Problem solver for residential hotels, museums, libraries,
or hospitals where low noise is especially a must!
Inlet
Card Key
Switch
Noise measurement point
Noise measurement point
*According to the data measured in Mitsubishi Electric laboratory
Operable by card key switch
Ultra low noise
Prepared a contact for a card key. It’s possible
to operate / stop by taking a card key in and
out.
Enables to install for symmetric
design room
Both of Left piping / Right piping, control
box, are available.
It's selectable for layout of each room.
Plus easy maintenance from the access door
in the prefabricated bath.
*Seen from an anterior view, the pipe and
control box are on the right side of –R type.
Realizing the low level noise that is NC21 around a bed and N22 around a desk when the high
notch.
It contributes to create a quiet indoor environment.
*Outlet is elbow-constructed using a glass wool duct.
The noise level is changed by the room size or the setting condition of the unit.
Energy-saving by prevention of forgetting the switch off
Compact & Simple operation remote controller is available.
*This remote controller can operate only start / stop, Indoor temperature control and wind speed
control. Centralized remote controller must be used together.
Enables a prevention to forget the switch in a vacant room off by the centralized remote
controller like G-50.
31

INDOOR UNIT
Ceiling concealed
type
PEFY-P VMS-E
New
PEFY-P VMS-E
Increased design flexibility for the places where low noise
operation is especially needed from an ultra thin body.
Changeable static pressure
(4 stage 5-15-35-50Pa)
Ultra low height unit with 200mm high
Can be installed easily in tight spaces, such as ceiling cavities or drop-ceilings.
Changeable air flow rate
(3 stage low-middle-high)
Drain lift-up pump is attached
as standard.
Filter is attached as standard.
More than 20mm
More than 20mm
Ceiling surface Access door
Make the access door at the appointed position properly
for service maintenance.
unit: mm
Reduced noise thanks to the use of newly designed centrifugal fan and coil
Noise level table (Standard static pressure)
Noise
Level
Capacity
High
Fan
Speed
Mid
Low
P20
27
25
22
P25
27
25
22
dB(A)
P32
30
28
25
32

INDOOR UNIT
Ceiling concealed
type
PEFY-P VML-E
PEFY-P VML-E
Increased design flexibility for hotel and residential use.
Low static pressure (5Pa) meets
an application requiring direct air flow
Changeable air flow rate
(3 stage low-middle-high)
Low height unit with 225mm* high
Can be installed easily in tight spaces, such as ceiling cavities or drop-ceilings.
Notes: Drain lift-up pump not applicable.
Service space:500(19- 11 /16) or more Hole pitch 100(3- 15 /16) or more
*: 8- 7 /8in.
Flexible installation by rear
or bottom return air inlet.
245(9- 11 /16)+Drain
covering
configuration
height
225
(8- 7 /8)
20( 13 /16) or more
30(1- 3 /16)
Filter is attached as standard.
Access door
20/25/32 Model
unit: mm(in.)
Reduced noise thanks to the use of
newly designed centrifugal fan
Noise level table (Standard static pressure 220V)
Noise
Level
Capacity
High
Fan
Speed
Mid
Low
P20
36
29
25
P25
36
29
25
dB(A)
P32
40
29
25
Note: In the case of bottom inlet, the operating noise is
louder than in the case of rear inlet.
Drainage lines may be connected
on either the right or left side.
Perfect for use in hotels and other places
where line placement is a problem.
33

INDOOR UNIT
Ceiling concealed
type
PEFY-P VMM-E
PEFY-P VMM-E
Achieving creative air conditioning design
through a rich array of system materials.
Flexible installation for a variety of layouts
Long room
L-shaped rooms
Room with fixed
ceiling fixtures
Air outlet side compatible
with a variety of ducts (optional)
Multiple installation patterns for assorted applications and locations
Bottom intake (directly attached to panel)
Bottom intake (using canvas duct)
Adjustable setting of external static pressure to meet
system configuration and installation conditions
Maintenance panel
with air intake
Static pressure settings can be increased to
adjust to all kinds of ducts as well as
functional upgrade option (high performance
filter etc). An increase from the standard 50Pa
to 130* Pa is possible to cope with various
layout configurations.
*For P100~P125.
All-duct system
Square duct flange
Ceiling chamber system (2)
Maintenance panel
A bottom intake can
also be used
Ceiling chamber system (1)
Hanging ceiling installation
Maintenance panel
A rear intake can
also be used
Square duct flange
Slim 295mm main unit with optional drain up
mechanism ensures up to 600 mm of lift
System ceiling
Max.
600
Max.
416
184
295
34

INDOOR UNIT
Ceiling concealed
type
PEFY-P VMH-E
PEFY-P VMH-E
Increased design flexibility from sufficient external static pressure
allow authentic duct air- conditioning with an elegant interior layout.
External
static
pressure
(Pa)
Maximum external static pressure 200Pa
The additional external static pressure capacity provides flexibility for
duct extension, branching and air outlet configuration.
220V
230/240V
380V
400/415V
P40 P50 P63 P71 P80 P100 P125 P140 P200 P250
50/100/200
100/150/200
110/220
130/260
Reduced noise thanks to the use of
newly designed centrifugal fan
One-side maintenance
All maintenance to the unit, including
fan inspection and fan motor removal,
can be conducted from the inspection
opening on one side.
Drain up mechanism (option) ensures
up to 550mm* of lift
*: 21- 11 /16in.
The introduction of an upper drain mechanism allows the drain
connection to be raised as high as 550mm*, allowing more freedom in
piping layout design and reducing horizontal piping requirements.
Noise level table (Standard static pressure 220V)
dB(A)
Noise
Level
Capacity
Fan
Speed
High
Low
P40
34
27
P50
34
27
P63
38
32
P71
39
32
P80
41
35
P100
42
34
P125
42
34
P140
42
34
MAX.
550mm
(21- 11 /16in.)
222mm
(8- 3 /4in.)
328mm
(12- 15 /16in.)
35

INDOOR UNIT
Ceiling suspended
type
PCFY-P VGM-E
PCFY-P VGM-E
Designed for ultra-quiet operation and easy maintenance,
provides exceptionally comfortable air-conditioning.
Extra slim, extra stylish
Seek and slim with stylishly curved lines, the PCFY series blends right
into any interior. It also features a single air outlet which allows the
auto vane to act as a shutter when the unit is turned off.
Keeps airflow at optimum level
according to ceiling height
The most suitable airflow can be selected for ceilings up to 3.5m high,
enhancing air-conditioning efficiency and comfort.
Standard
High ceiling
Ceiling height 2.7m(8- 7 /8Ft) 3.5m(11- 1 /2Ft)
Greatly simplified installation
Auto vane distributes air evenly
The new direct suspension system eliminates the task of removing the
attachment fixture from the main unit, greatly shortening installation
time.
The auto vane swings up and down automatically to distribute air more
evenly to every corner of the room.
Direct suspension with attachment fixture attached
1. Leave attachment fixture
attached to main unit.
2. Suspend the attachment
fixture from the suspension bolts.
3. Simply tighten the nuts
to secure the unit.
Ceiling surface
Suspension
bolts
Attachment
fixture
Auto vane
Air outlet
Swing
*A one-touch suspension is also available: simply suspend
the main unit from the attachment fitting after securing
the latter to the ceiling.
Drain piping can be connected in one of two
directions, to the left or the right of the unit
36

INDOOR UNIT
Wall mounted
type
PKFY-P VAM-E
PKFY-P VGM-E
PKFY-P VFM-E
PKFY-P VAM
PKFY-P VFM
PKFY-P VGM
PKFY-P VAM-E
PKFY-P VGM-E
PKFY-P VFM-E
Elegant Design and Compact Dimensions Ideal for Offices,
Stores and Residential Uses.
Capacity range
Capacity P20 P25 P32 P40 P50
VAM
VGM
VFM
P63 P100
Compact design with 990mm* width
(PKFY-P VGM)
Width reduced by 20% to a compact
990mm*. *: 39in.
Extra compactness has been achieved thanks
to a 20%(260mm(10- 1 /4in.))
reduction in which compared with previous
models.
Compact 295mm(11- 5 /8in.) high body fits
snugly in even limited spaces (PKFY-P VAM)
In room air conditioning style, the grille
opens out allowing the filter to be removed.
The filter and open grille can therefore be
thoroughly and easily cleaned.
Quiet operation (PKFY-P VGM)
Among the quietest in the industry
Airflow passage configuration that assures quiet operations
1. The unit incorporates a randon pitch cycling fan. By changing fan
intervals reduction in airflow. Optimal design of the airflow passage
gives a shorted fan diameter and allows a highly compact installation.
2. Thanks to a highly practical casing configuration, airflow
generated by the fan is distributed uniformly.
3. Due to careful positioning of the vertical vane axis, air is blown
evenly from the fan. This prevents mixing with secondary air,
and also suppresses condensation.
Front grille opens out - easy filter cleaning (PKFY-P VGM)
3
Front grille
opens out
1
2
Lightweight 8.5kg(20lbs) unit easy to
transport and install (PKFY-P VAM)
Front power supply box for easier
wiring even after installation
5-way piping provides more flexibility
in selecting installation sites
37
Auto-flap shutter enhances
good looks
The front power supply box allows electrical
wiring work to be done after the indoor unit
has been installed. For easier installation, all
the screws required for securing the indoor
unit to the wall are accessible from the front
of the unit.
All piping including drainage can be
connected from the rear, right, base, and left
of the unit, providing much greater flexibility
out piping and selecting installation site.

INDOOR UNIT
Floor standing
type
PFFY-P VKM-E
New
PFFY-P VKM-E
For living rooms, bed rooms, or offices where a sophisticated
design is required. The latest Mitsubishi innovation – floor-standing
air-conditioner sophisticated in design, rich in function.
Quiet Operation
Mitsubishi Electric air conditioners have
always been some of the quietest model
available in the market. Our new floorstanding
models are no exception.
It can create a silent and comfortable space
where the occupants would not even
recognize the existence
of air conditioner
operation.
✻2.5kw class
ONLY
27dB
Noise level
Subway car
interior
Quiet passenger
car interior
(40km/h)
Library interior
Human
Sound of hearing limits
rustling leaves (Extremely quiet)
80dB
60dB
40dB
%@*
JDA
GKEAJAIJ
10dB
Sophisticated Design
From Mitsubishi
Electric, an
innovative new floorstanding
airconditioner.
Our
pleasing mix of
streamlined form and
diversified function.
Engineered to keep
room walls free,
furnish comfy cooling
in summer, toasty heating in winter.
Deluxe look in
“Glossy Pure White” color
Sleek louvers look just like
flat panels
Smart upper/lower air outlets
close when switched off
The “Glossy Pure White” colour ensures a deluxe look, the perfect
match for any room. Both upper and lower air outlets remain closed
when switched OFF, in a smart and striking image.
A superb new air-conditioner from Mitsubishi, providing a handsome
fit for your own distinctive interior.
Optimum Air Distribution
Comfy room temperatures are realized by the optimum, powerful and
efficient air distribution through upper and lower air outlets.
The upper vane angle is remote controllable, with 5 air flow direction
levels (+Swing and Auto modes) and 4 wind power levels (+Auto
mode).
By setting the vane angle almost vertical, annoying direct wind can be
avoided for your better comfort.
The unit body is slim and
trim, the essence in
compact. An ideal size for
living rooms, bedrooms,
attics and more.
The removable and
washable front panel makes
cleaning a snap.
Slim but Mighty
700mm
Easy and regular cleaning allows your air-conditioner stay beautiful
while keeping its energy-efficient operation always possible.
600mm
200
mm
The air from both upper and lower air
outlets is optimally controlled and distributed
evenly to every corner of the room.
In heating mode, the warm air is smartly
controlled to stay at the floor level: Your
feet do not feel chilled any more!
14 16 18 20 22 24 26 ˚C
38

INDOOR UNIT
Floor standing
type
PFFY-P VLEM-E
PFFY-P VLEM-E
Floor mounted lowboy type
effective in perimeter zone.
Standardized design with mild lines.
Supports various types of spaces from
office buildings and shop buildings to
hospitals.
Water vapor permeable film humidifier
can be installed.
Remote control can be installed onto
the main unit.
Compact unit for easy air
conditioning in perimeter zone.
The compact body of 220mm(7- 7 /8in.) in
depth can be easily installed in the perimeter
zone for effective air conditioning in the
perimeter zone.
Electronics dry function
dehumidify refreshingly.
Optimum dehumidification depending on
indoor temperature to prevent over-cooling.
Refreshing dehumidification can be attained.
INDOOR UNIT
Floor mounted
concealed type
PFFY-P VLRM-E
PFFY-P VLRM-E
Neatly installed with pericover concealed.
Easy installation in perimeter zone.
Compact unit for easy air conditioning in perimeter zone.
The body is concealed in the pericover to pursue harmony with the interior.
The compact body of 220mm(7- 7 /8in.) in depth can be easily installed in the perimeter zone.
Electronics dry function dehumidify refreshingly to prevent over-cooling.
Optimum dehumidification depending on indoor temperature to prevent over-cooling. Refreshing
dehumidification can be attained.
39

INDOOR UNIT
Fresh Air
Intake Type
PEFY-P VMH-E-F
PEFY-P VMH-E-F
Fresh Air can be taken in with temperature control.
Ideal for Offices, Stores and Restaurant.
The Fresh Air intake indoor unit
can be installed in any place.
* Limits of capacity connectable to outdoor unit
Max. 110% of outdoor unit capacity, excepting heating at outdoor temperature of less than -5˚C(23˚F) (100%).
The Fresh Air intake indoor unit can take
fresh outdoor air into any building in any
place at any time.
Office, Lobby, Workshop,
Rest room, nursery home,
Smoking corner,
Kitchen in restaurant
Example
1. Nurcery home
Fresh Air intake
indoor unit
Private room
Ventilating fan
Passage
Air flow
Private room
Ventilating fan
2. Workshop
Exhaust
air
Fresh air
Polluted air
Workshop
Office
Fresh Air intake
indoor unit
Installing fresh Air intake indoor unit (Image)
Fresh Air intake indoor unit
Exhaust
air
EA
Supply air
Fresh
air
OA
< Note>
Fan remains of in operation during Thermo-OFF. Using this model with other
type of indoor unit is recommended for Cold Draft prevention because Cold Draft
might occur by using only this model that takes in fresh air.
40

0
INDOOR UNIT
Specifications & External Dimensions
PLFY-P VCM-E
For 50Hz
Area only
Power source
❇ 1
Cooling capacity
❇ 1
❇ 1
Heating capacity
❇ 1
Power
Cooling
consumption Heating
Cooling
Current
Heating
External finish(Munsel No.)
Height
Dimension ❇ 2 Width
Depth
Net weight ❇ 2
Heat exchanger
Type
Fan
Motor
Airflow rate ❇ 2
(Low-Mid-High)
External static
pressure
Type
Output
Air filter
Refrigerant
pipe diameter
Gas(Flare)
Liquid(Flare)
Drain pipe diameter
Noise level (Lo-Mid-Hi) ❇2 ❇3
kW
Btu/h
kW
Btu/h
kW
kW
A
A
mm(in.)
mm(in.)
mm(in.)
kg(lbs.)
m 3 /min
L/s
cfm
Pa
kW
mm(in)
mm(in)
dB(A)
Specifications
PLFY-P20VCM-E PLFY-P25VCM-E PLFY-P32VCM-E PLFY-P40VCM-E
~ (Single phase), 220-230-240V 50Hz
2.2
2.8
3.6
4.5
7,500 9,600 12,300 15,400
2.5
3,2
4.0
5.0
8,500 10,900 13,600 17,100
0.05
0.05
0.23
0.23
0.05
0.05
0.23
0.23
0.06
0.06
0.28
0.28
0.06
0.06
0.28
0.28
Unit: Galvanized sheets with gray heat insulation, Panel: Munsell 0.70Y 8.59/0.97
Unit: 208(8-1/ 4 "), Panel: 20(13/ 16 ")
Unit: 570(22-1/ 2 "), Panel: 650(25-5/ 8 ")
Unit: 570(22-1/ 2 "), Panel: 650(25-5/ 8 ")
Unit: 15.5(35) Unit: 15.5(35) Unit: 17(38) Unit: 17(38)
Cross fin (Aluminum plate fin and copper tube)
Turbo fan × 1
8-9-10 8-9-10 8-9-11 8-9-11
133-150-167 133-150-167 133-150-183 133-150-183
283-318-353 283-318-353 283-318-388 283-318-388
External Dimensions
0 (direct blow)
Single phase induction motor
0.011 0.015 0.020 0.020
PP Honey comb
ø 12.7(1/ 2 ")
ø 6.35(1/ 4 ")
O.D. ø32(1-1/ 4 ") O.D. ø32(1-1/ 4 ") O.D. ø32(1-1/ 4 ") O.D. ø32(1-1/ 4 ")
28-31-35 28-31-37 29-33-38 30-34-39
Note: ❇1 Cooling/Heating capacity indicates the maximum value at operation under the following condition.
Cooling : Indoor 27˚C(80.6˚F)DB/19˚C(66.2˚F)WB,Outdoor 35˚C(95˚F)DB
Heating : Indoor 20˚C(68˚F)DB,Outdoor 7˚C(44.6˚F)DB/6˚C(42.8˚F)WB
❇2 External dimension/ net weight are shown in , and airflow rate/noise level are in (low-middle2-middle1-high).
❇3 It is measured in anechoic room.
PLFY-P20,25,32,40VCM-E
Unit : mm
15~37
Fresh air intake
Ceiling hole
576~620
420
Suspension bolt pitch
530
Suspension bolt pitch
570
335
570
Detail drawing of fresh air intake hole
ø100 25
ø73.4
3-ø2.8hole
Cut out hole
Burring hole
15~37
199
Drain pipe
352
VP-25 connection
335
(O.D.ø32)
15~37 576~620 Ceiling hole
15~37
Wiring entry
2
17 202
230
Suspension bolt M10 or W3/8
1
Ceiling surface
55 35
Terminal block Grille
650
301
Air outlet hole
V/M
Brand label
Grille
Drain hole
V/M
Auto vane
301
Air outlet hole
Air intake hole
118
120˚
120˚
Suspension bolt lower edge
650
377
48
121
93
66
193
208
235
182
87
57
56
38~58
31
Ceiling surface
27 +5
20
Models
1
2
41
V/M
35 55
377
Air intake hole
V/M
Air intake grille
Vane motor
PLFY-P20VCM-E
PLFY-P25VCM-E
PLFY-P32VCM-E
PLFY-P40VCM-E
Refrigerant pipe
(6.35mm dia.)
flared connection
1/4F
Refrigerant pipe
(12.7mm dia.)
flared connection
1/2F

INDOOR UNIT
Specifications & External Dimensions
PLFY-P VAM-E
Power source
Cooling capacity
Heating capacity
Power
consumption
Current
❇1
❇1
❇2
❇2
❇1
❇1
❇1
Cooling
Heating
Cooling
Heating
External finish(Munsel No.)
Dimension H x W x D ❇ 3
Net weight ❇ 3
Heat exchanger
Type
Fan
Airflow rate ❇ 3
(Low-Mid2-Mid1-High)
External static
pressure
Type
Motor
Output
Air filter
Refrigerant
pipe diameter
Gas
(Flare)
Liquid
(Flare)
Drain pipe diameter
Noise level (Lo-Mid2-Mid1-Hi) ❇3 ❇4
kW
BTU/h
kW
kcal/h
kW
kcal/h
BTU/h
kW
kW
A
A
mm
in.
kg(lbs.)
m 3 /min
L/s
cfm
Pa
kW
mm(in.)
mm(in.)
dB(A)
PLFY-P32,40,50,63,80,100,125VAM-E
Specifications
PLFY-P32VAM-E PLFY-P40VAM-E PLFY-P50VAM-E PLFY-P63VAM-E
~ 220-240V 50Hz / ~ 220V 60Hz
3.6 4.5 5.6 7.1
12,300
15,400 19,100 24,200
3.7
4.7 5.8
7.3
3,150 4,000 5,000 6,300
4.0 5.0 6.3 8.0
3,400
4,300 5,400 6,900
13,600
17,100 21,500 27,300
0.12
0.12
0.59
0.59
Note: ❇1 Cooling/Heating capacity indicates the maximum value at operation under the following condition.
Cooling : Indoor 27 ˚C(80.6˚F) DB/19˚C(66.2˚F)WB,Outdoor 35˚C(95˚F)DB
Heating : Indoor 20˚C(68˚F)DB,Outdoor 7˚C(44.6˚F)DB/6˚C(42.8˚F)WB
❇2 Cooling capacity indicates the maximum value at operation under the following condition.
Cooling : Indoor 27˚C(80.6˚F)DB/19.5˚C(67.1˚F)WB,Outdoor 35˚C(95˚F)DB (WR2: water 30˚C(80˚F))
Heating : Indoor 21˚C(69.8˚F)DB,Outdoor 7˚C(44.6˚F)DB/6˚C(42.8˚F)WB (WR2: water 20˚C(68˚F))
❇ 3 External dimension/ net weight are shown in , and airflow rate/noise level are in (low-middle2-middle1-high).
❇ 4 It is measured in anechoic room.
0.14
0.14
0.68
0.68
0.16
0.16
0.78
0.78
Panel : 0.70Y 8.59/0.97
258x 840 x 840
298(30) x 840(950) x 840(950)
10-3/16"

INDOOR UNIT
Specifications & External Dimensions
PLFY-P VLMD-E
Power source
❇ 1
❇ 1
Cooling capacity
❇ 2
❇ 2
❇ 1
Heating capacity
❇ 1
❇ 1
Power
Cooling
consumption Heating
Cooling
Current
Heating
External finish(Munsel No.)
Dimension H x W x D ❇ 3
Net weight
❇ 3
Heat exchanger
Type
Fan
Motor
Air filter
Airflow rate (Lo-Mid-Hi)
External static pressure
Type
Output
kW
BTU/h
kW
kcal/h
kW
kcal/h
BTU/h
kW
kW
A
A
mm
in.
kg(lbs.)
m 3 /min
L/s
cfm
Pa
kW
Specifications
PLFY-P20VLMD-E PLFY-P25VLMD-E PLFY-P32VLMD-E PLFY-P40VLMD-E
~ 220-240V 50Hz / ~ 220-230V 60Hz
2.2
2.8
3.6
4.5
7,500 9,600 12,300
15,400
2.3 2.9 3.7
4.7
2,000
2,500
3,150
4,000
2.5
3.2
4.0
5.0
2,200 2,800 3,400
4,300
8,500 10,900 13,600
17,100
0.072 / 0.075
0.065 / 0.069
0.36 / 0.37
0.30 / 0.32
0.072 / 0.075
0.065 / 0.069
0.36 / 0.37
0.30 / 0.32
0.072 / 0.075
0.065 / 0.069
0.36 / 0.37
0.30 / 0.32
0.081 / 0.085
0.074 / 0.079
0.40 / 0.42
0.34 / 0.37
Unit: Galvanizing Decoration Panel: ABS (0.7Y 8.59/0.97) Service Panel: Galvanizing (0.7Y 8.59/0.97)
290 x 776 x 634
11- 7 /16"< 13 /16"> x30- 9 /16"

INDOOR UNIT
Specifications & External Dimensions
PLFY-P VLMD-E
External Dimensions
PLFY-P20, 25, 32, 40, 50, 63, 80, 100VLMD-E
Unit : mm
Note: 1.Use M10 screw for the lifing bolt (field supply).
2.It is available to connect the branch duct on right and left side both.
3.On Model :50, 100, you would use flare nut packed with the Indoor
Unit, when connnecting the Outdoor Unit for R407C, R22.
4.In order to increase the strength of the flare nut, the size of some
of them has been increased.
H
240 197
190 222 4-ø2.9 Mounting hole
45 216
73 202
48
70 146
Model Gas pipe:LP ø12.7
20·25·32·40 Liquid pipe:HP ø6.35
574
507
634
670
Model Gas pipe:LP ø12.7
50 ø15.88
Liquid pipe:HP ø6.35
ø9.52
Model Gas pipe:LP ø15.88
63·80 Liquid pipe:HP ø9.52
Model Gas pipe:LP ø15.88
100 ø19.05
Liquid pipe:HP ø9.52
Drain hose VP-25 (accessory)
48
108
Branch duct Fx110 knock out hole
(both side)(Note:2)
D(Lifting Bolt Pitch)
B
D(Lifting bolt pitch)
C
F
108
G-ø2.9 Mounting hole
221
Control box
E
3
Terminal bed(Power source)
Terminal bed(Transmission)
Terminal box
68
574 (Lifting Bolt Pitch)
634
497
70
146
68
2
1
45
110
159
266
122
190
290
More Than 350
60
52
34
20 B
20
20
670
20
20
Fresh air intake 240x45 knock out hole
Drain hole
Water filling port
Air filter
Standard center panel
A
300mm or less
Model
PLFY-P20VLMD-E
PLFY-P25VLMD-E
PLFY-P32VLMD-E
PLFY-P40VLMD-E
PLFY-P50VLMD-E
PLFY-P63VLMD-E
PLFY-P80VLMD-E
PLFY-P100VLMD-E
CMP-40VLW-B 1080 1040 776 824 388
CMP-63VLW-B
A
B
C
1250 1210 946
D
994
E
473
F
217.5✕2
=435
188.5✕4
CMP-100VLW-B 1750 1710 1446 1494 723
=754
10
G H(Liquid) H(Gas)
6
17
22
22
27
29
36
710
583mmMAX
3
170mm ± 5mm(Actual Length)
PLFY-P125VLMD-E
48
574
48
Fresh air intake ø150 knock out hole
303
107 1756
1970
127
1756(Lifting bolt pitch)
1708
45˚
856
107
Branch duct ø200 knock out hole (both side)
127
606
670
1
2
3
Terminal bed
(Transmission)
Terminal bed
(Power source)
Note: 1.Use M10 screw for the lifting bolt (field supply).
2.On this model, you would use flare nut packed
with the Indoor Unit, when connnecting the
Outdoor Unit for R407C, R22.
3.In order to increase the strength of theflare nut,
the size of some of them has been increased.
Model
PLFY-P125VLMD-E
38
A(Liquid) A(Gas)
22 36
Gas pipe:LP ø15.88
ø19.05
Liquid pipe:HP ø9.52
Drain hose VP-25 (accessory)
Water filling port
68 574(Lifting bolt pitch) 68
606
476
70 178
106
3 1
2
A
ø172
90˚
90˚
4-ø2.9Mounting hole
181
20
145
90˚
ø224
1970(Ceiling opening)
Control box
4-ø2.8Mounting hole
20
235
Terminal box
Air filter
222
70 333
20 670(Ceiling opening) 20
155
192
255
290
Drain hole
45
20 338~353
More than 350
2010
300mm or less
170mm±5mm(Actual length)
710
600mm Max
3
Standard center panel
(CMP-125VLW-B)
44

INDOOR UNIT
Specifications & External Dimensions
PMFY-P VBM-E
Specifications
PMFY-P20VBM-E PMFY-P25VBM-E PMFY-P32VBM-E PMFY-P40VBM-E
Power source
~220-240V 50Hz / ~ 220V 60Hz
❇1 kW
2.2 2.8 3.6
4.5
Cooling capacity
❇1 BTU/h
7,500 9,600 12,300
15,400
❇2 kW
2.3 2.9 3.7
4.7
❇2 kcal/h
2,000 2,500 3,150 4,000
❇1 kW
2.5 3.2 4.0
5.0
Heating capacity
❇1 kcal/h
2,200 2,800 3,400
4,300
❇1 BTU/h
8,500 10,900 13,600
17,100
Power consumption
Cooling kW
0.042
0.044
0.054
Heating kW
0.042
0.044
0.054
Current
Cooling A
0.20
0.21
0.26
Heating A
0.20
0.21
0.26
External finish
Panel : 0.98Y8.99/0.63
Dimension H x W x D ❇ 3
mm(in.) 230 x 812 x 395 (9- 1 /16"

INDOOR UNIT
Specifications & External Dimensions
New
PEFY-P VMR-E-L/R
Power source
Cooling capacity
Heating capacity
Power consumption
Current
External finish
Drain pipe diameter
Noise level
(Low-Mid2-Mid1-High)
❇ 4
Note:
Cooling
Heating
Cooling
Heating
Dimension H x W x D
Net weight ❇ 3
Heat exchanger
Type
Airflow rate
(Low-Mid-High)
Fan
External static pressure
Type
Motor
Output
Air filter
Refrigerant
pipe diameter
❇ 3
Gas(Flare)
Liquid(Flare)
mm(in.)
kg(lbs.)
m 3 /min
Pa
kW
mm(in.)
mm(in.)
Specifications
PEFY-P20VMR-E-L/R PEFY-P25VMR-E-L/R PEFY-P32VMR-E-L/R
1-phase 220/230/240 V 50Hz 220/230V 60Hz
❇1 kW
2.2 2.8 3.6
❇1 BTU/h
7,500 9,600 12,300
❇2 kW
2.3 2.9 3.7
❇2 kcal/h
2,000 2,500 3,150
❇1 kW
2.5 3.2 4.0
❇1 kcal/h
2,200 2,800 3,400
❇1 BTU/h
8,500 10,900 13,600
kW
0.06/0.06
0.06/0.06
0.07/0.08
kW
0.06/0.06
0.06/0.06
0.07/0.08
A
0.29/0.29
0.29/0.29
0.34/0.38
A
0.29/0.29
0.34/0.38
220V
20-25-30 20-25-33
230V dB(A)
21-26-32 21-26-35
240V 22-27-30
22-27-33
❇1 Cooling/Heating capacity indicates the maximum value at operation under the following condition.
Cooling: Indoor 27˚C (81˚F) DB/19˚C (66˚F) WB, Outdoor 35˚C (95˚F) DB
Heating: Indoor 20˚C (68˚F) DB, Outdoor 7˚C (45˚F)DB/6˚C (43˚F) WB
❇2 Cooling capacity indicates the maximum value at operation under the following condition.
Cooling : Indoor 27˚C(80.6˚F)DB/19.5˚C(67.1˚F)WB,Outdoor 35˚C(95˚F)DB (WR2: water 30˚C(80˚F))
External Dimensions
0.29/0.29
Galvanized
292 x 640 x 580
18 (40)
Cross fin (Aluminum fin and copper tube)
Sirocco fan ✕ 1
4.8-5.8-7.9 4.8-5.8-9.3
5
1-phase induction motor
0.018
PP Honeycomb fabric (washable)
ø 6.35( 1/4")
ø 12.7(1/2")
O.D. 26(1-1/32)
Heating : Indoor 21˚C(69.8˚F)DB,Outdoor 7˚C(44.6˚F)DB/6˚C(42.8˚F)WB (WR2: water 20˚C(68˚F))
❇3 The external static pressure is set to 100Pa (at 220V) / 150Pa (at 230, 240V) at factory shipment.
❇4 Measured in anechoic room. Noise levels of the unit with a rear air inlet. (Noise levels are higher for the unit with a
bottom air inlet.)
0.023
PEFY-P20,25,32VMR-E-L/R
Right side
Unit : mm
Air filter
630
300 (In case of bottom inlet) 23
584 (Suspension bolt pitch)
292 (In case of rear inlet)
80 530
50 or below
Rear
air inlet
Suspension bolt hole
Suspension bolt outlet
(Note 1)
Rear
air inlet
Terminal bed (Power source)
Terminal bed (M-Net Transmission)
Control box
439 (Suspension bolt pitch) 105
580 (In case of rear inlet)
570 (In case of bottom inlet)
2
1
3
Bottom plate 113
148
Bottom air inlet
2x10-ø3
Air outlet
2x2-ø3
50x9=450
480
622
50
15
62 25
100
Left side
30
15
50 25
100 28
275
250
Note 1. Use M10 screw for the suspension bolt (field supply).
50mm or below of clearance between the Indoor unit top and the end of the
suspension bolt will make maintenance of the Indoor heat exchanger easier.
2. Access door of 450mm x 450mm at the ceiling under the drain pan should be
designed for heat exchanger cleaning and maintenance.
3. This drawing shows the left piping specification. The symmetry shows the
right piping specification.
Model name: PEFY-P20 · 25 · 32VMR-E-L
PEFY-P20 · 25 · 32VMR-E-R
4. Period cleaning of drain pan will prevent water overflowing.
Gradient piping design is needed for water draining.
5. The inlet direction can be changed between rear inlet and bottom inlet.
Keep the inlet space between the ceiling and the unit in case of bottom
inlet.
Required space for service and maintenance
(Note 2)
300
25
450 50~150
450
500
50~150
Make the access door at the appointed position properly
for service maintenance.
Access door
Ceiling surface
More than 20mm
More than 20mm
Drain pan
Hose band
Insulation material
Adhesion
Rigid vinyl drain pipe
Insulation material
or drain pan
Urethane foam
150
Do not leave space.
Drain hose (accessory)
Refrigerant pipe (gas) brazed
Refrigerant pipe (liquid) brazed
Drain pipe connection diameter
ø12.7·································➀
ø6.35·································➁
VP20(dia. 26mm) ·············➂
46

INDOOR UNIT
Specifications & External Dimensions
New
PEFY-P VMS-E
Power source
Cooling capacity
❇1
Heating capacity
❇1
Power input
Current
Temperature set range Remote controller
Fan ❇2 Type x Quantity
External static press
Motor type
Motor output
Airflow rate(Low-Mid-High)
External finish
External dimension
H x W x D
Net weight
Refrigerant piping Liquid R410A
diameter
R407C,R22
Gas
Drain piping diameter
Noise level (Low-Mid-High)
(mesured in anechoic room)
Air filter
Connectable outdoor unit
Heat exchanger
R410A
R407C,R22
kW
kW
kW
A
˚C(˚F)
Pa
kW
m 3 /min
mm
In.
kg
mm(in.)
mm(in.)
mm(in.)
mm(in.)
mm(in.)
dB
Specifications
PEFY-P20VMS-E PEFY-P25VMS-E PEFY-P32VMS-E PEFY-P40VMS-E PEFY-P50VMS-E PEFY-P63VMS-E
1-phase 220-240V 50Hz 1-phase 220-230V 60Hz
2.2
2.8
3.6
4.5
5.6
7.1
2.5
3.2
4.0
5.0
6.3
8.0
0.08 0.06
0.39 0.28
19 to 30 (67 to 86) 17 to 28 (63 to 83)
0.08
0.39
19 to 30 (67 to 86)
0.06
0.28
17 to 28 (63 to 83)
0.09
0.44
19 to 30 (67 to 86)
0.07
0.33
17 to 28 (63 to 83)
0.11
0.53
19 to 30 (67 to 86)
Note: ❇ 1.Cooling/Heating capacity indicates the maximum value at operation under the following condition.
Indoor : 27˚CD.B./19˚CW.B. (81˚FD.B. / 66˚FW.B.) Outdoor : 35˚CD.B. (95˚FD.B. )
Indoor : 20˚CD.B. (68˚FD.B.) Outdoor : 7˚CD.B. / 6˚CW.B. (45˚FD.B. / 43˚FW.B.)
Pipe length : 7.5m (24-9/16ft) Height difference : 0m (0ft)
❇ 2.The external static pressure is set to 15 Pa at factory shipment.
6-7-8
22-25-27
0.09
0.42
17 to 28 (63 to 83)
Sirocco fan x 3
5-15-35-50
DC brushless motor
0.096
7.5-8.5-10
8-9.5-11
Galvanized
200 x 900 x 700
7-7/8 x 35-7/16 x 27-9/16
23 24
ø6.35(ø1/4) Brazed
ø6.35(ø1/4) Brazed
ø12.7(ø1/2) Brazed
ø12.7(ø1/2) Brazed
25-28-30
O.D. 32(1-9/32)
28-30-33
PP Honeycomb fabric (washable)
R410A, R407C, R22 CITY MULTI
Cross fin(Aluminium fin and copper tube)
0.13
0.63
19 to 30 (67 to 86)
0.11
0.52
17 to 28 (63 to 83)
9.5-11-13
ø6.35(ø1/4) Brazed
ø9.52(ø3/8) Brazed
ø12.7(ø1/2) Brazed
ø15.88(ø5/8) Brazed
30-32-35
0.14
0.68
19 to 30 (67 to 86)
0.12
0.57
17 to 28 (63 to 83)
Sirocco fan x 4
12-14-16.5
200 x 1100 x 700
7-7/8 x 43-5/16 x 27-9/16
28
ø9.52(ø3/8) Brazed
ø9.52(ø3/8) Brazed
ø15.88(ø5/8) Brazed
ø15.88(ø5/8) Brazed
30-33-36
External Dimensions
PEFY-P20,25,32,40,50,63VMS-E
Unit : mm
15
20
12
157.5
37 100
37
20 157.5
12 37 100
37
25
57
2 X E-ø2.9
2 Refrigerant piping
brazing connection (liquid)
D (Duct)
30 100 X (E-1)=F
100
20
Air
outlet
100
150(Duct) 23
100 25
10
49
23
10
270
625(Suspension bolt pitch)
700
677
Drain pipe
(O.D.ø32)
Drainpump
Air
inlet
20-ø2.9
Air filter
Suspension bolt hole
4-14 X 30 Slot
Knockout hole ø27
(Power source wiring)
Control box
48
A
90
102
170
B (Suspension bolt pitch)
C
23
200
20
860
12 88
100 X 7=700
88
100
Knockout hole ø27
(Transmission wiring)
1060
88
100 X 9=900
88
100
20
12
24-ø2.9
Model:P63(Note3)
Air filter
Air filter
50
More than 20mm
More than 20mm
50
G 450
Note2
50~150
175mm +- 5 mm
(Actual length)
Less than 300mm
777
450
More than 300
Access door
Required space for service and maintenance
Ceiling surface
Access door
Make the access door at the appointed position properly
for service maintenance.
Drain hose (I.D.ø32)
Less than 550mm
2 X 2-ø2.9
116 70
1 Refrigerant piping
270
Drain pipe(O.D.ø32)
brazing connection (gas)
(Spontaneous draining)
Model
A B C D
PEFY-P20,25,32,40VMS-E
PEFY-P50VMS-E
PEFY-P63VMS-E
900
1100
952
1152
998
1198
860
1060
E
9
11
Terminal bed(Power source)
Terminal bed(Transmission)
F
800
G
1000
1000 1200
1Gas pipe 2 Liquid pipe
ø12.7 ø6.35
✻1
✻2
ø12.7
ø15.88
ø15.88
✻1
✻2
ø6.35
ø9.52
ø9.52
Note 1. Use M10 screw for the Suspension bolt (field supply).
2. Keep the service space for the maintenance at
the bottom.
3. This chart indicates for PEFY-P20~50VMS-E models,
which has 3 fans. PEFY-P63VMS-E model have 4 fans.
4. In case of the inlet duct is used,remove the air filter(supply with
the unit), then install the filter(field supply) at suction side.
✻1 : R410A outdoor unit
✻2 : R407C,R22 outdoor unit
47

INDOOR UNIT
Specifications & External Dimensions
PEFY-P VML-E
Power source
Cooling capacity
Heating capacity
Power consumption
(50/60Hz)
Current
External finish
Dimension H x W x D
Net weight
Heat exchanger
Fan
Motor
Air filter
Type
Airflow rate
(Lo-Mid-Hi)
External static pressure
Type
Output
Refrigerant
pipe diameter
Drain pipe diameter
Noise level (Lo-Mid-Hi)
Note:
PEFY-P20,25,32VML-E
Cooling
Heating
Cooling
Heating
❇1
❇1
❇2
❇2
❇1
❇1
❇1
Gas(Brazing)
Liquid(Brazing)
kW
BTU/h
kW
kcal/h
kW
kcal/h
BTU/h
kW
kW
A
A
mm(in.)
kg(lbs.)
m 3 /min
L/s
cfm
Pa
kW
mm(in.)
mm(in.)
Specifications
❇5 dB(A)
❇ 1 Cooling/Heating capacity indicates the maximum value at operation under the following condition.
Cooling : Indoor 27˚C(80.6˚F)DB/19˚C(66.2˚F)WB,Outdoor 35˚C(95˚F)DB
Heating : Indoor 20˚C(68˚F)DB,Outdoor 7˚(44.6˚F)CDB/6˚C(42.8˚F)WB
❇ 2 Cooling capacity indicates the maximum value at operation under the following condition.
Cooling : Indoor 27˚C(80.6˚F)DB/19.5˚C(67.1˚F)WB,Outdoor 35˚C(42.8˚F)DB (WR2: water 30˚C(80˚F))
Heating : Indoor 21˚C(69.8˚F)DB,Outdoor 7˚C(44.6˚F)DB/6˚C(42.8˚F)WB (WR2: water 20˚C(68˚F))
❇ 3 The external static pressure is set to 100Pa (at 220V) /150Pa (at 230, 240V) at factory shipment.
❇ 4 The value are that at 240V.
❇ 5 It is measured in anechoic room.
The part air intake duct is attached. (✻3)
(When the air intake duct is used)
PEFY-P20VML-E PEFY-P25VML-E PEFY-P32VML-E
~ 220-240V 50Hz / 60Hz
2.2 2.8 3.6
7,500 9,600 12,300
2.3 2.9 3.7
2,000 2,500 3,150
2.5 3.2 4.0
2,200 2,800 3,400
8,500 10,900 13,600
0.05/0.06
0.07/0.09
0.05/0.06
0.07/0.09
0.24/0.28
0.32/0.42
0.24/0.28
0.32/0.42
Galvanizing
225 x 720 x 550 (8- 7 /8" x 28- 3 /8" x 21- 11 /16")
18 (40)
Cross fin (Aluminum plate fin and copper tube)
Sirocco fan ✕ 1
4.8-5.8-7.9 4.8-5.8-9.5
80-97-132 80-97-158
170-205-279 170-205-335
5
Single phase induction motor
0.023 0.032
PP Honeycomb fabric (washable)
ø 12.7( 1 /2")
ø 6.35( 1 /4")
R1 (External thread)
25-29-36 25-29-40
External Dimensions
Unit : mm
Air filter
710
23 664 (Lifting bolt pitch)
80
610
Air inlet
Lifting bolt
Control box
459 (Lifting bolt pitch)
550 (✻1)
510
2 1 148
80
30
15
55
2✕3-ø3
13.5
14
12-ø3
Air outlet
15
14
16 50
50✕11=550
720
582
42.5
65.5
204.5
Bottom plate
Note 1.Use M10 screw for the lifting bolt (field supply).
2.Keep the service space for the maintenance
from the bottom when the heat exchanger is
cleaned.
3.The direction of air intake can be changed from
the bottom to the rear by attaching the bottom
plate to the air intake side.
4.Drain Pan is changeable from right and left.
5.The dimension is changed, in case the optional
long-life filter is attached.
RearAir-Intake spec.:Depth is increased by
30mm(✻1)
BottomAir-Intake spec.:Height is increased
by 30mm(✻2)
Refrigerant piping brazing connection
(gas ø12.7 copper tube):LP ··· 1
Refrigerant piping brazing connection
(liquid ø6.35 copper tube):HP ··· 2
Drain piping connection R1 (External thread) ··· 3
540
In case of rear inlet
Air inlet
50
50
127
225 (✻2)
In case of bottom inlet
Air filter
Terminal bed
(Power source)
Terminal bed
(Transmission)
3
Bottom plate
113
Air filter
Air inlet
48

INDOOR UNIT
Specifications & External Dimensions
PEFY-P VMM-E
Power source
Cooling capacity
Heating capacity
Power consumption
(50Hz)
Current
External finish
Dimension H x W x D
Net weight
Heat exchanger
Type
Fan
Airflow rate
(Lo-Mid-Hi)
❇ 1
❇ 1
❇ 2
❇ 2
❇ 1
❇ 1
❇ 1
Cooling
Heating
Cooling
Heating
External static pressure
Type
Motor
Output
Air filter
Gas
Refrigerant (Flare)
pipe diameter Liquid
(Flare)
Drain pipe diameter
Noise level (Lo-Mid-Hi) ❇ 3
kW
BTU/h
kW
kcal/h
kW
kcal/h
BTU/h
kW
kW
A
A
mm(in.)
kg(lbs.)
m 3 /min
L/s
cfm
Pa
kW
mm(in.)
mm(in.)
dB(A)
6.0-7.2-8.5
Specifications
PEFY-P20VMM-E PEFY-P25VMM-E PEFY-P32VMM-E PEFY-P40VMM-E
~220-240V 50Hz
2.2 2.8
3.6
4.5
7,500 9,600 12,300
15,400
2.3 2.9 3.7
4.7
2,000 2,500 3,150
4,000
2.5 3.2 4.0
5.0
2,200 2,800 3,400
4,300
8,500 10,900 13,600
17,100
0.15
0.17
0.19
0.15
0.17
0.19
0.73
0.81
0.92
0.73
0.81
0.92
295 x 815 x 700
(11- 5 /8 "x 32- 1 /8" x 27- 9 /16")
27(60)
Cross fin (Aluminum plate fin and copper tube)
Sirocco fan✕ 1 Sirocco fan✕ 2
100-120-142 125-150-175 167-200-233 200-242-283 225-270-317
212-254-300 265-318-371 353-424-494 424-512-600 477-572-671
30/50/100
Single phase induction motor
0.075
0.078
PP Honeycomb fabric (washable)
27-30-32
ø 12.7( 1 /2")
ø 6.35( 1 /4")
7.5-9.0-10.5
10.0-12.0-14.0
R1 (External thread)
28-32-35 31-34-37
PEFY-P50VMM-E
PEFY-P63VMM-E
5.6
7.1
19,100 24,200
5.8 7.3
5,000 6,300
6.3
8.0
5,400 6,900
21,500 27,300
0.20
0.22
0.20
0.22
0.98
1.07
0.98
1.07
Galvanizing
295 x 935 x 700
295 x 1,175 x 700
(11- 5 /8" x 36- 13 /16" x 27- 9 /16") (11- 5 /8" x 46- 5 /16" x 27- 9 /16")
33(73) 42(93)
12.0-14.5-17.0
ø 12.7( 1 /2")[R410A]
ø 15.88( 5 /8")[R22,R407C]
ø 6.35( 1 /4")[R410A]
ø 9.52( 3 /8")[R22,R407C]
31-35-38
13.5-16.2-19.0
ø 15.88( 5 /8")
ø 9.52( 3 /8")
49
Power source
Cooling capacity
Heating capacity
Power consumption
(50Hz)
Current
External finish
Dimension H x W x D
Net weight
Heat exchanger
Type
Fan
Airflow rate
(Lo-Hi)
❇ 1
❇ 1
❇ 2
❇ 2
❇ 1
❇ 1
❇ 1
Cooling
Heating
Cooling
Heating
External static pressure
Type
Motor
Output
Air filter
Gas
Refrigerant (Flare)
pipe diameter Liquid
(Flare)
kW
BTU/h
kW
kcal/h
kW
kcal/h
BTU/h
kW
kW
A
A
mm(in.)
PEFY-P71VMM-E PEFY-P80VMM-E PEFY-P100VMM-E
~220-240V 50Hz
PEFY-P125VMM-E PEFY-P140VMM-E
8.0
27,300
9.0
30,700
11.2
38,200
14.0
47,800
16.0
54,600
8.3
9.3
11.6 14.5 16.3
7,100
8,000
10,000
12,500
14,000
9.0
10.0
12.5
16.0
18.0
7,700
8,600
10,800 13,800 15,500
30,700
34,100
42,700 54,600 61,400
0.25
0.29
0.40
0.42
0.25
0.29
0.40
0.42
1.15
1.34
1.90
1.95
1.15
1.34
1.90
1.95
Galvanizing
295 x 1,175 x 700
325 x 1,415 x 740 325 x 1,715 x 740
(11-5/8" x 46-5/16" x 27-9/16") (12-13/16" x 55-3/4" x 29-3/16") (12-13/16" x 67-9/16" x 29-3/16")
kg(lbs.)
42(93)
62(137) 65(144) 70(155)
Cross fin (Aluminum plate fin and copper tube)
Sirocco fan✕2
m 3 /min
L/s
cfm
14.5-18.0-21.0
242-300-350
512-636-742
23.0-33.0
383-550
812-1165
28.0-40.0
467-667
989-1413
29.5-42.0
492-700
1042-1483
Pa 30/50/100
50/130
Single phase induction motor
kW
0.078
0.200
PP Honeycomb fabric (washable)
0.280
mm(in.)
mm(in.)
ø 15.88(5/8")
ø 15.88(5/8") [R410A]
ø 19.05(3/4") [R22,R407C]
ø 9.52 (3/8")
Drain pipe diameter
R1 (External thread)
Noise level (Lo-Mid-Hi) ❇ 3 dB(A) 32-36-39
40-44 42-45 42-45
Note: ❇ 1 Cooling/Heating capacity indicates the maximum value at operation under the following condition.
Cooling : Indoor 27˚C(80.6˚F)DB/19˚C(66.2˚F)WB,Outdoor 35˚C(95˚F)DB
Heating : Indoor 20˚C(68˚F)DB,Outdoor 7˚C(44.6˚F)DB/6˚C(42.8˚F)WB
❇ 2 Cooling capacity indicates the maximum value at operation under the following condition.
Cooling : Indoor 27˚C(80.6˚F)DB/19.5˚C(67.1˚F)WB,Outdoor 35˚C(95˚F)DB (WR2: water 30˚C(80˚F))
Heating : Indoor 21˚C(69.8˚F)DB,Outdoor 7˚C(44.6˚F)DB/6˚C(42.8˚F)WB
❇ 3 It is measured in anechoic room.
(WR2: water 20˚C(68˚F))

INDOOR UNIT
Specifications & External Dimensions
PEFY-P VMM-E
External Dimensions
PEFY-P20,25,32,40,50,63,71,80VMM-E
Unit : mm
Note: 1. On Model :50, you would use flare nut packed
with the Indoor Unit, when connnecting the
Outdoor Unit for R407C, R22.
2. In order to increase the strength
of the flare nut, the size of some
of them has been increased.
1 Refrigerant piping flare connection (liquid øF copper tube):HP
2 Refrigerant piping flare connection (gas øG copper tube) :LP
3 Drain R1(External thread)
4 Electrical parts box
5 Drain Pump (Option)
Set
6 Drain Pipe (Option)···Flexible joint VP-25(I.D.ø32)
7 Filter
Model A B C D E
P20,25,32 652 245 - 710 684
P40 772 305 - 830 804
P50 772 305 - 830 804
P63,71,80 1012 280 290 1070 1044
In case of rear inlet
3.5
21
✻1
✻2
H
F G
6.35 12.7
6.35 12.7
6.35 ✻1 12.7
9.52 ✻2 15.88
9.52 15.88
H(Liquid)
17
17
✻1
✻2
450
H(Gas)
27
27
22 ✻1 29
22 ✻2 29
22 29
50˜150 29
30 640 30
44 75
4
61 227 10
243
10
1 2 6
35
13
81
A
E 13
10
24
Service space:500mm or more
450
Access door
365˜465
159
18
197
55
81
A
C B 81
C
D
B
81
10-ø3(P20/25/32/40/50)
12-ø3(P63/71/80)
10
10
30
Lifting bolt hole
355
56
(14X22)
10-ø3(P20/25/32/40/50)
12-ø3(P63/71/80)
Air inlet
7
288
256
40
176
282
109
179
Air outlet
45 80
277
85
5
3.5
Keep duct-work length 850mm or more.
Be sure to apply the air filter (field supply) near the air inlet grille.
3
In case of bottom inlet
7
Air outlet
10-ø3(P20/25/32/40/50)
12-ø3(P63/71/80)
15
40
176
256
Air inlet
10
81
C
A
B
81
PEFY-P100,125,140VMM-E
Note: 1. On this model, you would use flare nut packed
with the Indoor Unit, when connnecting the
Outdoor Unit for R407C, R22.
2. In order to increase the strength
of the flare nut, the size of some
of them has been increased.
H
1
2
3
4
5
6
7
Refrigerant piping flare connection
(liquid ø9.52 copper tube):HP
Refrigerant piping flare connection
(gas ø15.88 copper tube):LP
ø19.05
Drain 25A (male screw)
Electrical parts box
Drain Pump (Option)
Drain Pipe (Option)···Flexible joint VP25(I.D. ø32)
Filter
Model A B C D E
P100·125 1252 360 370 1310 1284
P140 1552 460 470 1610 1584
In case of rear inlet
Air inlet
25
3 319 3
279
181 40
30
Keep duct-work length 850mm or more.
7
282
Set
F(Liquid) F(Gas)
22 36
22 36
680
53 169
Be sure to apply the air filter (field supply) near the air inlet grille.
450
30
10
35
20
140
210
Service space:500mm or more
450
50˜150 29
Access door
365˜465
122
113
307
45
323
308
4 1 2
6
Air outlet
44
5
197
243
3
55
10
13
75
81
81
A
C B 81
C B 81
A
10
10
E 13
D
12-ø3
30
Lifting bolt hole
(14X22)
375
80
12-ø3
In case of bottom inlet
7
282
Air outlet
12-ø3
30
15
40 181
279
Air inlet
10
81
C B 81
A
50

INDOOR UNIT
Specifications & External Dimensions
PEFY-P VMH-E
Power source
❇ 1
❇ 1
Cooling capacity
❇ 2
❇ 2
❇ 1
Heating capacity ❇ 1
❇ 1
Power consumption Cooling
(50/60Hz) Heating
Cooling
Current
Heating
External finish
Dimension H x W x D
Net weight
Heat exchanger
Type
Airflow rate
Fan (Lo-Hi)
External static 220V
pressure ❇3 230, 240V
Type
Motor
Output ❇ 4
Air filter (option)
Gas
Refrigerant (Flare)
pipe diameter Liquid
(Flare)
Drain pipe diameter
Noise level (Lo-Hi) 220V
❇ 5 230, 240V
mm
in.
kg(lbs.)
m 3 /min
L/s
cfm
Pa
Pa
Specifications
PEFY-P40VMH-E PEFY-P50VMH-E PEFY-P63VMH-E PEFY-P71VMH-E PEFY-P80VMH-E PEFY-P100VMH-E PEFY-P125VMH-E PEFY-P140VMH-E
~ 220-240V 50Hz /60Hz
kW 4.5
5.6
7.1
8.0
9.0
11.2
14.0
16.0
BTU/h 15,400 19,100 24,200 27,300 30,700 38,200 47,800 54,600
kW 4.7 5.8
7.3 8.3
9.3 11.6
14.5 16.3
kcal/h 4,000 5,000
6,300
7,100
8,000 10,000 12,500 14,000
kW 5.0
6.3
8.0
9.0
10.0
12.5
16.0
18.0
kcal/h 4,300 5,400 6,900 7,700
8,600 10,800 13,800 15,500
BTU/h 17,100 21,500 27,300 30,700 34,100 42,700 54,600 61,400
kW
0.19/0.23
0.24/0.30 0.26/0.33 0.32/0.40
0.48/0.58
0.48/0.59
kW
0.19/0.23
0.24/0.30 0.26/0.33 0.32/0.40
0.48/0.58
0.48/0.59
A
0.88/1.06
1.12/1.38 1.20/1.51 1.47/1.83
2.34/2.66
2.35/2.70
A
0.88/1.06
1.12/1.38
2.34/2.66
2.35/2.70
kW
mm(in.)
mm(in.)
dB(A)
dB(A)
1.20/1.51 1.47/1.83
Galvanizing
380 x 750 x 900
15" x 29-9/16" x 35-7/16"
380 x 1,000 x 900
15" x 39-3/8" x 35-7/16"
380 x 1,200 x 900
15" x 47-1/4" x 35-7/16"
44(98)
45(100)
50(111)
70(155)
Cross fin (Aluminum plate fin and copper tube)
Sirocco fan✕ 1
Sirocco fan✕ 2
10.0-14.0
13.5-19.0 15.5-22.0 18.0-25.0
26.5-38.0
28.0-40.0
167-233
225-317 258-367 300-417
442-633
467-667
353-494
477-671 547-777 636-883
936-1342
989-1413
50/100/200
100/150/200
Single phase induction motor
0.08
0.12 0.14
0.18
0.26
Synthethic fiber unwoven cloth filter(long life)
ø 12.7 (1/2")
ø 12.7 (1/2") [R410A]
15.88(5/8")
ø 15.88 (5/8") [R410A]
ø 15.88 (5/8") [R22,R407C]
ø
ø 19.05 (3/4") [R22,R407C]
ø 6.35 (1/4")
ø 6.35(1/4") [R410A]
ø 9.52 (3/8")[R22,R407C]
ø 9.52(3/8")
32 (1-1/4 inch)
32 (1-1/4 inch)
27-34
32-38
32-39
35-41
34-42
31-37
36-41
35-41
38-43
38-44
Note: ❇1 Cooling/Heating capacity indicates the maximum value at operation under the following condition.
Cooling : Indoor 27˚C(80.6˚F)DB/19˚C(66.2˚F)WB,Outdoor 35˚C(95˚F)DB
Heating : Indoor 20˚C(68˚F)DB,Outdoor 7˚C(44.6˚F)DB/6˚C(42.8˚F)WB
❇2 Cooling capacity indicates the maximum value at operation under the following condition.
Cooling : Indoor 27˚C(80.6˚F)DB/19.5˚C(67.1˚F)WB,Outdoor 35˚C(95˚F)DB (WR2: water 30˚C(80˚F))
Heating : Indoor 21˚C(69.8˚F)DB,Outdoor 7˚C(44.6˚F)DB/6˚C(42.8˚F)WB (WR2: water 20˚C(68˚F))
❇3 The external static pressure is set to 100Pa (at 220V) /150Pa (at 230, 240V) at factory shipment.
❇4 The value are that at 240V.
❇5 It is measured in anechoic room.
External Dimensions
PEFY-P40,50,63,71,80, 100,125,140VMH-E
Unit : mm
G-ø3
J-ø3
D
C
70
50x(G-1)=H
F
41
Air inlet
10
Air outlet
15
50
80 50 50x(J-1)=K
B (Lifting bolt pitch)
A
E
Less than 550 mm
Less than 300mm 170mm±5mm
(Actual length)
3
Model:40~80 (Note3)
340
Lifting bolt 383
814 (Lifting bolt pitch)
904
900
3
60
23
250
When installing the drain water lifting-up mech(option).
51
340
45 50x5=250
50
24
847
10
Drain hole
Control box
(option)
2
Terminal bed
1
(Power source)
92
Terminal box Terminal bed
(Transmission)
Keep duct-work length 850mm or more.
Drain hole
17
30
200
343
387
29
15
41 25 50 50 50 50
130 77
328
94
250
380
Model A B C D E
P40VMH-E 800 754 680 600 550
P50VMH-E 800 754 680 600 550
P63VMH-E 800 754 680 600 550
P71·80VMH-E 1050 1004 930 850 800
P100·125
1250 1204 1130 1050 1000
·140VMH-E
F
50
50
50
25
25
G
11
11
11
17
21
✻1 ø12.7 ✻1 ø6.35
780
✻2 ø15.88 ✻2 ø9.52
780 ø15.88 ø9.52
1030 ø15.88 ø9.52
✻1 ø15.88 ✻1 ø9.52
1230
✻2 ø19.05 ✻2 ø9.52
✻1 22 ✻1 29
✻2 22 ✻2 29
22 29
22 29
✻1 22 ✻1 36
✻2 22 ✻2 36
✻1:R410A outdoor unit
✻2:R407C,R22 outdoor unit
Note : 1. Use M10 screw for the lifting bolt (field supply).
2. Keep the service space for the maintenance from the bottom when the heat exchanger is cleaned.
3. This chart indicates for PEFY-P100·125·140VMH-E models, which have 2 fans.
PEFY-P40·50·63·71·80 models have 1 fan.
4. Make sure to install the air filter(field supply) on the air intake side.
In case field supplied air filter is used, attach it where the filter service is easily done.
5.On Model :50, 100, 125, 140, you would use flare nut packed with the Indoor Unit,
when connnecting the Outdoor Unit for R407C, R22.
6.In order to increase the strength of the flare nut, the size of some of them has been increased.
P
Refrigerant piping flare connection (gas M copper tube) : LP ··· ➀
Refrigerant piping flare connection (liquid N copper tube) : HP ··· ➁
Drain hose 32mm(1-1/4inch) (accessory) ··· ➂
H
500
500
500
800
1000
J
10
10
10
15
19
K
450
450
450
700
900
L
780
M
ø12.7
N
ø6.35
P(Liquid)
17
P(Gas)
27

INDOOR UNIT
Specifications & External Dimensions
PEFY-P VMH-E
Specifications
PEFY-P200VMH-E
PEFY-P250VMH-E
Power source
3N ~ 380-415V 50Hz / 60Hz
❇ 1 kW
22.4
28.0
Cooling capacity
❇ 1 BTU/h
76,400
95,500
❇ 2 kW
23.3
29.1
❇ 2 kcal/h
20,000
25,000
❇ 1 kW
25.0
31.5
Heating capacity
❇ 1 kcal/h
21,500
27,100
❇ 1 BTU/h
85,300
107,500
Power consumption Cooling
kW
0.99/1.14
1.23/1.41
(50/60Hz)
Heating
kW
0.99/1.14
1.23/1.41
Cooling
A
1.62/1.86
2.0/2.3
Current
Heating
A
1.62/1.86
2.0/2.3
External finish
Dimension H x W x D mm(in.)
Galvanizing
470 x 1,250 x 1,120 (18-9/ 16 " x 49-1/ 4 " x 44-1/ 8 ")
Net weight
kg(lbs.)
100 (221)
Heat exchanger
Type
Cross fin (Aluminum plate fin and copper tube)
Sirocco fan ✕ 2
m 3 /min
58.0
72.0
Fan
Airflow rate
L/s
967
1200
cfm
2048
2543
External static 380V
Pa
110/220
pressure ❇ 5 400, 415V Pa
130/260
Motor
Type
3-phase induction motor
Output
❇6 kW
0.76
1.08
Air filter (option)
Synthethic fiber unwoven cloth filter(long life)
Gas
mm(in.)
ø 19.05 (3/ 4 ") [R410A]
ø 22.2 (7/ 8 ") [R410A]
Refrigerant
(Brazing)
ø 25.4 (1") [R22,R407C]
ø 28.58 (1-1/ 8 ") [R22,R407C]
pipe diameter
Liquid mm(in.)
ø 9.52 (3/ 8 ") (R410A)
(Brazing)
ø 12.7 (1/ 2 ") (R22,R407C)
Drain pipe diameter
32 (1-1/4 inch)
380V
Noise level
dB(A)
42(110Pa)/45(220Pa)
50(110Pa)/52(220Pa)
❇ 7
400, 415V dB(A)
44(130Pa)/47(260Pa)
52(130Pa)/54(260Pa)
Note: ❇1 Cooling/Heating capacity indicates the maximum value at operation under the following condition. ❇3 The external static pressure is set to 100Pa (at 220V) /150Pa (at 230, 240V) at factory shipment.
Cooling : Indoor 27˚C(80.6˚F)DB/19˚C(66.2˚F)WB,Outdoor 35˚C(95˚F)DB
Heating : Indoor 20˚C(68˚F)DB,Outdoor 7˚C(44.6˚F)DB/6˚C(42.8˚F)WB
❇2 Cooling capacity indicates the maximum value at operation under the following condition.
Cooling : Indoor 27˚C(80.6˚F)DB/19.5˚C(67.1˚F)WB,Outdoor 35˚C(95˚F)DB (WR2: water 30˚C(80˚F))
❇4 The value are that at 240V.
❇5 The external static pressure is set to 110Pa (at 380V) /130Pa (at 400, 415V) at factory shipment.
❇6 The value are that at 415V.
❇7 It is measured in anechoic room.
Heating : Indoor 21˚C(69.8˚F)DB,Outdoor 7˚C(44.6˚F)DB/6˚C(42.8˚F)WB (WR2: water 20˚C(68˚F))
PEFY-P200, 250VMH-E
External Dimensions
Unit : mm
1100
420
1250
102 25
50x21=1050
Lifting bolt
22-ø3
Air inlet
10
21-ø3
Air outlet
15
3
100 50
50x20=1000
23 1326 (Lifting bolt pitch)
1372
1034 (Lifting bolt pitch) 60 340
1124
1100
Note : 1. Use M10 screw for the lifting bolt
(field supply).
2. Keep the service space for the
maintenance from the bottom when
the heat exchanger is cleaned.
3. Make sure to install the air filter(field
supply)on the air intake side.
In case field supplied air filter is
used, attach it where the filter
service is easily done.
4.On this model, you would use pipe
packed with the Indoor Unit, when
connnecting the Outdoor Unit for
R407C, R22.
Model A B
P200VMH-E
P250VMH-E
✻1
✻2
✻1
✻2
ø19.05
ø25.4
ø22.2
ø28.58
✻1
✻2
✻1
✻2
ø9.52
ø12.7
ø9.52
ø12.7
✻1:R410A outdoor unit
✻2:R407C,R22 outdoor unit
Refrigerant piping brazing connection
(gas A copper tube) : LP ····➀
Refrigerant piping brazing connection
(liquid B copper tube) : HP ····➁
Drain hose 32mm(1-1/4inch)
(accessory) ····➂
1120
24
10
1067
Drain hole
(option)
29
15
Control box
20
420
35 50x7= 350
Keep duct-work length 850mm or more.
Terminal bed
(Power source)
Terminal bed
(Transmission)
Drain hole
30
2 1
95 249
422
489
41
164
44
327
20 50x6= 300
105
340
470
Less than 550mm
Less than 300mm
170mm±5mm
(Actual Length)
3
When installing the drain water lifting-up mech(option).
52

INDOOR UNIT
Specifications & External Dimensions
PCFY-P VGM-E
mm(in.)
mm(in.)
Specifications
PCFY-P40VGM-E PCFY-P63VGM-E PCFY-P100VGM-E PCFY-P125VGM-E
Power source
~ 220-240V 50Hz / ~220V 60Hz
❇ 1 kW
4.5
7.1
11.2
14.0
Cooling capacity
❇ 1 BTU/h
15,400
24,200
38,200
47,800
❇ 2 kW
4.7
7.3 11.6
14.5
❇ 2 kcal/h
4,000
6,300
10,000
12,500
❇ 1 kW
5.0
8.0
12.5
16.0
Heating capacity
❇ 1 kcal/h
4,300
6,900
10,800
13,800
❇ 1 BTU/h
17,100
27,300
42,700
54,600
Power
Cooling kW
0.10
0.13
0.16
0.24
consumption
Heating kW
0.10
0.13
0.16
0.24
Current
External finish(Munsel No.)
0.70Y 8.59/0.97
Cooling
A
0.46
0.60
0.73
1.10
Heating
A
0.46
0.60
0.73
1.10
Dimension H x W x D mm 210 x 1,000 x 680 210 x 1,310 x 680 270 x 1,310 x 680 270 x 1,620 x 680
in. 8- 5 / 16 " x 39- 3 / 8 " x 26- 13 / 16 " 8- 5 / 16 " x 51- 5 / 8 " x 26- 13 / 16 " 10- 11 / 16 " x 51- 5 / 8 " x 26- 13 / 16 " 10- 11 / 16 " x 63- 13 / 16 " x 26- 13 / 16 "
Net weight
kg(lbs.)
27(60)
34(75)
37(82)
43(95)
Heat exchanger
Cross fin (Aluminum plate fin and copper tube)
Type
Sirocco fan✕ 2 Sirocco fan✕ 3 Sirocco fan✕ 4
Fan
❇3 m 3 /min 8-10-11-12 12-14-16-18 18-20-23-25 26-28-32-35
Airflow rate
(Lo-Mid2-Mid1-Hi)
L/s 133-167-183-200 200-233-267-300 300-333-383-417 433-467-533-583
cfm 253-353-388-424 424-494-565-636 636-706-812-883 918-989-1130-1236
External staticpressure
Pa
0
Motor
Type
Single phase induction motor
Output
kW
0.054
0.070
0.090
0.150
Air filter
Refrigerant
pipe diameter
Gas(Flare)
Liquid(Flare)
Drain pipe diameter
Noise level (Lo-Mid2-Mid1-Hi) ❇3 ❇4
Note:
dB(A)
ø 12.7( 1 / 2 ")
ø 6.35( 1 / 4 ")
29-33-36-38
❇1 Cooling/Heating capacity indicates the maximum value at operation under the following condition.
Cooling : Indoor 27˚C(80.6˚F)DB/19˚C(66.2˚F)WB,Outdoor 35˚C(95˚F)DB
Heating : Indoor 20˚C(68˚F)DB,Outdoor 7˚C(44.6˚F)DB/6˚C(42.8˚F)WB
❇2 Cooling capacity indicates the maximum value at operation under the following condition.
Cooling : Indoor 27˚C(80.6˚F)DB/19.5˚C(67.1˚F)WB,Outdoor 35˚C(95˚F)DB (WR2: water 30˚C (80˚F))
Heating : Indoor 21˚C(69.8˚F)DB,Outdoor 7˚C(44.6˚F)DB/6˚C(42.8˚F)WB (WR2: water 20˚C (68˚F))
❇3 airflw rate/noise level are shown in (low-middle 2-middle 1-high).
❇4 It is measured in anechoic room.
PP Honeycomb (long life)
ø15.88( 5 / 8 ") ø 15.88( 5 / 8 ") / ø 19.05( 3 / 4 ") (Compatible)
ø 9.52( 3 / 8 ")
I.D. ø26 (VP-25)
32-34-37-39
36-38-41-43
37-39-42-44
PCFY-P40,63,100,125VGM-E
External Dimensions
Unit : mm
150 18
140 70
80
320
Model Liquid Gas
40 ø6.35 ø12.7
63 ø9.52 ø15.88
100,125 ø9.52
ø15.88(R410A)
ø 19.05(R407C,R22)
E
(Suspension bolt pitch)
Electrical box
70
D
16
87
229
Air outlet
506 56
680
81 96
G
F
H
B
A
182
I
J
High press.
Low press.
(Drainage)
254
Air intake
C
161
90
Model A B C D E F G H I J
PCFY -P40VGM-E 1,000 904 918 983 933 210 180 157 201 241
PCFY -P63VGM-E 1,310 1,214 1,228 1,290 1,240 210 180 157 201 241
PCFY -P100VGM-E 1,310 1,214 1,228 1,290 1,240 270 207 217 198 245
PCFY -P125VGM-E 1,620 1,524 1,535 1,600 1,547 270 207 217 198 245
53

MITSUBISHI
PKFY-VAM
MITSUBISHI ELECTRIC
INDOOR UNIT
Specifications & External Dimensions
PKFY-P VAM-E
PKFY-P VGM-E
Specifications
PKFY-P20VAM-E PKFY-P25VAM-E PKFY-P32VGM-E PKFY-P40VGM-E PKFY-P50VGM-E
Power source
~ 220-240V 50Hz ~ 220V 60Hz
❇ 1 kW
2.2 2.8 3.6 4.5
5.6
Cooling capacity
❇ 1 BTU/h
7,500 9,600 12,300
15,400 19,100
❇ 2 kW
2.3 2.9 3.7
4.7
5.8
❇ 2 kcal/h
2,000 2,500 3,150 4,000
5,000
❇ 1 kW
2.5 3.2 4.0 5.0
6.3
Heating capacity
❇ 1 kcal/h
2,200 2,800 3,400
4,300 5,400
❇ 1 BTU/h
8,500 10,900 13,600
17,100 21,500
Power
Cooling kW
0.04
0.07
consumption Heating kW
0.04
0.07
Current
Cooling A
0.20
0.32
Heating A
0.20
0.32
External finish(Munsel
Dimension H x W x D
No.)
mm(in.) 295 x 815 x 158 (11-5/ 8 " x 32-1/ 8 " x 6-1/ 4 ")
Plastic 2.60Y 8.66/0.69
Plastic 0.70Y 8.59/0.97
340 x 990 x 235 (13-7/ 16 " x 39" x 6-5/ 16 ")
white
Net weight
kg(lbs.)
8.5(19)
16(36)
Heat exchanger
Type
Cross fin (Aluminum plate fin and copper tube)
Line flow fan ✕ 1
Fan
❇ 3 m 3 /min
Airflow rate
4.9-5.2-5.6-5.9
8-9.5-10.5-11.5
9-10-11-12
(Lo-Mid2-Mid1-Hi)
L/s
82-87-93-98
133-158-175-192
150-167-183-200
cfm
173-184-198-208
283-335-371-406
318-353-388-424
External static pressure Pa
0
Motor
Type
Single phase induction motor
Output
kW
0.017
0.030
Air filter
PP Honeycomb (long life)
Gas
mm(in.)
ø 12.7(1/2")
ø 12.7(1/ 2 ") / ø 15.88(5/ 8 ")
Refrigerant
(Flare)
(Compatible)
pipe diameter Liquid
mm(in.)
ø 6.35(1/4")
ø 6.35(1/4") / ø 9.52(3/8")
(Flare)
(Compatible)
Drain pipe diameter
I.D. ø16 (VP-16)
I.D. ø20 (VP-20)
Noise level (Lo-Mid2-Mid1-Hi) ❇3 ❇4 dB(A)
32-33-35-36
33-36-38-41
34-37-40-43
Note: ❇ 1 Cooling/Heating capacity indicates the maximum value at operation under the following condition.
Cooling : Indoor 27˚C(80.6˚F)DB/19˚C(66.2˚F)WB,Outdoor 35˚C(95˚F)DB
Heating : Indoor 20˚C(68˚F)DB,Outdoor 7˚C(44.6˚F)DB/6˚C(42.8˚F)WB
❇ 2 Cooling capacity indicates the maximum value at operation under the following condition.
Cooling : Indoor 27˚C(80.6˚F)DB/19.5˚C(67.1˚F)WB,Outdoor 35˚C(95˚F)DB (WR2: water 30˚C(80˚F))
Heating : Indoor 21˚C(69.8˚F)DB,Outdoor 7˚C(44.6˚F)DB/6˚C(42.8˚F)WB (WR2: water 20˚C(68˚F))
❇ 3 Airflow rate/noise level are in (low-middle2-middle1-high).
❇ 4 It is measured in anechoic room.
External Dimensions
295
PKFY-P20, 25VAM-E
783
815
21.5 247.5 Intake dimensions
2.5 60 150
13
630 Intake dimensions 146
695 Outlet dimensions
60
13 25.5
Intake dimensions
Remote control
terminal plate
Power terminal plate
Adress board
PKFY-P32,40,50VGM-E
70 21 245
Left side
60
Knock out hole for
left piping
Refrigerant pipe.
Drain pipe.Wiring hole.
340
53
79
Front view
Lower side
12-Louvers (manual)
715 Air intake
225
340 Air intake 80 280 Air intake
233
990
Auto vane
705 Air outlet
235
160 40
Air intake
198
Right side
235
70 21 245
Address board
Knock out hole for under piping
Refrigerant piping.Drain pipe.
Wiring hole
60
Less than 15
Unit : mm
Knock out hole for
right piping
Refrigerant pipe.
Drain pipe.
Wiring hole
660 (Total length of drain piping 760) 110
80
60
450 Gas pipe
520 Liquid pipe
116
50
400
395
190
70 35
Outlet
angle
Intake
direction
17˚
37.4
Outlet
direction
The address board is protected by
a plastic cover.
Remove the cover with a screwdriver
(one screw) to set the board.
158
5
Installation board
Liquid pipe ø6.35
Gas pipe ø12.7
70.3
Address board
Outlet
dimensions Terminal plate
Rotary switch (pair No.)
Rotary switch (own address)
(Left side piping
35 installation)
Drain pipe (O.D. ø20)
Front view(to open the grille)
Filter grip
Liquid pipe
Gas pipe
700 (Flexible hose total length 800)
153
Model
32,40
50
481 54
549 86
Service panel
(Power supply access)
Terminal block for
remote control
Terminal block for
power supply
(Right side piping
installation)
Liquid pipe Gas pipe
ø6.35 ø12.7
ø 6.35(R410A) ø 12.7(R410A)
ø9.52(R407C,R22) ø15.88(R407C,R22)
31 280
Dip switch (switches functions)
54

INDOOR UNIT
Specifications & External Dimensions
PKFY-P VFM-E
Power source
Cooling capacity
❇ 1
❇ 1
kW
BTU/h
❇ 2 kcal/h
Heating capacity
❇ 1 kW
❇ 1 BTU/h
Power
Cooling kW
consumption Heating kW
Current
Cooling A
Heating A
External finish(Munsel No.)
Dimension
Net weight
Height
Width
Depth
mm(in.)
mm(in.)
mm(in.)
kg(lbs.)
Heat exchanger
Type
Airflow rate ❇ 3
Fan (Lo-Hi)
External static pressure
m 3 /min
Pa
Motor
Air filter
Type
Output
Refrigerant
pipe diameter
Gas
(Flare)
Liquid
(Flare)
kW
mm(in.)
mm(in.)
Specifications
PKFY-P63VFM-E
7.1
24,200
6,300
8.0
27,300
0.12
0.12
0.55
0.55
340(13- 3 /8)
1,400(55- 1 /8)
235(9- 1 /4)
24(53)
Drain pipe diameter
I.D. ø20 (VP-20)
Noise level (Lo-Hi) ❇3 ❇4 dB(A)
39-45
Note: 1. Cooling/heating capacity indicates the maximum value at operation under the following condition.
❇1 Cooling Indoor: 27˚C(80.6˚F)DB/19˚C(66.2˚F)WB, Outdoor: 35˚C(95˚F)DB
Heating Indoor: 20˚C(68˚F)DB, Outdoor: 7˚C(44.6˚F)DB/6˚C(42.8˚F)WB
❇2 Cooling Indoor: 27˚C(80.6˚F)DB/19.5˚C(67.1˚F)WB, Outdoor: 35˚C(95˚F)DB
❇3 Airflow rate/noise level are in (low-high).
❇4 It is measured in anechoic room.
15-20
0.040
ø15.88( 5 /8)
External Dimensions
220-230-240V 50Hz / 220V 60Hz
Plastic, white :
Cross fin (Aluminum plate fin and copper tube)
Line flow fan ✕ 2
0
Single phase induction motor
PP Honeycomb (antibacterial)
ø9.52( 3 /8)
PKFY-P100VFM-E
11.2
38,200
10,000
12.5
42,700
0.14
0.14
0.64
0.64
340(13- 3 /8)
1,680(66- 1 /8)
235(9- 1 /4)
28(62)
Top
PKFY-P63VFM-E PKFY-P100VFM-E Unit : mm
235 45 235 45 235 45
235
13 62.5
235 45 235 45 235 45
22-28
0.070
ø15.88( 5 /8) / ø19.05( 3 /4)
235
41-46
45
235
62.5
13
Left side
1400
1090 Air intake
235
Left side
Front
1680
1370 (Air intake)
Knock out hole
for right piping
Right side
235
A
340
197
C
A
340
197
C
Knock out hole
for left piping
2
42
58
Less than 15
Bolt
Knock out hole
for left piping
2
42
58
Less than 15
Bolt
Drain hose for
left-hand side piping
25
Drain hose
Drain hose 1
55(Gas pipe)
107
120(Liquid pipe)
111
1110 (Drain hose)
183
Lower side louvers(manual)
Auto vanes
1120
240
552Air outlet
552Air outlet
25
Drain hose for
left-hand side piping
Drain hose 1
1110 (Drain hose)
Lower side
1400
694 Air outlet
694 Air outlet
55 (Gas pipe)
120(Liquid pipe) 102
183
111
240
Under panel(Removable at
left-hand side piping)
Knock out hole for under-piping
Refrigerant pipe .Drain pipe
B
louvers(manual) B
Under panel(Removable at
left-hand side piping)
Auto vanes
Knock out hole for under-piping
Refrigerant pipe .Drain pipe
Knock out hole for wiring
B C
A
30
30
Knock out hole for wiring
A
B
C
30 30
55
100
4 39
37
74
Wall fixture
66-ø6 hole
for tapping
screw
32-ø12 hole
for bolt
37
65
39
100
39
98 32 74 37
Drainage range on
left hand side
Drainage range on
Unit center
right-hand side
990
245
455
10X91=(910) 285
900
19
18 18
91
4
184 10
30 30
80 29
60 280
225 240 180 280 314
610 90 Rear piping hole
12-ø6 hole
for tapping screw Range for left rear piping hole
30
100
4 39
37
74
Unit out line
Wall fixture
84-ø6 hole 18 18
for tapping
screw
41-ø12 hole
for bolt
Drainage range on
left hand side
Range for left rear piping hole
39
98
295 225
32
65
37
74 37
Unit center
1270
13X91=(1183)
39
100
4
900
Drainage range on
right-hand side
595
91
245
285
19
10
30
29
30 184
30
80
60 280
240 180 280 314
750
90 Rear piping hole
12-ø6 hole
for tapping screw
Range for left rear piping hole

INDOOR UNIT
Specifications & External Dimensions
New
PFFY-P VKM-E
Specifications
Power source
Cooling capacity
Heating capacity
Power
consumption
Current
Dimension
Cooling
Heating
Cooling
Heating
Height
Width
Depth
❇1
❇1
kW
kW
kW
kW
A
A
mm
mm
mm
PFFY-P20VKM-E
2.2
2.5
0.025
0.025
0.20
0.20
600
700
200
PFFY-P25VKM-E PFFY-P32VKM-E
1-phase 220-240V 50Hz
2.8
3.6
3.2
4.0
0.025
0.025
0.025
0.025
0.20
0.20
0.20
0.20
600
600
700
700
200
200
PFFY-P40VKM-E
4.5
5.0
0.028
0.028
0.24
0.24
600
700
200
Weight
kg
15
15
15
15
Heat exchanger
Type
Airflow rate
Fan (Low-Mid-High-SHi)
External static
pressure
❇2
m 3 /min
Pa
5.9-6.8-7.6-8.7
Cross fin (Alminium plate fin and copper tube)
Line flow fan ✕ 2
6.1-7.0-8.0-9.1
6.1-7.0-8.0-9.1
0
8.0-9.0-9.5-10.7
Motor Type
Output
Air filter
Refrigerant
Gas(Flare)
pipe diameter
Liquid(Flare)
Noise level(Low-Mid-High-SHi) ❇2 ❇3
kW
mm
mm
dB(A)
27-31-34-37
DC motor
0.03 ✕ 2
PP honeycomb fabric (Catechin Filter)
12.7
6.35
28-32-35-38
28-32-35-38
35-38-42-44
Note: 1. Cooling/heating capacity indicates the maximum value at operation under the following condition.
❇1 Cooling Indoor: 27˚C(80.6˚F)DB/19˚C(66.2˚F)WB, Outdoor: 35˚C(95˚F)DB
Heating Indoor: 20˚C(68˚F)DB, Outdoor: 7˚C(44.6˚F)DB/6˚C(42.8˚F)WB
❇2 Airflow rate/noise level are in (Low-Mid-High-SHi).
❇3 It is measured in anechoic room.
External Dimensions
PFFY-P20,25,32,40VKM-E
Unit : mm
4- 6 Hole
131 131
7
Installation plate
46.5
More than
100mm
700
607
46.5
12 200
Air out
Indoor unit
12
363
210 333
593
More than
100mm
More than
100mm
600
Air in
118
96
Gas pipe
12.7(flared)1/2
Liquid pipe
6.35(flared)1/4
337
337
11
Air out
125
60
19
12
60
54
508
137
110
45
35
123
drain
12
60
128
60
19 60
125
165
72
147
205
155 454
60
80
56

INDOOR UNIT
Specifications & External Dimensions
PFFY-P VLEM-E
PFFY-P VLRM-E
Power source
Cooling capacity
Heating capacity
kW
BTU/h
kW
kcal/h
kW
kcal/h
BTU/h
kW
Specifications
PFFY-P20VLEM-E PFFY-P25VLEM-E PFFY-P32VLEM-E PFFY-P40VLEM-E PFFY-P50VLEM-E PFFY-P63VLEM-E
~ 220-240V 50Hz / ~ 208-230V 60Hz
2.2
2.8 3.6 4.5 5.6
7.1
7,500 9,600 12,300 15,400 19,100 24,200
2.3 2.9 3.7
4.7 5.8
7.3
2,000 2,500 3,150 4,000 5,000
6,300
2.5
3.2 4.0 5.0 6.3
8.0
2,200 2,800 3,400
4,300 5,400 6,900
8,500 10,900 13,600 17,100 21,500 27,300
❇ 1
Power
Cooling
0.04 / 0.06
0.06 / 0.07 0.065 / 0.075 0.085 / 0.09 0.1 / 0.11
consumption Heating kW
0.04 / 0.06
0.06 / 0.07 0.065 / 0.075 0.085 / 0.09 0.1 / 0.11
Current
Cooling A
0.19 / 0.25
0.29 / 0.30 0.32 / 0.33 0.40 / 0.41 0.46 / 0.47
Heating A
0.19 / 0.25
0.29 / 0.30 0.32 / 0.33 0.40 / 0.41 0.46 / 0.47
External finish(Munsel No.)
Acrylic paint (5Y 8/1)
Dimension H x W x D mm
630 x 1,050 x 220
630 x 1,170 x 220 630 x 1,410 x 220
Net weight
in. 24-13/ 16 " x 41-3/ 8 " x 8-11/ 16 " 24-13/ 16 " x 46-1/ 8 " x 8-11/ 16 " 24-13/ 16 " x 55-9/ 16 " x 8-11/ 16 "
kg(lbs.)
23(51) 25(56) 26(58) 30(67) 32(71)
Heat exchanger
Cross fin (Aluminum plate fin and copper tube)
Type
Sirocco fan✕ 1
Sirocco fan✕ 2
❇ 3 m 3 /min
7.0-9.0 9.0-11.0 12.0-14.0 12.0-15.5
Fan
Airflow rate
(Low-High)
External static
pressure
Type
Motor
Output
Air filter
Refrigerant
pipe diameter
❇ 1
❇ 1
❇ 2
❇ 2
❇ 1
❇ 1
Gas
(Flare)
Liquid
(Flare)
Drain pipe diameter
Noise level (Low-High) ❇3 ❇4 ❇5
L/s
cfm
Pa
kW
mm(in.)
mm(in.)
dB(A)
5.5-6.5
92-108
194-230
117-150
247-318
150-183
318-388
200-233
424-494
Single phase induction motor
0.015 0.018 0.030
0.035
PP Honeycomb fabric (washable)
ø 12.7 (1/ 2 ")
ø 12.7 (1/ 2 ") [R410A]
ø 15.88 (5/ 8 ") [R22,R407C]
ø 6.35 (1/ 4 ")
ø 6.35 (1/ 4 ") [R410A]
ø 9.52 (3/ 8 ") [R22,R407C]
Accessary hose ø 27 (top end : ø 20)
34-40 35-40 38-43
0
200-258
424-547
0.063
ø 15.88 (5/ 8 ")
ø 9.52 (3/ 8 ")
40-46
57
PFFY-P20VLRM-E PFFY-P25VLRM-E PFFY-P32VLRM-E PFFY-P40VLRM-E PFFY-P50VLRM-E PFFY-P63VLRM-E
Power source
~ 220-240V 50Hz / ~ 208-230V 60Hz
❇ 1 kW
2.2
2.8 3.6 4.5 5.6
7.1
Cooling capacity
❇ 1 BTU/h 7,500 9,600 12,300 15,400 19,100 24,200
❇ 2 kW
2.3 2.9 3.7
4.7 5.8
7.3
❇ 2
❇ 1
kcal/h
kW
2,000
2.5
2,500
3.2
3,150
4.0
4,000
5.0
5,000
6.3
6,300
8.0
Heating capacity ❇ 1 kcal/h 2,200 2,800 3,400
4,300 5,400 6,900
❇ 1 BTU/h 8,500 10,900 13,600 17,100 21,500 27,300
Power
Cooling kW
0.04 / 0.06
0.06 / 0.07 0.065 / 0.075 0.085 / 0.09 0.1 / 0.11
consumption Heating kW
0.04 / 0.06
0.06 / 0.07 0.065 / 0.075 0.085 / 0.09 0.1 / 0.11
Current
Cooling A
0.19 / 0.25
0.29 / 0.30 0.32 / 0.33 0.40 / 0.41 0.46 / 0.47
Heating A
0.19 / 0.25
0.29 / 0.30 0.32 / 0.33 0.40 / 0.41 0.46 / 0.47
External finish(Munsel No.)
Galvanizing
Dimension H x W x D mm
639 x 886 x 220
639 x 1,006 x 220 639 x 1,246 x 220
Net weight
in. 25-3/ 16 " x 34-15/ 16 " x 8-11/ 16 " 25-3/ 16 " x 39-5/ 8 " x 8-11/ 16 " 25-3/ 16 " x 49-1/ 16 " x 8-11/ 16 "
kg(lbs.)
18.5(41) 20(45) 21(47) 25(56) 27(60)
Heat exchanger
Cross fin (Aluminum plate fin and copper tube)
Type
Sirocco fan✕ 1
Sirocco fan✕ 2
❇ 3 m 3 /min
5.5-6.5
7.0-9.0 9.0-11.0 12.0-14.0 12.0-15.5
Airflow rate
Fan (Low-High)
L/s
92-108
117-150 150-183 200-233 200-258
cfm
194-230
247-318 318-388 424-494 424-547
External static
pressure
Pa
0
Motor
Type
Single phase induction motor
Output
kW
0.015 0.018 0.030 0.035
0.063
Air filter
PP Honeycomb fabric (washable)
mm(in.)
ø 12.7 (1/ 2 ")
ø 12.7 (1/ 2 ") [R410A]
ø 15.88 (5/ 8 ")[R22,R407C]
ø 15.88 (5/ 8 ")
Refrigerant
pipe diameter
Gas
(Flare)
Liquid
(Flare)
Drain pipe diameter
Noise level (Low-High) ❇3 ❇4 ❇5
mm(in.)
dB(A)
ø 6.35 (1/ 4 ")
ø 6.35 (1/ 4 ") [R410A]
ø 9.52 (3/ 8 ") [R22,R407C]
Accessary hose ø 27 (top end : ø 20)
34-40 35-40 38-43
Note: ❇1 Cooling/Heating capacity indicates the maximum value at operation under the following condition.
Cooling : Indoor 27˚C(80.6˚F)DB/19˚C(66.2˚F)WB,Outdoor 35˚C(95˚F)DB
Heating : Indoor 20˚C(68˚F)DB,Outdoor 7˚C(44.6˚F)DB/6˚C(42.8˚F)WB
❇2 Cooling capacity indicates the maximum value at operation under the following condition.
Cooling : Indoor 27˚C(80.6˚F)DB/19.5˚C(67.1˚F)WB,Outdoor 35˚C(95˚F)DB (WR2: water 30˚C(80˚F))
Heating : Indoor 21˚C(69.8˚F)DB,Outdoor 7˚C(44.6˚F)DB/6˚C(42.8˚F)WB (WR2: water 20˚C(68˚F))
❇ 3 Air flow rate/noise level are in ( Low-High)
❇ 4 Measured point : 1m51m, Power supply : AC240V/50Hz
·1dB(A) lower at AC230V/50Hz
·2dB(A) lower at AC220V/50Hz
·3dB(A) lower at 1.5m✕1.5m point
❇ 5 It is measured in anechoic room.
ø 9.52 (3/ 8 ")
40-46

INDOOR UNIT
Specifications & External Dimensions
PFFY-P VLEM-E
PFFY-P VLRM-E
External Dimensions
PFFY-P20,25,32,40,50,63VLEM-E
Note: 1. On Model :50, you would use flare nut
packed with the Indoor Unit, when
connnecting the Outdoor Unit for R407C,
R22.
2. In order to increase the strength of the flare
nut, the size of some of them has been
G
(60)
40 120
Air supply grille
Unit : mm
Remote controller
can be built-in.
(Program timer can not be
built-in together)
Air outlet
C
A
220
80
B
170
50
100
35
35
20
Refrigerant piping flare
connection(Gas) E : LP
Refrigeant piping flare
connection(Liquid) F : HP
Drain pan
Strainer
78
15
15
160
310 108
2 ✕ 2-12 ✕16
Wall mounting hole
Note: 1. On Model :50, you would use flare nut packed with the Indoor
Unit, when connnecting the Outdoor Unit for R407C, R22.
2. In order to increase the strength of the flare nut, the size of
some of them has been increased.
J
B
132 15
Air outlet
A
167
2- ø 4.7
Duct mounting hole
220
98 30
49
35
8
Refrigerant piping flare
connection(Gas) G : LP
Refrigeant piping flare
connection(Liquid) H : HP
Drain pan
Strainer
2 ✕ F - ø 4.7
Duct mounting hole
80
2 ✕ 2 - 12 ✕ 16
Wall mounting hole
310 90
300
400
Hose(accessory)
OD ø 27(TOP ø 20)
170
639
630
430
Level adjusting screw
4 pcs.(attached)
Air
inlet
90
( 75 ) 500
6
Hose(accessory)
OD ø 27(TOP ø 20)
10
220
45
Air filter
D
220
170 300
10
Dimensions
Model A B C D E(Gas) F(Liquid)
PFFY-P20VLEM-E 1050 640 600 610 ø12.7 ø6.35
PFFY-P25VLEM-E 1050
PFFY-P32VLEM-E 1170
640
760
600
720
610
730
ø12.7
ø12.7
ø6.35
ø6.35
PFFY-P40VLEM-E 1170 760 720 730 ø12.7 ø6.35
PFFY-P50VLEM-E 1410 1000 960
✻1 ø12.7 ✻1 ø6.35
970
✻2 ø15.88 ✻2 ø9.52
PFFY-P63VLEM-E 1410 1000 960 970 ø15.88 ø9.52
G(Liquid)
17
✻1
✻2
17
17
17
22
22
22
G(Gas)
27
✻1
✻2
27
27
27
29
29
29
183.5 21
25
170
Piping
space
✻1:R410A outdoor unit
✻2:R407C,R22 outdoor unit
B
2-12 ✕16
Floor mounting hole
106
PFFY-P20,25,32,40,50,63VLRM-E
50
84
100
10
29
120
C
E
430
Level adjusting screw
4 pcs.(attached)
Air
inlet
Dimensions
Model A B C D E F G(Gas) H(Liquid)
PFFY-P20VLRM-E 886 640 572 610 360 4 ø12.7 ø6.35
PFFY-P25VLRM-E 886 640 572 610 360 4 ø12.7 ø6.35
PFFY-P32VLRM-E 1006 760 692 730 480 5 ø12.7 ø6.35
PFFY-P40VLRM-E 1006 760 692 730 480 5 ø12.7 ø6.35
PFFY-P50VLRM-E 1246 1000 932 970 720
✻1 ø12.7 ✻1 ø6.35
7
✻2 ø15.88 ✻2 ø9.52
PFFY-P63VLRM-E 1246 1000 932 970 720 7 ø15.88 ø9.52
✻1:R410A outdoor unit
✻2:R407C,R22 outdoor unit
90
9
( 75 )
J(Liquid) J(Gas)
17 27
17
17
17
27
27
27
✻1
✻2
22
22
✻1
✻2
29
29
22 29
Air filter
15
45
76 D
B
15
2-12 ✕ 16
Floor mounting hole
106
58

INDOOR UNIT
Specifications & External Dimensions
PEFY-P VMH-E-F
(Fresh Air Intake Type)
Power source
Cooling capacity
Heating capacity
Power consumption
(50/60Hz)
Current
External finish
Dimension
Net weight
Heat exchanger
Type
Airflow rate
Fan
Motor
External
static
pressure
(Low/Mid/High)
Type
Output
❇1
❇1
❇1
❇1
Cooling
Heating
Cooling
Heating
Height
Width
Depth
208V
220V
230V
240V
Heat pump models
Cooling only
110%(100% in case of heating below-5˚C(23˚F) 110%
PEFY-P80, 140VMH-E-F
kW
BTU/h
kW
BTU/h
kW
kW
A
A
mm(in.)
mm(in.)
mm(in.)
kg(lbs.)
m 3 /min
L/s
cfm
Pa
Pa
Pa
Pa
kW
Specifications
PEFY-P80VMH-E-F
PEFY-P140VMH-E-F
~ 220-240V 50Hz / ~ 208-230V 60Hz
9.0 16.0
30,700
8.5
54,600
15.1
29,000
51,500
0.16/0.21
0.29/0.33
0.16/0.21
0.29/0.33
0.67/0.91
1.24/1.48
0.67/0.91
1.24/1.48
Galvanizing
380(15")
1000(39-3/ 8 ") 1200(47- 1 / 4 ")
900(35- 7 / 16 ")
50(111") 70(155")
Cross fin (Aluminum plate fin and copper tube)
Sirocco fan✕ 1
Sirocco fan✕ 2
9.0
18.0
150
300
18
636
35/85/170 35/85/170
40/115/190 50/115/190
50/130/210 60/130/220
80/170/220 100/170/240
Single phase induction motor
0.09 0.14
Synthetic fiber unwoven cloth filter(long life)
ø 15.88 (5/ 8 ") [R410A] / 19.05 (3/ 4 ") [R22,R407C]
Air filter (option)
Refrigerant
Gas(Flare) mm(in.)
ø 15.88( 5 / 8 ")
pipe diameter
Liquid(Flare) mm(in.)
ø 9.52(3/ 8 ")
Drain pipe diameter
32 (1-1/4 inch)
208, 220V dB(A)
27/38/43
Noise level
❇2
230, 240V dB(A)
33/43/45
Note: ❇1 Cooling/Heating capacity indicates the maximum value at operation under the following condition.
Cooling : Indoor 33˚C(91.4˚F)DB/28˚C(82.4˚F)WB,Outdoor 33˚C(91.4˚F)DB
Heating : Indoor 0˚C(32˚F)DB/-2.9˚C(26.8˚F)WB,Outdoor 0˚C(32˚F)DB/-2.9˚C(26.8˚F)WB
❇2 It is measured in anechoic room.
a ). The cooling and heating capacities are the maximum capacities that were obtained by operating in the above air conditions and with a refrigerant pipe of about 7.5m(24- 5 / 8 Ft).
b ). The actual capacity characteristics vary with the combination of indoor and outdoor units. See the technical information.
c ). The operating noise is the data that was obtained by measuring it 1.5m(4-15/ 16 Ft) from the bottom of the unit in an anechoic room. (Noise meter A-scale value)
d ). The figure of Electrical characteristic indicates at 220V and at middle external static pressure.
e ). When the 100% fresh air indoor units are connected, the maximum connectable indoor units to 1 outdoor unit are as follows.
f ). Operational temp range is cooling : from 21˚C(61.8˚F)DB/15.5˚C (59.9˚F)WB to 43˚C(109.4˚F)DB/35˚C(95˚F)WB.
Heating : from -10˚C(14˚F)DB to 20˚C(68˚F)DB
✻Thermo off (Fan) operation automatically starts either when temperature is lower than 21˚C(69.8˚F)DB in cooling mode or when the temperature exceeds 20˚C(68˚F)DB in heating mode.
g).As the room temp is sensed by the thermo in the remote controller or the one in the room, be sure to use ether remote controller or room thermo.
h).Dry mode is Not available. Fan mode operation during the thermo off in Cooling/Heating mode.
i ). The fan would temporarily stops either with R2/WR2 system or in defrost.
j ). In any case, the air flow rate should be kept lower than 110% of the above chart.Please see “ Fan curves “ for the details.
k).When this unit is used as sole A/C system, be careful about the dew in air outlet grilles in cooling mode.
l).Un-conditioned outdoor air such as humid air or cold air blows to the indoor during thermo off operation. Please be careful when positioning indoor unit air outlet grilles, ie take the necessary precautions for cold air, and also
insulate rooms for dew condensation prevention as required.
m). Air filter must be installed in the air intake side.The filter should be attached where easy maintenance is possible in case of usage of field supply filters.
n). Long life filter cannot be used together with Hi-efficiency filter.
External Dimensions
28/38/43
34/43/45
Required space for service and maintenance
Unit : mm
625
G-ø3
J-ø3
100~200
700
150~200
450
Access door
450
50
50
L
Note2
D
C
50x(G-1)=H
Air inlet
Air outlet
50x(J-1)=K
B (Lifting bolt pitch)
A
E
Access door Ceiling surface
Make the access door at the appointed position
properly for service maintenance.
More than 20mm
More than 20mm
50
50
Less than 300mm
170mm±5mm (Actual length)
41 F
10
15
80
70
Model:80(Note3)
340
Lifting bolt
383
814 (Lifting bolt pitch)
904
3
60
23
250
Less than 550mm
3
59
900
24
847
10
Drain hole
Control box (option)
2
Terminal bed
1
(Power source)
92 200
Terminal box Terminal bed
343
(Transmission)
Keep duct-work length 850mm or more.
387
Drain hole
17 340
45 50x5=250
50
30
29
15
50 50 50 50
77
328
250
380
41 25
130
94
Model
PEFY-P80VMH-E-F
PEFY-P140VMH-E-F
A
1050
1250
B
1004
1204
Note
When installing the drain
water lifting-up mech(option).
1.Use M10 screw for the lifting bolt (field supply).
2.Keep the service space for the maintenance from the bottom when the heat exchanger is cleaned.
3.This chart indicates for PEFY-P140VMH-E-F models, which have 2 fans.
PEFY-P80VMH-E-F model has 1 fan.
4.Make sure to install the air filter(field supply) on the air intake side.
In case field supplied air filter is used, attach it where the filter service is easily done.
5.On Model :140, you would use flare nut packed with the Indoor Unit,
when connnecting the Outdoor Unit for R407C, R22.
6.In order to increase the strength of the flare nut,
P
the size of some of them has been increased.
Refrigerant piping flare connection(gas M copper tube):LP ······ ➀
Refrigerant piping flare connection(liquid N copper tube):HP ······ ➁
Drain hose 32mm(1-1/4inch) (accessory) ······ ➂
C D E F G H J K L M N P(Liquid) P(Gas)
930 850 800 25 17 800 15 700 1030 ø15.88 ø9.52 22 29
✻1 ø15.88
✻1:R410A outdoor unit
1130 1050 1000 25 21 1000 19 900 1230
ø9.52 22 36
✻2 ø19.05
✻2:R407C,R22 outdoor unit

INDOOR UNIT
Specifications & External Dimensions
PEFY-P VMH-E-F
(Fresh Air Intake Type)
Power source
Cooling capacity
Heating capacity
Power consumption
(50/60Hz)
Current
External finish
Dimension
Net weight
Heat exchanger
Type
Airflow rate
Fan
External
static
pressure
Type
Motor
Output
Air filter (option)
Refrigerant
pipe diameter
Drain pipe diameter
Noise level
Cooling
Heating
Cooling
Heating
Height
Width
Depth
380V
400V
415V
Gas
(Flare)
Liquid
(Flare)
380V
400V
415V
PEFY-P200, 250VMH-E-F
kW
BTU/h
kW
BTU/h
kW
kW
A
A
mm(in.)
mm(in.)
mm(in.)
kg(lbs.)
m 3 /min
L/s
cfm
Pa
Pa
Pa
kW
mm(in.)
mm(in.)
dB(A)
dB(A)
dB(A)
Specifications
PEFY-P200VMH-E-F
PEFY-P250 VMH-E-F
3N~ 380-415V 50Hz / 60Hz
22.4 28.0
76,400 95,500
21.2
26.5
72,300 90,400
0.34/0.42
0.39/0.50
0.34/0.42
0.39/0.50
0.58/0.74
0.68/0.86
0.58/0.74
0.68/0.86
Galvanized
470 (18-9/16")
1250 (49-1/4")
1120 (44-1/8")
100 (221")
Cross fin
Sirocco fan ✕ 2
28
35
467
583
989
1236
140/200 110/190
150/210 120/200
160/220 130/210
3-phase induction motor
0.20 0.23
Synthetic fiber unmoven cloth filter (long life type)
ø 19.05 ( 3 /4") [R410A]
ø 22.2 ( 7 /8") [R410A]
ø 25.4 (1") [R22,R407C]
ø 28.58 (1- 1 /8") [R22,R407C]
ø9.52 (3/8") [R410A]
ø9.52 ( 3/8") [R410A]
ø 12.7 (1/2") [R22,R407C]
ø 12.7 (1/2") [R22,R407C]
Unit drain pipe I.D 32 (1-1/4 inch)
39/42
40/44
40/43
40/45
40/44
41/46
Note: 1. The cooling amd heating capacites are the maximum capacites that were obitained by operating in the above air conditions and with a refrigerant pipe of about 7.5m.
2 .The actual capacity characteristics vary with the combination of indoor and outdoor units. See the technical infomation.
3 .The operating noise is the data that was obitained by measuring it 1.5m from the the bottom of the unit in an anechoic room. (Noise meter A-scale value)
4 .The figure of Electrical characteristic , indicates at 220 Pa setting at 415V.
5 . When the 100% fresh air indoor units are connected, the maximum connectable indoor units to 1 outdoor unit are as follows.
Heat pump models
Cooling only
110%(100% in case of heating below-5˚C(23˚F)) 110%
6. Operational temp range is Cooling:from 21˚C(69.8˚F)DB/15.5˚C(59.9˚F)WB to 43˚C(109.4˚F)DB/35˚C(95˚F)WB
Heating: from -10˚C(14˚F)DB to 20˚C(68˚F)DB.
❇ Thermo off(Fan) operation automatically starts either when temperature is lower than 21˚C(69.8˚F)DB in cooling mode or when the temperature exceeds 20˚C(68˚F)DB in heating mode.
7. As the room temp in sensed by the thermo in the remote controller or the one in the room, be sure to use either remote controller or room thermo.
8. Autochangeover function or Dry mode is NOT available. Fan mode operation during the thermo off in Cooling/Heating mode.
9. The fan would temporaly stops either with R2/WR2 system or in defrost.
10. In any case, the air flow rate should be kept lower than 110% of the above chart. Please see "Fan curves" for the details.
11. When this nit is used as sole A/C system, be careful about the dew in air outlet grilles in cooling mode.
12. Un-conditioned outdoor air such as humid air or cold air blows to the indoor during thermo off operation.
Please be careful when positioning indoor unit air outlet grilles, ie take the necessary precautions for cold air, and also insulate rooms for dew condensation prevention as required.
13. Air filter must be installed in the air intake side. The filter should be attached where easy maintenance in possible in case of usage of fild supply filters.
22-ø3
External Dimensions
22-ø3
Required space for service and maintenance
Unit : mm
730
1100
1250
50x21=1050
Air outlet
Air outlet
50x20=1000
1326(Lifting bolt pitch)
1372
1100
200~300
800
150~200
450
Access door
450
50
50
1350
Note2
More than 20
25
102
10
15
50
100
Access door Ceiling surface
Make the access door at the appointed position properly maintenance.
More than 20
420
Lifting bolt
4-14X30
420
50x7=350
20
35
24
10
Keep duct-work length 850mm or more.
Control box
Terminal bed
(Power source)
Terminal bed
(Transmission)
170 - + 5
30
78
3
1034(Lifting bolt pitch) 60 340
1124
1120
1067
29
15
Drain hole
(option)
Drain hole
2 1
95 249
422
489
44
327
50x6=300
340
470
41
164
23
20
105
Less than 550
When installing the drain water lifting-up
Less than 300
170mm+5mm (Actual length)
Refrigerant piping brazing connection(gas A copper tube):LP ······ ➀
Refrigerant piping brazing connection(liquid B copper tube):HP ······ ➁
Drain hose 32mm(1-1/4inch) (accessory) ······ ➂
3
Model A B
PEFY-P200VMH-E-F ✻1 ø19.05 ✻1 ø9.52
✻2 ø25.4 ✻2 ø12.7
PEFY-P250VMH-E-F ✻1 ø22.2 ✻1 ø9.52
✻2 ø28.58 ✻2 ø12.7
✻1:R410A outdoor unit ✻2:The other outdoor unit
Note 1. Use M10 screw for the lifting bolt (field supply).
2.Keep the service space for maintenance from
the bottom
when the heat exchanger is cleaned.
3.Make sure to install the air filter (field supply) on
the air intake side.
In case field supplied air filter is used, attach it
where the filter service is easily done.
4.On this model, you would use pipe
packed with the Indoor Unit, when connnecting
the Outdoor Unit for R407C, R22.
60

0
Fresh cool air(outdoor)
5.2
Stale hot air (exhaust)
The Ventilation System for Enhanced Air Quality - Lossnay
Combine with Lossnay Ventilation System Enhanced Air Quality.
Unified Control System Allows Greater Design Freedom.
Heat-Exchange Efficiency Obtainable Only with Lossnay.
The secret to the unmatched comfort provided Lossnay core is the crossflow,
plate-fin structure off the heat-exchange unit. A diaphragm made of a
specially processed paper fully separates inducted and exhausted air
supplies, ensuring that only fresh air is introduced to the indoor environment.
The superior heat-transfer and moisture permeability of the special paper
assure highly effective total heat exchange (temperature and humidity) when
inducted ? and exhausted air supplies cross in the Lossnay core.
20
Stale warm air (indoor air)
Lossnay Element
Construction & Principle
Stale air exhaust
(dirty indoor air)
EA
Outdoors
Fresh air exhaust
(fresh heating / cooling air)
SA
Indoors
14.8
Fresh warm air (indoor supply air)
OA
Fresh air induction
(fresh air)
RA
Stale air induction
(dirty heating / cooling air)
LGH-15RX4
LGH-25RX4
LGH-35RX4
LGH-50RX4
LGH-65RX4
LGH-80RX4
LGH-100RX4
LGH-150RX4
LGH-200RX4
[150m 3 /h Single phase 220-240V 50/60Hz]
[250m 3 /h Single phase 220-240V 50/60Hz]
[350m 3 /h Single phase 220-240V 50/60Hz]
[500m 3 /h Single phase 220-240V 50/60Hz]
[650m 3 /h Single phase 220-240V 50/60Hz]
[800m 3 /h Single phase 220-240V 50/60Hz]
[1000m 3 /h Single phase 220-240V 50/60Hz]
[1500m 3 /h Single phase 220-240V 50/60Hz]
[2000m 3 /h Single phase 220-240V 50/60Hz]
OA Processing Units
Ideal Indoor-Air Quality — For Your Comfort and Health
The OA (outdoor-air) Processing Unit creates an optimum indoor-air environment at an unparalleled rate of cost efficiency providing substantial
energy savings. Forced air ventilating and humidifying functions unique to this system keep indoor-air fresh and free of contaminants preventing
“sick building syndrome” and the spread of airborne viruses such as the flu. Another novel feature of the OA Processing Unit is the “Lossnay
core,” a heat-exchange unit that functions to transfer heat efficiently, cutting ventilation load by as much as 70%. This special combination of
functionality
and performance designed to ensure users ample comfort and year-round health cannot be found anywhere else on the market.
EA (Exhaust air)
Heat from the indoor air (both sensible
and latent) is recovered by the Lossnay
OA (Outdoor air)
Core and vented outside by the
Fresh, outdoor-air in a quantity exhaust fan.
required for ventilation is drawn
in by the supply fan.
The exhaust fan
High efficiency filters (Option)
The supply fan
OA Processing Units
61
Heat recovery unit
(Lossnay Core)
Temperature and humidity are
exchanged between the supply
air and the exhaust air.
Maintenance cover
Air filter
Prevents clogs in
the Lossnay Core.
DX Heat exchanger
Cools or heats the drawn
in outdoor-air.
SA (Supply air)
The processed, fresh
outdoor-air is vented
to the indoor rooms.
RA (Return air)
The exhaust
fan draws in
contaminated
indoor-air.
GUF-50RD(H)3 *1
Cooling Capacity
5.29 (DX coil:3.63, Lossnay:1.66)KW
Heating capacity
6.42 (DX coil:4.17, Lossnay:2.25)KW
500m 3 /h Single phase 220-240V 50Hz
GUF-100RD(H)3 *1
Cooling Capacity
10.81 (DX coil:7.32, Lossnay3.49)KW
Heating capacity
13.00 (DX coil:8.30, Lossnay:4.70)KW
1000m 3 /h Single phase 220-240V 50Hz
*1 H : Humidifying Type

Y : PUHY
R2 : PURY
WY : PQHY
WR2 : PQRY
S : PUMY
INDOOR UNIT
PLFY-VAM / VCM PCFY-VGM
PLFY-VLMD
PKFY-VAM / VGM / VFM
PMFY-VBM
PFFY-VKM
PEFY-VMS
PFFY-VLRM / VLEM
PEFY-VMR
Fresh Air Intake type
PEFY-VML / VMM / VMH
LONWORKS
62

Integrated Communications Control with Mitsubishi's Unique Transmission Network(M-NET)
Operation
Start / Stop
Operation mode
Temperature setting
Permit / Prohibit direction
Fan speed
Air flow direction
ON/OFF
Model
No. of units controllable
(Groups (G) / units)
Error flashing
Local remote controller
System controller
Simple Wireless ON/OFF Group System
Remote controller
Schedule
remote remote remote remote remote
Centralized controller
timer
controller controller controller controller controller
PAR-21MAA PAR-F27MEA PAC-SE/YT51CRA PAR-FA32MA PAR-FL32MA PAC-YT40ANRA PAC-SC30GRA PAC-SF44SRA PAC-YT34STA G-50A GB-50A TG-2000A
50G/50units 50G/50units
1G/16units 1G/16units 1G/16units 1G/16units 16/50 8G/16units 50/50 50G/50U 2000G/2000units
G-50A browser GB-50A browser
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
*4
*4
*4
✕
✕
✕
✕
✕
63
Monitoring
Scheduling
Recording
Others
Control and
management
Operation
Monitoring
Error content
Filter sign
Operating hour
Operation mode
Set temperature
Indoor temperature (intake)
Permit / Prohibit
Fan speed
Air flow direction
Weekly
Annual (Designated day setting)
One day
Times of stops / Starts per day
Times of stops / Starts per week
Auto off timer
Minimum setting unit (minutes)
Error history
Daily / Monthly reports
Electricity charges
Set temperature range limit
Auto lock
Ventilation (group / interlocked)
Group setting
Block setting
Revision of electricity charges
Ventilation
(group / interlocked)
Ventilation
(group / interlocked)
Start / Stop
Fan speed
Ventilation mode
Status
Fan speed
Ventilation mode
✕
✕
8 *5
56
1 *5
✕
✕
✕
✕ /
✕
✕
*5
*1
✕
✕
✕
1/1
✕
10 *5
✕
✕
✕
✕ /
✕
✕
: Each group / Batched : Each group : Block (City Multi indoor unit only)
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
: Batched handling (for maintenance) : Batched only ✕ : Not available – : Not used : G-50A license registration possible.
*1: For group operation, cross-over wring is required between indoor unit. *2: Installation possible at Initial setting tool.
*3: Interlock setting from local remote controller. *4: From schedule setting *5: When PAC-YT32PTA is connected.
✕
✕
✕
✕
✕
✕
✕
✕
✕
1/1
✕
✕
10
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
/ ✕
✕
✕
*3
/
✕
✕
✕
✕
✕
✕
✕ / * 5
✕
✕
*
✕ /48
5
*
✕ /336
5
✕
* 5 ✕ /30
✕
✕
✕
✕
✕ /
✕
✕
– /
– /
– / ✕
– /
– /
– / ✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
/
/
/ ✕
/
/
/ ✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
16
112
✕
5
✕
✕
✕
✕
✕
✕
✕
/
✕
✕
✕
✕
✕
✕
✕
✕
3/3
21/21
✕
10
✕
✕
✕
✕
✕
✕
/
/
/ ✕
/
/
/ ✕
✕
12
84
✕
1
✕
✕
✕
/
✕
/
/
/ ✕
/
/
*2
*2
*2
*2
/ ✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
✕
/
/
✕
✕
✕
✕
✕
12
84
✕
1
✕
✕
✕
/
✕
/
/
/ ✕
/
/
*2
*2
*2
*2
/ ✕
12
84
✕
1
✕
/
/
/
/ ✕
/
/
/ ✕

Building Air conditioning
control system
HAND-HELD
REMOTE CONTROLLER
MA REMOTE CONTROLLER PAR-21MAA
Example of system configuration
M-NET
Non-polarized
2-wire
MA remote controller
Non-polarized
2-wire
MA remote controller
High-quality pure-white color body
Dot liquid-crystal display is applied
Symbols, Japanese, Chinese, English, Germany,Spanish, Russian,
Italian, French display can be selected freely.
TM
Connectable to all CITYMULTI indoor unit, and
automatically adjust its function with the indoor unit
connected
Limiting temperature setting range is possible
Help to avoid over-cooling or over-heating. Save energy.
Auto-stop timer is available
Help to avoid forgetting to stop the air conditioner.
Weekly scheduler is available
ON/OFF/Temperature setting 8 times per day, 1 week scheduling.
Grouping via cross-over wire directly
Usable as the local remote controller for system controller
(MELANS)
Combining ME remote controller and/or LOSSNAY remote
controller in a group is not possible.
LCD temperature setting and display in
1˚C /1˚F unit.
ME REMOTE CONTROLLER PAR-F27MEA
Example of system configuration
ME remote controller
ME remote controller
Easy to read, easy to operate icon display
Temperature selection
Room air temperature display
Outlet angle display
Displays the angle of blowing between 20˚ and 70˚. (Only for cassette
model PL and PK. Ceiling mounted models display the air volume
ratio.)
Auto-diagnosis display
A microcomputer constantly monitors operation to keep the units
running smoothly. Should problems occur, the temperature setting
display changes to an auto-diagnosis display that shows the
inspection mode and the unit address alternately.
Standardized remote controllers for all indoor units
All wiring is simply done with non-polarized two-wire signal
lines
Room thermometer is built into the remote controller
Daily timer
Repeated ON / OFF timer every day.
Auto OFF timer
0:30, 1:00, 1:30, 2:00...4:00 one touch timer.
Function lock
All functions or all functions except ON / OFF can be selected.
Limit setting of room temperature.
64

Building Air conditioning
control system
HAND-HELD
REMOTE CONTROLLER
SIMPLE MA REMOTE CONTROLLER PAC-YT51CRA
PAC-YT51CRA
To simplify operation of the system, the range of controls has been
limited to START/STOP, room temperature and fan speed
The only wiring required is cross-over wiring based on two-wire
signal lines
Room temperature sensors are built-in. The indoor unit can be
replaced with body thermostats
Easy to read, easy to operate icon display
LCD temperature setting and display in
1˚C /1˚F unit.
Can operate all types of indoor units
Standardized remote controllers for all indoor units
*Since this system has no operation mode switching, test operation, selfdiagnosis
or interlock setting functions, it should always be used in conjunction
with the PAR-21MAA or other centralized controller.
*Combining ME remote controller and/or LOSSNAY remote
controller in a group is not possible.
WIRELESS REMOTE CONTROLLER PAR-FL32MA / PAR-FA32MA
• Wireless construction supports multi - systems in
buildings.
• No need to configure addresses for group operation.
• Lit LED keeps you informed of operation - blinking even
gives you the error code via the number of blinks.
• Can be used with the MA remote controller.
*When used in group configurations, wiring between indoor units is
required.
*Combining ME remote controller and/or LOSSNAY remote
controller in a group is not possible.
• LCD temperature setting and display in 1˚C /1˚F unit.
PAR-FL32MA
PAR-FA32MA
65

UP
UP
POWER SUPPLY UNIT
MODEL PAC-SC50KUA
POWER RATING
WEIGHT
2.11kg
SERIAL No.
MITSUBISHI ELECTRIC CORPORATION
POWER SUPPLY UNIT
MODEL PAC-SC50KUA
POWER RATING
WEIGHT
2.11kg
SERIAL No.
MITSUBISHI ELECTRIC CORPORATION
Building Air conditioning
control system
CENTRALIZED
REMOTE CONTROLLER
CENTRAL CONTROLLER G-50A/GB-50A
Up to 50 units of packaged air conditioners can freely be monitored
and operated!
Furthermore, it has enabled the Monitoring and Operation Via a
Web Browser on a Personal Computer connected to it using a LAN
or telephone line!
First in the industry
With Web Server
Functions!
G-50A (with display)
GB-50A
Simple and Flexible
This new generation controller is suitable for small to large systems
with simple to complex functions available.
Web Browser
Enables monitoring and operation of air conditioning units using a PC
with Microsoft ® Internet Explorer.
Remote Access
Allows users to remotely monitor and operate the air conditioning
units using a PC connected to a telephone line.
Auto Alarm
In the case of any malfunction, necessary information will be sent to a
mobile phone and/or personal computer by e-mail.
Easy to Upgrade
Various new functions will be introduced gradually and can easily be
down loaded into any existing G-50A/GB-50A.
Example: Energy Monitoring
Demand Control
Annual Schedule
Example of display icons (air conditioner icons)
Operation
In timer operation
Stop
Lossnay on
Occurrence of
abnormality
Under energy-saving
control
Operation/
Occurrence of a filter sign
System Structure
Remote monitoring via a
Web browser
Web browser
G-50A
City Multi
outdoor unit
M-NET
Public telephone
line
Provider
Router
Ethernet
Power supply unit
PAC-SC50KUA
City Multi
Provider
GB-50A
City Multi
outdoor unit
M-NET
Power supply unit
PAC-SC50KUA
City Multi
* Microsoft is a trademark or trademark of Microsoft corporation.
66

UP
Building Air conditioning
control system
CENTRALIZED
REMOTE CONTROLLER
GROUP REMOTE CONTROLLER PAC-SC30GRA
Up to 8 groups can be operated (maximum of 16 units). Just by
pressing switches, groups can be started and stopped
individually, or all groups can be started and stopped as a
batch.
Detailed settings and operations can also be made for each
individual group.
All the wiring is simply done with non-polarized two wire signal
lines. The connection is the same as the connection to the
master system controller.
It supports operation of groups that can extend beyond one
refrigerant system. Furthermore, it is possible to drive
interlocked systems that use ventilator equipment or drive
ventilator equipment in a stand-alone situation.
*With the group remote controller, you cannot control groups that
only contain the LOSSNAY remote controller.
*It is impossible to use the group remote controller to control K
control units.
*When connecting to signal cables for central control, it must use a
power supply unit for the signal cables.
System example
Connect to the centralized transmission line
Group remote
controller
Power supply
unit
MA R/C
MA R/C
R/C:Remote Controller
Connect to the indoor/outdoor transmission line
67
R/C:Remote Controller
Group remote
controller
MA R/C
MA R/C

UP
Building Air conditioning
control system
CENTRALIZED
REMOTE CONTROLLER
SYSTEM REMOTE CONTROLLER PAC-SF44SRA
50 groups/50 units of air conditioners can be controlled
Up to 50 groups/50 units of air conditioners can be operated with one remote
controller.
A general-purpose interface is available for control, so general devices can also be
turned ON and OFF.
Operation status displayed on easy-to-read LCD
The group currently operating can be seen at a glance with the operation status
display for each group.
Independent LOSSNAY operation is possible
LOSSNAY units can be grouped the same as the Central remote controller and
ON/OFF remote controller.
"Automatic ventilation", "Normal ventilation" and "Ventilation with heat
exchanger" can be switched from the system controller.
Simple remote controller limited to basic operations.
The only operations required for the air conditioner are "ON/OFF", "Operation
mode changeover", "Temperature setting" and "Prohibit operation by local remote
controller", so anyone can easilyoperate the unit.
Using collective control from the system remotecontroller, operation mode settings
using the local remote controllers can be prohibited.
(Operation mode limit function)
Schedule operation is available
Groups of air conditioners are available for operation at a set schedule using the
Schedule timer (PAC-YT34STA).
System example
System
remote
controller
Power
supply
unit
MA R/C
MA R/C
LOSSNAY
PZ-52SF
LOSSNAY
LOSSNAY
PZ-52SF
R/C:Remote Controller
68

UP
Building Air conditioning
control system
CENTRALIZED
REMOTE CONTROLLER
Schedule timer PAC-YT34STA
The weekly schedule of up to 50 groups/50 units can be
controlled with one schedule timer.
General-purpose devices can also be turned ON and OFF by
connecting a general-purpose interface.
The weekly schedule of up to ten patterns (no setting + nine
patterns) is available for setting.
"ON/OFF", "Operation Prohibit", "COOL/HEAT" and "Set
Temperature" can be scheduled with up to 16 settings in one
pattern.
It can be connected to the center control transmission line or to
the indoor/outdoor transmission line without the power supply
unit (PAC-SC50KUA). It is nonpolar 2-wire.
It can be interlocked with a building management system using
the external input/output managing function.
An error unit address and error code appear on the display.
(*) Use in combination with other system controllers.
System example
System
remote
controller
Power supply
unit
ME R/C
LOSSNAY
Schedule timer
MA R/C
Simple
ME R/C
R/C:Remote Controller
69

Building Air conditioning
control system
CENTRALIZED
REMOTE CONTROLLER
ON/OFF remote controller PAC-YT40ANRA
16 groups/50 units can be controlled
Up to 16 groups/50 units can be operated with one ON/OFF remote controller.
A general-purpose interface is available for control, so general devices can also be
turned ON and OFF.
Just press a switch to start.
All of the units can be started and stopped by pressing the main switch, and each
unit in the group can be started and stopped with individual switches.
A general-purpose interface is available for control, so general devices can also be
turned ON and OFF.
LED flashing during failure.
If any error should occur in the air conditioner, its details can be confirmed easily
with the flashing LED. The LED also indicates whether each group is running or
stopped.
Interlock operation with external system possible.
It can be flexibly interlocked with a card reader, fire alarm system or building
management system, etc., using the incorporated external input/output function.
Flexible group setting.
The groups can be easily configured, so the group pattern can be freely set
according to the layout.
The ON/OFF remote controller can be connected at the indoor/outdoor
transmission line without the power supply unit.
System example
LOSSNAY
ON/OFF
remote
controller
PAR-F27MEA
PZ-52SF
PAR-21MAA
R/C:Remote Controller
PAC-YT51CRA
70

UP
POWER SUPPLY UNIT
MODEL PAC-SC50KUA
POWER RATING
WEIGHT
2.11kg
SERIAL No.
MITSUBISHI ELECTRIC CORPORATION
Building Air conditioning
control system
CENTRALIZED
REMOTE CONTROLLER
Integrated centralized control software TG-2000A
(1) Example of Basic System Configuration.
Charge
license
Web
monitor
license
Input
G-50A
12VDC
M-NET
Single-phase 208/230V
Single-phase 208/230V
Schedule
license
Uninterruptive
power supply (UPS)
Power supply unit
PAC-SC50KUA
3-phase 208/230V
(3-wire)
RS-232C
RS-485
Indoor unit system
watt-hour meter
Outdoor unit system
watt-hour meter
Converter
Central controller
personal computer
TG-2000A
Indoor unit
watt-hour meter
Compatible with TG-2000A Ver. 4.10 and higher
* The electric amount count software or separately
procured parts must be used with the designated PLC.
Uninterruptible
power supply (UPS)
power source
Indoor unit system
watt-hour meter
Indoor unit
watt-hour meter
Outdoor unit system
watt-hour meter
PLC (with electric amount count
software)
Central control
personal computer
TG-2000A
Integrated
centralized control
software installation
Integrated centralized control
software installation
71
Main features of TG-2000A
The TG-2000A can realize the following functions using
the G-50A/GB-50A option (license).
* Operation/monitor
* Annual/weekly schedule
* Charge
* Energy saving *1
* Peak cut *1
*1: Compatible with TG-2000A Ver. 4.10 and higher,
G-50A Ver. 2.51 or later.
1 Up to 2000 indoor units (40 G-50A/GB-50A units) can be operated and monitored simultaneously.
2 The air-conditioner layout can be displayed on the screen, making control and operation easier.
3 The annual and weekly schedules can be set. Two schedules, such as the summer master and winter master, can be
saved in the weekly schedule.
4 Air-conditioning charges can be calculated based on the multiple air-conditioner usage results. The power apportionment
percentage data and apportioned power rate can be calculated for each indoor unit using the power apportionment
function, and can be output as a CSV format file. * Power apportionment charging is not possible with the old model, A control or K control.
Charging without WHM : The user manually inputs the power rate to calculate the air-conditioning charges. (Using a tool)
RS-485 WHM charging : The RS-485 WHM value is automatically tabulated to calculate the air-conditioning charges.
PLC + pulse WHM charging : The pulse output WHM value is automatically tabulated by the PLC to calculate the air-conditioning charges.
5 Energy saving operation is possible using the "ON/OFF", "set temperature change", "fan operation changeover" and
"performance save operation (60% to 90%)" functions.
Energy saving operation matching the amount of power in use is possible by using the PLC's electric amount count software.
6 Night set-back operation is possible with schedule settings. *1*4
7 General equipment can be operated and monitored. *2
8 General equipment can be schedule-controlled when using PAC-YG21CDA with PLC.
For details of PLC refer to Installation Manual of PAC-YG21CDA. *3
*1: Compatible with TG-2000A Ver. 4.10 and higher, G-50A Ver. 2.51 and higher.
*2: Compatible with TG-2000A Ver. 4.30 and higher, G-50A Ver. 2.51 and higher.
*3: Compatible with TG-2000A Ver. 4.60 and higher, G-50A Ver. 2.70 and higher.
*4: With Night Set-Back function,the CITY MULTI system can run at heating mode with target temperature set to 54 F/12 C
under schedule control. This function can protect the room from dropping down to extremely low temperature at mid-night.

Building Air conditioning
control system
CENTRALIZED
REMOTE CONTROLLER
LONWORKS (LMAP02)
CITY MULTI TM can easily combine into a Building Management System (BMS) via the LonWorks TM and M-NET adapter
LMAP03-U. LonWorks TM is an opened transmission protocol widely used at BMS, and related equipment control.
CITY MULTI TM is therefore compatible with large-scaled BMS management via LonWorks TM .
One LM ADAPTER unit can connect up to 50 Groups/50 indoor units.
Using a single LONWORKS adapter (LM ADAPTER), you can connect up to
a maximum of 50 indoor units.
Operation
Monitor
Item
Request On/Off
Request Mode
Setpoint from network (Both cool and heat)
Request Fanspeed
Request Local Prohibit On/Off
Request Local Prohibit mode
Request Local Prohibit SetPoint
Request All Off
On/Off run state
Mode state
Setpoint state (both cool and heat)
FanSpeed state
Thermo On/Off state
Temperature state of indoor
Alarm state
Local Prohibit On/Off state
Local Prohibit mode state
Local Prohibit SetPoint state
LMAP
LMAP 02
Protocol converter
between LON WORKS
and M-NET
LON WORKS
LMAP
M-NET
CITY MULTI System
Example of System Configuration
System design made simple through integration of
various devices into a total control configuration.
208-230V
60Hz
Outdoor unit
CITY MULTI
Outdoor unit
LON WORKS
(78kdps)
LMAP
M-NET
Indoor units
Max. 50 indoor units
Indoor units
Indoor units
Indoor units
Indoor units
Center
control device
Lighting
Security
Remote
controller
Remote
controller
Remote
controller
Remote
controller
Remote
controller
LON WORKS
The building management system is connected to the CITY MULTI air conditioning system using LON WORKS , which is widely used on
field networks, allowing for an open network and savings in construction to face.
LON, LON WORKS and the Echelon logo are trademarks of
Echelon Corporation registered in the United States and other countries.
72

UP
Building Air conditioning
control system
CENTRALIZED
REMOTE CONTROLLER
BACnet TM interface(PAC-YG31CDA)
MITSUBISHI ELECTRIC's CITYMULTI can be easily connect to the building management system through BACnet. BACnet is the
appropriate transmission method and used in many of the backbone networks and also it is easy to combine with other equipment
corresponding to BACnet.
One BACnet interface software manages up to 500 Groups/500 Indoor units. (10 G-50A/GB-50A units).
(1) Example of Basic System Configuration.
Central
monitor
BMS
TM
BACnet
LAN
G-50A
M-NET
WHM
WHM
TM
BACnet interface software
PAC-YG31CDA
M-NET
PAC-SC50KUA
Power supply unit
G-50A
Web
Browser
(Optional)
TG-2000A
(Optional)
73
Operation
Monitor
Item
On/Off (state)
Operation mode (state)
Fan Speed (state)
Air direction (state)
Room Temp.
Filter Signal
Alam signal
Error Code
Communication State
On/Off (setup)
Operation mode (setup)
Fan Speed (setup)
Air direction (setup)
Set Temp.
Filter Signal
Prohibition of local operation (On/Off)
Prohibition of local operation (Mode)
Prohibition of local operation (filter reset)
Prohibition of local operation (Set temp.)
System Forced Off

CITY MULTI
OPTIONAL PARTS
R410A
OPTIONAL PARTS FOR OUTDOOR UNITS
For PU(H)Y, PURY series
Description
High static pressure motor
Model
PAC-KBU04MT-F
Remarks
~ 60Pa
Note: In case of using PAC-KBU04MT-F, when carrying out intensive install of the outdoor unit, please extend on installation interval to 20mm or more.
For PU(H)Y, PURY series
Description Model Total capacity of indoor unit
Branch pipe (Joint)
Branch pipe (Header)
CMY-Y102S-G
CMY-Y102L-G1
CMY-Y202-G1
CMY-Y302-G1
CMY-Y104-G
CMY-Y108-G
CMY-Y1010-G
Note : Indoor unit capacities
The capacity of an indoor unit is the same as the number used for its type identification.
200 or below
201-400
401-650
The 1st branch of P450~P650
651 or above
The 1st branch of P700~P1250
For 4 branches
For 8 branches
For 10 branches
For PUMY-P100, P125, P140YHM / PUMY-P100, P125, P140VHM
Description
Branch Pipe (2 Branch)
Header
Header
Drain Socket
Centralized Drain Pan
Port Connector (ø9.52 → ø12.7 )
Port Connector (ø15.88 → ø19.05)
Air Protect Guide ( 2 pcs required )
Model
CMY-Y62-G-E
CMY-Y64-G-E
CMY-Y68-G-E
PAC-SG61DS-E
PAC-SG64DP-E
PAC-SG73RJ-E
PAC-SG75RJ-E
PAC-SH63AG-E
OPTIONAL EQUIPMENT FOR BC CONTROLLER
BC Controller Model Junction pipe kit Branch pipe
CMB-P104V-G, GB
CMB-P105V-G
CMB-P106V-G
CMB-P108V-G, GA, GB
CMB-P1010V-G, GA
CMB-P1013V-G, GA
CMB-P1016V-G, GA
CMY-R160-J
CMY-Y102S-G
74

CITY MULTI
OPTIONAL PARTS
R410A
OPTIONAL PARTS FOR INDOOR UNITS
Description
Decoration panel
Multi-function casement
High-efficiency filter element
Air outlet shutter plate (1 set)
4-way cassette type (PLFY-VCM / VAM)
Model
SLP-2AA
PLP-6AA
PAC-SG03TM-E
PAC-SG01KF
PAC-SG06SP-E
Applicable capacity
VAM
–
P32, P40, P50, P63, P80, P100, P125
P32, P40, P50, P63, P80, P100, P125
P80, P100, P125
P32, P40, P50, P63, P80, P100, P125
VCM
P20, P25, P32, P40
–
–
–
–
Description
Decoration panel
OA duct flange
2-way cassette type (PLFY-VLMD)
Model
CMP-40VLW-B
CMP-63VLW-B
CMP-100VLW-B
CMP-125VLW-B
PAC-KH11OF
Applicable capacity
PLFY-VLMD-B
P20, P25, P32, P40
P50, P63
P80, P100
P125
P20, P25, P32, P40, P50, P63, P80, P100
1-way cassette type(PMFY-VBM)
Description
Model
Applicable capacity
Decoration panel PMP-40BM P20, P25, P32, P40
Description
Drain lift-up mechanism
Long life filter
Filter box
Ceiling concealed type (PEFY-VMH)
Model
PAC-KE04DM-F
PAC-KE32LAF-F
PAC-KE86LAF
PAC-KE88LAF
PAC-KE89LAF
PAC-KE85LAF
PAC-KE63TB-F
PAC-KE80TB-F
PAC-KE140TB-F
PAC-KE250TB-F
Applicable capacity
PEFY-VMH
P40~P250
–
P40, P50, P63
P71, P80
P100, P125, P140
P200, P250
P40, P50, P63
P71, P80
P100, P125, P140
P200, P250
Ceiling concealed type (PEFY-VMM)
Remarks
Standard Filter is attached
Necessary when long life filter is used
Description
Round shape duct flange
Drain lift-up mechanism
Model
PAC-KE32EDF-F
PAC-KE50EDF-F
PAC-KE80EDF-F
PAC-KE125EDF-F
PAC-KE140EDF-F
PAC-KE03DM-F
Applicable capacity
P20, P25, P32
P40, V50
P63, P71, P80
P100, P125
P140
P20, P25, P32, P40, P50, P63, P71, P80, P100, P125, P140
Description
High efficiency filter
Drain lift-up mechanism
Ceiling suspended type (PCFY-VGM)
Model
PAC-SE80KF-E
PAC-SE81KF-E
PAC-SE82KF-E
PAC-SE84DM-E
PAC-SE85DM-E
PAC-SE86DM-E
Applicable capacity
P40
P63, P100
P125
P40
P63
P100, P125
Description
Long life filter
Filter box
Drain water lift-up kit
Fresh air intake type (PEFY-VMH-E-F)
Model
PAC-KE88LAF
PAC-KE89LAF
PAC-KE85LAF
PAC-KE80TB-F
PAC-KE140TB-F
PAC-KE250TB-F
PAC-KE04DM-F
Applicable capacity
P80
P140
P200, P250
P80
P140
P200/P250
P80, P140, P200, P250
75

Single phase Multi Split system (5HP)
MSZ-FA series
MSZ-GA series
Branch Box
MSZ-FA series
SLZ series
MFZ series
PLA series
PEAD series
SEZ series
MXZ-8A140VA Single phase, 50Hz
*MXZ-8A140VA can NOT be connected with City Multi indoor units.
Up to 8 indoor units
can be connected !
The Air Conditioning & Refrigeration Systems Works acquired ISO 9001 certification under Series
9000 of the International Standard Organization (ISO) based on a review of Quality , management for
the production of refrigeration and air conditioning equipment.
FM 33568 / ISO 9001;2000
ISO Authorization System
The ISO 9000 series is a plant authorization system relating to quality management as stipulated by
the ISO. ISO 9001 certifies quality management based on the "design, development, production,
installation and auxiliary services" for products built at an authorized plant.
The Air Conditioning & Refrigeration Systems Works acquired environmental management system
standard ISO 14001 certification.
The ISO 14000 series is a set of standards applying to environmental protection set by the
International Standard Organization (ISO).
Certificate Number EC97J1227
http://Global.MitsubishiElectric.com/
MITSUBISHI ELECTRIC PRODUCTS ARE DISTRIBUTED BY...
HEAD OFFICE: MITSUBISHI DENKI BLDG., 2-2-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
http://Global.MitsubishiElectric.com
MEE05K437
New publication effective Jul. 2006
Specifications subject to change without notice