510 OEM Relative pressure transmitter

510
OEM Relative pressure transmitter
0 … 2.5 – 600 bar

Technical overview
These compact OEM pressure transmitters
type 510 have been developed for
applications in the industrial refrigeration
technology.
The special sensor is based on thick-film
technology, developed by Huba Control,
which utilises a special grade of steel welded
to the pressure sensor. This means that
the 510 can be used for all gases and media
in refrigeration, including ammonia. Highest
requirements concerning EMC and accuracy
for all temperature ranges can be met in
combination with the unique integrated
electronic design.
Suitable from small series to high quantity
applications with best price to performance
ratio.
The distinct advantages
• Compact, rugged construction for
highest operational reliability
• Protection IP 67
• Welded without sealing parts, no
elastomer seals
• Negligible temperature influence on
accuracy
• Excellent EMC-capacity
• Saving time by quick cable mounting by
the customer with Quickon-System
5
Legend to cross-section drawing
1 Pressure connection
2 Steel cell welded
3 Measuring cell
4 Electronic with EMC-protection
5 Electrical connection
(example Quickon)
4
3
2
1
Medium
Liquids, refrigerants (incl. ammonia) and
neutral gases
Pressure range
Relative
0 … 2.5 – 600 bar
Tolerable overload
5.0 x Measuring range (fs) at -1 … 5 bar
3.0 x Measuring range (fs) > 6 … 600 bar
Rupture pressure
10 x Measuring range (fs) at -1 … 5 bar
6.0 x Measuring range (fs) > 6 … 600 bar
Materials in contact with the medium
Pressure connections:
Stainless steel 1.4305 / AISI 303
Measuring cell:
Stainless steel 1.4016 / AISI 430
Case material
Stainless steel 1.4305 / AISI 303
Temperature
Medium -40 … +150 ºC
Ambiance -40 … +85 ºC
Storage -40 … +85 ºC
Output
Power supply
3-wire
0 … 5 VDC 8 … 33 VDC
1 … 6 VDC 8 … 33 VDC
0 … 10 VDC 12.3 … 33 VDC
0.5 … 4.5 V ratiom. 5 VDC (4.75 ... 5.25)
2-wire
4 … 20 mA 8 … 33 VDC
Electric strength
Load
3-wire
2-wire
<
500 VDC
> 10 kOhm /

Versions
A B C D
A – Inside thread 7/16-20 UNF
B – Outside thread G1/4
C – Connector M12x1
D – Quickon cable screwing
Accuracy
Parameter
Unit
Tolerance zero point max. % fs ± 0.5
Tolerance full scale max. % fs ± 0.5
Resolution % fs 0.3
Total of linearity,
hysteresis and repeatability max. % fs ± 0.5
Long terme stability acc. to DIN EN 60770 % fs ± 1.0
TC zero point 1) max. % fs/10K ± 0.3
TC sensitivity 1) max. % fs/10K ± 0.15
Test conditions:
25 ºC, 45% rF, Power supply 24 VDC
TC0 / TCE -40 … +125 ºC
Order code selection table in bar 510. 9 X X X X X X X X X
Pressure range 2) 0 ... + 2.5 bar 1 4
0 ... + 4 bar 1 5
0 ... + 6 bar 1 7
0 ... + 7 bar 2 9
0 ... + 10 bar 3 0
0 ... + 16 bar 3 1
0 ... + 25 bar 3 2
0 ... + 40 bar 3 3
0 ... + 60 bar 4 0
0 ... + 100 bar 4 1
0 ... + 160 bar 4 2
0 ... + 250 bar 4 3
0 ... + 400 bar (over pressure protection < 1200 bar) 5 4
0 ... + 600 bar (over pressure protection < 1500 bar) 5 5
▲ Fullscale signal at these pressures
Sealing material None (cell welded) S
Adjustment Factory 0
Output and power supply 0 … 5 V 8 … 33 VDC 3-wire 1
1 … 6 V 8 … 33 VDC 3-wire 6
0 … 10 V 12.3 … 33 VDC 3-wire 2
0 … 10 V 24 VAC ±15% / 16 … 34 VDC 3-wire (only quickon & cable) 7
4 … 20 mA 8 … 33 VDC 2-wire 3
0.5 … 4.5 V ratiom. 5 VDC (4.75 ... 5.25) 3-wire 4
Electrical connection Cable 1.5 m IP 67 0
Quickon including cable screwing, without cable IP 67 1
Connector M12x1 plastic thread 3) IP 67 5
Connector DIN 175301-803-C 3) mini DIN plug connection (Fig. 1) IP 65 8
Connector DIN 175301-803-C 3) mini DIN plug connection (Fig. 2) IP 65 9
Pressure connection 4) Inside thread 7/16-20 UNF Schrader 0
Inside thread G1/4 (O-ring in FPM) 1
Outside thread 7/16-20 UNF 2
Outside thread 1/4-18 NPT 3
Outside thread R1/4 acc. DIN 2999 4
Outside thread G1/4 sealed at back DIN 3852 form E (Profile seal ring in FPM) 5
Version Stainless steel 1.4305 / AISI 303 0
Pressure range variation Indicate W and state range on order (e.g.: W0…12bar/Out1…10V) W
Accessories
Order number
Quickon cable screwing 107359
Female connector DIN 175301-803-C (mini DIN) 104244
Female connector for connector M12x1 106975
Calibration certificate 104551
1)
TC = Temperature coefficient
2)
Adjustment in psi (min. 100 psi fs) and other pressure ranges and materials on request
3)
Delivery without female connector
4)
Other pressure connections on request
510 / EDITION 01/2010, Technical data subject to change.
3

Order code selection table in psi 510. 9 X X X X X X X X X
Pressure range 2) 0 ... + 30 psi B 4
0 ... + 60 psi B 5
0 ... + 100 psi B 6
0 ... + 200 psi C 1
0 ... + 300 psi C 2
0 ... + 500 psi C 3
0 ... + 750 psi D 0
0 ... + 1000 psi D 1
0 ... + 2000 psi D 2
0 ... + 3000 psi D 3
0 ... + 5000 psi (over pressure protection < 15000 psi) E 4
0 ... + 7500 psi (over pressure protection < 19000 psi) E 5
▲ Fullscale signal at these pressures
Sealing material None (cell welded) S
Adjustment Factory 0
Output and power supply 0 … 5 V 8 … 33 VDC 3-wire 1
1 … 6 V 8 … 33 VDC 3-wire 6
0 … 10 V 12.3 … 33 VDC 3-wire 2
0 … 10 V 24 VAC ±15% / 16 … 34 VDC 3-wire (only quickon & cable) 7
4 … 20 mA 8 … 33 VDC 2-wire 3
0.5 … 4.5 V ratiom. 5 VDC (4.75 ... 5.25) 3-wire 4
Electrical connection Cable 1.5 m IP 67 0
Quickon including cable screwing, without cable IP 67 1
Connector M12x1 plastic thread 3) IP 67 5
Connector DIN 175301-803-C 3) mini DIN plug connection (Fig. 1) IP 65 8
Connector DIN 175301-803-C 3) mini DIN plug connection (Fig. 2) IP 65 9
Pressure connection 4) Inside thread 7/16-20 UNF Schrader 0
Inside thread G1/4 (O-ring in FPM) 1
Outside thread 7/16-20 UNF 2
Outside thread 1/4-18 NPT 3
Outside thread R1/4 acc. DIN 2999 4
Outside thread G1/4 sealed at back DIN 3852 form E (Profile seal ring in FPM) 5
Version Stainless steel 1.4305 / AISI 303 0
Pressure range variation Indicate W and state range on order (e.g.: W0…800psi/Out1…10V) W
Order code selection table in MPa 510. 9 X X X X X X X X X
Pressure range 2) 0 ... + 0.25 MPa G 4
0 ... + 0.4 MPa G 5
0 ... + 0.6 MPa G 6
0 ... + 0.7 MPa G 7
0 ... + 1 MPa H 0
0 ... + 1.6 MPa H 1
0 ... + 2.5 MPa H 2
0 ... + 4 MPa H 3
0 ... + 6 MPa K 0
0 ... + 10 MPa K 1
0 ... + 16 MPa K 2
0 ... + 25 MPa K 3
0 ... + 40 MPa (over pressure protection < 120 MPa) L 4
0 ... + 60 MPa (over pressure protection < 150 MPa) L 5
▲ Fullscale signal at these pressures
Sealing material None (cell welded) S
Adjustment Factory 0
Output and power supply 0 … 5 V 8 … 33 VDC 3-wire 1
1 … 6 V 8 … 33 VDC 3-wire 6
0 … 10 V 12.3 … 33 VDC 3-wire 2
0 … 10 V 24 VAC ±15% / 16 … 34 VDC 3-wire (only quickon & cable) 7
4 … 20 mA 8 … 33 VDC 2-wire 3
0.5 … 4.5 V ratiom. 5 VDC (4.75 ... 5.25) 3-wire 4
Electrical connection Cable 1.5 m IP 67 0
Quickon including cable screwing, without cable IP 67 1
Connector M12x1 plastic thread 3) IP 67 5
Connector DIN 175301-803-C 3) mini DIN plug connection (Fig. 1) IP 65 8
Connector DIN 175301-803-C 3) mini DIN plug connection (Fig. 2) IP 65 9
Pressure connection 4) Inside thread 7/16-20 UNF Schrader 0
Inside thread G1/4 (O-ring in FPM) 1
Outside thread 7/16-20 UNF 2
Outside thread 1/4-18 NPT 3
Outside thread R1/4 acc. DIN 2999 4
Outside thread G1/4 sealed at back DIN 3852 form E (Profile seal ring in FPM) 5
Version Stainless steel 1.4305 / AISI 303 0
Pressure range variation Indicate W and state range on order (e.g.: W0…1.2MPa/Out1…10V) W
4
510 / EDITION 01/2010, Technical data subject to change.

Dimensions in mm
Electrical connections
7/16-20 UNF
21
7/16-20 UNF
Inside thread
with Schrader 21
22.8
brown
IN
2-wire
GND
brown
IN
3-wire
Cable screwing or cable Quickon
white
GND
Quickon
13.5 8.35
8.35
38.5
64.6
74 (mounted)
OUT green
OUT green
21
1/4-18 NPT
21
Fig. 1
Connector DIN 175301-803-C (mini DIN)
GND OUT
R1/4
22.8
OUT
2 2 3 3
1
1
GND
13
8.35
12.7
8.35
39.5
G1/4
21
G1/4
Inside thread
21
60.5
22.8
87 (mounted)
M12x1
Fig. 2
Connector DIN 175301-803-C (mini DIN)
OUT
M12x1
GND
2 2 3 3 OUT
1
1
IN
GND IN
GND
12 8.35
2.1
19 38.4
67.4
102 (mounted)
IN
1 4
GND
IN
3 3
OUT
1
4
GND
OUT
Electromagnetic compatibility
CE conformity according EN 61326-2-3.
510 / EDITION 01/2010, Sous réserve de modifications techniques.
5

Headquarters
Huba Control AG Schweiz
Industriestrasse 17
CH-5436 Würenlos
Telefon ++41 (0) 56 436 82 00
Telefax ++41 (0) 56 436 82 82
info.ch@hubacontrol.com
Huba Control AG
Niederlassung Deutschland
Schlattgrabenstrasse 24
72141 Walddorfhäslach
Telefon ++49 (0) 7127 23 93-00
Telefax ++49 (0) 7127 23 93-20
info.de@hubacontrol.com
Huba Control SA
Succursale France
Technopôle Forbach-Sud
57602 Forbach Cedex
Téléphone ++33 (0) 387 847 300
Télécopieur ++33 (0) 387 847 301
info.fr@hubacontrol.com
Huba Control AG
Vestiging Nederland
Hamseweg 20A
3828 AD Hoogland
Telefoon ++31 (0) 33 433 03 66
Telefax ++31 (0) 33 433 03 77
info.nl@hubacontrol.com
Huba Control AG
Branch Office United Kingdom
Unit 3 Network Point, Range Road
Witney Oxfordshire OX29 0YD
Phone ++44 (0) 1993 776 667
Fax ++44 (0) 1993 776 671
info.uk@hubacontrol.com
Huba Control AG
Rep. Office Singapore
Rep Office Singapore, No. 16 Ayer Rajah Crescent Witney
#06-06B Tempco Technominium, SG-139965 Singapore
Phone ++65 (0) 61 004 822
Fax ++44 (0) 63 994 822
info.sg@hubacontrol.com
Huba Control AG
Rep. Office China
Rep Office Shanghai, CBC Building
49A Wuyi Road, CN-Shanghai 200050
Phone ++86 (0) 21 511 808 21
Fax ++86 (0) 21 515 520 99
info.cn@hubacontrol.com
Technische Änderungen vorbehalten.
Technical data subject to change.
Sous réserve de modifications techniques.
510.Edition01/2010
www.hubacontrol.com