a PDF summary of All - Goodfellow

More documents

Recommendations

Info

Sphere Small balls which are precision ground. Tolerances Diameter: +5% Sputtering Target A high purity material used as a source for sputtering, a cold vaporization process in which atoms are physically removed from the target surface by ion bombardment. Tolerances Thickness: +0.5mm Size: +0.5mm 5 # Goodfellow Corporation 125 Hookstown Grade Road, Coraopolis, PA 15108-9302. USA Tel: 1-800-821-2870 : Fax 1-800-283-2020 Product Descriptions Tube A hollow length of material normally circular in section. Most tubes are straight except those made of flexible polymer. Tolerances Outside diameter: 42mm +0.05mm Polymer +10% Ceramic +10% 45mm +0.1mm Polymer +10% Ceramic +10% >5mm +5% Polymer +10% Ceramic +10% Wall thickness: +10% Polymer +20% Ceramic +20% Length:
Email: info@goodfellowusa.com Tel +1 724 695 7060 : Fax +1 724 695 7063 Analyses Purity Purities listed are quoted with respect to total metallic impurities. Typical analyses may give additional information about likely non-metallic impurities. High Purity For materials described as High Purity, the actual analysis of metallic impurities will be supplied free of charge. For other items, an actual analysis can be supplied and a charge will be made for the analysis and for the sample used. Supports Some items from our range of foils need to be supported on one side of the foil to enable both you and us to handle these very delicate materials. Two types of support can be used, the choice being governed by the material. Wherever possible we use a temporary support, a permanent support only being used when the material is brittle (for example Chromium or Manganese). The temporary support is Acrylic, approximately 0.2mm thick. This may be removed by dissolving in 2-Propanone (Acetone). Our permanent support is Polyester, thickness 0.125mm, which is hot-press laminated to one face of the foil. It cannot be removed without destroying the foil. November 2012 General Information Light Tight (LT) & Not Light Tested (NLT) Light tight (LT) foils are supplied without visible pinholes whereas non-light tested (NLT) foils will normally contain pinholes but may occasionally be free from pinholes. Foils 0.025mm or more in thickness are supplied LT unless otherwise stated. Foils less than 0.025mm are normally supplied NLT, however, if you require LT foils, please ask. An additional charge may be made if we are able to supply LT foils. Vacuum tight Vacuum tight foils show no detectable leakage when tested with a helium mass spectrometer with a sensitivity of 10 -9 atm-cm 3 .s -1 . Technical Data and Information All information and technical data are given as a guide only. Although every effort has been made to ensure that the information is correct, no warranty is given as to its completeness or accuracy. Tolerances For details of our standard tolerances, please refer to the Product Description section. In many cases, closer tolerances are available but may be subject to an extra charge. If you have any special requirements it is important that you tell us at the time of ordering. This includes special tolerances, dimensional uniformity or any other special requirement which you may have (for example edge finish, packaging, labelling etc.). Check out www.goodfellowusa.com or email info@goodfellowusa.com for latest prices 6 # Goodfellow Corporation
Page 1 and 2: Serving The Needs of Science and In
Page 3 and 4: Email: info@goodfellowusa.com Tel +
Page 7: Email: info@goodfellowusa.com Tel +
Page 59 and 60:
Email: info@goodfellowusa.com Tel +
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207:
show all

a PDF summary of All - Goodfellow

Create successful ePaper yourself

Delete template?

Save as template?