Smith's heat emiters - Artizan Heating

Independent tests* show that fan convectors are at least 24% more energy efficient than a panel radiator in heating up a room.
*Tests carried out by BSRIA (Building Services Research and Information Association) in August 2008
Heat Output ∆t 60ºC Heat Output ∆t 50ºC
Normal Boost Normal Boost Fan- Flow & Return
Model kW (Btu/h) kW (Btu/h) kW (Btu/h) kW (Btu/h) Casing Colour 0nly Connections
Hydronic CT18 3.5 (11900) 5.5 (18800) 2.8 (9600) 4.4 (15000) White • 22mm
Electric E 4kW 4.0 n/a 4.0 n/a White • n/a
∆t 60ºC assumes a mean water temperature of 80ºC and room temperature of 20ºC. ∆t 50ºC assumes a mean water temperature of 70ºC and room temperature of
20ºC. Hydronic outputs tested in accordance with BS 4856. Fan-only option operational only when central heating system is switched off.
Power Consumption
Water
Main Flexible Isolating Fused Normal Boost Capacity
Model Cable Transformer Hoses Valves Spur Watts Watts (Litres)
Hydronic CT18 1.5m n/a n/a n/a 3A 50 70 0.9
Electric E 4kW 1.5m n/a n/a n/a 20A 4045 n/a n/a
Skyline CT18
Finish
Outer casing 0.7mm zinc-coated steel.
Polyester powder-coated.
Paint specification: textured white
BS 4800 00A01 18% gloss.
Installation
• Maximum installation height 3.2m
(10'6") to underside
• Installed to 180mm - penetration
depth in recess (excluding fittings)
• Four air inlet options: room only, void
only, room and void, fresh air (spigot
required)
• 600mm side clearance required
• Fixing brackets (4) supplied for
connection to 6mm threaded rods or
chains (rods and chains - not
supplied)
• Blanking plates (2) supplied for air
circulation options
• Unit must be earthed
• Supplied with remote operating
switch
• Suitable for two-pipe central heating
systems only
Commissioning
Check water temperature is hot enough
to activate low temperature cut-out
(LTC). The inclusion of an automatic
air vent at the highest point is
recommended to avoid possible
air locks.
Controls
Two rocker fan switches -
normal/off/boost, fan-heating/fan-only.
Low temperature cut-out thermostat set
to energise fan at approx. 42ºC (108ºF).
Accessories
Wall-mounted room thermostat with
on/off switch. Fresh air inlet spigot to
suit 100mm flexible hose.
90
Skyline CT18
Pipe Centres
22
28
22mm
Flow and Return Pipes
Outlet panel fits over
ceiling tile frame
Air in void or room
damper at both ends
45
centres
280
248
centres
600
542
516
centres
All dimensions in mm
Skyline E 4kW
Heat exchanger
drain off valve
Fixing points
507
600
498
centres
15
264
151
90
100
555
600
600
Skyline E 4kW
Finish
Outer casing 0.9mm zinc-coated steel.
Polyester powder-coated.
Paint specification: textured white
BS 4800 00A01 18% gloss.
Installation
• Maximum installation height 3.2m
(10'6") to underside
• Minimum 150mm void space required
for recessed installation
• Not suitable for bathrooms and other
high humidity areas
• Two air inlet options: room only,
room and void
• Maximum flexibility in installation:
only 600mm - side clearance required
• Facility for connection to 6mm
threaded rod or chains (rods and
chains - not supplied)
• 20 amp fused spur required
• Unit must be earthed
• Supplied with remote operating
switch
Controls
Rocker switches for fan and element.
Overheat protection: thermal cut-out.
Manual reset procedure: switch power
off at mains, wait 5 minutes, switch
power on.
Room thermostats used in conjunction
with this product must be rated at
16A minimum.
Accessories
Surface mounting kit - 135mm. Provides
a complete four-sided trim when fitted
to a solid ceiling.
Ceiling tile spacer - 85mm. Provides
semi-recessed profile to match Skyline
CT18 when used in ceiling tile frame.
Multiple positions (14) for suspension points
33