ABLEBOND® 84-1LMISR4
ABLEBOND® 84-1LMISR4
ABLEBOND® 84-1LMISR4
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
ABLEBOND <strong>84</strong>-<strong>1LMISR4</strong><br />
ABLEBOND ® <strong>84</strong>-<strong>1LMISR4</strong><br />
ELECTRICALLY CONDUCTIVE DIE ATTACH ADHESIVE<br />
导 电 粘 晶 胶<br />
DESCRIPTION<br />
Ablebond ® <strong>84</strong>-<strong>1LMISR4</strong> electrically<br />
conductive die attach adhesive has<br />
been formulated for use in high<br />
throughput, automatic die attach<br />
equipment. The rheology of Ablebond<br />
<strong>84</strong>-<strong>1LMISR4</strong> adhesive allows<br />
minimum adhesive dispense and die<br />
put down dwell times, without tailing<br />
or stringing problems. The unique<br />
combination of adhesive properties<br />
makes Ablebond <strong>84</strong>-<strong>1LMISR4</strong><br />
adhesive one of the most widely used<br />
die attach materials in the<br />
semiconductor industry.<br />
FEATURES<br />
• Excellent dispensability with<br />
minimal tailing and stringing<br />
• Box oven cure<br />
产 品 概 述<br />
Ablebond ® <strong>84</strong>-<strong>1LMISR4</strong> 导 电 粘 晶 胶<br />
非 常 适 用 在 高 产 率 、 自 动 粘 晶 设 备<br />
上 。Ablebond ® <strong>84</strong>-<strong>1LMISR4</strong> 导 电 粘<br />
晶 胶 的 流 变 特 性 使 得 它 可 以 进 行 最<br />
小 剂 量 的 点 胶 , 以 及 最 小 的 粘 晶 停<br />
留 时 间 , 并 且 没 有 拖 尾 或 拉 丝 问<br />
题 。 因 此 ,Ablebond ® <strong>84</strong>-<strong>1LMISR4</strong><br />
独 特 的 粘 接 性 能 使 得 它 成 为 半 导 体<br />
工 业 中 最 为 常 用 的 粘 晶 材 料 之 一 。<br />
特 性<br />
• 优 良 的 点 胶 性 能 , 具 有 最 小 的 拖<br />
尾 或 拉 丝 现 象<br />
• 箱 式 烘 箱 中 固 化<br />
UNCURED PROPERTIES<br />
固 化 前 的 性 质<br />
TEST DESCRIPTION<br />
测 试 方 法 描 述<br />
TEST METHOD<br />
测 试 方 法<br />
Filler Type/ 填 料 类 型<br />
Silver<br />
Viscosity/ 粘 度 @ 8,000 cps Brookfield CP51 @ 5rpm ATM-0018<br />
Thixotropic Index/ 触 变 指 数 5.6 Visc @ 0.5/Visc @ 5rpm ATM-0089<br />
Work Life/ 工 作 时 间 @25℃ 18 hours Physical work life by % filler ATM-0067<br />
Storage Life @-40℃ 1 year ATM-0068<br />
CURE PROCESS DATA<br />
固 化 条 件<br />
TEST DESCRIPTION<br />
测 试 方 法 描 述<br />
TEST METHOD<br />
测 试 方 法<br />
Recommended Cure Condition/ 推 荐 固 化 条 件 1 hour @ 175℃<br />
Alternate Cure Condtion (1) / 可 选 固 化 条 件 3-5℃/min ramp to 175℃+1 hour @ 175℃<br />
1 The ramp cure was oberserved to yield reduced voiding and increased strength.<br />
渐 进 升 温 可 以 减 少 气 泡 产 生 , 以 及 增 加 强 度 。<br />
Weight loss on cure / 固 化 后 的 热 失 重 5.3% 10×10 mm Si die on glass slide ATM-0031<br />
PHYSIOCHEMICAL PROPERTIES-PSOT CURE<br />
固 化 后 的 物 理 化 学 性 质<br />
Ionics/ 离 子 Chloride<br />
5 ppm<br />
Sodium<br />
3 ppm<br />
Potassium<br />
1ppm<br />
TEST DESCRIPTION<br />
测 试 方 法 描 述<br />
Teflon flask 5 gm sample/20-40 mesh 50<br />
gm DI water 100℃ for 24 hours<br />
TEST METHOD<br />
测 试 方 法<br />
ATM-0007<br />
Water Extract Conductivity<br />
导 电 率<br />
13 μmhos/cm ATM-0044<br />
pH/ 酸 碱 度 6 ATM-0002<br />
Weight Loss/ 热 失 重 @300℃ 0.35%<br />
Thermogravimetric Analysis<br />
热 解 重 量 分 析 法<br />
ATM-0073<br />
09/03 - 1 -
ABLEBOND <strong>84</strong>-<strong>1LMISR4</strong><br />
PHYSIOCHEMICAL PROPERTIES-PSOT CURE<br />
固 化 后 的 物 理 化 学 性 质<br />
TEST DESCRIPTION<br />
测 试 方 法 描 述<br />
TEST METHOD<br />
测 试 方 法<br />
Glass Transition Temperature<br />
玻 璃 化 转 变 温 度<br />
120℃ TMA Penetration mode/TMA 传 透 法 ATM-0058<br />
Coefficient of Thermal<br />
Expansion/ 热 膨 胀 系 数<br />
Below Tg<br />
Above Tg<br />
40ppm/℃<br />
150ppm/℃<br />
TMA expansion mode<br />
ATM-0055<br />
Dynamic Tensile Modulus<br />
动 态 拉 伸 模 量<br />
@-65℃<br />
@25℃<br />
@150℃<br />
@250℃<br />
4400 MPa (640 Kpsi)<br />
3900 MPa (570 Kpsi)<br />
2000 Mpa (290 Kpsi)<br />
300 Mpa (44 Kpsi)<br />
Dynamic Mechanical Thermal Analysis<br />
using
ABLEBOND <strong>84</strong>-<strong>1LMISR4</strong><br />
APPLICATIN GUIDELINES<br />
Shipment<br />
This Ablestik product is packed and<br />
shipped in dry ice at -80 ℃ . Inside<br />
every dry ice shipment of Ablestik's<br />
products is a small packet containing<br />
the ABLECUBE. This is a small blue<br />
cube which retains its shape at -40℃.<br />
If the ABLECUBE is exposed to<br />
temperatures higher than -40 ℃ , the<br />
cube will melt.<br />
Please check the state of the<br />
ABLECUBE to ensure the integrity of<br />
the shipment. If the ABLECUBE has<br />
melted upon Receiving Inspection,<br />
place the entire shipment in a -40℃<br />
freezer and contact your Ablestik<br />
Customer Service or Sales<br />
Representative.<br />
Unpacking<br />
Transfer the syringes from the dry ice<br />
to a -40 ℃ freezer without ANY<br />
delays. Freezethaw voids will form in<br />
the syringes if the syringes are<br />
repeatedly thawed and refrozen.<br />
Storage<br />
This Ablestik product should be stored<br />
at -40℃. If stored at these conditions,<br />
Ablebond <strong>84</strong>-<strong>1LMISR4</strong> adhesive may<br />
be usable for up to one (1) year.<br />
Alternate storage conditions may be<br />
used as follows:<br />
Storage<br />
Syringes Jars<br />
Temperature<br />
1 month<br />
0℃ to +5℃ 8 days<br />
-15℃ to -10℃ 2 months<br />
*<br />
6<br />
months*<br />
* Jar rolling required<br />
The shelf life of the material is only<br />
valid when the material has been<br />
stored at the correct storage condition.<br />
Incorrect storage conditions will<br />
degrade the performance of the<br />
material in both handling (e.g.<br />
dispensing) and final cured properties.<br />
使 用 说 明<br />
运 输<br />
在 包 装 和 运 输 过 程 中 , 该 产 品 放 在 -<br />
80 ℃ 的 干 冰 中 。 在 所 有 干 冰 运 输<br />
Ablestik 产 品 的 小 包 装 内 都 装 有<br />
ABLECUBE 。 ABLECUBE 是 一 种<br />
蓝 色 的 立 方 体 , 可 以 在 -40℃ 以 下 保<br />
持 形 状 不 变 。 当 温 度 高 于 -40℃ 时 ,<br />
ABLECUBE 将 会 融 化 变 形 。<br />
请 及 时 检 查 ABLECUBE 的 状 态 ,<br />
以 确 保 运 输 的 可 靠 性 。 如 果 检 查 发<br />
现 ABLECUBE 已 经 融 化 , 请 将 所<br />
有 的 产 品 放 在 -40℃ 冰 箱 中 , 并 与<br />
Ablestik 客 户 服 务 或 销 售 代 表 联 系 。<br />
拆 封<br />
从 干 冰 中 将 针 筒 取 出 , 并 立 即 放 入 -<br />
40℃ 的 冰 箱 中 。 如 果 针 筒 被 重 复 回<br />
温 、 二 次 冷 冻 , 产 品 会 发 生 冷 冻 回<br />
温 气 泡 。<br />
贮 藏<br />
该 产 品 应 该 在 -40℃ 以 下 贮 藏 。 在 上<br />
述 的 贮 藏 条 件 下 ,Ablebond <strong>84</strong>-<br />
<strong>1LMISR4</strong> 可 以 贮 藏 1 年 。 如 果 改 变<br />
贮 藏 条 件 , 其 贮 藏 期 限 如 下 所 示 :<br />
贮 藏 温 度 针 筒 大 口 瓶<br />
0℃ 至 +5℃ 8 天 1 个 月 *<br />
-15℃ 至 -10℃ 2 个 月 6 个 月 *<br />
* Jar rolling required<br />
在 所 要 求 的 贮 藏 条 件 下 可 以 保 证 产<br />
品 的 贮 藏 期 限 。 不 恰 当 的 贮 藏 条 件<br />
会 造 成 产 品 加 工 性 能 ( 如 : 点 胶 性<br />
或 者 印 刷 性 能 ) 以 及 固 化 后 的 使 用<br />
性 能 的 降 低 。<br />
09/03 - 3 -
ABLEBOND <strong>84</strong>-<strong>1LMISR4</strong><br />
Thawing<br />
Allow the container to reach room<br />
temperature before use. After<br />
removing from the freezer, set the<br />
syringes vertically for thawing. Refer<br />
to Syringe Thaw Time chart below for<br />
the thaw time recommendation.<br />
DO NOT open the container before<br />
contents reach ambient temperature.<br />
Any moisture that collects on the<br />
thawed container should be removed<br />
prior to opening the container.<br />
DO NOT re-freeze. Once thawed to<br />
room temperature, the adhesive should<br />
not be refrozen.<br />
Adhesive Application<br />
Thawed adhesive should be<br />
immediately placed on dispense<br />
equipment for use. If the adhesive is<br />
transferred to a final dispensing<br />
reservoir, care must be exercised to<br />
avoid entrapment of contaminants<br />
and/or air into the adhesive. Adhesive<br />
must be completely used within the<br />
18-hour period. Silver-resin separation<br />
may occur if the adhesive is left out at<br />
ambient beyond the recommended<br />
work life.<br />
Apply enough adhesive to achieve a<br />
25-50 μ m (1-2 mil) wet bondline<br />
thickness, dispensed with<br />
approximately 25%-50% filleting on<br />
all sides of the die. Alternate dispense<br />
amounts may be used depending on<br />
the application requirements. Star or<br />
cross-shaped dispense patterns will<br />
yield fewer bondline voids than the<br />
matrix style of the dispense pattern.<br />
Contact the Ablestik Technical Service<br />
Department for detailed<br />
recommendations on adhesive<br />
application, including dispensing.<br />
回 温<br />
本 产 品 在 使 用 之 前 , 先 将 其 回 温 至<br />
室 温 。 在 冰 箱 中 取 出 后 , 将 针 筒 垂<br />
直 地 放 置 进 行 回 温 。 请 参 照 下 面 的<br />
针 筒 回 温 流 程 以 了 解 推 荐 的 回 温 时<br />
间 。<br />
在 产 品 回 温 至 室 温 之 前 , 不 要 将 容<br />
器 打 开 。 任 何 在 回 温 过 程 中 凝 集 在<br />
容 器 上 的 水 汽 都 必 须 在 打 开 容 器 之<br />
前 清 除 掉 。<br />
严 禁 二 次 回 温 。 一 旦 回 温 至 室 温 ,<br />
该 产 品 不 能 进 行 再 次 冷 冻 。<br />
产 品 操 作 说 明<br />
回 温 后 的 胶 必 须 立 即 放 在 点 胶 设 备<br />
上 加 以 使 用 。 如 果 需 要 把 胶 转 移 到<br />
后 期 点 胶 器 里 面 , 要 小 心 操 作 , 切<br />
忌 在 转 移 过 程 中 带 入 杂 质 或 空 气 。<br />
回 温 后 的 胶 必 须 在 18 小 时 内 全 部 使<br />
用 完 。 超 出 工 作 时 间 后 , 放 置 在 室<br />
温 下 的 胶 会 发 生 银 粒 子 与 树 脂 的 分<br />
离 。<br />
滴 加 足 够 的 胶 , 使 之 形 成 25-50 μ<br />
m(1-2 mil) 的 湿 胶 层 厚 度 , 并 且 芯 片<br />
四 周 的 胶 层 倒 角 高 度 近 似 为 25%-<br />
50%。 可 以 根 据 使 用 要 求 来 调 整 点<br />
胶 量 。 星 型 或 十 字 型 图 案 的 点 胶 方<br />
式 比 矩 阵 型 的 点 胶 方 式 的 胶 层 气 泡<br />
少 。<br />
请 联 系 Ablestik 的 技 术 服 务 部 门 咨 询<br />
包 括 点 胶 操 作 在 内 的 产 品 使 用 说 明<br />
书 。<br />
09/03 - 4 -
ABLEBOND <strong>84</strong>-<strong>1LMISR4</strong><br />
Cure<br />
Ablebond <strong>84</strong>-<strong>1LMISR4</strong> adhesive<br />
should be cured in conventional box<br />
oven per the recommended cure<br />
condition. Refer to the Cure Process<br />
Data section of the Technical Data<br />
Sheet for the recommended cure<br />
cycles.<br />
For the recommended cure cycle, the<br />
oven should be pre-heated to 175℃<br />
before introducing the lead frame<br />
magazines.<br />
AVAILABILITY<br />
Ablebond ® adhesives are packaged in<br />
syringes or jars per customer<br />
specification. Available package sizes<br />
range from 1cc to 30cc and 1 ounce to<br />
1 pound. For details, refer to the<br />
Ablestik Standard Package Data Set,<br />
or contact your Customer Service<br />
Representative.<br />
固 化<br />
Ablebond <strong>84</strong>-<strong>1LMISR4</strong> 应 该 在 每 一<br />
个 推 荐 的 条 件 下 使 其 在 传 统 烘 箱 中<br />
固 化 。 请 参 考 技 术 数 据 表 中 的 固 化<br />
制 程 了 解 推 荐 的 循 环 固 化 过 程 。<br />
对 于 所 推 荐 的 循 环 固 化 股 过 程 , 应<br />
该 在 将 框 架 放 入 之 前 将 烘 箱 加 热 到<br />
175℃。<br />
包 装 规 格<br />
按 照 客 户 的 要 求 ,ABLEBOND ® 系<br />
列 的 胶 可 以 装 在 针 筒 中 , 或 者 大 口<br />
瓶 中 。 包 装 规 格 可 以 从 1cc 到 30cc<br />
不 等 , 以 及 1 英 镑 重 的 包 装 。 详 细<br />
情 况 可 以 参 考 Ablestik 标 准 包 装 数 据<br />
或 者 与 当 地 客 户 服 务 代 表 联 系 。<br />
09/03 - 5 -
ABLEBOND <strong>84</strong>-<strong>1LMISR4</strong><br />
20021 Susana Road, Rancho Dominguez, CA 90221<br />
(310) 764-4600 Fax (310) 764-2545 CUSTOMER SERVICE FAX (310) 764-1783<br />
For a technical contact nearest you, visit<br />
www.ablestik.com<br />
The information given and the recommendations made herein are believed to be accurate but no guarantee of their<br />
accuracy is made. In every case we recommend that purchasers before using any product conduct their own tests<br />
to determine whether the product is suitable for their particular purposes under their own operating conditions. No<br />
representative of ours has any authority to waive or change the foregoing provisions but, subject to such<br />
provisions, our engineers are available to assist purchasers in adapting out products to their needs. Nothing<br />
contained herein shall be construed to imply the non-existence of any relevant patents or to constitute a permission,<br />
inducement or recommendation to practice any invention covered by any patent, without the authority from the<br />
owner of this patent. These materials are not designed or manufactured for implantation in the human body.<br />
Approval from FDA for such use as part of any product to be implanted in the human body has NOT been sought<br />
nor received. We also expect purchasers to use our products in accordance with the guiding principles of the<br />
American chemistry Council’s Responsible Care ® program.<br />
09/03 - 6 -