ABLEBOND® 84-1LMISR4
ABLEBOND® 84-1LMISR4
ABLEBOND® 84-1LMISR4
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
ABLEBOND <strong>84</strong>-<strong>1LMISR4</strong><br />
Thawing<br />
Allow the container to reach room<br />
temperature before use. After<br />
removing from the freezer, set the<br />
syringes vertically for thawing. Refer<br />
to Syringe Thaw Time chart below for<br />
the thaw time recommendation.<br />
DO NOT open the container before<br />
contents reach ambient temperature.<br />
Any moisture that collects on the<br />
thawed container should be removed<br />
prior to opening the container.<br />
DO NOT re-freeze. Once thawed to<br />
room temperature, the adhesive should<br />
not be refrozen.<br />
Adhesive Application<br />
Thawed adhesive should be<br />
immediately placed on dispense<br />
equipment for use. If the adhesive is<br />
transferred to a final dispensing<br />
reservoir, care must be exercised to<br />
avoid entrapment of contaminants<br />
and/or air into the adhesive. Adhesive<br />
must be completely used within the<br />
18-hour period. Silver-resin separation<br />
may occur if the adhesive is left out at<br />
ambient beyond the recommended<br />
work life.<br />
Apply enough adhesive to achieve a<br />
25-50 μ m (1-2 mil) wet bondline<br />
thickness, dispensed with<br />
approximately 25%-50% filleting on<br />
all sides of the die. Alternate dispense<br />
amounts may be used depending on<br />
the application requirements. Star or<br />
cross-shaped dispense patterns will<br />
yield fewer bondline voids than the<br />
matrix style of the dispense pattern.<br />
Contact the Ablestik Technical Service<br />
Department for detailed<br />
recommendations on adhesive<br />
application, including dispensing.<br />
回 温<br />
本 产 品 在 使 用 之 前 , 先 将 其 回 温 至<br />
室 温 。 在 冰 箱 中 取 出 后 , 将 针 筒 垂<br />
直 地 放 置 进 行 回 温 。 请 参 照 下 面 的<br />
针 筒 回 温 流 程 以 了 解 推 荐 的 回 温 时<br />
间 。<br />
在 产 品 回 温 至 室 温 之 前 , 不 要 将 容<br />
器 打 开 。 任 何 在 回 温 过 程 中 凝 集 在<br />
容 器 上 的 水 汽 都 必 须 在 打 开 容 器 之<br />
前 清 除 掉 。<br />
严 禁 二 次 回 温 。 一 旦 回 温 至 室 温 ,<br />
该 产 品 不 能 进 行 再 次 冷 冻 。<br />
产 品 操 作 说 明<br />
回 温 后 的 胶 必 须 立 即 放 在 点 胶 设 备<br />
上 加 以 使 用 。 如 果 需 要 把 胶 转 移 到<br />
后 期 点 胶 器 里 面 , 要 小 心 操 作 , 切<br />
忌 在 转 移 过 程 中 带 入 杂 质 或 空 气 。<br />
回 温 后 的 胶 必 须 在 18 小 时 内 全 部 使<br />
用 完 。 超 出 工 作 时 间 后 , 放 置 在 室<br />
温 下 的 胶 会 发 生 银 粒 子 与 树 脂 的 分<br />
离 。<br />
滴 加 足 够 的 胶 , 使 之 形 成 25-50 μ<br />
m(1-2 mil) 的 湿 胶 层 厚 度 , 并 且 芯 片<br />
四 周 的 胶 层 倒 角 高 度 近 似 为 25%-<br />
50%。 可 以 根 据 使 用 要 求 来 调 整 点<br />
胶 量 。 星 型 或 十 字 型 图 案 的 点 胶 方<br />
式 比 矩 阵 型 的 点 胶 方 式 的 胶 层 气 泡<br />
少 。<br />
请 联 系 Ablestik 的 技 术 服 务 部 门 咨 询<br />
包 括 点 胶 操 作 在 内 的 产 品 使 用 说 明<br />
书 。<br />
09/03 - 4 -