WATERPROOF LAYER PROTEADUO TRIARMATO Multi-layer composite polymer-bitumen waterproofing membrane, 4 mm thick, such as PROTEADUO TRIARMATO, certified with the EuroAgrément I.T.C-CNR (former I.C.I.T.E.), made up of an upper layer in elastoplastomeric polymer bitumen with ring and ball softening point (EN 1427) of 150°C, a lower layer in elastomeric polymer bitumen with elastic recovery (NF XP 84-360) of 300% and a stabilised three-layer composite reinforcement with fibreglass between two spunbond polyester “non-woven fabrics”, impregnated with elastomeric polymer bitumen. The membrane has a tensile strength (EN 12311-1) L/T of 750/650 N/50 mm, ultimate elongation (EN 12311-1) L/T of 50/50%, resistance to tearing (EN 12310-1) L/T of 250/250 N and cold flexibility (EN 1109) of the upper layer of -15°C and of the lower layer of -25°C. MINERAL PROTEADUO TRIARMATO Multi-layer composite polymer-bitumen waterproofing membrane, covered with slate granules, 4 mm thick measured on the selvage, such as MINERAL PROTEADUO TRIARMATO, certified with the EuroAgrément I.T.C-CNR (former I.C.I.T.E.), made up of an upper layer in elastoplastomeric polymer bitumen with ring and ball softening point (EN 1427) of 150°C, a lower layer in elastomeric polymer bitumen with elastic recovery (NF XP 84-360) of 300% and a stabilised three-layer composite reinforcement with fibreglass between two spunbond non-woven polyester fabrics, impregnated with elastomeric polymer bitumen. The membrane has a tensile strength (EN 12311-1) L/T of 750/650 N/50 mm, ultimate elongation (EN 12311-1) L/T of 50/50%, resistance to tearing (EN 12310-1) L/T of 250/250 N and cold flexibility (EN 1109) of the upper layer of -15°C and of the lower layer of -25°C. HELASTA POLYESTER Elastomeric polymer-bitumen waterproofing membrane, 4 mm thick, with a radial butadiene-styrene thermoplastic rubber base and distilled bitumen base, with ultimate elongation of 2000% and elastic recovery (NF-XP 84-360) of 300%, reinforced with spunbond polyester non-woven fabric, such as HELASTA POLYESTER 4, certified with the Agrément I.T.C-CNR (former I.C.I.T.E.). The membrane has a tensile strength (EN 12311-1) L/T of 900/700 N/50mm, ultimate elongation (EN 12311-1) L/T of 50/50 %, resistance to tearing (EN 12310-1) L/T of 200/200 N, fatigue resistance (UEAtc) of over 1,000 cycles on new material and over 500 cycles on artificially aged material, cold flexibility (EN1109) of -25°C and hot stability (EN1110) of 100°C. MINERAL HELASTA POLYESTER Elastomeric polymer-bitumen waterproofing membrane, covered with slate granules, 4 mm thick measured on the selvage, with a radial butadiene-styrene thermoplastic rubber base and distilled bitumen base, with ultimate elongation of 2000% and elastic recovery (NF-XP 84-360) of 300%, reinforced with spunbond polyester non-woven fabric, such as MINERAL HELASTA POLYESTER 4, certified with the Agrément I.T.C-CNR (former I.C.I.T.E.). The membrane has a tensile strength (EN 12311-1) L/T of 900/700 N/50mm, ultimate elongation (EN 12311-1) L/T of 50/50 %, resistance to tearing (EN 12310-1) L/T of 200/200 N, fatigue resistance (UEAtc) of over 1,000 cycles on new material and over 500 cycles on artificially aged material, cold flexibility (EN1109) of -25°C and hot stability (EN1110) of 100°C. FLEXTER TESTUDO SPUNBOND POLYESTER Elastoplastomeric polymer-bitumen waterproofing membrane, 4-mm thick, based on distilled bitumen, plastomers and elastomers, with composite reinforcement consisting of spunbond non-woven polyester fabric stabilised with fibreglass, FLEXTER TESTUDO SPUNBOND POLYESTER 4, certified with the Agrément ITC- CNR (former ICITE). The membrane has a tensile strength (EN 12311-1) L/T of 850/700 N/50mm, ultimate elongation (EN 12311-1) L/T of 50/50 %, resistance to tearing (EN 12310-1) L/T of 150/150 N, resistance to impact ( EN 12691 - method A) of 1,250 mm, resistance to static load (EN 12730) of 15 kg, hot dimensional stability (EN 1107-1), L/T of ±0,3/±0,3%, cold flexibility (EN1109) of -20°C and heat resistance (EN1110) of 140°C. MINERAL FLEXTER TESTUDO SPUNBOND POLYESTER Elastoplastomeric polymer-bitumen waterproofing membrane, self-protected with slate granules, 4 mm thick measured on the selvage, based on distilled bitumen, plastomers and elastomers, with composite reinforcement consisting of spunbond non-woven polyester fabric stabilised with fibreglass, MINERAL FLEXTER TESTUDO SPUNBOND POLYESTER 4 type, certified with the Agrément ITC-CNR (former ICITE). The membrane has a tensile strength (EN 12311-1) L/T of 850/700 N/50mm, ultimate elongation (EN 12311-1) L/T of 50/50 %, resistance to tearing (EN 12310-1) L/T of 150/150 N, hot dimensional stability (EN 1107-1), L/T of ±0,3/±0,2%, cold flexibility (EN1109) of -20°C and heat resistance (EN1110) of 140°C. MINERAL REFLEX WHITE FLEXTER TESTUDO SPUNBOND POLYESTER An elastoplastomeric polymer-bitumen waterproofing membrane, such as MINERAL REFLEX WHITE FLEXTER TESTUDO SPUNBOND POLYESTER 4, with special high saturation and luminosity white mineral self-protection for energy saving and the reduction of “urban heat islands”. It has high solar reflectance and very high thermal emissivity, 4 mm thick measured on the selvage, with a distilled bitumen, plastomer and elastomer base, with composite reinforcement in spunbond “non woven” polyester fabric stabilised with fibreglass, certified with Agrément I.T.C.- CNR (former I.C.I.T.E.). The membrane, with a Solar Reflectance index according to the wind SRI = 52-54%, has a tensile strength (EN 12311-1) L/T of 850/700 N/50mm, ultimate elongation (EN 12311-1) L/T of 50/50 %, resistance to tearing (EN 12310-1) L/T of 150/150 N, hot dimensional stability (EN 1107-1), L/T of ±0,3/±0,2%, cold flexibility (EN1109) of -20°C and heat resistance (EN1110) of 140°C. Fire-resistant version MINERAL REFLEX WHITE FLEXTER TESTUDO FR TRIARMATO Fire Resistance elastoplastomeric polymer-bitumen waterproofing membrane, certified as compliant with EN 13501-5 in classes: Broof (t1), Broof (t3), Broof (t4). It has special high saturation and luminosity white mineral self-protection for energy saving and the reduction of “urban heat islands” with high solar reflectance and very high thermal emissivity, 4 mm thick measured on the selvage, with a distilled bitumen, plastomer and elastomer base, with composite triple reinforcement in spunbond “non woven” polyester fabric stabilised with fibreglass, such as MINERAL REFLEX WHITE FLEXTER TESTUDO FR TRIARMATO 4, certified with Belgian Agrément UBatc ATG 1616. The membrane, with a Solar Reflectance index according to the wind SRI = 52-54%, has a tensile strength (EN 12311-1) L/T of 750/650 N/50mm, ultimate elongation (EN 12311-1) L/T of 50/50 %, resistance to tearing (EN 12310-1) L/T of 250/250 N, hot dimensional stability (EN 1107-1), L/T of ±0.25/±0.1%, cold flexibility (EN1109) of -15°C and heat resistance (EN1110) of 140°C. 22 NON-WALKABLE FLAT ROOF <strong>Technical</strong> <strong>specification</strong>s
<strong>Technical</strong> <strong>specification</strong>s WATERPROOF LAYER MINERAL DESIGN TRIARMATO Elastoplastomeric polymer bitumen multi-functional waterproofing membrane, with prefabricated stabilised three-layer composite reinforcement consisting of a fibreglass mat between two spunbond non-woven polyester fabrics, such as MINERAL DESIGN TRIARMATO SPUNBOND POLYESTER. Produced in different types of patterns obtained by combining two types of different colours of ceramic-coated mineral granules for the decoration and development of the design of roofs with visible coverings. The membrane has a mass per unit area (EN 1849-1) of 4.5 kg/m 2 , tensile strength (EN 12311-1) L/T of 750/650 N/50 mm, ultimate elongation (EN 12311-1) L/T of 50/50%, resistance to tearing (EN 12310-1) L/T of 250 N, hot dimensional stability (EN 1107-1) L/T of ±0,2/±0,1%, cold flexibility (EN 1109) of -15°C and heat resistance (EN 1110) of 120°C. 1. CHECKERBOARD 2. TILES Mineral Design decoration table 3. CANADIAN SLATE 4. OVAL CANADIAN SLATE HIGH REFLECTANCE AND HIGH EMISSIVITY PAINT WHITE REFLEX One-component white paint, based on polymers in an aqueous emulsion and special additives, flexible, resistant to atmospheric agents, with high solar reflectance and emissivity of infrared rays, able to increase the diffused light and the efficiency of the photovoltaic panels, to reduce the surface temperature of the waterproof covering during the daytime, promote the dissipation of the heat accumulated during the night and consequently produce consistent energy saving from air conditioning buildings. The paint has solar reflectance (ASTM C-1549) > 0.80, infrared emissivity (ASTM C-1471) > 0.85 and a Solar Reflectance <strong>Index</strong> SRI > 90%. 5. BRICKS 6. RHOMBUS 7 MILITARY CAMOUFLAGE NON-WALKABLE FLAT ROOF 23
Change language