B/W CCD Camera Model CS8600 Series ... - Site ftp Elvitec

B/W CCD Camera
Model CS8600 Series
Specifications
TOKYO ELECTRONIC INDUSTRY CO.,LTD.
2000-11-20

1. Product Description
The model CS8600 series are ultra-compact and light-weight B/W CCD cameras designed for
FA (factory automation), image measurement, microscopic, and other various applications.
2. Features
(1)High resolution
Its 380,000-pixel (EIA) CCD (CCIR: 440,000) achieves the horizontal resolution of 570TV
lines (CCIR: 560TV lines), ensuring high-quality images of high density with less moire fringes
or beatings.
(2)Ultra-compact and light-weight body
The integrated body, composed of a camera-head part and a CCU part, is designed to be highly
compact and light in weight. Just by supplying DC12V power, the camera can start to capture
image.
(3)Electronic shutter
With the built-in electronic shutter function, each model captures the images of fast-moving
object without much after-images.
(4)AGC
Thanks to AGC (Automatic Gain Control) functions, these cameras can obtain optimal images
even against severe changes in the amount of incoming light under illumination-fluctuating
shooting conditions (AGC ON / OFF selectable via inner SW).
(5)Restart / Reset
With the restart / reset functions set ON, images are captured at given timing cued by VD input
(R.R. ON / OFF selectable via inner SW).
(6)SS (Special Shutter) & RTS (Random Trigger Shutter)
These cameras are equipped with the special-shutter and random-trigger-shutter, which starts
light-exposure synchronizing with external trigger signal input. This function allow these
cameras to capture images at any user-defined timing (ON / OFF selectable via inner SW).
(7)Near-infrared region shooting capabilities
A near-infrared-region-sensitive CCD is integrated in the model CS8xxxI in this series. This
model can shoot clearly even under such condition.
CS8xxx Series Spec Lookup Table
Model Name CCD Type TV Format Near-infrared Special Restart / Reset
Shutter &
RTS
CS8620 1/2 type EIA X X
CS8620H 1 1/2 type EIA X X X
CS8630 1/3 type EIA X X
CS8630H 1/3 type EIA X X X
CS8620C 1/2 type CCIR X X
CS8620HC 1/2 type CCIR X X X
CS8630C 1/3 type CCIR X X
CS8630HC 1/3 type CCIR X X X
3. Configuration
1

Quantity
(1)CCD camera body 1
(2)Accessory
Operation manual 1
4. Specifications
Model
CS8600 series
(1)TV system (Model name without suffix) EIA format
(Model name with suffix C)
CCIR format
(2)Image sensor
Interline CCD
(CS8620)
ICX038DLA
(CS8620C)
ICX039DLA
(CS8630)
ICX058CL
(CS8630C)
ICX059CL
(CS8620H)
ICX248AL
(CS8620HC)
ICX249AL
(CS8630H)
ICX258AL
(CS8630HC)
ICX259AL
Active pixel number (EIA) 768(H) x 494(V)
(CCIR)
752(H) x 582(V)
Cell size (CS8620, CS8620H) 8.4 x 9.8 micro m
(CS8620C, CS8620HC) 8.6 x 8.3 micro m
(CS8630, CS8630H)
6.35 x 7.4 micro m
(CS8630C, CS8630HC) 6.5 x 6.25 micro m
Scanning area (CS8620, CS8620C, 6.5 x 4.85 mm
CS8620H, CS8620HC)
(=Equivalent to 1/2" pickup tube)
(CS8630, CS8630C,
4.8 x 3.6 mm
CS8630H, CS8630HC)
(=Equivalent to 1/3" pickup tube)
H driving frequency [Internal sync]
(EIA)
14.31818MHz plus/ minus 100ppm
(CCIR)
14.1875MHz plus/ minus 100ppm
(3)Scanning lines (EIA) 525 lines
(CCIR)
625 lines
(4)Scanning format 2:1 interlace
(5)Sync system
Internal / External synchronization (Automatic change-over)
(6)Scanning frequency (EIA) Horizontal: 15.734kHz p/m 100ppm
Vertical: 59.94Hz p/m 100ppm
(CCIR)
Horizontal: 15.625kHz p/m 100ppm
Vertical: 50.0Hz p/m 100ppm
(7)Aspect ratio 4:3
(8)Subject illumination Standard : GAIN: MGC, Gamma = 1.0
(CS8620, CS8620C) 400 lx, F5.6 (3100K)
(CS8630, CS8630C) 400 lx, F4 (3100K)
(CS8620H, CS8620HC) 400 lx, F 11 (3100K)
(CS8630H, CS8630HC) 400 lx, F8 (3100K)
Minimum : GAIN: MAX, Gamma= 0.45
(CS8620, CS8620C) 0.3 lx, F1.4
(CS8630, CS8630C) 0.3 lx, F 1.4
2

(CS8620H, CS8620HC) 0.1 lx, F1.4
(CS8630H, CS8630HC) 0.2 lx, F1.4
(9)Video output
VS: 1.0V(p-p)/75-ohm terminated
(10)Resolution (EIA) 570TV lines(H)
485 lines (350TV lines)(V)
(CCIR)
560TV lines(H)
575 lines (410TV lines)(V)
(11)S/N ratio 60dB(p-p)/rms (GAIN: FIX, Gamma = 0)
(12)Input signal
-1. Ex-sync signal HD.VD/SYNC/VS
Input level
HD.VD/SYNC: From 2 through 6V(p-p)
VS: 1.0V(p-p) [SYNC: 0.3V(p-p)]
Input impedance 75-ohm/High: Switch-able by an inner SW
(Initial factory setting: High)
Operation
2 : 1 interlace
Polarity
Negative
Pulse width
HD: 6.4 plus / minus 3 micro S
VD: From 150 through 800 micro S
Repeating frequency (EIA) fH = 15.734kHz p/m 2 percent
fV = 2fH/525
(CCIR)
fH = 15.625kHz p/m 2 percent
fV = 2fH/625
Scanning lines (EIA) 525 lines
Phase difference
(CCIR)
625 lines
The difference in phase between the falling edge of VD and
that of HD is shown in the figure below.
-2. Shutter trigger (TRIG)
Input level VL = From 0 through 0.5V
VH = From 2 through 5 V
Input impedance High impedance
Polarity
Positive
Pulse width
From 2 micro S through 1/4 S
(13 )Output signal
-1. HD VD signal Under internal sync operation, output available by inner
switch selection (Initial factory setting: OFF)
Output level
4.5 V(p-p) (Under no load)
Operation
2 : 1 interlace
Polarity
Negative
Pulse width (EIA) HD: 6.36 plus / minus 1 micro S
VD: 572 plus / minus 1 micro S
(CCIR)
HD: 6.41 plus / minus 1 micro S
VD: 480 plus / minus 1 micro S
Repeating frequency (EIA) fH=15.73426kHz p/m 100ppm
(CCIR)
Scanning lines (EIA) 525 lines
(CCIR)
625 lines
fV=2fH/525
fH=15.625kHz p/m 100ppm
fV=2fH/625
3

-2. CLOCK signal Output available by inner switch selection
(Initial factory setting: OFF)
Output level
2.5 V(p-p) (Under no load)
Repeating frequency (EIA) 14.318181 MHz p/m 100ppm
(Under internal sync)
(CCIR)
14.875MHz p/m 100ppm
(Under internal sync)
(14)Sensitivity setting Mode selection via panel SW
(Initial factory setting: MGC)
AGC (Automatic Gain Control)
MGC (Manual Gain Control)
(15)AGC
Video output fluctuation level within plus / minus 2dB
against the fluctuation of incoming light amount ranging
from 6dB-over through 12dB-under the standard subject
illumination level.
(16)MGC
Manual sensitivity adjustment available
(17)Gamma
1.0 / 0.45 selectable via inner SW
(Initial factory setting: 1.0)
(18)White-clip
(19)Electronic shutter
Clip-level: 820mV(p-p) (Excluding SYNC)
Normal shutter
ON /OFF selectable via panel SW
Shutter-speed selection available among; Normal, 1/125,
1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000s, and
Flicker-less (Initial factory setting: 1/1000s)
(20)Random trigger shutter RTS Mode selection available
1 TRIG Pulse Width
HD/VD IN
(Consecutive)
SYNC
Non-reset
2 TRIG Pulse Width
HD/VD IN
(Consecutive)
SYNC
Non-reset
3 TRIG Pulse Width
SYNC
Non-reset
4
Shutter-speed
Selection
HD/VD IN
(Consecutive)
SYNC
Non-reset
5
Shutter-speed
Selection
HD/VD IN
(Consecutive)
SYNC
Non-reset
6
Shutter-speed
Selection Internal sync
SYNC
Non-reset
7 TRIG Pulse Width Internal sync SYNC
8 Shutter-speed Internal sync SYNC
*Mode#4: Same function as CS8420RTS random shutter
(21)Special shutter User-defined shutter-tuning and shutter-speed cued and timed
by shutter trigger and restart /reset pulse input ON / OFF
selectable via inner SW (Initial factory setting: OFF)
(22)CCD storage mode Field / Frame storage (integration)
Switch-able by inner SW selection
(initial factory setting: frame storage)
(23)Restart / Reset Restart / Reset function available via panel SW selection
(Initial factory setting: OFF)
(24)Power supply DC12V (plus minus 10%)
[Ripple level: Less than 10mV(p-p)]
(25)Power consumption approx. 1.6W
4

(26)Ambient condition
(27)Lens mount
(28)Flange-back
(29)External dimension
(30)Weight
(31)Option unit
Operation assurance;
Temperature: From -10 through 50 degree Celsius
Humidity: From 20 through 80 percent
(No condensing)
C mount
17.526mm
29(W) x 29(H) x 32(D)mm (Excluding protruding part)
Approximately 50g
Power adapter
CA 130B, CA150 (AC 100V)
CA140B (AC220V)
Power / Video connector
HR10A-10P-12S (Manufactured by HIROSE)
Camera cable
DC IN / SYNC cable (With plugs)
3m, 5m, and 10m
Tripod mounting hardware
IR cut filter
(32)DC IN / SYNC connector Compatible plug: HRIOA-IOP-12S
(Manufactured by HIROSE DENKI)
Pin assignment
External sync operation
Pin No. HD/VD VS/SYNC Restart / Reset Internal sync
1 GND GND GND GND
2 12V +12V +12V +12V
3 GND GND GND GND
4 VIDEO OUT VIDEO OUT VIDEO OUT VIDEO OUT
5 GND GND GND GND
6 HD IN --- HD IN HD OUT(*)
7 VD IN VS/SYNC IN R.R. IN VD OUT(*)
8 GND GND GND GND
9 CLK OUT CLK OUT CLK OUT CLK OUT
10 WEN OUT WEN OUT --- WEN OUT
11 TRIG IN TRIG IN TRIG IN TRIG IN
12 GND GND GND GND
HD / VD output is available via inner SW selection
under internal sync operation.
5

HD/VD Phase Difference
The phase-difference between the HD / VD falling edge of VD is shown in figure below.
EIA first field
CCIR first field
EIA second field
CCIR second field
t1=0±5µS
t2=1/fH/2±5µS
5. External-view Drawing
6