WARP9 - Kim Lighting

SITE /ROADWAY 

WARP9 

TM 

The first outdoor luminaire designed 

not to be seen, using Visual Stealth Technology. TM

TM 

THE FUTURE OF SITE/ROADWAY LIGHTING 

Kim’s Theory of Relativity 

A Concealment Approach 

Low Visual Signature Technology 

Advanced Performance Features 

Optical Design Features 

Mechanical Features 

Installation & Maintenance Features 

Ordering Information 

Luminaire Specifications 

Lamp Guide 

2 

4 

6 

8 

10 

12 

14 

16 

18 

20 

MAILING ADDRESS 

P.O. BOX 60080 

CITY OF INDUSTRY, CA 

91716-0080 

BUSINESS ADDRESS 

16555 EAST GALE AVENUE 

CITY OF INDUSTRY, CA 91745 

PHONE: 626.968.5666 

FAX: 626.369.2695 

ENTIRE CONTENTS 

© COPYRIGHT 2011 KIM LIGHTING INC. 

ALL RIGHTS RESERVED 

REPRODUCTION IN WHOLE OR IN PART 

WITHOUT PERMISSION IS STRICTLY PROHIBITED. 

U.S. PATENT D568,521 

www.kimlighting.com 

Printed in U.S.A. 

5508811200 

Version 1.3 (7/19/11) 

Hubbell 

Lighting, Inc.

WARP9 TM 

Fixture/Background 

photo 

Low Visual Signature Luminaire 

WARP9 is a new concept in luminaire design – visual stealth. Typical site lighting attempts to 

embellish, decorate, or adorn, often beyond the original architectural intent. WARP9 was 

conceived and developed with an entirely different directive. WARP9 was designed to disappear 

from the site, camouflage itself within its surroundings, and avoid detection from daytime visual 

perception. WARP9 is the antithesis of massive, showy, recognizable, and ornamental design, 

allowing architecture to remain visually dominant as it was originally intended. WARP9 

is a concept that is long overdue, yet one that is light years ahead of its time. 

KIM LIGHTING 1


Kim’s Theory of Relativity 

The Complete Design Solution 

From Parking Lot to Building • Proper Scale • Coordinated Design 

Site/Roadway Zone 

Parking lots and roadways require luminaires on 

20'-40' poles to efficiently light these large areas. 

Therefore, this lighting sets the design style for all 

other lighting zones as you progress towards the 

building. Select WARP9L large version luminaires 

with round poles for this zone. 

Pedestrian Zone 

As an observer leaves the parking lot and transitions 

to pedestrian areas, poles should decrease in height to 

10' – 16'. In addition, luminaires should decrease in 

scale, as human perception of proportion is keen at 

this level. Select WARP9’s small version luminaires for 

this zone, and select a finish that will integrate well 

with the fixture’s primary background elements. 

2 KIM LIGHTING


Landscape/Pathway Zone 

Near the building, luminaires should continue to 

disappear, blending into the landscape and hardscape 

elements. Select from a wide range of low voltage, line 

voltage, and LED landscape luminaires, or Kim Lighting’s 

VRB and GEM bollard series to integrate 

with WARP9’s curvilinear form. 

Building/Perimeter Zone 

Avoid installing pole-mounted luminaires close to the 

building, as they tend to dominate the architecture. 

However, if required, WARP9 is the best solution to 

integrate with architectural proximity. Kim Lighting 

suggests WARP9 wall mounted luminaires to reduce 

daytime detection of building mounted equipment. 

KIM LIGHTING 3


A Concealment Approach 

WARP9’s efficient and low profile compound curve design results in a close 

synergy between aerodynamic performance, illumination performance, and its 

ability to limit cross section visibility. When installed with the right scale, 

finish and placement, WARP9’s sophisticated and complex camouflage scheme 

achieves a unique level of concealment and subtle presence never before 

offered in an architectural luminaire. 

Product Overview: 

Kim Lighting’s WARP9 series offers a complete package of luminaire sizes 

and options to integrate seamlessly into any environment, natural or 

man-made. Choose from two housing sizes in electronic or magnetic 

ballasted versions, and select one of four distinct light distributions and a 

wide variety of mounting, fixture, and finish options to complete your 

WARP9 visual stealth concept. 

Four Housing Configurations 

WP9SE WP9LE WP9SM WP9LM 

Four Distinct Distributions 

TYPE II TYPE III TYPE IV TYPE V Sq 

Multiple Options 

Wall Mount Pole Mount SLX Lexan ® 

Lens 

4 KIM LIGHTING 

Houseside 

Shield 

Tamper 

Resistant 

Latch 

New 

Stealth Gray TM 

Finish


WP9LE 

WP9LM 

WP9SE 

WP9SM 

KIM LIGHTING 5


Low Visual Signature Technology 

DESIGN LOGIC: 

The Disappearing Act 

Modern technology produced Kim Lighting’s 

new WARP9 luminaires, but the camouflage 

principles behind it were learned instinctively 

from nature thousands of years ago. WARP9’s 

fundamental approach is the same as those 

used by wildlife and hunters for millennia: 

hide, blend, and deceive. 

There are two basic elements of camouflage: 

shape and color. 

WARP9 capitalizes on both of these 

principles in unique ways to reduce 

perceptual attraction and luminaire detection. 

First, WARP9 utilizes a computer generated 

low-profile compound curve design to create 

a natural compact top arc that reflects the 

sky from normal viewing angles. This breaks 

up the luminaire’s outline, disrupting its 

silhouette and evening out its 3-dimensional 

surface, making it more difficult to see as one 

object. This reduces visual mass, and allows 

the viewer to envision the entire site without 

disruptive and massive luminaire shapes to 

draw attention away from architecture and 

landscape. Second, WARP9 utilizes a hollow 

mounting arm that gracefully blends with the 

housing, and minimizes its visual signature. 

Kim Lighting has also developed a unique 

color scheme to further reduce the 

luminaire’s visual signature. 

VISUAL STEALTH TECHNOLOGY : 

New Stealth Gray Finish 

Color is essential to camouflage, as its similarity to 

the primary background will tend to break up that 

area of the outline and blend the shape away from 

normal detection. Over 100 painted samples were 

tested and reviewed to determine how well they 

matched the predominant colors of contemporary 

architecture, typical horizons, and northern 

hemisphere skies. These were then narrowed down 

to a few prototype samples that were field tested 

for visual acuity, perception attraction, and detection 

reduction. The result is Kim Lighting’s new Stealth 

Gray finish option featuring a light gray hue 

suitable for any outdoor environment. However, 

designers can select from a wide variety of standard 

and custom finishes depending on application and 

immediate background surface coloration. 

6 KIM LIGHTING


FPO 

AERODYNAMICS: 

Small Size • Low EPA 

Specify Kim Lighting’s new Stealth Gray finish to 

further reduce the fixture’s visual signature. 

Featuring a light gray semi-gloss surface, Stealth 

Gray is a result of an extensive study of finishes 

and paints for typical application scenarios in 

natural or architectural environments. 

A welcomed result of WARP9’s thin design is a 

very low EPA rating, suitable for installation in 

almost any environment, including high wind, 

coastal, and hurricane prone locations. Kim Lighting 

recommends mounting WARP9 luminaires on 

round poles to further improve aerodynamics 

and lend to the fixture’s camouflaged appearance. 

Round poles have less visual signature than 

square poles. 

WARP9 Small Housing and Arm EPA (WP9SE): 0.52 

WARP9 Large Housing and Arm EPA (WP9LE): 0.95 

Note: Pole selection and height will also 

determine final EPA allowance for your application. 

KIM LIGHTING 7


Advanced Performance Features 

High Performance • Low Profile 

WARP9’s super low profile housing does not 

mean a compromise in illumination performance. 

In fact, an entire new series of reflector systems 

was specifically developed through a highly 

detailed computer study of efficiency and lamp 

output maximization. These new systems feature 

highly specular 95% reflective Alzak finishing, 

tooled and assembled by hand at Kim Lighting’s 

California facilities to maintain the highest quality 

and performance standards. Choose from IES 

Type II, III, IV, and V Sq distributions, rotatable for 

any application or distribution requirement. 

Full Cutoff: StarView Compliant 

Kim Lighting's StarView products meet IES 

and IDA full cutoff requirements for use where 

light pollution or light trespass may be a concern, 

and to promote the enjoyment of celestial 

visibility at night. 

WARP9 utilizes a horizontal lamp orientation 

with a flat glass lens to produce full cutoff with 

zero light above 90° horizontal. Therefore, all 

WARP9 fixtures are StarView compliant and 

are approved for full cutoff applications in 

any jurisdiction. 

WARP9 also offers a house-side shield option 

where light trespass and control of spill light 

onto adjacent property may be a concern. 

WP9L = 5K" 

WP9S = 4B" 

8 KIM LIGHTING


Four Distinct Light Distributions 

Site configuration determines the combination of 

light distributions required to efficiently illuminate 

desired areas. WARP9 is available in four highly 

efficient light patterns, combined with seven 

mounting arrangements and rotatable optics for 

incredible design versatility and flexibility. Contact 

Kim Lighting for free layout and application 

planning services, if needed. 

1A 2B 2L 3T 3Y 4C 1W 

Type II Type III Type IV Type V Sq 

KIM LIGHTING 9


Optical Design Features 

Advanced Heat Management 

WARP9’s die-cast housing is a homogeneous 

component in which every feature has a 

functional purpose. HID lamps produce significant 

heat, yet are operated by temperature sensitive 

electrical components. Because of its compact, 

low profile size, new methods of controlling heat 

were required for WARP9. A combination of 

cooling ribs, ventilation, and a solid barrier wall 

between the optical chamber and the ballast 

compartment are employed to control operating 

temperatures for maximum component life. 

Rotatable Optics 

All WARP9 reflectors are field rotatable in 90° 

increments. This allows design flexibility in 

producing very high illumination levels for special 

applications, or for maintaining a consistent fixture 

orientation throughout the site. Each reflector is 

labeled to show the orientation of the light 

pattern, and can be field adjusted after 

initial installation. 

For applications requiring high light levels, such as 

sports facilities, auto dealerships, or service 

stations, reflectors can be aimed in parallel to 

double illumination levels. 

10 KIM LIGHTING


Four rotatable reflector 

options featuring new 95% 

Alzak reflectivity 

Horizontal lamp orientation for 

uniformity and cutoff control 

One-piece silicone gasket 

with high memory retention 

Barrier wall completely 

separates optical chamber 

from electrical components 

Unique low profile 

frameless lens 

Totally sealed optical 

chamber stays clean for 

decades 

Multiple HID lamp options, 

electronic or magnetic 

ballasted versions 

Unique Frameless Lens 

WARP9 employs a unique frameless lens for 

several purposes. For improved camouflaging, the 

frameless lens lends to the sleek profile and 

reduced mass of the housing envelope, also 

reducing the amount of geometrical and straight 

lines that tend to attract the human eye. Second, 

the frameless lens allows for a consistent and 

positive gasket seal to completely isolate the 

optical chamber from moisture, air, and insect 

entry. Finally, fewer component pieces reduce 

overall fixture weight and improve allowable EPA. 

Multiple Lamp Options 

42W 

57W 

60W 

70W •/+ + • 

85W 

PMH MH HPS PL IF 

• 

• 

• 

• 

100W •/+ + • 

150W •/+ + • 

175W + 

200W •/+ 

250W •/+ + + 

320W •/+ 

350W •/+ 

400W •/+ + + 

PMH = Pulse Start Metal Halide 

MH = Metal Halide 

HPS = High Pressure Sodium 

PL = Compact Fluorescent 

IF = Induction Fluorescent 

WP9SE / WP9LE(electronic) = • 

WP9SM / WP9LM(magnetic) = + 

KIM LIGHTING 11


Mechanical Features 

• 

• 

Aluminum 

Titanated Zirconium 

Conversion Coating 

Powder Coat 

• 

New 

Stealth 

Gray TM Finish 

Diecast Aluminum Components 

Durable Powder Coat Finish 

WARP9’s housing and arm assembly are die-cast, low 

copper alloy (


Completely new field-rotatable reflector 

systems with 95% reflectivity 

Kim Lighting’s durable Super 

TGIC powder coat paint 

finish, featuring Stealth Gray 

Concealed die-cast 

no-tool latch allows easy 

access to optical chamber 

One-piece silicone 

gaskets assure positive seal 

after relamping 

Integrated cooling 

ribs for advanced 

heat management 

Die-cast aluminum 

arm attachment 

Die-cast aluminum housing 

Isolated wiring and electrical 

component chamber 

KIM LIGHTING 13


Installation & Maintenance Features 

Easy Installation and Set-Up 

No-Tool Maintenance 

The attachment of lighting fixtures to poles is often a 

neglected detail that ruins a clean design with boxy 

armatures and exposed nuts, bolts, or screws. WARP9’s 

arm connection naturally integrates and blends with the 

fixture head for a clean, strong appearance without 

exposed hardware or attachments. WARP9 also utilizes 

an internal mounting-bolt system concealed within the 

arm, fixture, and pole for maximum rigidity and 

assured coupling. 

Inside the pole top, a reinforcing plate receives the mounting 

bolts. A strain relief is provided on the reinforcing plate 

for securing the field wires. The cast-aluminum arm has 

concealed mounting bolts accessible through a flush cover 

that blends with the arm pre-assembled at Kim Lighting. 

The arm is configured to complement the fixture design 

and make the fixture-to-pole connection look natural, 

logical, and homogeneous. 

Ease of maintenance is a feature that distinguishes a 

lifetime product from an inferior substitution. WARP9 

utilizes modular construction for easy installation and 

maintenance, and to allow for upgrading as lamp 

technology advances. 

To reduce expensive lift-truck rental time, relamping can 

be quickly accomplished without tools. A single latch on 

the nose of the fixture opens the hinged frameless lens. If 

ballast replacement is required, the entire electrical 

module is accessed through a separate latched door on 

the underside of the fixture, and includes quick-disconnect 

plugs on all wiring. A spare electrical module can be 

quickly inserted to eliminate downtime, while the old 

module can be repaired and stored for future use. 

14 KIM LIGHTING


Proportion Guide 

Electronic ballast versions shown. 

KIM LIGHTING 15


Ordering Information 

1 Mounting: 

Ordering Example: 

For standard fixture and pole 

3Y configuration is available for 

round poles only. 

Mounting Fixture Electrical Module Finish Options Pole VSF Option 

2SB /WP9LE3/ 250PMH277 / SG-P/ A-25 / PRA20-4188SB / SG-P / VSF-2SB 

1 2 3 4 5-11 12 13 

See separate Kim Pole Catalog. 

Omit for 1W Wall Mount. 

Plan View: 

EPA WP9L: 0.95 1.9 1.47 2.4 2.4 2.7 n/a 

EPA WP9S: 0.52 1.04 0.82 1.3 1.3 1.5 n/a 

Cat. No.: 1SA 2SB 2SL 3ST 3SY 4SC 1SW 

Wall 

Mount 

2 Fixture: 

Cat. No. designates fixture and 

light distribution 

3 Electrical Module: 

PMH = Pulse Start 

Metal Halide 

MH = Metal Halide 

HPS = High Pressure Sodium 

PL 

= Compact Fluorescent 

IF = Induction Fluorescent 

See lamp and electrical data 

on pages 20-21 

Light Distribution: Type II Type III Type IV Type V 

Forward Throw 

Square 

Full Cutoff Full Cutoff Full Cutoff Full Cutoff 

Warp9 Small 

Electronic Ballast: WP9SE2 WP9SE3 WP9SE4 WP9SE5 

Warp9 Small WP9SM2 WP9SM3 WP9SM4 WP9SM5 

Magnetic Ballast: 

Warp9 Large 

Electronic Ballast: WP9LE2 WP9LE3 WP9LE4 WP9LE5 

Warp9 Large WP9LM2 WP9LM3 WP9LM4 WP9LM5 

Magnetic Ballast: 

Warp9 - Small / Electronic 

Pulse Start 

Metal Halide 

70PMH120 

70PMH208 

70PMH240 

70PMH277 

100PMH120 

100PMH208 

100PMH240 

100PMH277 

150PMH120 

150PMH208 

150PMH240 

150PMH277 

Compact 

Fluorescent 

42PL120 

42PL208 

42PL240 

42PL277 

57PL120 

57PL208 

57PL240 

57PL277 

Warp9 - Large / Electronic 

Pulse Start 

Metal Halide 

200PMH120 

200PMH208 

200PMH240 

200PMH277 

250PMH208 

250PMH240 

250PMH277 

320PMH208 

320PMH240 

320PMH277 

350PMH208 

350PMH240 

350PMH277 

400PMH208 

400PMH240 

400PMH277 

Induction 

Fluorescent* 

100IF120 150IF120 

100IF208 150IF208 

100IF240 150IF240 

100IF277 150IF277 

100IF347 150IF347 

100IF480 150IF480 

* Available in Type I I 

distribution only 

Lamp Lamp Line 

Watts Type Volts 

250 PMH 277 

Warp9 - Small / Magnetic 

Pulse Start 

Metal Halide 

70PMH120 150PMH120 

70PMH208 150PMH208 

70PMH240 150PMH240 

70PMH277 150PMH277 

70PMH347 150PMH347 

70PMH480 150PMH480 

100PMH120 

100PMH208 

100PMH240 

100PMH277 

100PMH347 

100PMH480 

High Pressure 

Sodium 

70HPS120 

70HPS208 

70HPS240 

70HPS277 

70HPS347 

70HPS480 

100HPS120 

100HPS208 

100HPS240 

100HPS277 

100HPS347 

100HPS480 

150HPS120 

150HPS208 

150HPS240 

150HPS277 

150HPS347 

150HPS480 

Metal Halide 

175MH120 

175MH208 

175MH240 

175MH277 

175MH347 

175MH480 

Warp9 - Large / Magnetic 

Pulse Start 

High Pressure 

Metal Halide 

Sodium 

200PMH120 350PMH120 150HPS120 

200PMH208 350PMH208 150HPS208 

200PMH240 350PMH240 150HPS240 

200PMH277 350PMH277 150HPS277 

200PMH347 350PMH347 150HPS347 

200PMH480 350PMH480 150HPS480 

250PMH120 400PMH120 250HPS120 

250PMH208 400PMH208 250HPS208 

250PMH240 400PMH240 250HPS240 

250PMH277 400PMH277 250HPS277 

250PMH347 400PMH347 250HPS347 

250PMH480 400PMH480 250HPS480 

320PMH120 

400HPS120 

320PMH208 

400HPS208 

320PMH240 

400HPS240 

320PMH277 

400HPS277 

320PMH347 

400HPS347 

320PMH480 

400HPS480 

Metal Halide 

175MH120 

175MH208 

175MH240 

175MH277 

175MH347 

175MH480 

250MH120 

250MH208 

250MH240 

250MH277 

250MH347 

250MH480 

400MH120 

400MH208 

400MH240 

400MH277 

400MH347 

400MH480 

16 KIM LIGHTING


4 Finish: 

Super TGIC powder coat 

paint over titanated zirconium 

conversion coating. 

(see page 12) 

Color: Black Dark Bronze Stealth Gray TM Platinum Silver White Custom Colors 

Cat. No.: BL-P DB-P SG-P PS-P WH-P CC-P 

Consult your Kim 

Lighting representative 

for custom colors. 

5 Wall Mounting: 

Cat. No.: 1W 

A cast-aluminum mounting plate is mounted to the wall with four bolts 

(by others). Fixture and arm are mounted to the cast aluminum cover 

plate before attaching to the wall mounting plate. The fixture-arm-cover 

plate assembly is hooked to the wall mounting plate and secured with 

stainless steel screws provided. Field splices are made at the opening 

in the cover plate. Cover is finished to match arm and fixture color. 

6 Optional Photocell 

Button 

Receptacle 

Cat. No.: A-25 

Receptacle 

A-30 - A-35 

Button 

Two types of photocell controls are available. A receptacle for a NEMA 

base photocell (by others) would be located above the electrical 

compartment. For all multiple-fixture pole mountings with two or three 

fixtures, one fixture has a receptacle to operate the others. Four fixtures 

(250 watt or less) also require one fixture with a receptacle. Four fixtures 

(400 watt) require two fixtures with receptacles. Also available is an internal 

photocell with a button sensor on the left side of the fixture. For multiplefixture 

pole mountings, one fixture has a photocell to operate the others. 

7 Optional SLX Lexan ® 

Non-Yellowing Lens: 

SLX Lexan Lens 

Cat. No.: SLX 

One-piece non-yellowing vacuum formed advanced polymer 

(SLX Lexan from GE Advanced Materials) enclosure covers standard 

tempered glass lens. 

CAUTION: Use only when vandalism is anticipated to be high. 

8 Optional Houseside 

Shield: 

HS for flat lens 

Cat. No.: HS 

Recommended for use with clear lamps only. Effectiveness is reduced 

for coated lamps. Not for use with Type V Sq light distributioons. 

9 Optional Neighbor 

Friendly Shield: 

Cat. No.: NFS 

(Type IV only) Stamped internal shield and blocking panels are used 

todirect and redirect lighting into a forward throw distribution. The 

amountof light directed and redirected toward the back of the luminaire 

isdramatically reduced to create extremely low glare behind the pole. 

Only available on the Type IV reflectors. 

10 Optional Tamper- 

Resistant Latch: 

Tamper-Resistant Latch 

Cat. No.: TL 

Standard die-cast latch is provided with a captive 10-32 stainless steel flat 

socket-head screw to prevent unauthorized opening. Required only for 

vandal protection in locations where fixtures can be reached by 

unauthorized persons. 

11 Optional Horizontal 

Slipfitter Mount: 

Slipfitter 

Cat. No.: HSF 

Replaces standard mounting arm with a slipfitter for mounting to a 

horizontal pole davit-arm with 2" pipe-size mounting end (2C" O.D.). 

Provides ±5° vertical fixture adjustment. 

12 Special Options for 

Street Lighting: 

Cat. No.: TB 

Terminal Block located inside the fixture electrical compartment. (For Large Only) 

13 Poles: 

14 Optional Vertical 

Slipfitter Mounts: 

See Kim Pole Catalog for a complete selection of square and round poles in aluminum or steel. 

Round 

Cat. No. Cat. No Mounting Configuration 

VSF-1SA SVSF-1SA 1SA - Single arm mount 

VSF-2SB SVSF-2SB 2SB - 2 at 180° 

VSF-2SL SVSF-2SL 2SL - 2 at 90° 

VSF-3ST SVSF-3ST 3ST - 3 at 90° 

VSF-3SY Square 

3SY - 3 at 120° 

VSF-4SC SVSF-4SC 4SC - 4 at 90° 

Allows standard fixture and arm 

to be mounted to poles having a 

2" pipe-size tenon (2C" O.D. x 4K" 

min. length). 

KIM LIGHTING 17


Luminaire Specifications 

Dimensions - Electronic Ballast 

WP9LE 

Large Electronic Ballast 

200 to 400 watt PMH 

Mogul Base Lamps 

100 and 150 watt IF 

EPA: .95 

Maximum weight: 

35 lb. electronic 

WP9SE 

Small Electronic Ballast 

42 to 150 watt 

PMH and PL 

Medium Base Lamps 

EPA: .52 


17 lb. electronic 

TOP 

TOP 

5K" 

(139.7 mm) 

35B" 

(892.2 mm) 

10M" 

(261.9 mm) 

4B" 

(104.7 mm) 

26I" 

(684.2 mm) 

8I" 

(227.0 mm) 

1I" 

(49.2 mm) 

FRONT 

10M" 

(261.9 mm) 

SIDE 

5I" 

(150.8 mm) 

1K" 

(38.1 mm) 

FRONT 

8I" 

(227.0 mm) 

SIDE 

5N" 

(141.3 mm) 

5B" 

(130.2 mm) 

4G" 

(112.7 mm) 

20" 

(508.0 mm) 

15" 

(381.0 mm) 

BOTTOM 

BOTTOM 

SPECIFICATIONS 

HOUSING: One-piece die-cast, low copper alloy (


Dimensions - Magnetic Ballast 

WP9LM 

Large Magnetic Ballast 

150 to 400 watt 

PMH, HPS and MH 

Mogul Base Lamps 

WP9SM 

Small Magnetic Ballast 

70 to 175 watt 

PMH, HPS and MH 

Medium Base Lamps 

EPA: .95 


41 lb. magnetic 

TOP 

EPA: .52 


21 lb. magnetic 

TOP 

5K" 

(139.7 mm) 

35B" 

(892.2 mm) 

10M" 

(261.9 mm) 

4B" 

(104.7 mm) 

26I" 

(684.2 mm) 

8I" 

(227.0 mm) 

1I" 

(49.2 mm) 

FRONT 

10M" 

(261.9 mm) 

SIDE 

5I" 

(150.8 mm) 

1K" 

(38.1 mm) 

FRONT 

8I" 

(227.0 mm) 

SIDE 

5N" 

(141.3 mm) 

5B" 

(130.2 mm) 

4G" 

(112.7 mm) 

20" 

(508.0 mm) 

15" 

(381.0 mm) 

BOTTOM 

BOTTOM 

KIM LIGHTING 19


Lamp Guide 

Lamp 

Watts 

Lamp 

Type 

System 

Watt 

Bulb 

Type 

Initial 

Lumens 

Life 

(Hours) 

PULSE START METAL HALIDE 

70 PMH 90 Clear, ED17, Med Base 6,200 16,000 M98 -30C HX-HPF 120 0.85 1.90 0.80 4 

Clear, T6, G12 Base 6,600 M143 208 0.52 1.00 0.50 3 

240 0.44 0.90 0.43 2 

277 0.39 0.80 0.39 2 

347 0.28 0.70 0.20 2 

480 0.23 0.50 0.26 2 

70 PMH 80 Clear, ED17, Med Base 6,200 16,000 M98 -30C Electronic 120 - - 0.67 4 

Clear, T6, G12 Base M143 208 - - 0.45 3 

M139 240 - - 0.38 2 

277 - - 0.30 2 


208 0.66 1.40 0.80 4 

240 0.58 1.15 0.65 3 

277 0.50 1.00 0.60 3 

347 0.40 1.00 0.40 2 

480 0.30 0.55 0.30 2 


M140 208 - - 0.70 4 

240 - - 0.60 3 

277 - - 0.40 3 


Clear, T6, G12 Base M142 208 1.00 2.10 1.30 5 

240 0.80 1.80 0.85 5 

277 0.70 1.58 0.77 4 

347 0.55 1.25 0.65 3 

480 0.42 0.81 0.45 3 


Clear, T6, G12 Base M142 208 - - 1.00 5 

240 - - 0.80 5 

277 - - 0.60 4 

200 PMH 240 Clear, T15, Mogul Base 19,000 15,000 M136 -30C Super 120 2.00 2.00 0.75 6 

CWA 208 1.20 1.20 0.40 4 

240 1.00 1.00 0.35 3 

277 0.85 0.85 0.30 3 

347 0.70 0.65 0.25 2 

480 0.50 0.50 0.18 2 

200 PMH 229 Clear, T15, Mogul Base 19,000 15,000 M136 -30C Electronic 120 - - 2.00 6 

208 - - 1.20 4 

240 - - 1.00 3 

277 - - 1.00 3 

250 PMH 295 Clear, BT28, Mogul Base 22,500 11,250 M138 -30C CWA 120 2.50 1.40 2.30 8 

M153 208 1.45 0.80 1.30 5 

240 1.25 0.70 1.15 5 

277 1.10 0.60 1.00 3 

347 0.95 0.75 0.45 3 

480 0.57 0.48 0.21 2 

250 PMH Clear, BT28, Mogul Base 22,500 11,250 M138 -30C Electronic 208 - - 1.36 5 

M153 240 - - 1.19 3 

277 - - 1.06 3 

320 PMH 368 Clear, BT28, Mogul Base 30,000 20,000 M132 -30C Super 120 3.25 2.30 1.80 8 

M154 CWA 208 1.90 1.35 1.05 6 

M170 240 1.65 1.15 0.90 5 

277 1.40 1.00 0.80 3 

347 1.10 0.80 0.70 3 

480 0.80 0.60 0.45 5 


M154 240 - - 1.49 6 

M170 277 - - 1.32 5 


M171 CWA 208 2.00 1.30 1.30 7 

240 1.70 1.10 1.10 5 

277 1.50 1.00 1.00 5 

347 1.20 0.80 0.85 3 

480 0.85 0.60 0.60 3 


M171 240 - - 1.59 7 

277 - - 1.41 5 


M155 CWA 208 2.30 1.75 2.00 7 

M172 240 2.00 1.50 1.75 5 

277 1.75 1.30 1.50 5 

347 1.35 0.75 1.10 4 

480 1.00 0.60 0.75 3 


M155 240 - - 1.81 7 

M172 277 - - 1.59 5 

ANSI 

Code 

Starting 

Temp 

Circuit 

Type 

Voltage 

Operating 

Amps. 

Open 

Circuit 

Amps. 

Starting 

Amps. 

Min. Fuse 

Amps. 

20 KIM LIGHTING


Lamp 

Watts 

Lamp 

Type 

System 

Watt 

Bulb 

Type 

Initial 

Lumens 

Life 

(Hours) 

METAL HALIDE 

175 MH 210 Clear, ED17, Med Base 14,400 7,000 M57 -30C CWA 120 1.80 1.80 1.30 5 

208 1.04 1.04 0.75 3 

240 0.90 0.90 0.65 3 

277 0.80 0.80 0.55 2 

347 0.65 0.65 0.50 2 

480 0.45 0.45 0.35 2 

250 MH 295 Clear, BT28, Mogul Base 23,000 7,000 M58 -30C CWA 120 2.60 2.60 1.00 8 

208 1.50 1.50 0.60 5 

240 1.30 1.30 0.50 5 

277 1.10 1.10 0.45 3 

347 0.85 1.05 0.35 3 

480 0.65 0.65 0.30 2 

400 MH 458 Clear, BT28, Mogul Base 40,000 15,000 M59 -30C CWA 120 4.00 3.20 2.50 10 

208 2.30 1.80 1.40 7 

240 2.00 1.60 1.20 5 

277 1.70 1.50 1.00 5 

347 1.35 1.35 0.80 4 

480 1.00 0.75 0.90 3 

HIGH PRESSURE SODIUM 

70 HPS 91 Clear, ED17, Med Base 6,300 24,000 S62 -40C HX-HPF 120 

208 

0.81 

0.47 

1.45 

0.85 

0.75 

0.45 

6 

4 

240 0.4 0.75 0.37 3 

277 0.35 0.65 0.35 3 

347 0.3 0.55 0.3 2 

480 0.21 0.36 0.21 2 

100 HPS 130 Clear, ED17, Med Base 9,500 24,000 S54 -40C HX-HPF 120 1.15 2.20 1.30 7 

208 0.67 1.25 0.75 5 

240 0.58 1.10 0.65 3 

277 0.50 0.85 0.60 3 

347 0.39 0.70 0.45 3 

480 0.22 0.34 0.21 3 

150 HPS 188 Clear, ED17, Med Base 16,000 24,000 S55 -40C HX-HPF 120 1.65 2.80 2.00 10 

208 0.95 1.60 1.15 5 

240 0.83 1.40 1.00 5 

277 0.72 1.25 0.85 4 

347 0.56 0.92 0.52 3 

480 0.42 0.70 0.50 2 

250 HPS 295 Clear, E18, Mogul Base 29,000 24,000 S50 -40C CWA 120 2.50 1.70 1.65 7 

208 1.50 1.00 0.95 4 

240 1.30 0.85 0.80 4 

277 1.10 0.75 0.70 3 

347 0.93 0.70 0.60 2 

480 0.63 0.45 0.40 2 

400 HPS 464 Clear, E18, Mogul Base 51,000 24,000 S51 -40C CWA 120 3.80 2.00 3.30 10 

208 2.20 1.20 1.80 6 

240 1.90 0.95 1.50 5 

277 1.70 0.85 1.40 5 

347 1.32 0.70 1.00 5 

480 0.97 0.55 0.75 3 

COMPACT FLUORESCENT 

42 PL 46 Coated, GX24q-4 Base 3,200 12,000 N/A -18C Electronic 120 - - 0.39 2 

208 - - 0.23 2 

240 - - 0.20 2 

277 - - 0.17 2 

57 PL 59 Coated, GX24q-5 Base 4,300 12,000 N/A -10C Electronic 120 - - 0.80 2 

208 - - 0.40 2 

240 - - 0.27 2 

277 - - 0.21 2 

INDUCTION FLUORESCENT 

Max. Fuse Amps. 

100 IF 120 - - 0.88 3 

208 - - 0.66 2 

240 - - 0.37 2 

277 - - 0.29 2 

150 IF 120 - - 1.34 4 

208 - - 1.28 4 

240 - - 0.58 2 

277 - - 0.54 2 

All Initial Lumen values shown are approximate and may vary from one manufacturer to another. Consult lamp manufacturer’s data for exact lumen and life data. 

WARNING: All fixtures must be grounded in accordance with local codes or the National Electrical Code. Failure to do so may result in serious personal injury. 

Lamps by others. 

ANSI 

Code 

Starting 

Temp 

Circuit 

Type 

Voltage 

Operating 

Amps. 

Open 

Circuit 

Amps. 

Starting 

Amps. 

Min. Fuse 

Amps. 

KIM LIGHTING 21

TM 

www.kimlighting.com 

Because of a continuing product 

improvement program, 

Kim Lighting reserves the 

right to change 

specifications without notice. 

How may we serve you better? 

Let us know by visiting our web site 

at: www.kimlighting.com 

Hubbell 

Lighting, Inc.

WARP9 - Kim Lighting

Create successful ePaper yourself

Delete template?

Save as template?