Catalog 604: Pneumatic Products - Wilkerson Corporation

More documents

Recommendations

Info

Catalog 604 Programming Symbols Legend Pressure Sensors MPS-32 2-Color Panel Mount Output 1 Output 2 Output 3 Output 4 Output Normally Closed (Passing) Output Normally Open (Non-Passing) Pressure Units (Pascal). Negative Units for Vacuum Sensors Pressure Units (Bar). Negative Units for Vacuum Sensors Pressure Units (mm.Hg). Negative Units for Vacuum Sensors Pressure Units (in.Hg). Negative Units for Vacuum Sensors Pressure Units (kgf/cm2). Negative Units for Vacuum Sensors Pressure Units (PSI) Easy Mode. Sensor will only allow changes to set points Off, or Energy Saving Display; reduces current consumption of Sensor On Hysteresis Mode. Select Hysteresis Set Point and Hysteresis Range Windows Comparative Mode Select High and Low Set Point Hysteresis Mode Set Point. Output 1 Hysteresis Mode Set Point. Output 2 Hysteresis Mode. Hysteresis Range Output 1 Hysteresis Mode. Hysteresis Range Output 2 Windows Comparative Mode Low Set Point Output 1 Windows Comparative Mode High Set Point Output 1 Windows Comparative Mode Low Set Point Output 2 Windows Comparative Mode High Set Point Output 2 Automatic Teach Mode. Automatically sets Outputs 1 and 2 while cycling system. Output 1 set to Hysteresis Mode, Output 2 set to Window Comparative Mode Auto Surveillance Mode On/Off. Set after Automatic Teach Auto Surveillance based on cycles times. Provides output if Peak Value is not obtained in a specified number of cycles. (1-100) Display Refresh Setting. Display updates from .1 to 1 sec. .3 sec factory set. Does not affect Sensor Response Time Output Response Time. Multiples the sensor response time. Increases sensor response time. (Anti-chatter Mode) Zero Reset Pressure Value Display Mode. Displays Pressure for a specific time period and then updates for next time period Time Range for Pressure Value Display Mode Value Setting for Pressure Value Display Mode Display Peak Value over selected time range Display Bottom Value over selected time range Display Difference over selected time range Display Function Mode. On/Off Display Function. Selects display types. Display blinks pressure when Output 1 is Passing Normal when Output 1 is Non-Passing Display blinks pressure when Output 2 is Passing Normal when Output 2 is Non-Passing Display shows pressure when Output 1 is Passing Display shows special screen when Non-Passing Display shows pressure when Output 2 is Passing Display shows special screen when Non-Passing Select Switch Output setting for MPS-31 Color Setting for MPS-31 MPS-4, Port Reference Selection MPS-4, Display change of B port to A port static MPS-4, Display change of A port to B port static MPS-4, Display change of A port to change of B port MPS-7, Pressure Range Selection Vacuum MPS-7, Pressure Range Selection Low Pressure MPS-7, Pressure Range Selection Positive Pressure MPS-7, Pressure Range Selection Compound Pressure MPS-7, Energy Savings Mode, reduces current consumption MPS-7, Peak Surveillance Digital Input Sensors Only. Digital Input Mode for remote Zero reset of sensors Digital Input Digital Channel MPS-7 Scan Mode. Sensor scans and displays each channel for 3 sec. Locked. Sensor programs cannot be changed Unlocked. Sensor programs can be changed Sets Sensors reference point to current atmospheric conditions 24 Pneumatic Division Richland, Michigan www.wilkersoncorp.com
Catalog 604 Safety Guide Precision Regulators Safety Guide For Selecting And Using Pneumatic Division Products And Related Accessories ! WARNING: FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF PNEUMATIC DIVISION PRODUCTS, ASSEMBLIES OR RELATED ITEMS (“PRODUCTS”) CAN CAUSE DEATH, PERSONAL INJURY, AND PROPERTY DAMAGE. POSSIBLE CONSEQUENCES OF FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THESE PRODUCTS INCLUDE BUT ARE NOT LIMITED TO: • Unintended or mistimed cycling or motion of machine members or failure to cycle • Work pieces or component parts being thrown off at high speeds. • Failure of a device to function properly for example, failure to clamp or unclamp an associated item or device. • Explosion • Suddenly moving or falling objects. • Release of toxic or otherwise injurious liquids or gasses. Before selecting or using any of these Products, it is important that you read and follow the instructions below. 1. GENERAL INSTRUCTIONS 1.1. Scope: This safety guide is designed to cover general guidelines on the installation, use, and maintenance of Pneumatic Division Valves, FRLs (Filters pressure Regulators and Lubricators), Vacuum products and related accessory components. 1.2. Fail-Safe: Valves, FRLs, Vacuum products and their related components can and do fail without warning for many reasons. Design all systems and equipment in a fail-safe mode, so that failure of associated valves, FRLs or Vacuum products will not endanger persons or property. 1.3. Distribution: Provide a copy of this safety guide to each person that is responsible for selection, installation, or use of Valves, FRLs or Vacuum products. Do not select, or use Wilkerson valves, FRLs or vacuum products without thoroughly reading and understanding this safety guide as well as the specific Wilkerson publications for the products considered or selected. 1.4. User Responsibility: Due to the wide variety of operating conditions and applications for valves, FRLs, and vacuum products Wilkerson and its distributors do not represent or warrant that any particular valve, FRL or vacuum product is suitable for any specific end use system. This safety guide does not analyze all technical parameters that must be considered in selecting a product. The user, through its own analysis and testing, is solely responsible for: • Making the final selection of the appropriate valve, FRL, Vacuum component, or accessory. • Assuring that all user’s performance, endurance, maintenance, safety, and warning requirements are met and that the application presents no health or safety hazards. • Complying with all existing warning labels and / or providing all appropriate health and safety warnings on the equipment on which the valves, FRLs or Vacuum products are used; and, • Assuring compliance with all applicable government and industry standards. 1.5. Safety Devices: Safety devices should not be removed, or defeated. 1.6. Warning Labels: Warning labels should not be removed, painted over or otherwise obscured. 1.7. Additional Questions: Call the appropriate Wilkerson technical service department if you have any questions or require any additional information. See the Wilkerson publication for the product being considered or used, or call 269-629-2550, or go to www.wilkersoncorp.com, for telephone numbers of the appropriate technical service department. 2. PRODUCT SELECTION INSTRUCTIONS 2.1. Flow Rate: The flow rate requirements of a system are frequently the primary consideration when designing any pneumatic system. System components need to be able to provide adequate flow and pressure for the desired application. 2.2. Pressure Rating: Never exceed the rated pressure of a product. Consult product labeling, Pneumatic Division catalogs or the instruction sheets supplied for maximum pressure ratings. 2.3. Temperature Rating: Never exceed the temperature rating of a product. Excessive heat can shorten the life expectancy of a product and result in complete product failure. 2.4. Environment: Many environmental conditions can affect the integrity and suitability of a product for a given application. Pneumatic Division products are designed for use in general purpose industrial applications. If these products are to be used in unusual circumstances such as direct sunlight and/or corrosive or caustic environments, such use can shorten the useful life and lead to premature failure of a product. 2.5. Lubrication and Compressor Carryover: Some modern synthetic oils can and will attack nitrile seals. If there is any possibility of synthetic oils or greases migrating into the pneumatic components check for compatibility with the seal materials used. Consult the factory or product literature for materials of construction. 2.6. Polycarbonate Bowls and Sight Glasses: To avoid potential polycarbonate bowl failures: • Do not locate polycarbonate bowls or sight glasses in areas where they could be subject to direct sunlight, impact blow, or temperatures outside of the rated range. • Do not expose or clean polycarbonate bowls with detergents, chlorinated hydro-carbons, keytones, esters or certain alcohols. • Do not use polycarbonate bowls or sight glasses in air systems where compressors are lubricated with fire resistant fluids such as phosphate ester and di-ester lubricants. 26 Pneumatic Division Richland, Michigan www.wilkersoncorp.com
Page 1 and 2: Pneumatic Products Precision Regula
Page 3 and 4: Catalog 604 Table of Contents Preci
Page 5 and 6: Catalog 604 Application Chart Preci
Page 7 and 8: Catalog 604 Technical Specification
Page 13 and 14: Catalog 604 WRA171 Series WRA171 Se
Page 15 and 16: Catalog 604 WEA632 Series WEA632 Se
Page 17 and 18: Catalog 604 WBA208 Series WBA208 Se
Page 19 and 20: Catalog 604 WBA45 Series WBA45 Seri
Page 21 and 22: Catalog 604 Ordering Information Sp
Page 23 and 24: Catalog 604 Dimensions Pressure Sen
Page 25: Catalog 604 Accessories Pressure Se
Page 29 and 30: Catalog 604 Offer of Sale Precision

Catalog 604: Pneumatic Products - Wilkerson Corporation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?