the tsudakoma dual lead gearing system - Compumachine

More documents

Recommendations

Info

General Information NOTES: 1. Supply of Lubricant Before using your rotary table, recommended lubricant must be supplied as described in the instruction manual. Periodic replacement of lubricant is also required. 2. Supply of Hydraulic or Pneumatic Pressure for Table Clamping Rotary table clamping is activated either by hydraulic or pneumatic pressure depending on the model or specification of the rotary table. Be sure to supply air or hydraulic fluid at the required pressure. 3. Supply of Pneumatic Pressure for Air Purging Depending on environmental conditions, condensation may occur inside the motor cover. To eliminate condensation, air purge the motor cover. Make sure the exhaust port is clear. Air supply and hydraulic fluid must be available at the required pressure. Air supply Filter Regulator Hydraulic pressure for clamping Air exhaust Air exhaust Air exhaust (rotary table with pneumatic clamping) (rotary table with hydraulic clamping) (rotary table with air hydraulic booster unit) 4. NC Control for Table Clamping The recommended flow charts are shown on Page 75. 5. Misc. 1) Specifications, drawings, and photographs in this catalog are subject to change for improvement without notice. 2) Some of the products listed in this catalog are designated as strategic materials by the Foreign Exchange and Foreign Trade Control Law in Japan. Those who want to import them should have an approval based on that law from the Japanese government. CE CONFORMING ROTARY TABLES In addition to standard rotary tables, Tsudakoma manufactures CE conforming rotary tables. Specifications for CE conformity are available for all Tsudakoma rotary tables. Specifications for CE Conformity 1. All the electric components used confrom to European Safety Regulations. 2. Enclosure protection classification for electric components: greater than IP54 3. Conformity standards: • EC Machinery Directive 98/37/EC EN292-1,292-2 EN60204-1 • EMC Directive 89/336/EEC, 92/31/EEC EN50081-2 EN50082-2 86 www.komaprecision.com • info@komaprecision.com
TSUDAKOMA CORP. Nonoichi-machi, Ishikawa, 921-8529 Japan Phone: (076) 294-5111 Fax: (076) 294-5157 www.tsudakoma.co.jp kexport@tsudakoma.co.jp KOMA PRECISION, INC. 20 Thompson Road, East Windsor, CT 06088 Phone: 800-249-KOMA Fax: 860-623-4132 www.komaprecision.com info@komaprecision.com KOMA PRECISION, INC. IS THE SOLE NORTH AMERICAN IMPORTER OF TSUDAKOMA ROTARY TABLES
Page 3 and 4:
PRODUCTIVITY INNOVATION Tsudakoma r
Page 5 and 6:
TSUDAKOMA: PRECISION PERFORMANCE PR
Page 7 and 8:
Table Overview RZ-SERIES INDEXERS T
Page 9 and 10:
Contents THNC-SERIES TILTING TABLES
Page 11 and 12:
Dimensions RN-100R Dimensions = mm
Page 13 and 14:
Single Axis Rotary Tables Dimension
Page 15 and 16:
Page 17 and 18:
Dimensions RNCK-631 Dimensions = mm
Page 19 and 20:
Dimensions RNCM-251R Dimensions = m
Page 21 and 22:
Dimensions RBA-250R Dimensions = mm
Page 23 and 24:
Page 25 and 26:
Dimensions RTV-304,AA Dimensions =
Page 27 and 28:
Page 29 and 30:
Dimensions RT-147 Dimensions = mm S
Page 31 and 32:
Dimensions RNC-801L Dimensions = mm
Page 33 and 34:
Dimensions RN-100R-2,3,4 Single Axi
Page 35 and 36: Single Axis Indexers Dimensions RZ-
Page 37 and 38: Tilting Rotary Tables Dimensions TN
Page 39 and 40: Dimensions TTNC-451 Dimensions = mm
Page 41 and 42: Dimensions TTNC-102-2 Multi-Spindle
Page 43 and 44: Tilting Rotary Tables Dimensions Di
Page 45 and 46: Dimensions TRNC-151S Dimensions = m
Page 47 and 48: Dimensions THNC-251 Dimensions = mm
Page 49 and 50: Dimensions RC-200 Special Integrate
Page 51 and 52: Specialty Rotary Tables RNCV-401L-3
Page 53 and 54: Specialty Rotary Tables RTT-101,AA
Page 55 and 56: Single Axis NC Controllers TPC-Jr F
Page 57 and 58: Single Axis NC Controllers RN-100,
Page 59 and 60: Single Axis NC Controllers TPC CONT
Page 61 and 62: Single Axis NC Controllers TPC CONT
Page 63 and 64: Single Axis NC Controllers TPC3 WIR
Page 65 and 66: I Accessories CHUCKS POWER CHUCKS P
Page 67 and 68: Accessories MANUAL TAILSTOCK DIMENS
Page 69 and 70: Options HIGH RESOLUTION ENCODERS &
Page 71 and 72: Options PULL STUD DEVICES A pull st
Page 73 and 74: Options 5C COLLETS 5C collets are a
Page 75 and 76: Technical Information SERVO MOTORS
Page 77 and 78: Technical Information WORKPIECE MOU
Page 79 and 80: General Information ROTARY TABLE SE
Page 81 and 82: General Information INSPECTION STAN
Page 83 and 84: General Information INSPECTION STAN
Page 85: General Information TSUDAKOMA FACIL
show all

the tsudakoma dual lead gearing system - Compumachine

Create successful ePaper yourself

Delete template?

Save as template?