TUR - A - Inserts.cdr - Canela Tools

More documents

Recommendations

Info

Inserts selection Inserts Basic geometries (Non ferrous materials) Basic geometries (Heat resistant alloys) 1 - Select geometry ..NGP -CFM ..NGP ..NMX ..NGP ..NMX Finishing Medium machining Roughing Ap mm 9 -AL 4 3 2 1 ..NMX -CFM 0.5 ..NGP Positive inserts F mm/r 0.05 0.1 0.3 0.5 0.8 2 - Select grade Cutting condition Finishing Medium machining Roughing Interrupted cut KM15 - TIN16 - TIN17 - ZR10 NC25 - TIN17 - ZR10 NC25 - TIN17 - ZR10 Inconsistent cut KM15 - TIN16 - TIN17 - ZR10 NC25 - TIN17 - ZR10 NC25 - TIN17 - ZR10 Consistent cut KM15 - TIN16 - TIN17 - ZR10 NC25 - TIN17 - ZR10 NC25 - TIN17 - ZR10 3 - Select cutting speed Proceed to page B.77 for cutting data 1 - Select geometry ..NGP -CM -CS ..NGP -CS Finishing Medium machining Roughing Ap mm 6 4 3 2 1 0.5 2 - Select grade Cutting condition Interrupted cut Inconsistent cut Consistent cut 3 - Select cutting speed -CM -CS ..NGP F mm/r 0.05 0.1 0.3 0.5 0.7 Finishing Medium machining Roughing TIN17 TIN17 TIN17 TIN17 - TIN32 - TIN35 TIN17 - TIN32 - TIN35 TIN17 - TIN32 - TIN35 TIN35 TIN35 TIN35 -AL / -AP Aluminium wheel turning General turning Inserts Parting and Tooling Brazed tools Cartridges Drills Threading grooving Ceramic tools Automatic lathes Proceed to page B.77 for cutting data CANELA A.13
Inserts For more information see page: Grades: A.02 Geometries: A.06 Code Key: A.14 ISO inserts: A.16 Ceramic inserts: F.04 Parting and grooving inserts: G.02 Threading inserts: H.03 ISO Code Key Inserts Insert shape Clearance angle Tolerances Form of top surface 35° V 3° A 0,025 0,005 0,025 A N 55° D 5° B 0,013 0,005 0,025 F R 75° E 7° C 0,025 0,013 0,025 C F 80° 86° 55° 82° 85° 90° 108° 120° 135° - 90° C M K B A L P H O R S 15° 20° 25° 30° 0° 11° D E F G N P Clearance angles not included with in the standard for which particular information is necessary. 0,013 0,025 0,025 0,05-0,15 0,05-0,15 0,05-0,15 0,013 0,025 0,025 0,005 0,013 0,025 0,025 0,025 0,13 0,025 0,025 0,025 0,05-0,15 0,08-0,20 0,13 0,05-0,15 0,08-0,20 0,025 0,08-0,25 0,13-0,38 0,13 d m s s m H E G J K L M N U A M G W T Q U B H C 60° 80° T W d d Special version J X C N M G A F C H E G J K L M N U 0,0010 0,0005 0,0010 0,0005 0,0010 0,0010 0,002 to 0,006* 0,002 to 0,006* 0,002 to 0,006* 0,002 to 0,006* 0,002 to 0,006* 0,003 to 0,010* 0,0002 0,0002 0,0005 0,0005 0,0010 0,0010 0,0002 0,0005 0,0010 0,003 to 0,008* 0,003 to 0,008* 0,001 0,001 0,001 0,001 0,001 0,005 0,001 0,001 0,001 0,005 0,001 0,005 to 0,015* 0,005 d m s N / R / F A / M / G X IK > 1/4" E D X IK < 1/4" s m d d Tolerance (inches) * Depends on insert size Symbols as above Changes at inscribed circle IK < 1/4" Form of top surface A.14 www.canelatools.com
Page 1 and 2: Inserts www.canelatools.com
Page 3 and 4: Inserts For more information see pa
Page 13: Inserts For more information see pa
Page 19 and 20: For more information see page: Inse

TUR - A - Inserts.cdr - Canela Tools

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?