Attachment1 - Kudzu

More documents

Recommendations

Info

8801 SE Electrified Panic Bar Dummy Panic Bar 8099M1-Single Switch 8099M2-Dual Switch $226.20 ea. $269.12 ea. For remote control access or access control with an Adams Rite 8000 Series exit device. A 24 volt motor enclosed in pushbar retracts latch mechanism of exit device. Motor draws only 300 milliamps while operating and offers enough torque to overcome most door load situations. The motor draws current only when actually operating so electrical dogging can be achieved with no current draw other than that in the unlocking cycle. Operation is with simple push button, card reader, key pad or other switch. Switch can be momentary, allowing automatic relocking of device or “maintained”, to allow electrical dogging.Motor operation has no effect on mechanical exit function of device Motorized devices can require 1 to 4 seconds for the complete unlocking cycle. Requires a minimum of 4 wires available at door for installation. Ideal for electrical dogging or low frequency access control. Specify by adding “SE” after exit device model number. EXAMPLE: 8611SE Exit Device Outside trims Features: $537.08 ea. Electric latch retraction ♦ All models fit all Adams Rite Exit Device types Dummy pushbar with no latch mechanism but has switch activation, single or dual switch. Most common application is in conjunction with a maglock where bar is pushed to turn off magnet and allow exit from building. Dual switch version allows redundancy where required by code or the operation of a signal device along with maglock. Specify door type(Aluminum or Wood) and width when ordering. Available in all exit device finishes. The 8099 is also available as a non-operating dummy for doors not requiring an exit device but where matching trim is desired. Specify door type, opening width and type of exit device to be matched. 8066 3083 ♦ Models 3083 and 8066 feature an innovative clutch that protects locked lever against upward or downward pull ♦ All lever models meet ADA guidelines and California Title 19 ♦ All models ANSI/BHMA Grade 1 Exit Device Cylinder Hole 1 SVR 3 Mortise 5 Inset CVR 3 with cylinder hole 6 CVR 7 Rim 9 None 9 without cylinder hole 3081-33-US3 Escutcheon-8650 Required to mount any make standard Mortise cylinder, with MS cam, on the outside of door. Also required when specifying CVR devices with a cylinder. Specify finish being matched when ordering $32.40 ea. Exit Device 00 Mortise or CVR 01 Rim or SVR Finish $134.40 ea. $234.00 ea. CVR is Concealed Vertical Rod SVR is Surface Vertical Rod Door Handle 8066-01-08-US3 07 All Non-rated CVR, SVR, LHR Rim, LHR Mortise 08 All Non-rated RHR Rim, LHR Mortise 628 Satin Aluminum US9 Bright Bronze 313 Bronze Anodized US10 Satin Bronze 335 Black Anodized 10B “Oil-Rubbed” Bronze US3 Bright Brass US32 Satin Stainless US4 Satin Brass 41
4418A Installation Kit $288.36 ea. For locksmiths or others who regularly install locks and latches in narrow stile aluminum and glass doors, Adams Rite provides this handy kit, complete with sturdy metal tool box. The basis of the Installation Kit is the mounting bridge with the positioning tool used to install it. The bridge is screwed into place, spanning the hollow door stile to provide a sturdy mounting surface for the lock, without the need to drill and tap the glass channel. The Kit contains enough bridges, resilient washers and screws for 25 installations. It also includes a special 1-11/32” hole saw and hardened steel pilot plug for quick and perfectly aligned installation of MS4043 cylinder guards. Two cylinder guards, a spare hole-saw blade, armored strike, adhesive templates and miscellaneous spare parts are also furnished. Instruction Manual Faceplate Screws 4085 Lower Guide Cylinder Set Screws Cylinder Hole Saw Lock Mounting Templates MS4043 Cylinder Guards Spare Hole Saw Blade 4085 Header Strikes Mounting Screws Mounting Bridges for 25 Lock Installations: Rubber Washers 12 Radius(4104-01) 3 Flat(4104-02) MS4002-012 Armored Strike 10 Bevel(4104-03&-04) 4603 Rectifier Converts low voltage AC current to DC of same voltage. Installs in low voltage line between transformer and strike. Full wave bridge type. Rated 2 amps.(200 PIV). 4605 Wire-in Transformer $9.60 ea. $42.00 ea. Converts 120VAC to 24VAC. Rated 40 Volt-amp output assures plenty of power for strike release. Patented mounting bracket fits in knockout hole of standard electrical junction boxes. 42 4104 Radius Mounting Bridge $3.36 ea. Method “A” Method “A” spans the stile with a steel bridge at top and bottom of the lock. A simple handle(Adams Rite Installation Tool 4075) is used to position the bridge accurately in the stile while its two screws are tightened to form a “web” in the door. Resilient washers allow for minor adjustment to fit the lock flush in the door.
Page 1 and 2: ADAMS RITE MS 1850S DEADLOCK Alumin
Page 3 and 4: MS1850S-050 HOOKLOCK FUNCTION The M
Page 5 and 6: MS1860 Two-Point Deadbolt A/R MS186
Page 7 and 8: 1870 Cylinder-Operated Flushbolt 18
Page 9 and 10: 4015 Threshold Bolt A/R 4015 18 Con
Page 11 and 12: 4710 Deadlatch 7/8” B/S Alum. $72
Page 13 and 14: Function For hollow metal or wood d
Page 15 and 16: 4560 Deadlatch Handle $35.72 ea. 45
Page 17 and 18: 4501, 4502 Deadlatch Strikes 4501-0
Page 19 and 20: MS1847 Deadlock or Latch Face Recta
Page 21 and 22: 1000 Turn Series A/R 1000-01 A/R 10
Page 23 and 24: 7130 Flat Faceplate for Aluminum Ja
Page 25 and 26: 71R1 Series 7900 Series Function 36
Page 27 and 28: $392.04 ea. Series 3300 Fire Rated
Page 29: 3700 Fire Rated Rim Mounted Exit De

Attachment1 - Kudzu

Create successful ePaper yourself

Delete template?

Save as template?