1/10 Comp Crawler Race Roller Manual - Team Losi Racing
1/10 Comp Crawler Race Roller Manual - Team Losi Racing
1/10 Comp Crawler Race Roller Manual - Team Losi Racing
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
q<br />
STEP D-03<br />
Step D<br />
Outer Transmission Assembly<br />
A3166<br />
Idler Gear<br />
A3167<br />
Idler Shaft<br />
A6947<br />
x2<br />
5x11x4mm<br />
A6221<br />
x3<br />
4-40” x 5/8”<br />
A3170<br />
Slipper Gear<br />
A3171<br />
Slipper Pad<br />
A6308<br />
x1<br />
L 4-40 x 1/4”<br />
A3165<br />
Outer Trans Case<br />
A3170<br />
Slipper Spacer<br />
A3170<br />
Slipper Plate<br />
q STEP D-04 “DIG” Servo Installation<br />
• To take advantage of the <strong>Comp</strong> <strong>Crawler</strong>s<br />
2mm<br />
“front & rear” dig setup, a Radio System<br />
such as the Spektrum DX3R with a 3-position<br />
Aux channel is required. A 2-position<br />
Aux channel can be used as well, however<br />
only “front” dig can be used.<br />
• If you will not be using the optional Dig<br />
system, remove the small tie rod attached<br />
to the shift horn.<br />
• A <strong>Losi</strong> MSX12 (LOSB0822) Mini Digital<br />
6mm<br />
Servo is required to use the dig options.<br />
Front “Dig”<br />
• Caution: When setting up the <strong>Comp</strong><br />
<strong>Crawler</strong> with dig, it is important to set<br />
your AUX channels Travel/EPA (End<br />
Point Adjustment) to “Zero” in any<br />
direction. If this is not done, servo failure<br />
can occur.<br />
• Once the proper dig arm is attached to your<br />
servo (<strong>Losi</strong>, JR, Airtronics & KO Propo<br />
23T, Hitec 24T, Futaba 25T) and is centered,<br />
you can now adjust the Travel/EPA<br />
5.5mm<br />
settings for each direction. While adjusting<br />
the travel, note that once the Dig shaft<br />
stops moving, you can stop adjustment.<br />
If any more travel is set, the Mini Servo<br />
could encounter damage.<br />
Full Time<br />
4wd<br />
Rear “DIG”<br />
A4038<br />
x1<br />
4-40” x 5/8”<br />
A6001<br />
x2<br />
3/16”<br />
A4038<br />
Rod End<br />
A4038<br />
Shift Horn<br />
A6306<br />
x1<br />
L 4-40 x 3/16”<br />
A4038<br />
Dig Arm<br />
A6350<br />
x6<br />
1/8” x .020”<br />
A6229<br />
x6<br />
4-40” x 3/8”<br />
A6308<br />
x2<br />
L 4-40 x 1/4”<br />
<strong>10</strong>