DEVRAN 124 Chemical Resistant Secondary Containment Coating

®
DEVRAN 124
Chemical Resistant Secondary
Containment Coating
Cat. # 124B2216/124C0910
Generic: Two-component Novolac Epoxy Coating.
General Description: 100% solids Novolac epoxy coating with
excellent chemical resistance properties which may be applied on
both vertical and horizontal surfaces.
Typical Uses: Excellent secondary containment coating with good
chemical resistance. Also recommended for use on concrete floors
in a wide range of facilities where abrasion resistance is required.
May be applied to vertical surfaces up to 12.0 mils dry in one
application. May also be applied to steel surfaces.
Special Qualifications: See Chemical Resistance Guide for Tank
Lining and Secondary Containment.
Advantages:
• High chemical resistance
• High impact and abrasion resistance
• Low odor application
• Resistant to 98% sulfuric acid and 37% hydrochloric acid for
splash, spills and secondary containment
• Resistant to dilute organic acids, alkalies and organic solvents in
splash spillage conditions
• Excellent secondary containment lining
• Can be applied up to 1/2'' thick on horizontal surface
• May be applied up to 12 mils on vertical surfaces
• Can be used as a broadcast, slurry or troweled system
Color: Gray
Finish: High Gloss
Weight/Gallon: 11.5 lbs./gal. (1.38 kg/L)
VOC (EPA 24): 0.29 lbs./gal. (35 g/L)
Solids By Volume: 100%
Theoretical Coverage at 1.0 Mil Dry: 1604 sq. ft./gal. (39.3 m 2 /L)
Recommended Film Thickness: 20.0-25.0 mils (500-
650 microns) dry –20.0-25.0 mils (500-650 microns) wet
Systems: Please consult the appropriate system guide, the particular
job specification or your ICI Paints Representative for proper systems
using this product. Systems must be selected considering the
particular environment involved.
Minimum Dry Time (ASTM D 1640): At 20.0 mils (500 microns) DFT
Substrate
Temperature 50°F (16°C) 70°F (21°C) 90°F (32°C)
Min. Recoat 25 Hours 6-7 Hours 4-5 Hours
Maximum
Self Recoat 48 Hours 24 Hours 8-9 Hours
Ventilation, film thickness, humidity, thinning, and other factors can
influence the rate of dry.
Warning: The above table provides general guidelines only. Always consult
your ICI Paints Representative for appropriate recoat windows since the
maximum aged recoat time of this product may be significantly shortened or
lengthened by a variety of conditions, including, but not limited to humidity,
surface temperature, and the use of additives or thinners. The use of
accelerators or force curing may shorten the aged recoat of individual
coatings. The above recoat windows may not apply if recoating with a product
other than those listed above. If the maximum aged recoat window is
exceeded, please consult your ICI Paints Representative for appropriate
recommendations to enhance adhesion. Failure to observe these precautions
may result in intercoat delamination.
Shelf Life: Over 12 months at 77°F (25°C) – unopened
Mix Ratio: 1 (base): 1 (converter) – see mixing instructions.
Induction: None required
Pot Life: 30-45 minutes @ 77°F (25°C) and 50% R.H.
Limitations of Use: Color change may occur with chemical
exposure. Do not apply or cure when air or surface temperature
may go below 50°F (10°C) or chemical resistance may be
compromised.
Adhesion (ASTM D 4541) – Excellent
Abrasion Resistance (ASTM D 4060) – Excellent
Service Temperature Limits: 250°F (121°C) dry
Hardness: (ASTM D 3363), 7 day cure @ 77°F (25°C) – 6H
Read Label and Material Safety Data Sheet Prior to Use. See other cautions on last page. DSF1-0690

All surfaces must be sound, dry, clean, free of oil, grease, dirt, mildew, form release
agents, curing compounds, loose and flaking paint and other foreign substances.
New Surfaces: Concrete – All surfaces must be brush blasted or power scarified. Care
must be taken to ensure that the substrate to be covered is sound, clean and free of all
laitance or other contaminants. Allow new concrete to cure for 30 days minimum. Seal the
properly prepared surface with PRE-PRIME 167 sealer. Steel – Blast to near-white
metal surface cleanliness in accordance with SSPC-SP10 or ISO-Sa2 1/2.
Tinting: Do not tint.
Thinning: Do not thin.
Mixing: DEVRAN ® 124 coating is a two-component product supplied in two gallon
and ten gallon kits which contain the proper ratio of ingredients. The entire contents
of each container must be mixed together.
Mix part A and part B together thoroughly, being sure to scrape the sides and bottom
of the container. Continue mixing for another couple of minutes to insure a
homogeneous mixture that is properly mixed. Mix the materials with slow speed
mixing equipment in order to minimize air being whipped into the coating. Avoid
storing or placing containers in direct sunlight.
Application: Optimum application properties and working life of the coating are
obtained when the mixed components are at 77°F (25°C). At extreme temperatures,
efforts should be made to maintain mixed material at 77°F (25°C).
DEVRAN 124 can be applied to floors and decks with a spreader, squeegee or roller.
Be sure to apply this product at the recommended thickness. If air entrapment is
encountered, use a “porcupine” or another type of air release roller tool; where plural
component airless spray equipment is used, a 45 to 1 pump equipped with a 1 to 1
cylinder pump should be used. All plural component applications require a volumetric
check of the mix ratio. Do not apply or cure when air or surface temperature may go
below 50°F (10°C) or chemical resistance may be compromised.
A minimum of 24 hours cure at temperatures above 77°F
GENERAL SURFACE PREPARATION
DIRECTIONS FOR USE
PRECAUTIONS
Back Page: 124B2216/124C0910
Blast profile on steel should be 1.5 – 2.5 mils (38-62 microns) in depth and be of a
sharp, jagged, nature as opposed to a “peen” pattern (from shot blasting). Surfaces
must be free of grit dust. The first coat of the system should be applied to cleaned
surfaces as soon as possible to prevent re-rusting or contamination.
Previously Painted Surfaces: Remove old paint and prepare as under New
Surfaces.
(25°C) is required before the DEVRAN 124 can withstand light traffic. Full chemical
resistance is achieved only after 7 days cure at 77°F (25°C).
Although DEVRAN 124 coating is solventless, good ventilation with dry air is required for
the protection of the applicator, to prevent condensation and to obtain proper coating
performance. Ventilation should be maintained throughout the cure period. Be sure the
air in the lowest areas is constantly replaced with fresh, dry air.
Longer curing times with ventilation are required if temperatures are lower than 77°F
(25°C). Do not allow coating to remain in the application equipment longer than 30
minutes. Flush out all application equipment whenever there is a delay in application.
When applying specialized sealer coats for anti-slips and chemical resistant properties,
be sure to follow recommended recoat intervals.
Spreading Rate: Apply at 64-80 sq. ft. per gallon (1.57-1.96 m 2 /L) 20.0-25.0 mils (500-
625 microns) dry, 20.0-25.0 mils (500-625 microns) wet. Make allowances for any losses
due to overspray or surface irregularities.
Topcoats: None Recommended
Dry Time (ASTM D 1640): At 77°F (25°C) & 50% R.H., dries to touch in 8 hours, dries
hard in 18-22 hours. Dry to light traffic in 24 hours and reaches full cure in 7 days.
Clean-up: Clean immediately with T-10 thinner, except in the South Coast Air Quality
Management District use acetone or other solvent in compliance with local VOC and air
quality regulations.
WARNING! CORROSIVE. CAUSES EYE AND SKIN BURNS. HARMFUL OR FATAL IF SWALLOWED. ASPIRATION HAZARD-CAN ENTER LUNGS AND CAUSE DAMAGE.
HARMFUL IF INHALED. MAY CAUSE CENTRAL NERVOUS SYSTEM EFFECTS, INCLUDING DIZZINESS, HEADACHE OR NAUSEA. CAUSES RESPIRATORY TRACT
IRRITATION. MAY CAUSE ALLERGIC SKIN REACTION. OVEREXPOSURE MAY CAUSE LIVER, KIDNEY DAMAGE. USE ONLY WITH ADEQUATE VENTILATION. KEEP
OUT OF THE REACH OF CHILDREN. NOTICE: Products in this series contain solvents. Reports have associated repeated and prolonged occupational overexposure to
solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. For emergency
information call (800) 545-2643. Note: These warnings encompass the product series. Prior to use, read and follow product-specific MSDS and label information. If
sanding is done, wear a dust mask to avoid breathing of sanding dust. Do not breathe vapors or spray mist. Ensure fresh air entry during application and drying. Avoid contact with
eyes and skin. If you experience eye watering, headaches, or dizziness, leave the area. If properly used, a respirator may offer additional protection. Obtain professional advice
before using. Close container after each use. FIRST AID: In case of skin contact, wash thoroughly with soap and water. If any product remains, gently rub petroleum jelly, vegetable
or mineral/baby oil onto skin, then wash again with soap and water. Repeated applications may be needed. Remove contaminated clothing. For eye contact, flush immediately with
large amounts of water, for at least 15 minutes. Obtain emergency medical treatment. If swallowed, obtain medical treatment immediately. If inhalation causes physical
discomfort, remove to fresh air. If discomfort persists or any breathing difficulty occurs, get medical help. KEEP FROM FREEZING.
DS360-1003
SHIPPING
Flash Point: 200°F (93°C)
Shipping Weight: 2 - 2 gallon kits - 52 lbs. (23.6 kg)
Packaging: 2 gallon kit (7.57L) 10 gallon kit (37.85L) 10 gallon kit - 121 lbs. (55 kg)
1 gallon base 5 gallon base
1 gallon converter 5 gallon converter
124 (5/07)
Ad Stock #68670E